blob: 256b7f69e45b4cba84b2bfa85543545374ce6f02 [file] [log] [blame]
/*
* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
* Based on "omap4.dtsi"
*/
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/omap.h>
#include "skeleton.dtsi"
/ {
#address-cells = <1>;
#size-cells = <1>;
compatible = "ti,omap5";
interrupt-parent = <&gic>;
aliases {
i2c0 = &i2c1;
i2c1 = &i2c2;
i2c2 = &i2c3;
i2c3 = &i2c4;
i2c4 = &i2c5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
serial3 = &uart4;
serial4 = &uart5;
serial5 = &uart6;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
cpu0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x0>;
operating-points = <
/* kHz uV */
1000000 1060000
1500000 1250000
>;
clocks = <&dpll_mpu_ck>;
clock-names = "cpu";
clock-latency = <300000>; /* From omap-cpufreq driver */
/* cooling options */
cooling-min-level = <0>;
cooling-max-level = <2>;
#cooling-cells = <2>; /* min followed by max */
};
cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a15";
reg = <0x1>;
};
};
thermal-zones {
#include "omap4-cpu-thermal.dtsi"
#include "omap5-gpu-thermal.dtsi"
#include "omap5-core-thermal.dtsi"
};
timer {
compatible = "arm,armv7-timer";
/* PPI secure/nonsecure IRQ */
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
};
pmu {
compatible = "arm,cortex-a15-pmu";
interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
};
gic: interrupt-controller@48211000 {
compatible = "arm,cortex-a15-gic";
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x48211000 0x1000>,
<0x48212000 0x1000>,
<0x48214000 0x2000>,
<0x48216000 0x2000>;
};
/*
* The soc node represents the soc top level view. It is used for IPs
* that are not memory mapped in the MPU view or for the MPU itself.
*/
soc {
compatible = "ti,omap-infra";
mpu {
compatible = "ti,omap4-mpu";
ti,hwmods = "mpu";
sram = <&ocmcram>;
};
};
/*
* XXX: Use a flat representation of the OMAP3 interconnect.
* The real OMAP interconnect network is quite complex.
* Since it will not bring real advantage to represent that in DT for
* the moment, just use a fake OCP bus entry to represent the whole bus
* hierarchy.
*/
ocp {
compatible = "ti,omap4-l3-noc", "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
reg = <0x44000000 0x2000>,
<0x44800000 0x3000>,
<0x45000000 0x4000>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
prm: prm@4ae06000 {
compatible = "ti,omap5-prm";
reg = <0x4ae06000 0x3000>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
prm_clocks: clocks {
#address-cells = <1>;
#size-cells = <0>;
};
prm_clockdomains: clockdomains {
};
};
cm_core_aon: cm_core_aon@4a004000 {
compatible = "ti,omap5-cm-core-aon";
reg = <0x4a004000 0x2000>;
cm_core_aon_clocks: clocks {
#address-cells = <1>;
#size-cells = <0>;
};
cm_core_aon_clockdomains: clockdomains {
};
};
scrm: scrm@4ae0a000 {
compatible = "ti,omap5-scrm";
reg = <0x4ae0a000 0x2000>;
scrm_clocks: clocks {
#address-cells = <1>;
#size-cells = <0>;
};
scrm_clockdomains: clockdomains {
};
};
cm_core: cm_core@4a008000 {
compatible = "ti,omap5-cm-core";
reg = <0x4a008000 0x3000>;
cm_core_clocks: clocks {
#address-cells = <1>;
#size-cells = <0>;
};
cm_core_clockdomains: clockdomains {
};
};
counter32k: counter@4ae04000 {
compatible = "ti,omap-counter32k";
reg = <0x4ae04000 0x40>;
ti,hwmods = "counter_32k";
};
omap5_pmx_core: pinmux@4a002840 {
compatible = "ti,omap5-padconf", "pinctrl-single";
reg = <0x4a002840 0x01b6>;
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x7fff>;
};
omap5_pmx_wkup: pinmux@4ae0c840 {
compatible = "ti,omap5-padconf", "pinctrl-single";
reg = <0x4ae0c840 0x0038>;
#address-cells = <1>;
#size-cells = <0>;
#interrupt-cells = <1>;
interrupt-controller;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x7fff>;
};
omap5_padconf_global: tisyscon@4a002da0 {
compatible = "syscon";
reg = <0x4A002da0 0xec>;
};
pbias_regulator: pbias_regulator {
compatible = "ti,pbias-omap";
reg = <0x60 0x4>;
syscon = <&omap5_padconf_global>;
pbias_mmc_reg: pbias_mmc_omap5 {
regulator-name = "pbias_mmc_omap5";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3000000>;
};
};
ocmcram: ocmcram@40300000 {
compatible = "mmio-sram";
reg = <0x40300000 0x20000>; /* 128k */
};
sdma: dma-controller@4a056000 {
compatible = "ti,omap4430-sdma";
reg = <0x4a056000 0x1000>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
#dma-channels = <32>;
#dma-requests = <127>;
};
gpio1: gpio@4ae10000 {
compatible = "ti,omap4-gpio";
reg = <0x4ae10000 0x200>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio1";
ti,gpio-always-on;
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio2: gpio@48055000 {
compatible = "ti,omap4-gpio";
reg = <0x48055000 0x200>;
interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio2";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio3: gpio@48057000 {
compatible = "ti,omap4-gpio";
reg = <0x48057000 0x200>;
interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio3";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio4: gpio@48059000 {
compatible = "ti,omap4-gpio";
reg = <0x48059000 0x200>;
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio4";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio5: gpio@4805b000 {
compatible = "ti,omap4-gpio";
reg = <0x4805b000 0x200>;
interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio5";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio6: gpio@4805d000 {
compatible = "ti,omap4-gpio";
reg = <0x4805d000 0x200>;
interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio6";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio7: gpio@48051000 {
compatible = "ti,omap4-gpio";
reg = <0x48051000 0x200>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio7";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpio8: gpio@48053000 {
compatible = "ti,omap4-gpio";
reg = <0x48053000 0x200>;
interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "gpio8";
gpio-controller;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
gpmc: gpmc@50000000 {
compatible = "ti,omap4430-gpmc";
reg = <0x50000000 0x1000>;
#address-cells = <2>;
#size-cells = <1>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
ti,hwmods = "gpmc";
clocks = <&l3_iclk_div>;
clock-names = "fck";
};
i2c1: i2c@48070000 {
compatible = "ti,omap4-i2c";
reg = <0x48070000 0x100>;
interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c1";
};
i2c2: i2c@48072000 {
compatible = "ti,omap4-i2c";
reg = <0x48072000 0x100>;
interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c2";
};
i2c3: i2c@48060000 {
compatible = "ti,omap4-i2c";
reg = <0x48060000 0x100>;
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c3";
};
i2c4: i2c@4807a000 {
compatible = "ti,omap4-i2c";
reg = <0x4807a000 0x100>;
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c4";
};
i2c5: i2c@4807c000 {
compatible = "ti,omap4-i2c";
reg = <0x4807c000 0x100>;
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "i2c5";
};
hwspinlock: spinlock@4a0f6000 {
compatible = "ti,omap4-hwspinlock";
reg = <0x4a0f6000 0x1000>;
ti,hwmods = "spinlock";
#hwlock-cells = <1>;
};
mcspi1: spi@48098000 {
compatible = "ti,omap4-mcspi";
reg = <0x48098000 0x200>;
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi1";
ti,spi-num-cs = <4>;
dmas = <&sdma 35>,
<&sdma 36>,
<&sdma 37>,
<&sdma 38>,
<&sdma 39>,
<&sdma 40>,
<&sdma 41>,
<&sdma 42>;
dma-names = "tx0", "rx0", "tx1", "rx1",
"tx2", "rx2", "tx3", "rx3";
};
mcspi2: spi@4809a000 {
compatible = "ti,omap4-mcspi";
reg = <0x4809a000 0x200>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi2";
ti,spi-num-cs = <2>;
dmas = <&sdma 43>,
<&sdma 44>,
<&sdma 45>,
<&sdma 46>;
dma-names = "tx0", "rx0", "tx1", "rx1";
};
mcspi3: spi@480b8000 {
compatible = "ti,omap4-mcspi";
reg = <0x480b8000 0x200>;
interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi3";
ti,spi-num-cs = <2>;
dmas = <&sdma 15>, <&sdma 16>;
dma-names = "tx0", "rx0";
};
mcspi4: spi@480ba000 {
compatible = "ti,omap4-mcspi";
reg = <0x480ba000 0x200>;
interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
ti,hwmods = "mcspi4";
ti,spi-num-cs = <1>;
dmas = <&sdma 70>, <&sdma 71>;
dma-names = "tx0", "rx0";
};
uart1: serial@4806a000 {
compatible = "ti,omap4-uart";
reg = <0x4806a000 0x100>;
interrupts-extended = <&gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "uart1";
clock-frequency = <48000000>;
};
uart2: serial@4806c000 {
compatible = "ti,omap4-uart";
reg = <0x4806c000 0x100>;
interrupts-extended = <&gic GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "uart2";
clock-frequency = <48000000>;
};
uart3: serial@48020000 {
compatible = "ti,omap4-uart";
reg = <0x48020000 0x100>;
interrupts-extended = <&gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "uart3";
clock-frequency = <48000000>;
};
uart4: serial@4806e000 {
compatible = "ti,omap4-uart";
reg = <0x4806e000 0x100>;
interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "uart4";
clock-frequency = <48000000>;
};
uart5: serial@48066000 {
compatible = "ti,omap4-uart";
reg = <0x48066000 0x100>;
interrupts-extended = <&gic GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "uart5";
clock-frequency = <48000000>;
};
uart6: serial@48068000 {
compatible = "ti,omap4-uart";
reg = <0x48068000 0x100>;
interrupts-extended = <&gic GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "uart6";
clock-frequency = <48000000>;
};
mmc1: mmc@4809c000 {
compatible = "ti,omap4-hsmmc";
reg = <0x4809c000 0x400>;
interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmc1";
ti,dual-volt;
ti,needs-special-reset;
dmas = <&sdma 61>, <&sdma 62>;
dma-names = "tx", "rx";
pbias-supply = <&pbias_mmc_reg>;
};
mmc2: mmc@480b4000 {
compatible = "ti,omap4-hsmmc";
reg = <0x480b4000 0x400>;
interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmc2";
ti,needs-special-reset;
dmas = <&sdma 47>, <&sdma 48>;
dma-names = "tx", "rx";
};
mmc3: mmc@480ad000 {
compatible = "ti,omap4-hsmmc";
reg = <0x480ad000 0x400>;
interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmc3";
ti,needs-special-reset;
dmas = <&sdma 77>, <&sdma 78>;
dma-names = "tx", "rx";
};
mmc4: mmc@480d1000 {
compatible = "ti,omap4-hsmmc";
reg = <0x480d1000 0x400>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmc4";
ti,needs-special-reset;
dmas = <&sdma 57>, <&sdma 58>;
dma-names = "tx", "rx";
};
mmc5: mmc@480d5000 {
compatible = "ti,omap4-hsmmc";
reg = <0x480d5000 0x400>;
interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmc5";
ti,needs-special-reset;
dmas = <&sdma 59>, <&sdma 60>;
dma-names = "tx", "rx";
};
mmu_dsp: mmu@4a066000 {
compatible = "ti,omap4-iommu";
reg = <0x4a066000 0x100>;
interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmu_dsp";
};
mmu_ipu: mmu@55082000 {
compatible = "ti,omap4-iommu";
reg = <0x55082000 0x100>;
interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mmu_ipu";
ti,iommu-bus-err-back;
};
keypad: keypad@4ae1c000 {
compatible = "ti,omap4-keypad";
reg = <0x4ae1c000 0x400>;
ti,hwmods = "kbd";
};
mcpdm: mcpdm@40132000 {
compatible = "ti,omap4-mcpdm";
reg = <0x40132000 0x7f>, /* MPU private access */
<0x49032000 0x7f>; /* L3 Interconnect */
reg-names = "mpu", "dma";
interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mcpdm";
dmas = <&sdma 65>,
<&sdma 66>;
dma-names = "up_link", "dn_link";
status = "disabled";
};
dmic: dmic@4012e000 {
compatible = "ti,omap4-dmic";
reg = <0x4012e000 0x7f>, /* MPU private access */
<0x4902e000 0x7f>; /* L3 Interconnect */
reg-names = "mpu", "dma";
interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "dmic";
dmas = <&sdma 67>;
dma-names = "up_link";
status = "disabled";
};
mcbsp1: mcbsp@40122000 {
compatible = "ti,omap4-mcbsp";
reg = <0x40122000 0xff>, /* MPU private access */
<0x49022000 0xff>; /* L3 Interconnect */
reg-names = "mpu", "dma";
interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp1";
dmas = <&sdma 33>,
<&sdma 34>;
dma-names = "tx", "rx";
status = "disabled";
};
mcbsp2: mcbsp@40124000 {
compatible = "ti,omap4-mcbsp";
reg = <0x40124000 0xff>, /* MPU private access */
<0x49024000 0xff>; /* L3 Interconnect */
reg-names = "mpu", "dma";
interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp2";
dmas = <&sdma 17>,
<&sdma 18>;
dma-names = "tx", "rx";
status = "disabled";
};
mcbsp3: mcbsp@40126000 {
compatible = "ti,omap4-mcbsp";
reg = <0x40126000 0xff>, /* MPU private access */
<0x49026000 0xff>; /* L3 Interconnect */
reg-names = "mpu", "dma";
interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "common";
ti,buffer-size = <128>;
ti,hwmods = "mcbsp3";
dmas = <&sdma 19>,
<&sdma 20>;
dma-names = "tx", "rx";
status = "disabled";
};
mailbox: mailbox@4a0f4000 {
compatible = "ti,omap4-mailbox";
reg = <0x4a0f4000 0x200>;
interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "mailbox";
ti,mbox-num-users = <3>;
ti,mbox-num-fifos = <8>;
mbox_ipu: mbox_ipu {
ti,mbox-tx = <0 0 0>;
ti,mbox-rx = <1 0 0>;
};
mbox_dsp: mbox_dsp {
ti,mbox-tx = <3 0 0>;
ti,mbox-rx = <2 0 0>;
};
};
timer1: timer@4ae18000 {
compatible = "ti,omap5430-timer";
reg = <0x4ae18000 0x80>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer1";
ti,timer-alwon;
};
timer2: timer@48032000 {
compatible = "ti,omap5430-timer";
reg = <0x48032000 0x80>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer2";
};
timer3: timer@48034000 {
compatible = "ti,omap5430-timer";
reg = <0x48034000 0x80>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer3";
};
timer4: timer@48036000 {
compatible = "ti,omap5430-timer";
reg = <0x48036000 0x80>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer4";
};
timer5: timer@40138000 {
compatible = "ti,omap5430-timer";
reg = <0x40138000 0x80>,
<0x49038000 0x80>;
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer5";
ti,timer-dsp;
ti,timer-pwm;
};
timer6: timer@4013a000 {
compatible = "ti,omap5430-timer";
reg = <0x4013a000 0x80>,
<0x4903a000 0x80>;
interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer6";
ti,timer-dsp;
ti,timer-pwm;
};
timer7: timer@4013c000 {
compatible = "ti,omap5430-timer";
reg = <0x4013c000 0x80>,
<0x4903c000 0x80>;
interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer7";
ti,timer-dsp;
};
timer8: timer@4013e000 {
compatible = "ti,omap5430-timer";
reg = <0x4013e000 0x80>,
<0x4903e000 0x80>;
interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer8";
ti,timer-dsp;
ti,timer-pwm;
};
timer9: timer@4803e000 {
compatible = "ti,omap5430-timer";
reg = <0x4803e000 0x80>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer9";
ti,timer-pwm;
};
timer10: timer@48086000 {
compatible = "ti,omap5430-timer";
reg = <0x48086000 0x80>;
interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer10";
ti,timer-pwm;
};
timer11: timer@48088000 {
compatible = "ti,omap5430-timer";
reg = <0x48088000 0x80>;
interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer11";
ti,timer-pwm;
};
wdt2: wdt@4ae14000 {
compatible = "ti,omap5-wdt", "ti,omap3-wdt";
reg = <0x4ae14000 0x80>;
interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "wd_timer2";
};
dmm@4e000000 {
compatible = "ti,omap5-dmm";
reg = <0x4e000000 0x800>;
interrupts = <0 113 0x4>;
ti,hwmods = "dmm";
};
emif1: emif@4c000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif1";
ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4c000000 0x400>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
hw-caps-temp-alert;
};
emif2: emif@4d000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif2";
ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4d000000 0x400>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
hw-caps-temp-alert;
};
omap_control_usb2phy: control-phy@4a002300 {
compatible = "ti,control-phy-usb2";
reg = <0x4a002300 0x4>;
reg-names = "power";
};
omap_control_usb3phy: control-phy@4a002370 {
compatible = "ti,control-phy-pipe3";
reg = <0x4a002370 0x4>;
reg-names = "power";
};
usb3: omap_dwc3@4a020000 {
compatible = "ti,dwc3";
ti,hwmods = "usb_otg_ss";
reg = <0x4a020000 0x10000>;
interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
#address-cells = <1>;
#size-cells = <1>;
utmi-mode = <2>;
ranges;
dwc3@4a030000 {
compatible = "snps,dwc3";
reg = <0x4a030000 0x10000>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb2_phy>, <&usb3_phy>;
phy-names = "usb2-phy", "usb3-phy";
dr_mode = "peripheral";
tx-fifo-resize;
};
};
ocp2scp@4a080000 {
compatible = "ti,omap-ocp2scp";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x4a080000 0x20>;
ranges;
ti,hwmods = "ocp2scp1";
usb2_phy: usb2phy@4a084000 {
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x7c>;
ctrl-module = <&omap_control_usb2phy>;
clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
clock-names = "wkupclk", "refclk";
#phy-cells = <0>;
};
usb3_phy: usb3phy@4a084400 {
compatible = "ti,omap-usb3";
reg = <0x4a084400 0x80>,
<0x4a084800 0x64>,
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
ctrl-module = <&omap_control_usb3phy>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
<&usb_otg_ss_refclk960m>;
clock-names = "wkupclk",
"sysclk",
"refclk";
#phy-cells = <0>;
};
};
usbhstll: usbhstll@4a062000 {
compatible = "ti,usbhs-tll";
reg = <0x4a062000 0x1000>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "usb_tll_hs";
};
usbhshost: usbhshost@4a064000 {
compatible = "ti,usbhs-host";
reg = <0x4a064000 0x800>;
ti,hwmods = "usb_host_hs";
#address-cells = <1>;
#size-cells = <1>;
ranges;
clocks = <&l3init_60m_fclk>,
<&xclk60mhsp1_ck>,
<&xclk60mhsp2_ck>;
clock-names = "refclk_60m_int",
"refclk_60m_ext_p1",
"refclk_60m_ext_p2";
usbhsohci: ohci@4a064800 {
compatible = "ti,ohci-omap3";
reg = <0x4a064800 0x400>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
};
usbhsehci: ehci@4a064c00 {
compatible = "ti,ehci-omap";
reg = <0x4a064c00 0x400>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
};
};
bandgap: bandgap@4a0021e0 {
reg = <0x4a0021e0 0xc
0x4a00232c 0xc
0x4a002380 0x2c
0x4a0023C0 0x3c>;
interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
compatible = "ti,omap5430-bandgap";
#thermal-sensor-cells = <1>;
};
omap_control_sata: control-phy@4a002374 {
compatible = "ti,control-phy-pipe3";
reg = <0x4a002374 0x4>;
reg-names = "power";
clocks = <&sys_clkin>;
clock-names = "sysclk";
};
/* OCP2SCP3 */
ocp2scp@4a090000 {
compatible = "ti,omap-ocp2scp";
#address-cells = <1>;
#size-cells = <1>;
reg = <0x4a090000 0x20>;
ranges;
ti,hwmods = "ocp2scp3";
sata_phy: phy@4a096000 {
compatible = "ti,phy-pipe3-sata";
reg = <0x4A096000 0x80>, /* phy_rx */
<0x4A096400 0x64>, /* phy_tx */
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
ctrl-module = <&omap_control_sata>;
clocks = <&sys_clkin>;
clock-names = "sysclk";
#phy-cells = <0>;
};
};
sata: sata@4a141100 {
compatible = "snps,dwc-ahci";
reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
phys = <&sata_phy>;
phy-names = "sata-phy";
clocks = <&sata_ref_clk>;
ti,hwmods = "sata";
};
dss: dss@58000000 {
compatible = "ti,omap5-dss";
reg = <0x58000000 0x80>;
status = "disabled";
ti,hwmods = "dss_core";
clocks = <&dss_dss_clk>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dispc@58001000 {
compatible = "ti,omap5-dispc";
reg = <0x58001000 0x1000>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "dss_dispc";
clocks = <&dss_dss_clk>;
clock-names = "fck";
};
rfbi: encoder@58002000 {
compatible = "ti,omap5-rfbi";
reg = <0x58002000 0x100>;
status = "disabled";
ti,hwmods = "dss_rfbi";
clocks = <&dss_dss_clk>, <&l3_iclk_div>;
clock-names = "fck", "ick";
};
dsi1: encoder@58004000 {
compatible = "ti,omap5-dsi";
reg = <0x58004000 0x200>,
<0x58004200 0x40>,
<0x58004300 0x40>;
reg-names = "proto", "phy", "pll";
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_dsi1";
clocks = <&dss_dss_clk>, <&dss_sys_clk>;
clock-names = "fck", "sys_clk";
};
dsi2: encoder@58005000 {
compatible = "ti,omap5-dsi";
reg = <0x58009000 0x200>,
<0x58009200 0x40>,
<0x58009300 0x40>;
reg-names = "proto", "phy", "pll";
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_dsi2";
clocks = <&dss_dss_clk>, <&dss_sys_clk>;
clock-names = "fck", "sys_clk";
};
hdmi: encoder@58060000 {
compatible = "ti,omap5-hdmi";
reg = <0x58040000 0x200>,
<0x58040200 0x80>,
<0x58040300 0x80>,
<0x58060000 0x19000>;
reg-names = "wp", "pll", "phy", "core";
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_hdmi";
clocks = <&dss_48mhz_clk>, <&dss_sys_clk>;
clock-names = "fck", "sys_clk";
dmas = <&sdma 76>;
dma-names = "audio_tx";
};
};
abb_mpu: regulator-abb-mpu {
compatible = "ti,abb-v2";
regulator-name = "abb_mpu";
#address-cells = <0>;
#size-cells = <0>;
clocks = <&sys_clkin>;
ti,settling-time = <50>;
ti,clock-cycles = <16>;
reg = <0x4ae07cdc 0x8>, <0x4ae06014 0x4>,
<0x4a0021c4 0x8>, <0x4ae0c318 0x4>;
reg-names = "base-address", "int-address",
"efuse-address", "ldo-address";
ti,tranxdone-status-mask = <0x80>;
/* LDOVBBMPU_MUX_CTRL */
ti,ldovbb-override-mask = <0x400>;
/* LDOVBBMPU_VSET_OUT */
ti,ldovbb-vset-mask = <0x1F>;
/*
* NOTE: only FBB mode used but actual vset will
* determine final biasing
*/
ti,abb_info = <
/*uV ABB efuse rbb_m fbb_m vset_m*/
1060000 0 0x0 0 0x02000000 0x01F00000
1250000 0 0x4 0 0x02000000 0x01F00000
>;
};
abb_mm: regulator-abb-mm {
compatible = "ti,abb-v2";
regulator-name = "abb_mm";
#address-cells = <0>;
#size-cells = <0>;
clocks = <&sys_clkin>;
ti,settling-time = <50>;
ti,clock-cycles = <16>;
reg = <0x4ae07ce4 0x8>, <0x4ae06010 0x4>,
<0x4a0021a4 0x8>, <0x4ae0c314 0x4>;
reg-names = "base-address", "int-address",
"efuse-address", "ldo-address";
ti,tranxdone-status-mask = <0x80000000>;
/* LDOVBBMM_MUX_CTRL */
ti,ldovbb-override-mask = <0x400>;
/* LDOVBBMM_VSET_OUT */
ti,ldovbb-vset-mask = <0x1F>;
/*
* NOTE: only FBB mode used but actual vset will
* determine final biasing
*/
ti,abb_info = <
/*uV ABB efuse rbb_m fbb_m vset_m*/
1025000 0 0x0 0 0x02000000 0x01F00000
1120000 0 0x4 0 0x02000000 0x01F00000
>;
};
};
};
/include/ "omap54xx-clocks.dtsi"