wl18xx: ipmlement ap_rate_mask hw op
Enable wide-chan or MIMO rates when appropriate.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
diff --git a/drivers/net/wireless/ti/wl18xx/main.c b/drivers/net/wireless/ti/wl18xx/main.c
index fd7a803..77840dd 100644
--- a/drivers/net/wireless/ti/wl18xx/main.c
+++ b/drivers/net/wireless/ti/wl18xx/main.c
@@ -862,6 +862,23 @@
skb->ip_summed = CHECKSUM_UNNECESSARY;
}
+static u32 wl18xx_sta_get_ap_rate_mask(struct wl1271 *wl,
+ struct wl12xx_vif *wlvif)
+{
+ u32 hw_rate_set = wlvif->rate_set;
+
+ if (wlvif->channel_type == NL80211_CHAN_HT40MINUS ||
+ wlvif->channel_type == NL80211_CHAN_HT40PLUS) {
+ wl1271_debug(DEBUG_ACX, "using wide channel rate mask");
+ hw_rate_set |= CONF_TX_RATE_USE_WIDE_CHAN;
+
+ /* we don't support MIMO in wide-channel mode */
+ hw_rate_set &= ~CONF_TX_MIMO_RATES;
+ }
+
+ return hw_rate_set;
+}
+
static void wl18xx_conf_init(struct wl1271 *wl)
{
struct wl18xx_priv *priv = wl->priv;
@@ -888,6 +905,7 @@
.hw_init = wl18xx_hw_init,
.set_tx_desc_csum = wl18xx_set_tx_desc_csum,
.set_rx_csum = wl18xx_set_rx_csum,
+ .sta_get_ap_rate_mask = wl18xx_sta_get_ap_rate_mask,
};
int __devinit wl18xx_probe(struct platform_device *pdev)
diff --git a/drivers/net/wireless/ti/wl18xx/tx.h b/drivers/net/wireless/ti/wl18xx/tx.h
index a91eb10..2417262 100644
--- a/drivers/net/wireless/ti/wl18xx/tx.h
+++ b/drivers/net/wireless/ti/wl18xx/tx.h
@@ -31,6 +31,12 @@
#define WL18XX_TX_STATUS_DESC_ID_MASK 0x7F
#define WL18XX_TX_STATUS_STAT_BIT_IDX 7
+/*
+ * The FW uses a special bit to indicate a wide channel should be used in
+ * the rate policy.
+ */
+#define CONF_TX_RATE_USE_WIDE_CHAN BIT(31)
+
void wl18xx_tx_immediate_complete(struct wl1271 *wl);
#endif /* __WL12XX_TX_H__ */
diff --git a/drivers/net/wireless/ti/wlcore/conf.h b/drivers/net/wireless/ti/wlcore/conf.h
index 0798c1e..14dd361 100644
--- a/drivers/net/wireless/ti/wlcore/conf.h
+++ b/drivers/net/wireless/ti/wlcore/conf.h
@@ -443,6 +443,12 @@
CONF_HW_BIT_RATE_MCS_5 | CONF_HW_BIT_RATE_MCS_6 | \
CONF_HW_BIT_RATE_MCS_7)
+#define CONF_TX_MIMO_RATES (CONF_HW_BIT_RATE_MCS_8 | \
+ CONF_HW_BIT_RATE_MCS_9 | CONF_HW_BIT_RATE_MCS_10 | \
+ CONF_HW_BIT_RATE_MCS_11 | CONF_HW_BIT_RATE_MCS_12 | \
+ CONF_HW_BIT_RATE_MCS_13 | CONF_HW_BIT_RATE_MCS_14 | \
+ CONF_HW_BIT_RATE_MCS_15)
+
/*
* Default rates for management traffic when operating in AP mode. This
* should be configured according to the basic rate set of the AP