Add more support for the Yukon Ultra chip found in dual core centino laptops.
The newest Yukon Ultra chipset's require more special tweaks.
They seem to be like the Yukon XL chipsets. This code is transliterated
from the latest SysKonnect driver; I don't have any Ultra hardware.
Signed-off-by: Stephe Hemminger <shemminger@osdl.org>
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c
index 9b16c2a..16a99f1e 100644
--- a/drivers/net/sky2.c
+++ b/drivers/net/sky2.c
@@ -304,7 +304,8 @@
struct sky2_port *sky2 = netdev_priv(hw->dev[port]);
u16 ctrl, ct1000, adv, pg, ledctrl, ledover;
- if (sky2->autoneg == AUTONEG_ENABLE && hw->chip_id != CHIP_ID_YUKON_XL) {
+ if (sky2->autoneg == AUTONEG_ENABLE &&
+ (hw->chip_id != CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) {
u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL);
ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK |
@@ -332,7 +333,7 @@
ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO);
if (sky2->autoneg == AUTONEG_ENABLE &&
- hw->chip_id == CHIP_ID_YUKON_XL) {
+ (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)) {
ctrl &= ~PHY_M_PC_DSC_MSK;
ctrl |= PHY_M_PC_DSC(2) | PHY_M_PC_DOWN_S_ENA;
}
@@ -448,10 +449,11 @@
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
/* set LED Function Control register */
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
- PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
- PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
- PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
+ (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
+ PHY_M_LEDC_INIT_CTRL(7) | /* 10 Mbps */
+ PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
+ PHY_M_LEDC_STA0_CTRL(7))); /* 1000 Mbps */
/* set Polarity Control register */
gm_phy_write(hw, port, PHY_MARV_PHY_STAT,
@@ -465,6 +467,25 @@
/* restore page register */
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
break;
+ case CHIP_ID_YUKON_EC_U:
+ pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+
+ /* select page 3 to access LED control register */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
+
+ /* set LED Function Control register */
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL,
+ (PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
+ PHY_M_LEDC_INIT_CTRL(8) | /* 10 Mbps */
+ PHY_M_LEDC_STA1_CTRL(7) | /* 100 Mbps */
+ PHY_M_LEDC_STA0_CTRL(7)));/* 1000 Mbps */
+
+ /* set Blink Rate in LED Timer Control Register */
+ gm_phy_write(hw, port, PHY_MARV_INT_MASK,
+ ledctrl | PHY_M_LED_BLINK_RT(BLINK_84MS));
+ /* restore page register */
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
+ break;
default:
/* set Tx LED (LED_TX) to blink mode on Rx OR Tx activity */
@@ -473,19 +494,21 @@
ledover |= PHY_M_LED_MO_RX(MO_LED_OFF);
}
- if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev >= 2) {
+ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == CHIP_REV_YU_EC_A1) {
/* apply fixes in PHY AFE */
- gm_phy_write(hw, port, 22, 255);
+ pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 255);
+
/* increase differential signal amplitude in 10BASE-T */
- gm_phy_write(hw, port, 24, 0xaa99);
- gm_phy_write(hw, port, 23, 0x2011);
+ gm_phy_write(hw, port, 0x18, 0xaa99);
+ gm_phy_write(hw, port, 0x17, 0x2011);
/* fix for IEEE A/B Symmetry failure in 1000BASE-T */
- gm_phy_write(hw, port, 24, 0xa204);
- gm_phy_write(hw, port, 23, 0x2002);
+ gm_phy_write(hw, port, 0x18, 0xa204);
+ gm_phy_write(hw, port, 0x17, 0x2002);
/* set page register to 0 */
- gm_phy_write(hw, port, 22, 0);
+ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
} else {
gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl);
@@ -559,6 +582,11 @@
if (sky2->duplex == DUPLEX_FULL)
reg |= GM_GPCR_DUP_FULL;
+
+ /* turn off pause in 10/100mbps half duplex */
+ else if (sky2->speed != SPEED_1000 &&
+ hw->chip_id != CHIP_ID_YUKON_EC_U)
+ sky2->tx_pause = sky2->rx_pause = 0;
} else
reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL;
@@ -1504,17 +1532,26 @@
sky2_write8(hw, SK_REG(port, LNK_LED_REG),
LINKLED_ON | LINKLED_BLINK_OFF | LINKLED_LINKSYNC_OFF);
- if (hw->chip_id == CHIP_ID_YUKON_XL) {
+ if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U) {
u16 pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR);
+ u16 led = PHY_M_LEDC_LOS_CTRL(1); /* link active */
+
+ switch(sky2->speed) {
+ case SPEED_10:
+ led |= PHY_M_LEDC_INIT_CTRL(7);
+ break;
+
+ case SPEED_100:
+ led |= PHY_M_LEDC_STA1_CTRL(7);
+ break;
+
+ case SPEED_1000:
+ led |= PHY_M_LEDC_STA0_CTRL(7);
+ break;
+ }
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 3);
- gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, PHY_M_LEDC_LOS_CTRL(1) | /* LINK/ACT */
- PHY_M_LEDC_INIT_CTRL(sky2->speed ==
- SPEED_10 ? 7 : 0) |
- PHY_M_LEDC_STA1_CTRL(sky2->speed ==
- SPEED_100 ? 7 : 0) |
- PHY_M_LEDC_STA0_CTRL(sky2->speed ==
- SPEED_1000 ? 7 : 0));
+ gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, led);
gm_phy_write(hw, port, PHY_MARV_EXT_ADR, pg);
}
@@ -1589,7 +1626,7 @@
sky2->speed = sky2_phy_speed(hw, aux);
/* Pause bits are offset (9..8) */
- if (hw->chip_id == CHIP_ID_YUKON_XL)
+ if (hw->chip_id == CHIP_ID_YUKON_XL || hw->chip_id == CHIP_ID_YUKON_EC_U)
aux >>= 6;
sky2->rx_pause = (aux & PHY_M_PS_RX_P_EN) != 0;
@@ -2226,13 +2263,6 @@
return -EOPNOTSUPP;
}
- /* This chip is new and not tested yet */
- if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
- pr_info(PFX "%s: is a version of Yukon 2 chipset that has not been tested yet.\n",
- pci_name(hw->pdev));
- pr_info("Please report success/failure to maintainer <shemminger@osdl.org>\n");
- }
-
/* disable ASF */
if (hw->chip_id <= CHIP_ID_YUKON_EC) {
sky2_write8(hw, B28_Y2_ASF_STAT_CMD, Y2_ASF_RESET);
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index b026f56..8012994 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -378,6 +378,9 @@
CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */
CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */
CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */
+
+ CHIP_REV_YU_EC_U_A0 = 0,
+ CHIP_REV_YU_EC_U_A1 = 1,
};
/* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */