bnx2x: Add 57712 support
57712 HW supported with same set of features as for 57710/57711
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/bnx2x/bnx2x_link.c b/drivers/net/bnx2x/bnx2x_link.c
index 51d468d..3e99bf9 100644
--- a/drivers/net/bnx2x/bnx2x_link.c
+++ b/drivers/net/bnx2x/bnx2x_link.c
@@ -377,9 +377,60 @@
return 0;
}
+static void bnx2x_update_bmac2(struct link_params *params,
+ struct link_vars *vars,
+ u8 is_lb)
+{
+ /*
+ * Set rx control: Strip CRC and enable BigMAC to relay
+ * control packets to the system as well
+ */
+ u32 wb_data[2];
+ struct bnx2x *bp = params->bp;
+ u32 bmac_addr = params->port ? NIG_REG_INGRESS_BMAC1_MEM :
+ NIG_REG_INGRESS_BMAC0_MEM;
+ u32 val = 0x14;
+
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_RX)
+ /* Enable BigMAC to react on received Pause packets */
+ val |= (1<<5);
+ wb_data[0] = val;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_CONTROL,
+ wb_data, 2);
+ udelay(30);
+
+ /* Tx control */
+ val = 0xc0;
+ if (vars->flow_ctrl & BNX2X_FLOW_CTRL_TX)
+ val |= 0x800000;
+ wb_data[0] = val;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_CONTROL,
+ wb_data, 2);
+
+ val = 0x8000;
+ wb_data[0] = val;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_PAUSE_CONTROL,
+ wb_data, 2);
+
+ /* mac control */
+ val = 0x3; /* Enable RX and TX */
+ if (is_lb) {
+ val |= 0x4; /* Local loopback */
+ DP(NETIF_MSG_LINK, "enable bmac loopback\n");
+ }
+
+ wb_data[0] = val;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+}
-static u8 bnx2x_bmac_enable(struct link_params *params, struct link_vars *vars,
+static u8 bnx2x_bmac1_enable(struct link_params *params,
+ struct link_vars *vars,
u8 is_lb)
{
struct bnx2x *bp = params->bp;
@@ -389,17 +440,7 @@
u32 wb_data[2];
u32 val;
- DP(NETIF_MSG_LINK, "Enabling BigMAC\n");
- /* reset and unreset the BigMac */
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
- msleep(1);
-
- REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
- (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
-
- /* enable access for bmac registers */
- REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
+ DP(NETIF_MSG_LINK, "Enabling BigMAC1\n");
/* XGXS control */
wb_data[0] = 0x3c;
@@ -479,6 +520,103 @@
wb_data, 2);
}
+
+ return 0;
+}
+
+static u8 bnx2x_bmac2_enable(struct link_params *params,
+ struct link_vars *vars,
+ u8 is_lb)
+{
+ struct bnx2x *bp = params->bp;
+ u8 port = params->port;
+ u32 bmac_addr = port ? NIG_REG_INGRESS_BMAC1_MEM :
+ NIG_REG_INGRESS_BMAC0_MEM;
+ u32 wb_data[2];
+
+ DP(NETIF_MSG_LINK, "Enabling BigMAC2\n");
+
+ wb_data[0] = 0;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+ udelay(30);
+
+ /* XGXS control: Reset phy HW, MDIO registers, PHY PLL and BMAC */
+ wb_data[0] = 0x3c;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr +
+ BIGMAC2_REGISTER_BMAC_XGXS_CONTROL,
+ wb_data, 2);
+
+ udelay(30);
+
+ /* tx MAC SA */
+ wb_data[0] = ((params->mac_addr[2] << 24) |
+ (params->mac_addr[3] << 16) |
+ (params->mac_addr[4] << 8) |
+ params->mac_addr[5]);
+ wb_data[1] = ((params->mac_addr[0] << 8) |
+ params->mac_addr[1]);
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_SOURCE_ADDR,
+ wb_data, 2);
+
+ udelay(30);
+
+ /* Configure SAFC */
+ wb_data[0] = 0x1000200;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_LLFC_MSG_FLDS,
+ wb_data, 2);
+ udelay(30);
+
+ /* set rx mtu */
+ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_RX_MAX_SIZE,
+ wb_data, 2);
+ udelay(30);
+
+ /* set tx mtu */
+ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_TX_MAX_SIZE,
+ wb_data, 2);
+ udelay(30);
+ /* set cnt max size */
+ wb_data[0] = ETH_MAX_JUMBO_PACKET_SIZE + ETH_OVREHEAD - 2;
+ wb_data[1] = 0;
+ REG_WR_DMAE(bp, bmac_addr + BIGMAC2_REGISTER_CNT_MAX_SIZE,
+ wb_data, 2);
+ udelay(30);
+ bnx2x_update_bmac2(params, vars, is_lb);
+
+ return 0;
+}
+
+u8 bnx2x_bmac_enable(struct link_params *params,
+ struct link_vars *vars,
+ u8 is_lb)
+{
+ u8 rc, port = params->port;
+ struct bnx2x *bp = params->bp;
+ u32 val;
+ /* reset and unreset the BigMac */
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+ udelay(10);
+
+ REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET,
+ (MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port));
+
+ /* enable access for bmac registers */
+ REG_WR(bp, NIG_REG_BMAC0_REGS_OUT_EN + port*4, 0x1);
+
+ /* Enable BMAC according to BMAC type*/
+ if (CHIP_IS_E2(bp))
+ rc = bnx2x_bmac2_enable(params, vars, is_lb);
+ else
+ rc = bnx2x_bmac1_enable(params, vars, is_lb);
REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 0x1);
REG_WR(bp, NIG_REG_XGXS_LANE_SEL_P0 + port*4, 0x0);
REG_WR(bp, NIG_REG_EGRESS_EMAC0_PORT + port*4, 0x0);
@@ -493,7 +631,7 @@
REG_WR(bp, NIG_REG_BMAC0_OUT_EN + port*4, 0x1);
vars->mac_type = MAC_TYPE_BMAC;
- return 0;
+ return rc;
}
@@ -519,13 +657,25 @@
(MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port) &&
nig_bmac_enable) {
- /* Clear Rx Enable bit in BMAC_CONTROL register */
- REG_RD_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
- wb_data, 2);
- wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
- REG_WR_DMAE(bp, bmac_addr + BIGMAC_REGISTER_BMAC_CONTROL,
- wb_data, 2);
-
+ if (CHIP_IS_E2(bp)) {
+ /* Clear Rx Enable bit in BMAC_CONTROL register */
+ REG_RD_DMAE(bp, bmac_addr +
+ BIGMAC2_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+ wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
+ REG_WR_DMAE(bp, bmac_addr +
+ BIGMAC2_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+ } else {
+ /* Clear Rx Enable bit in BMAC_CONTROL register */
+ REG_RD_DMAE(bp, bmac_addr +
+ BIGMAC_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+ wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE;
+ REG_WR_DMAE(bp, bmac_addr +
+ BIGMAC_REGISTER_BMAC_CONTROL,
+ wb_data, 2);
+ }
msleep(1);
}
}
@@ -821,23 +971,31 @@
return -EINVAL;
}
-static void bnx2x_set_aer_mmd(struct link_params *params,
- struct bnx2x_phy *phy)
+static void bnx2x_set_aer_mmd_xgxs(struct link_params *params,
+ struct bnx2x_phy *phy)
{
- struct bnx2x *bp = params->bp;
u32 ser_lane;
- u16 offset;
-
+ u16 offset, aer_val;
+ struct bnx2x *bp = params->bp;
ser_lane = ((params->lane_config &
PORT_HW_CFG_LANE_SWAP_CFG_MASTER_MASK) >>
PORT_HW_CFG_LANE_SWAP_CFG_MASTER_SHIFT);
- offset = (phy->type == PORT_HW_CFG_XGXS_EXT_PHY_TYPE_DIRECT) ?
- (phy->addr + ser_lane) : 0;
-
+ offset = phy->addr + ser_lane;
+ if (CHIP_IS_E2(bp))
+ aer_val = 0x2800 + offset - 1;
+ else
+ aer_val = 0x3800 + offset;
CL45_WR_OVER_CL22(bp, phy,
- MDIO_REG_BANK_AER_BLOCK,
- MDIO_AER_BLOCK_AER_REG, 0x3800 + offset);
+ MDIO_REG_BANK_AER_BLOCK,
+ MDIO_AER_BLOCK_AER_REG, aer_val);
+}
+static void bnx2x_set_aer_mmd_serdes(struct bnx2x *bp,
+ struct bnx2x_phy *phy)
+{
+ CL45_WR_OVER_CL22(bp, phy,
+ MDIO_REG_BANK_AER_BLOCK,
+ MDIO_AER_BLOCK_AER_REG, 0x3800);
}
/******************************************************************/
@@ -2046,12 +2204,12 @@
u8 rc;
vars->phy_flags |= PHY_SGMII_FLAG;
bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
- bnx2x_set_aer_mmd(params, phy);
+ bnx2x_set_aer_mmd_serdes(params->bp, phy);
rc = bnx2x_reset_unicore(params, phy, 1);
/* reset the SerDes and wait for reset bit return low */
if (rc != 0)
return rc;
- bnx2x_set_aer_mmd(params, phy);
+ bnx2x_set_aer_mmd_serdes(params->bp, phy);
return rc;
}
@@ -2076,7 +2234,7 @@
vars->phy_flags &= ~PHY_SGMII_FLAG;
bnx2x_calc_ieee_aneg_adv(phy, params, &vars->ieee_fc);
- bnx2x_set_aer_mmd(params, phy);
+ bnx2x_set_aer_mmd_xgxs(params, phy);
bnx2x_set_master_ln(params, phy);
rc = bnx2x_reset_unicore(params, phy, 0);
@@ -2084,7 +2242,7 @@
if (rc != 0)
return rc;
- bnx2x_set_aer_mmd(params, phy);
+ bnx2x_set_aer_mmd_xgxs(params, phy);
/* setting the masterLn_def again after the reset */
bnx2x_set_master_ln(params, phy);
@@ -2358,7 +2516,7 @@
0x6041);
msleep(200);
/* set aer mmd back */
- bnx2x_set_aer_mmd(params, phy);
+ bnx2x_set_aer_mmd_xgxs(params, phy);
/* and md_devad */
REG_WR(bp, NIG_REG_XGXS0_CTRL_MD_DEVAD + port*0x18,
@@ -2721,7 +2879,10 @@
struct bnx2x *bp = params->bp;
u8 gpio_port;
/* HW reset */
- gpio_port = params->port;
+ if (CHIP_IS_E2(bp))
+ gpio_port = BP_PATH(bp);
+ else
+ gpio_port = params->port;
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
MISC_REGISTERS_GPIO_OUTPUT_LOW,
gpio_port);
@@ -2799,8 +2960,9 @@
}
/* PBF - link up */
- rc |= bnx2x_pbf_update(params, vars->flow_ctrl,
- vars->line_speed);
+ if (!(CHIP_IS_E2(bp)))
+ rc |= bnx2x_pbf_update(params, vars->flow_ctrl,
+ vars->line_speed);
/* disable drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + port*4, 0);
@@ -3443,7 +3605,10 @@
u8 gpio_port;
DP(NETIF_MSG_LINK, "Init 8073\n");
- gpio_port = params->port;
+ if (CHIP_IS_E2(bp))
+ gpio_port = BP_PATH(bp);
+ else
+ gpio_port = params->port;
/* Restore normal power mode*/
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
MISC_REGISTERS_GPIO_OUTPUT_HIGH, gpio_port);
@@ -3680,7 +3845,10 @@
{
struct bnx2x *bp = params->bp;
u8 gpio_port;
- gpio_port = params->port;
+ if (CHIP_IS_E2(bp))
+ gpio_port = BP_PATH(bp);
+ else
+ gpio_port = params->port;
DP(NETIF_MSG_LINK, "Setting 8073 port %d into low power mode\n",
gpio_port);
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
@@ -6371,7 +6539,10 @@
phy->mdio_ctrl = bnx2x_get_emac_base(bp,
SHARED_HW_CFG_MDC_MDIO_ACCESS1_BOTH,
port);
- phy->def_md_devad = DEFAULT_PHY_DEV_ADDR;
+ if (CHIP_IS_E2(bp))
+ phy->def_md_devad = E2_DEFAULT_PHY_DEV_ADDR;
+ else
+ phy->def_md_devad = DEFAULT_PHY_DEV_ADDR;
DP(NETIF_MSG_LINK, "Internal phy port=%d, addr=0x%x, mdio_ctl=0x%x\n",
port, phy->addr, phy->mdio_ctrl);
@@ -6742,7 +6913,9 @@
}
bnx2x_emac_enable(params, vars, 0);
- bnx2x_pbf_update(params, vars->flow_ctrl, vars->line_speed);
+ if (!(CHIP_IS_E2(bp)))
+ bnx2x_pbf_update(params, vars->flow_ctrl,
+ vars->line_speed);
/* disable drain */
REG_WR(bp, NIG_REG_EGRESS_DRAIN0_MODE + params->port*4, 0);
@@ -6932,18 +7105,34 @@
/****************************************************************************/
/* Common function */
/****************************************************************************/
-static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp, u32 shmem_base, u32 shmem2_base, u8 phy_index)
+static u8 bnx2x_8073_common_init_phy(struct bnx2x *bp,
+ u32 shmem_base_path[],
+ u32 shmem2_base_path[], u8 phy_index,
+ u32 chip_id)
{
struct bnx2x_phy phy[PORT_MAX];
struct bnx2x_phy *phy_blk[PORT_MAX];
u16 val;
s8 port;
+ s8 port_of_path = 0;
/* PART1 - Reset both phys */
for (port = PORT_MAX - 1; port >= PORT_0; port--) {
+ u32 shmem_base, shmem2_base;
+ /* In E2, same phy is using for port0 of the two paths */
+ if (CHIP_IS_E2(bp)) {
+ shmem_base = shmem_base_path[port];
+ shmem2_base = shmem2_base_path[port];
+ port_of_path = 0;
+ } else {
+ shmem_base = shmem_base_path[0];
+ shmem2_base = shmem2_base_path[0];
+ port_of_path = port;
+ }
+
/* Extract the ext phy address for the port */
if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
- port, &phy[port]) !=
+ port_of_path, &phy[port]) !=
0) {
DP(NETIF_MSG_LINK, "populate_phy failed\n");
return -EINVAL;
@@ -6981,9 +7170,15 @@
/* PART2 - Download firmware to both phys */
for (port = PORT_MAX - 1; port >= PORT_0; port--) {
u16 fw_ver1;
+ if (CHIP_IS_E2(bp))
+ port_of_path = 0;
+ else
+ port_of_path = port;
+ DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n",
+ phy_blk[port]->addr);
bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port],
- port);
+ port_of_path);
bnx2x_cl45_read(bp, phy_blk[port],
MDIO_PMA_DEVAD,
@@ -7039,9 +7234,10 @@
}
return 0;
}
-
-static u8 bnx2x_8726_common_init_phy(struct bnx2x *bp, u32 shmem_base,
- u32 shmem2_base, u8 phy_index)
+static u8 bnx2x_8726_common_init_phy(struct bnx2x *bp,
+ u32 shmem_base_path[],
+ u32 shmem2_base_path[], u8 phy_index,
+ u32 chip_id)
{
u32 val;
s8 port;
@@ -7056,6 +7252,16 @@
bnx2x_ext_phy_hw_reset(bp, 1);
msleep(5);
for (port = 0; port < PORT_MAX; port++) {
+ u32 shmem_base, shmem2_base;
+
+ /* In E2, same phy is using for port0 of the two paths */
+ if (CHIP_IS_E2(bp)) {
+ shmem_base = shmem_base_path[port];
+ shmem2_base = shmem2_base_path[port];
+ } else {
+ shmem_base = shmem_base_path[0];
+ shmem2_base = shmem2_base_path[0];
+ }
/* Extract the ext phy address for the port */
if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
port, &phy) !=
@@ -7077,14 +7283,16 @@
return 0;
}
-static u8 bnx2x_8727_common_init_phy(struct bnx2x *bp, u32 shmem_base,
- u32 shmem2_base, u8 phy_index)
+static u8 bnx2x_8727_common_init_phy(struct bnx2x *bp,
+ u32 shmem_base_path[],
+ u32 shmem2_base_path[], u8 phy_index,
+ u32 chip_id)
{
s8 port;
u32 swap_val, swap_override;
struct bnx2x_phy phy[PORT_MAX];
struct bnx2x_phy *phy_blk[PORT_MAX];
- DP(NETIF_MSG_LINK, "Executing BCM8727 common init\n");
+ s8 port_of_path;
swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
@@ -7099,19 +7307,33 @@
/* PART1 - Reset both phys */
for (port = PORT_MAX - 1; port >= PORT_0; port--) {
+ u32 shmem_base, shmem2_base;
+
+ /* In E2, same phy is using for port0 of the two paths */
+ if (CHIP_IS_E2(bp)) {
+ shmem_base = shmem_base_path[port];
+ shmem2_base = shmem2_base_path[port];
+ port_of_path = 0;
+ } else {
+ shmem_base = shmem_base_path[0];
+ shmem2_base = shmem2_base_path[0];
+ port_of_path = port;
+ }
+
/* Extract the ext phy address for the port */
if (bnx2x_populate_phy(bp, phy_index, shmem_base, shmem2_base,
- port, &phy[port]) !=
+ port_of_path, &phy[port]) !=
0) {
DP(NETIF_MSG_LINK, "populate phy failed\n");
return -EINVAL;
}
/* disable attentions */
- bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4,
- (NIG_MASK_XGXS0_LINK_STATUS |
- NIG_MASK_XGXS0_LINK10G |
- NIG_MASK_SERDES0_LINK_STATUS |
- NIG_MASK_MI_INT));
+ bnx2x_bits_dis(bp, NIG_REG_MASK_INTERRUPT_PORT0 +
+ port_of_path*4,
+ (NIG_MASK_XGXS0_LINK_STATUS |
+ NIG_MASK_XGXS0_LINK10G |
+ NIG_MASK_SERDES0_LINK_STATUS |
+ NIG_MASK_MI_INT));
/* Reset the phy */
@@ -7133,9 +7355,14 @@
/* PART2 - Download firmware to both phys */
for (port = PORT_MAX - 1; port >= PORT_0; port--) {
u16 fw_ver1;
-
+ if (CHIP_IS_E2(bp))
+ port_of_path = 0;
+ else
+ port_of_path = port;
+ DP(NETIF_MSG_LINK, "Loading spirom for phy address 0x%x\n",
+ phy_blk[port]->addr);
bnx2x_8073_8727_external_rom_boot(bp, phy_blk[port],
- port);
+ port_of_path);
bnx2x_cl45_read(bp, phy_blk[port],
MDIO_PMA_DEVAD,
MDIO_PMA_REG_ROM_VER1, &fw_ver1);
@@ -7151,29 +7378,32 @@
return 0;
}
-static u8 bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base,
- u32 shmem2_base, u8 phy_index,
- u32 ext_phy_type)
+static u8 bnx2x_ext_phy_common_init(struct bnx2x *bp, u32 shmem_base_path[],
+ u32 shmem2_base_path[], u8 phy_index,
+ u32 ext_phy_type, u32 chip_id)
{
u8 rc = 0;
switch (ext_phy_type) {
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
- rc = bnx2x_8073_common_init_phy(bp, shmem_base,
- shmem2_base, phy_index);
+ rc = bnx2x_8073_common_init_phy(bp, shmem_base_path,
+ shmem2_base_path,
+ phy_index, chip_id);
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC:
- rc = bnx2x_8727_common_init_phy(bp, shmem_base,
- shmem2_base, phy_index);
+ rc = bnx2x_8727_common_init_phy(bp, shmem_base_path,
+ shmem2_base_path,
+ phy_index, chip_id);
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
/* GPIO1 affects both ports, so there's need to pull
it for single port alone */
- rc = bnx2x_8726_common_init_phy(bp, shmem_base,
- shmem2_base, phy_index);
+ rc = bnx2x_8726_common_init_phy(bp, shmem_base_path,
+ shmem2_base_path,
+ phy_index, chip_id);
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE:
rc = -EINVAL;
@@ -7188,8 +7418,8 @@
return rc;
}
-u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base,
- u32 shmem2_base)
+u8 bnx2x_common_init_phy(struct bnx2x *bp, u32 shmem_base_path[],
+ u32 shmem2_base_path[], u32 chip_id)
{
u8 rc = 0;
u8 phy_index;
@@ -7203,12 +7433,13 @@
for (phy_index = EXT_PHY1; phy_index < MAX_PHYS;
phy_index++) {
ext_phy_config = bnx2x_get_ext_phy_config(bp,
- shmem_base,
+ shmem_base_path[0],
phy_index, 0);
ext_phy_type = XGXS_EXT_PHY_TYPE(ext_phy_config);
- rc |= bnx2x_ext_phy_common_init(bp, shmem_base,
- shmem2_base,
- phy_index, ext_phy_type);
+ rc |= bnx2x_ext_phy_common_init(bp, shmem_base_path,
+ shmem2_base_path,
+ phy_index, ext_phy_type,
+ chip_id);
}
return rc;
}