PCI: Remove MRRS modification from MPS setting code
Modifying the Maximum Read Request Size to 0 (value of 128Bytes) has
massive negative ramifications on some devices. Without knowing which
devices have this issue, do not modify from the default value when
walking the PCI-E bus in pcie_bus_safe mode. Also, make pcie_bus_safe
the default procedure.
Tested-by: Sven Schnelle <svens@stackframe.org>
Tested-by: Simon Kirby <sim@hostway.ca>
Tested-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-and-tested-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
References: https://bugzilla.kernel.org/show_bug.cgi?id=42162
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
index 0820fc1..b1187ff 100644
--- a/drivers/pci/probe.c
+++ b/drivers/pci/probe.c
@@ -1396,34 +1396,37 @@
static void pcie_write_mrrs(struct pci_dev *dev, int mps)
{
- int rc, mrrs;
+ int rc, mrrs, dev_mpss;
- if (pcie_bus_config == PCIE_BUS_PERFORMANCE) {
- int dev_mpss = 128 << dev->pcie_mpss;
+ /* In the "safe" case, do not configure the MRRS. There appear to be
+ * issues with setting MRRS to 0 on a number of devices.
+ */
- /* For Max performance, the MRRS must be set to the largest
- * supported value. However, it cannot be configured larger
- * than the MPS the device or the bus can support. This assumes
- * that the largest MRRS available on the device cannot be
- * smaller than the device MPSS.
- */
- mrrs = mps < dev_mpss ? mps : dev_mpss;
- } else
- /* In the "safe" case, configure the MRRS for fairness on the
- * bus by making all devices have the same size
- */
- mrrs = mps;
+ if (pcie_bus_config != PCIE_BUS_PERFORMANCE)
+ return;
+ dev_mpss = 128 << dev->pcie_mpss;
+
+ /* For Max performance, the MRRS must be set to the largest supported
+ * value. However, it cannot be configured larger than the MPS the
+ * device or the bus can support. This assumes that the largest MRRS
+ * available on the device cannot be smaller than the device MPSS.
+ */
+ mrrs = min(mps, dev_mpss);
/* MRRS is a R/W register. Invalid values can be written, but a
- * subsiquent read will verify if the value is acceptable or not.
+ * subsequent read will verify if the value is acceptable or not.
* If the MRRS value provided is not acceptable (e.g., too large),
* shrink the value until it is acceptable to the HW.
*/
while (mrrs != pcie_get_readrq(dev) && mrrs >= 128) {
+ dev_warn(&dev->dev, "Attempting to modify the PCI-E MRRS value"
+ " to %d. If any issues are encountered, please try "
+ "running with pci=pcie_bus_safe\n", mrrs);
rc = pcie_set_readrq(dev, mrrs);
if (rc)
- dev_err(&dev->dev, "Failed attempting to set the MRRS\n");
+ dev_err(&dev->dev,
+ "Failed attempting to set the MRRS\n");
mrrs /= 2;
}
@@ -1436,13 +1439,13 @@
if (!pci_is_pcie(dev))
return 0;
- dev_info(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n",
+ dev_dbg(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n",
pcie_get_mps(dev), 128<<dev->pcie_mpss, pcie_get_readrq(dev));
pcie_write_mps(dev, mps);
pcie_write_mrrs(dev, mps);
- dev_info(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n",
+ dev_dbg(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n",
pcie_get_mps(dev), 128<<dev->pcie_mpss, pcie_get_readrq(dev));
return 0;