MIPS: Netlogic: Platform changes for XLS USB
Add USB initialization code, setup resources and add USB platform
driver in mips/netlogic/xlr/platform.c.
Add USB support for XLR/XLS platform in Kconfig.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index b3e10fd..96bad98 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -787,6 +787,8 @@
select ZONE_DMA if 64BIT
select SYNC_R4K
select SYS_HAS_EARLY_PRINTK
+ select USB_ARCH_HAS_OHCI if USB_SUPPORT
+ select USB_ARCH_HAS_EHCI if USB_SUPPORT
help
Support for systems based on Netlogic XLR and XLS processors.
Say Y here if you have a XLR or XLS based board.
diff --git a/arch/mips/netlogic/xlr/platform.c b/arch/mips/netlogic/xlr/platform.c
index eab64b4..cb0ab63 100644
--- a/arch/mips/netlogic/xlr/platform.c
+++ b/arch/mips/netlogic/xlr/platform.c
@@ -97,3 +97,92 @@
}
arch_initcall(nlm_uart_init);
+
+#ifdef CONFIG_USB
+/* Platform USB devices, only on XLS chips */
+static u64 xls_usb_dmamask = ~(u32)0;
+#define USB_PLATFORM_DEV(n, i, irq) \
+ { \
+ .name = n, \
+ .id = i, \
+ .num_resources = 2, \
+ .dev = { \
+ .dma_mask = &xls_usb_dmamask, \
+ .coherent_dma_mask = 0xffffffff, \
+ }, \
+ .resource = (struct resource[]) { \
+ { \
+ .flags = IORESOURCE_MEM, \
+ }, \
+ { \
+ .start = irq, \
+ .end = irq, \
+ .flags = IORESOURCE_IRQ, \
+ }, \
+ }, \
+ }
+
+static struct platform_device xls_usb_ehci_device =
+ USB_PLATFORM_DEV("ehci-xls", 0, PIC_USB_IRQ);
+static struct platform_device xls_usb_ohci_device_0 =
+ USB_PLATFORM_DEV("ohci-xls-0", 1, PIC_USB_IRQ);
+static struct platform_device xls_usb_ohci_device_1 =
+ USB_PLATFORM_DEV("ohci-xls-1", 2, PIC_USB_IRQ);
+
+static struct platform_device *xls_platform_devices[] = {
+ &xls_usb_ehci_device,
+ &xls_usb_ohci_device_0,
+ &xls_usb_ohci_device_1,
+};
+
+int xls_platform_usb_init(void)
+{
+ uint64_t usb_mmio, gpio_mmio;
+ unsigned long memres;
+ uint32_t val;
+
+ if (!nlm_chip_is_xls())
+ return 0;
+
+ gpio_mmio = nlm_mmio_base(NETLOGIC_IO_GPIO_OFFSET);
+ usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_1_OFFSET);
+
+ /* Clear Rogue Phy INTs */
+ nlm_write_reg(usb_mmio, 49, 0x10000000);
+ /* Enable all interrupts */
+ nlm_write_reg(usb_mmio, 50, 0x1f000000);
+
+ /* Enable ports */
+ nlm_write_reg(usb_mmio, 1, 0x07000500);
+
+ val = nlm_read_reg(gpio_mmio, 21);
+ if (((val >> 22) & 0x01) == 0) {
+ pr_info("Detected USB Device mode - Not supported!\n");
+ nlm_write_reg(usb_mmio, 0, 0x01000000);
+ return 0;
+ }
+
+ pr_info("Detected USB Host mode - Adding XLS USB devices.\n");
+ /* Clear reset, host mode */
+ nlm_write_reg(usb_mmio, 0, 0x02000000);
+
+ /* Memory resource for various XLS usb ports */
+ usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_0_OFFSET);
+ memres = CPHYSADDR((unsigned long)usb_mmio);
+ xls_usb_ehci_device.resource[0].start = memres;
+ xls_usb_ehci_device.resource[0].end = memres + 0x400 - 1;
+
+ memres += 0x400;
+ xls_usb_ohci_device_0.resource[0].start = memres;
+ xls_usb_ohci_device_0.resource[0].end = memres + 0x400 - 1;
+
+ memres += 0x400;
+ xls_usb_ohci_device_1.resource[0].start = memres;
+ xls_usb_ohci_device_1.resource[0].end = memres + 0x400 - 1;
+
+ return platform_add_devices(xls_platform_devices,
+ ARRAY_SIZE(xls_platform_devices));
+}
+
+arch_initcall(xls_platform_usb_init);
+#endif