bnx2x: Changing the Disabled state to a flag
When working with DCC, a function can be disabled or enabled (virtual link down
or up). Using the function state introduced some race conditions with the
load/unload flow.
Using a separate flag to indicate that the function is disabled.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/bnx2x.h b/drivers/net/bnx2x.h
index 60fa14f..185a6ba 100644
--- a/drivers/net/bnx2x.h
+++ b/drivers/net/bnx2x.h
@@ -900,6 +900,7 @@
#define BP_NOMCP(bp) (bp->flags & NO_MCP_FLAG)
#define HW_VLAN_TX_FLAG 0x400
#define HW_VLAN_RX_FLAG 0x800
+#define MF_FUNC_DIS 0x1000
int func;
#define BP_PORT(bp) (bp->func % PORT_MAX)
@@ -965,7 +966,6 @@
#define BNX2X_STATE_CLOSING_WAIT4_HALT 0x4000
#define BNX2X_STATE_CLOSING_WAIT4_DELETE 0x5000
#define BNX2X_STATE_CLOSING_WAIT4_UNLOAD 0x6000
-#define BNX2X_STATE_DISABLED 0xd000
#define BNX2X_STATE_DIAG 0xe000
#define BNX2X_STATE_ERROR 0xf000
diff --git a/drivers/net/bnx2x_main.c b/drivers/net/bnx2x_main.c
index 691cf15..e7b3b27d 100644
--- a/drivers/net/bnx2x_main.c
+++ b/drivers/net/bnx2x_main.c
@@ -1043,7 +1043,6 @@
break;
case (RAMROD_CMD_ID_ETH_SET_MAC | BNX2X_STATE_CLOSING_WAIT4_HALT):
- case (RAMROD_CMD_ID_ETH_SET_MAC | BNX2X_STATE_DISABLED):
DP(NETIF_MSG_IFDOWN, "got (un)set mac ramrod\n");
bp->set_mac_pending--;
smp_wmb();
@@ -2157,7 +2156,7 @@
static void bnx2x_link_report(struct bnx2x *bp)
{
- if (bp->state == BNX2X_STATE_DISABLED) {
+ if (bp->flags & MF_FUNC_DIS) {
netif_carrier_off(bp->dev);
printk(KERN_ERR PFX "%s NIC Link is Down\n", bp->dev->name);
return;
@@ -2437,8 +2436,7 @@
memset(&(pstats->mac_stx[0]), 0,
sizeof(struct mac_stx));
}
- if ((bp->state == BNX2X_STATE_OPEN) ||
- (bp->state == BNX2X_STATE_DISABLED))
+ if (bp->state == BNX2X_STATE_OPEN)
bnx2x_stats_handle(bp, STATS_EVENT_LINK_UP);
}
@@ -2481,9 +2479,7 @@
static void bnx2x__link_status_update(struct bnx2x *bp)
{
- int func = BP_FUNC(bp);
-
- if (bp->state != BNX2X_STATE_OPEN)
+ if ((bp->state != BNX2X_STATE_OPEN) || (bp->flags & MF_FUNC_DIS))
return;
bnx2x_link_status_update(&bp->link_params, &bp->link_vars);
@@ -2640,14 +2636,19 @@
if (dcc_event & DRV_STATUS_DCC_DISABLE_ENABLE_PF) {
+ /*
+ * This is the only place besides the function initialization
+ * where the bp->flags can change so it is done without any
+ * locks
+ */
if (bp->mf_config & FUNC_MF_CFG_FUNC_DISABLED) {
DP(NETIF_MSG_IFDOWN, "mf_cfg function disabled\n");
- bp->state = BNX2X_STATE_DISABLED;
+ bp->flags |= MF_FUNC_DIS;
bnx2x_e1h_disable(bp);
} else {
DP(NETIF_MSG_IFUP, "mf_cfg function enabled\n");
- bp->state = BNX2X_STATE_OPEN;
+ bp->flags &= ~MF_FUNC_DIS;
bnx2x_e1h_enable(bp);
}
@@ -4695,8 +4696,7 @@
}
}
- if ((bp->state == BNX2X_STATE_OPEN) ||
- (bp->state == BNX2X_STATE_DISABLED))
+ if (bp->state == BNX2X_STATE_OPEN)
bnx2x_stats_handle(bp, STATS_EVENT_UPDATE);
timer_restart:
@@ -7629,7 +7629,7 @@
if (CHIP_IS_E1H(bp))
if (bp->mf_config & FUNC_MF_CFG_FUNC_DISABLED) {
DP(NETIF_MSG_IFUP, "mf_cfg function disabled\n");
- bp->state = BNX2X_STATE_DISABLED;
+ bp->flags |= MF_FUNC_DIS;
}
if (bp->state == BNX2X_STATE_OPEN) {
@@ -9034,7 +9034,9 @@
cmd->supported = bp->port.supported;
cmd->advertising = bp->port.advertising;
- if (netif_carrier_ok(dev)) {
+ if ((bp->state == BNX2X_STATE_OPEN) &&
+ !(bp->flags & MF_FUNC_DIS) &&
+ (bp->link_vars.link_up)) {
cmd->speed = bp->link_vars.line_speed;
cmd->duplex = bp->link_vars.duplex;
if (IS_E1HMF(bp)) {
@@ -9433,6 +9435,9 @@
{
struct bnx2x *bp = netdev_priv(dev);
+ if (bp->flags & MF_FUNC_DIS)
+ return 0;
+
return bp->link_vars.link_up;
}
@@ -9837,8 +9842,7 @@
} else if (eeprom->magic == 0x50485952) {
/* 'PHYR' (0x50485952): re-init link after FW upgrade */
- if ((bp->state == BNX2X_STATE_OPEN) ||
- (bp->state == BNX2X_STATE_DISABLED)) {
+ if (bp->state == BNX2X_STATE_OPEN) {
bnx2x_acquire_phy_lock(bp);
rc |= bnx2x_link_reset(&bp->link_params,
&bp->link_vars, 1);