iwlwifi: mvm: several fixes in scan
The firmware doesn't handle properly the fragmented scan.
Stop using it.
While at it change max_out_time and suspend_time units from
usec to TUs as expected by firmware API.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
diff --git a/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h b/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h
index 9426905..d73a89e 100644
--- a/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h
+++ b/drivers/net/wireless/iwlwifi/mvm/fw-api-scan.h
@@ -183,9 +183,9 @@
* this number of packets were received (typically 1)
* @passive2active: is auto switching from passive to active during scan allowed
* @rxchain_sel_flags: RXON_RX_CHAIN_*
- * @max_out_time: in usecs, max out of serving channel time
+ * @max_out_time: in TUs, max out of serving channel time
* @suspend_time: how long to pause scan when returning to service channel:
- * bits 0-19: beacon interal in usecs (suspend before executing)
+ * bits 0-19: beacon interal in TUs (suspend before executing)
* bits 20-23: reserved
* bits 24-31: number of beacons (suspend between channels)
* @rxon_flags: RXON_FLG_*
@@ -383,8 +383,8 @@
* @quiet_plcp_th: quiet channel num of packets threshold
* @good_CRC_th: passive to active promotion threshold
* @rx_chain: RXON rx chain.
- * @max_out_time: max uSec to be out of assoceated channel
- * @suspend_time: pause scan this long when returning to service channel
+ * @max_out_time: max TUs to be out of assoceated channel
+ * @suspend_time: pause scan this TUs when returning to service channel
* @flags: RXON flags
* @filter_flags: RXONfilter
* @tx_cmd: tx command for active scan; for 2GHz and for 5GHz.
diff --git a/drivers/net/wireless/iwlwifi/mvm/scan.c b/drivers/net/wireless/iwlwifi/mvm/scan.c
index c91dc84..cba88a3 100644
--- a/drivers/net/wireless/iwlwifi/mvm/scan.c
+++ b/drivers/net/wireless/iwlwifi/mvm/scan.c
@@ -277,51 +277,22 @@
IEEE80211_IFACE_ITER_NORMAL,
iwl_mvm_scan_condition_iterator,
&global_bound);
- /*
- * Under low latency traffic passive scan is fragmented meaning
- * that dwell on a particular channel will be fragmented. Each fragment
- * dwell time is 20ms and fragments period is 105ms. Skipping to next
- * channel will be delayed by the same period - 105ms. So suspend_time
- * parameter describing both fragments and channels skipping periods is
- * set to 105ms. This value is chosen so that overall passive scan
- * duration will not be too long. Max_out_time in this case is set to
- * 70ms, so for active scanning operating channel will be left for 70ms
- * while for passive still for 20ms (fragment dwell).
- */
- if (global_bound) {
- if (!iwl_mvm_low_latency(mvm)) {
- params->suspend_time = ieee80211_tu_to_usec(100);
- params->max_out_time = ieee80211_tu_to_usec(600);
- } else {
- params->suspend_time = ieee80211_tu_to_usec(105);
- /* P2P doesn't support fragmented passive scan, so
- * configure max_out_time to be at least longest dwell
- * time for passive scan.
- */
- if (vif->type == NL80211_IFTYPE_STATION && !vif->p2p) {
- params->max_out_time = ieee80211_tu_to_usec(70);
- params->passive_fragmented = true;
- } else {
- u32 passive_dwell;
- /*
- * Use band G so that passive channel dwell time
- * will be assigned with maximum value.
- */
- band = IEEE80211_BAND_2GHZ;
- passive_dwell = iwl_mvm_get_passive_dwell(band);
- params->max_out_time =
- ieee80211_tu_to_usec(passive_dwell);
- }
- }
+ if (!global_bound)
+ goto not_bound;
+
+ params->suspend_time = 100;
+ params->max_out_time = 600;
+
+ if (iwl_mvm_low_latency(mvm)) {
+ params->suspend_time = 250;
+ params->max_out_time = 250;
}
+not_bound:
+
for (band = IEEE80211_BAND_2GHZ; band < IEEE80211_NUM_BANDS; band++) {
- if (params->passive_fragmented)
- params->dwell[band].passive = 20;
- else
- params->dwell[band].passive =
- iwl_mvm_get_passive_dwell(band);
+ params->dwell[band].passive = iwl_mvm_get_passive_dwell(band);
params->dwell[band].active = iwl_mvm_get_active_dwell(band,
n_ssids);
}