Merge 3.10-rc3 into char-misc-next
We want the changes in here.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt
new file mode 100644
index 0000000..653c90c
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/mvebu-devbus.txt
@@ -0,0 +1,156 @@
+Device tree bindings for MVEBU Device Bus controllers
+
+The Device Bus controller available in some Marvell's SoC allows to control
+different types of standard memory and I/O devices such as NOR, NAND, and FPGA.
+The actual devices are instantiated from the child nodes of a Device Bus node.
+
+Required properties:
+
+ - compatible: Currently only Armada 370/XP SoC are supported,
+ with this compatible string:
+
+ marvell,mvebu-devbus
+
+ - reg: A resource specifier for the register space.
+ This is the base address of a chip select within
+ the controller's register space.
+ (see the example below)
+
+ - #address-cells: Must be set to 1
+ - #size-cells: Must be set to 1
+ - ranges: Must be set up to reflect the memory layout with four
+ integer values for each chip-select line in use:
+ 0 <physical address of mapping> <size>
+
+Mandatory timing properties for child nodes:
+
+Read parameters:
+
+ - devbus,turn-off-ps: Defines the time during which the controller does not
+ drive the AD bus after the completion of a device read.
+ This prevents contentions on the Device Bus after a read
+ cycle from a slow device.
+
+ - devbus,bus-width: Defines the bus width (e.g. <16>)
+
+ - devbus,badr-skew-ps: Defines the time delay from from A[2:0] toggle,
+ to read data sample. This parameter is useful for
+ synchronous pipelined devices, where the address
+ precedes the read data by one or two cycles.
+
+ - devbus,acc-first-ps: Defines the time delay from the negation of
+ ALE[0] to the cycle that the first read data is sampled
+ by the controller.
+
+ - devbus,acc-next-ps: Defines the time delay between the cycle that
+ samples data N and the cycle that samples data N+1
+ (in burst accesses).
+
+ - devbus,rd-setup-ps: Defines the time delay between DEV_CSn assertion to
+ DEV_OEn assertion. If set to 0 (default),
+ DEV_OEn and DEV_CSn are asserted at the same cycle.
+ This parameter has no affect on <acc-first-ps> parameter
+ (no affect on first data sample). Set <rd-setup-ps>
+ to a value smaller than <acc-first-ps>.
+
+ - devbus,rd-hold-ps: Defines the time between the last data sample to the
+ de-assertion of DEV_CSn. If set to 0 (default),
+ DEV_OEn and DEV_CSn are de-asserted at the same cycle
+ (the cycle of the last data sample).
+ This parameter has no affect on DEV_OEn de-assertion.
+ DEV_OEn is always de-asserted the next cycle after
+ last data sampled. Also this parameter has no
+ affect on <turn-off-ps> parameter.
+ Set <rd-hold-ps> to a value smaller than <turn-off-ps>.
+
+Write parameters:
+
+ - devbus,ale-wr-ps: Defines the time delay from the ALE[0] negation cycle
+ to the DEV_WEn assertion.
+
+ - devbus,wr-low-ps: Defines the time during which DEV_WEn is active.
+ A[2:0] and Data are kept valid as long as DEV_WEn
+ is active. This parameter defines the setup time of
+ address and data to DEV_WEn rise.
+
+ - devbus,wr-high-ps: Defines the time during which DEV_WEn is kept
+ inactive (high) between data beats of a burst write.
+ DEV_A[2:0] and Data are kept valid (do not toggle) for
+ <wr-high-ps> - <tick> ps.
+ This parameter defines the hold time of address and
+ data after DEV_WEn rise.
+
+ - devbus,sync-enable: Synchronous device enable.
+ 1: True
+ 0: False
+
+An example for an Armada XP GP board, with a 16 MiB NOR device as child
+is showed below. Note that the Device Bus driver is in charge of allocating
+the mbus address decoding window for each of its child devices.
+The window is created using the chip select specified in the child
+device node together with the base address and size specified in the ranges
+property. For instance, in the example below the allocated decoding window
+will start at base address 0xf0000000, with a size 0x1000000 (16 MiB)
+for chip select 0 (a.k.a DEV_BOOTCS).
+
+This address window handling is done in this mvebu-devbus only as a temporary
+solution. It will be removed when the support for mbus device tree binding is
+added.
+
+The reg property implicitly specifies the chip select as this:
+
+ 0x10400: DEV_BOOTCS
+ 0x10408: DEV_CS0
+ 0x10410: DEV_CS1
+ 0x10418: DEV_CS2
+ 0x10420: DEV_CS3
+
+Example:
+
+ devbus-bootcs@d0010400 {
+ status = "okay";
+ ranges = <0 0xf0000000 0x1000000>; /* @addr 0xf0000000, size 0x1000000 */
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ flash@0 {
+ compatible = "cfi-flash";
+
+ /* 16 MiB */
+ reg = <0 0x1000000>;
+ bank-width = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * We split the 16 MiB in two partitions,
+ * just as an example.
+ */
+ partition@0 {
+ label = "First";
+ reg = <0 0x800000>;
+ };
+
+ partition@800000 {
+ label = "Second";
+ reg = <0x800000 0x800000>;
+ };
+ };
+ };
diff --git a/drivers/char/mspec.c b/drivers/char/mspec.c
index e1f60f9..f1d7fa4 100644
--- a/drivers/char/mspec.c
+++ b/drivers/char/mspec.c
@@ -267,7 +267,7 @@
if ((vma->vm_flags & VM_WRITE) == 0)
return -EPERM;
- pages = (vma->vm_end - vma->vm_start) >> PAGE_SHIFT;
+ pages = vma_pages(vma);
vdata_size = sizeof(struct vma_data) + pages * sizeof(long);
if (vdata_size <= PAGE_SIZE)
vdata = kzalloc(vdata_size, GFP_KERNEL);
diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
index 067f311..29a11db 100644
--- a/drivers/memory/Kconfig
+++ b/drivers/memory/Kconfig
@@ -20,6 +20,16 @@
parameters and other settings during frequency, voltage and
temperature changes
+config MVEBU_DEVBUS
+ bool "Marvell EBU Device Bus Controller"
+ default y
+ depends on PLAT_ORION && OF
+ help
+ This driver is for the Device Bus controller available in some
+ Marvell EBU SoCs such as Discovery (mv78xx0), Orion (88f5xxx) and
+ Armada 370 and Armada XP. This controller allows to handle flash
+ devices such as NOR, NAND, SRAM, and FPGA.
+
config TEGRA20_MC
bool "Tegra20 Memory Controller(MC) driver"
default y
diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
index 9cce5d7..969d923 100644
--- a/drivers/memory/Makefile
+++ b/drivers/memory/Makefile
@@ -6,5 +6,6 @@
obj-$(CONFIG_OF) += of_memory.o
endif
obj-$(CONFIG_TI_EMIF) += emif.o
+obj-$(CONFIG_MVEBU_DEVBUS) += mvebu-devbus.o
obj-$(CONFIG_TEGRA20_MC) += tegra20-mc.o
obj-$(CONFIG_TEGRA30_MC) += tegra30-mc.o
diff --git a/drivers/memory/mvebu-devbus.c b/drivers/memory/mvebu-devbus.c
new file mode 100644
index 0000000..978e8e3
--- /dev/null
+++ b/drivers/memory/mvebu-devbus.c
@@ -0,0 +1,340 @@
+/*
+ * Marvell EBU SoC Device Bus Controller
+ * (memory controller for NOR/NAND/SRAM/FPGA devices)
+ *
+ * Copyright (C) 2013 Marvell
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/mbus.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+/* Register definitions */
+#define DEV_WIDTH_BIT 30
+#define BADR_SKEW_BIT 28
+#define RD_HOLD_BIT 23
+#define ACC_NEXT_BIT 17
+#define RD_SETUP_BIT 12
+#define ACC_FIRST_BIT 6
+
+#define SYNC_ENABLE_BIT 24
+#define WR_HIGH_BIT 16
+#define WR_LOW_BIT 8
+
+#define READ_PARAM_OFFSET 0x0
+#define WRITE_PARAM_OFFSET 0x4
+
+static const char * const devbus_wins[] = {
+ "devbus-boot",
+ "devbus-cs0",
+ "devbus-cs1",
+ "devbus-cs2",
+ "devbus-cs3",
+};
+
+struct devbus_read_params {
+ u32 bus_width;
+ u32 badr_skew;
+ u32 turn_off;
+ u32 acc_first;
+ u32 acc_next;
+ u32 rd_setup;
+ u32 rd_hold;
+};
+
+struct devbus_write_params {
+ u32 sync_enable;
+ u32 wr_high;
+ u32 wr_low;
+ u32 ale_wr;
+};
+
+struct devbus {
+ struct device *dev;
+ void __iomem *base;
+ unsigned long tick_ps;
+};
+
+static int get_timing_param_ps(struct devbus *devbus,
+ struct device_node *node,
+ const char *name,
+ u32 *ticks)
+{
+ u32 time_ps;
+ int err;
+
+ err = of_property_read_u32(node, name, &time_ps);
+ if (err < 0) {
+ dev_err(devbus->dev, "%s has no '%s' property\n",
+ name, node->full_name);
+ return err;
+ }
+
+ *ticks = (time_ps + devbus->tick_ps - 1) / devbus->tick_ps;
+
+ dev_dbg(devbus->dev, "%s: %u ps -> 0x%x\n",
+ name, time_ps, *ticks);
+ return 0;
+}
+
+static int devbus_set_timing_params(struct devbus *devbus,
+ struct device_node *node)
+{
+ struct devbus_read_params r;
+ struct devbus_write_params w;
+ u32 value;
+ int err;
+
+ dev_dbg(devbus->dev, "Setting timing parameter, tick is %lu ps\n",
+ devbus->tick_ps);
+
+ /* Get read timings */
+ err = of_property_read_u32(node, "devbus,bus-width", &r.bus_width);
+ if (err < 0) {
+ dev_err(devbus->dev,
+ "%s has no 'devbus,bus-width' property\n",
+ node->full_name);
+ return err;
+ }
+ /* Convert bit width to byte width */
+ r.bus_width /= 8;
+
+ err = get_timing_param_ps(devbus, node, "devbus,badr-skew-ps",
+ &r.badr_skew);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,turn-off-ps",
+ &r.turn_off);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,acc-first-ps",
+ &r.acc_first);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,acc-next-ps",
+ &r.acc_next);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,rd-setup-ps",
+ &r.rd_setup);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,rd-hold-ps",
+ &r.rd_hold);
+ if (err < 0)
+ return err;
+
+ /* Get write timings */
+ err = of_property_read_u32(node, "devbus,sync-enable",
+ &w.sync_enable);
+ if (err < 0) {
+ dev_err(devbus->dev,
+ "%s has no 'devbus,sync-enable' property\n",
+ node->full_name);
+ return err;
+ }
+
+ err = get_timing_param_ps(devbus, node, "devbus,ale-wr-ps",
+ &w.ale_wr);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,wr-low-ps",
+ &w.wr_low);
+ if (err < 0)
+ return err;
+
+ err = get_timing_param_ps(devbus, node, "devbus,wr-high-ps",
+ &w.wr_high);
+ if (err < 0)
+ return err;
+
+ /* Set read timings */
+ value = r.bus_width << DEV_WIDTH_BIT |
+ r.badr_skew << BADR_SKEW_BIT |
+ r.rd_hold << RD_HOLD_BIT |
+ r.acc_next << ACC_NEXT_BIT |
+ r.rd_setup << RD_SETUP_BIT |
+ r.acc_first << ACC_FIRST_BIT |
+ r.turn_off;
+
+ dev_dbg(devbus->dev, "read parameters register 0x%p = 0x%x\n",
+ devbus->base + READ_PARAM_OFFSET,
+ value);
+
+ writel(value, devbus->base + READ_PARAM_OFFSET);
+
+ /* Set write timings */
+ value = w.sync_enable << SYNC_ENABLE_BIT |
+ w.wr_low << WR_LOW_BIT |
+ w.wr_high << WR_HIGH_BIT |
+ w.ale_wr;
+
+ dev_dbg(devbus->dev, "write parameters register: 0x%p = 0x%x\n",
+ devbus->base + WRITE_PARAM_OFFSET,
+ value);
+
+ writel(value, devbus->base + WRITE_PARAM_OFFSET);
+
+ return 0;
+}
+
+static int mvebu_devbus_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *node = pdev->dev.of_node;
+ struct device_node *parent;
+ struct devbus *devbus;
+ struct resource *res;
+ struct clk *clk;
+ unsigned long rate;
+ const __be32 *ranges;
+ int err, cs;
+ int addr_cells, p_addr_cells, size_cells;
+ int ranges_len, tuple_len;
+ u32 base, size;
+
+ devbus = devm_kzalloc(&pdev->dev, sizeof(struct devbus), GFP_KERNEL);
+ if (!devbus)
+ return -ENOMEM;
+
+ devbus->dev = dev;
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ devbus->base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(devbus->base))
+ return PTR_ERR(devbus->base);
+
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+ clk_prepare_enable(clk);
+
+ /*
+ * Obtain clock period in picoseconds,
+ * we need this in order to convert timing
+ * parameters from cycles to picoseconds.
+ */
+ rate = clk_get_rate(clk) / 1000;
+ devbus->tick_ps = 1000000000 / rate;
+
+ /* Read the device tree node and set the new timing parameters */
+ err = devbus_set_timing_params(devbus, node);
+ if (err < 0)
+ return err;
+
+ /*
+ * Allocate an address window for this device.
+ * If the device probing fails, then we won't be able to
+ * remove the allocated address decoding window.
+ *
+ * FIXME: This is only a temporary hack! We need to do this here
+ * because we still don't have device tree bindings for mbus.
+ * Once that support is added, we will declare these address windows
+ * statically in the device tree, and remove the window configuration
+ * from here.
+ */
+
+ /*
+ * Get the CS to choose the window string.
+ * This is a bit hacky, but it will be removed once the
+ * address windows are declared in the device tree.
+ */
+ cs = (((unsigned long)devbus->base) % 0x400) / 8;
+
+ /*
+ * Parse 'ranges' property to obtain a (base,size) window tuple.
+ * This will be removed once the address windows
+ * are declared in the device tree.
+ */
+ parent = of_get_parent(node);
+ if (!parent)
+ return -EINVAL;
+
+ p_addr_cells = of_n_addr_cells(parent);
+ of_node_put(parent);
+
+ addr_cells = of_n_addr_cells(node);
+ size_cells = of_n_size_cells(node);
+ tuple_len = (p_addr_cells + addr_cells + size_cells) * sizeof(__be32);
+
+ ranges = of_get_property(node, "ranges", &ranges_len);
+ if (ranges == NULL || ranges_len != tuple_len)
+ return -EINVAL;
+
+ base = of_translate_address(node, ranges + addr_cells);
+ if (base == OF_BAD_ADDR)
+ return -EINVAL;
+ size = of_read_number(ranges + addr_cells + p_addr_cells, size_cells);
+
+ /*
+ * Create an mbus address windows.
+ * FIXME: Remove this, together with the above code, once the
+ * address windows are declared in the device tree.
+ */
+ err = mvebu_mbus_add_window(devbus_wins[cs], base, size);
+ if (err < 0)
+ return err;
+
+ /*
+ * We need to create a child device explicitly from here to
+ * guarantee that the child will be probed after the timing
+ * parameters for the bus are written.
+ */
+ err = of_platform_populate(node, NULL, NULL, dev);
+ if (err < 0) {
+ mvebu_mbus_del_window(base, size);
+ return err;
+ }
+
+ return 0;
+}
+
+static const struct of_device_id mvebu_devbus_of_match[] = {
+ { .compatible = "marvell,mvebu-devbus" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mvebu_devbus_of_match);
+
+static struct platform_driver mvebu_devbus_driver = {
+ .probe = mvebu_devbus_probe,
+ .driver = {
+ .name = "mvebu-devbus",
+ .owner = THIS_MODULE,
+ .of_match_table = mvebu_devbus_of_match,
+ },
+};
+
+static int __init mvebu_devbus_init(void)
+{
+ return platform_driver_register(&mvebu_devbus_driver);
+}
+module_init(mvebu_devbus_init);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Ezequiel Garcia <ezequiel.garcia@free-electrons.com>");
+MODULE_DESCRIPTION("Marvell EBU SoC Device Bus controller");
diff --git a/drivers/misc/arm-charlcd.c b/drivers/misc/arm-charlcd.c
index 48651ef..1256a4b 100644
--- a/drivers/misc/arm-charlcd.c
+++ b/drivers/misc/arm-charlcd.c
@@ -291,7 +291,7 @@
lcd->virtbase = ioremap(lcd->phybase, lcd->physize);
if (!lcd->virtbase) {
ret = -ENOMEM;
- goto out_no_remap;
+ goto out_no_memregion;
}
lcd->irq = platform_get_irq(pdev, 0);
@@ -320,8 +320,6 @@
out_no_irq:
iounmap(lcd->virtbase);
-out_no_remap:
- platform_set_drvdata(pdev, NULL);
out_no_memregion:
release_mem_region(lcd->phybase, SZ_4K);
out_no_resource:
@@ -337,7 +335,6 @@
free_irq(lcd->irq, lcd);
iounmap(lcd->virtbase);
release_mem_region(lcd->phybase, lcd->physize);
- platform_set_drvdata(pdev, NULL);
kfree(lcd);
}
diff --git a/drivers/misc/ep93xx_pwm.c b/drivers/misc/ep93xx_pwm.c
index 96787ec..9ba93f0 100644
--- a/drivers/misc/ep93xx_pwm.c
+++ b/drivers/misc/ep93xx_pwm.c
@@ -347,7 +347,6 @@
ep93xx_pwm_disable(pwm);
clk_disable(pwm->clk);
clk_put(pwm->clk);
- platform_set_drvdata(pdev, NULL);
sysfs_remove_group(&pdev->dev.kobj, &ep93xx_pwm_sysfs_files);
iounmap(pwm->mmio_base);
release_mem_region(res->start, resource_size(res));
diff --git a/drivers/misc/mei/amthif.c b/drivers/misc/mei/amthif.c
index b3e5098..749452f 100644
--- a/drivers/misc/mei/amthif.c
+++ b/drivers/misc/mei/amthif.c
@@ -443,11 +443,11 @@
*
* returns 0, OK; otherwise, error.
*/
-int mei_amthif_irq_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list)
+int mei_amthif_irq_write_complete(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
struct mei_msg_hdr mei_hdr;
- struct mei_cl *cl = cb->cl;
size_t len = dev->iamthif_msg_buf_size - dev->iamthif_msg_buf_index;
u32 msg_slots = mei_data2slots(len);
diff --git a/drivers/misc/mei/client.c b/drivers/misc/mei/client.c
index e310ca6..c2534ca 100644
--- a/drivers/misc/mei/client.c
+++ b/drivers/misc/mei/client.c
@@ -785,6 +785,32 @@
}
+/**
+ * mei_cl_complete - processes completed operation for a client
+ *
+ * @cl: private data of the file object.
+ * @cb: callback block.
+ */
+void mei_cl_complete(struct mei_cl *cl, struct mei_cl_cb *cb)
+{
+ if (cb->fop_type == MEI_FOP_WRITE) {
+ mei_io_cb_free(cb);
+ cb = NULL;
+ cl->writing_state = MEI_WRITE_COMPLETE;
+ if (waitqueue_active(&cl->tx_wait))
+ wake_up_interruptible(&cl->tx_wait);
+
+ } else if (cb->fop_type == MEI_FOP_READ &&
+ MEI_READING == cl->reading_state) {
+ cl->reading_state = MEI_READ_COMPLETE;
+ if (waitqueue_active(&cl->rx_wait))
+ wake_up_interruptible(&cl->rx_wait);
+ else
+ mei_cl_bus_rx_event(cl);
+
+ }
+}
+
/**
* mei_cl_all_disconnect - disconnect forcefully all connected clients
diff --git a/drivers/misc/mei/client.h b/drivers/misc/mei/client.h
index cfdb144..7dc2af7 100644
--- a/drivers/misc/mei/client.h
+++ b/drivers/misc/mei/client.h
@@ -89,6 +89,7 @@
int mei_cl_connect(struct mei_cl *cl, struct file *file);
int mei_cl_read_start(struct mei_cl *cl, size_t length);
int mei_cl_write(struct mei_cl *cl, struct mei_cl_cb *cb, bool blocking);
+void mei_cl_complete(struct mei_cl *cl, struct mei_cl_cb *cb);
void mei_host_client_init(struct work_struct *work);
diff --git a/drivers/misc/mei/interrupt.c b/drivers/misc/mei/interrupt.c
index 2ad7369..7d9509a 100644
--- a/drivers/misc/mei/interrupt.c
+++ b/drivers/misc/mei/interrupt.c
@@ -31,32 +31,6 @@
/**
- * mei_cl_complete_handler - processes completed operation for a client
- *
- * @cl: private data of the file object.
- * @cb: callback block.
- */
-static void mei_cl_complete_handler(struct mei_cl *cl, struct mei_cl_cb *cb)
-{
- if (cb->fop_type == MEI_FOP_WRITE) {
- mei_io_cb_free(cb);
- cb = NULL;
- cl->writing_state = MEI_WRITE_COMPLETE;
- if (waitqueue_active(&cl->tx_wait))
- wake_up_interruptible(&cl->tx_wait);
-
- } else if (cb->fop_type == MEI_FOP_READ &&
- MEI_READING == cl->reading_state) {
- cl->reading_state = MEI_READ_COMPLETE;
- if (waitqueue_active(&cl->rx_wait))
- wake_up_interruptible(&cl->rx_wait);
- else
- mei_cl_bus_rx_event(cl);
-
- }
-}
-
-/**
* mei_irq_compl_handler - dispatch complete handelers
* for the completed callbacks
*
@@ -78,7 +52,7 @@
if (cl == &dev->iamthif_cl)
mei_amthif_complete(dev, cb);
else
- mei_cl_complete_handler(cl, cb);
+ mei_cl_complete(cl, cb);
}
}
EXPORT_SYMBOL_GPL(mei_irq_compl_handler);
@@ -189,21 +163,21 @@
}
/**
- * _mei_irq_thread_close - processes close related operation.
+ * mei_cl_irq_close - processes close related operation from
+ * interrupt thread context - send disconnect request
*
- * @dev: the device structure.
+ * @cl: client
+ * @cb: callback block.
* @slots: free slots.
- * @cb_pos: callback block.
- * @cl: private data of the file object.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int _mei_irq_thread_close(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb_pos,
- struct mei_cl *cl,
- struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_close(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
+
u32 msg_slots =
mei_data2slots(sizeof(struct hbm_client_connect_request));
@@ -214,15 +188,15 @@
if (mei_hbm_cl_disconnect_req(dev, cl)) {
cl->status = 0;
- cb_pos->buf_idx = 0;
- list_move_tail(&cb_pos->list, &cmpl_list->list);
+ cb->buf_idx = 0;
+ list_move_tail(&cb->list, &cmpl_list->list);
return -EIO;
}
cl->state = MEI_FILE_DISCONNECTING;
cl->status = 0;
- cb_pos->buf_idx = 0;
- list_move_tail(&cb_pos->list, &dev->ctrl_rd_list.list);
+ cb->buf_idx = 0;
+ list_move_tail(&cb->list, &dev->ctrl_rd_list.list);
cl->timer_count = MEI_CONNECT_TIMEOUT;
return 0;
@@ -230,26 +204,26 @@
/**
- * _mei_irq_thread_read - processes read related operation.
+ * mei_cl_irq_close - processes client read related operation from the
+ * interrupt thread context - request for flow control credits
*
- * @dev: the device structure.
+ * @cl: client
+ * @cb: callback block.
* @slots: free slots.
- * @cb_pos: callback block.
- * @cl: private data of the file object.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int _mei_irq_thread_read(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb_pos,
- struct mei_cl *cl,
- struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_read(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
+
u32 msg_slots = mei_data2slots(sizeof(struct hbm_flow_control));
if (*slots < msg_slots) {
/* return the cancel routine */
- list_del(&cb_pos->list);
+ list_del(&cb->list);
return -EMSGSIZE;
}
@@ -257,38 +231,38 @@
if (mei_hbm_cl_flow_control_req(dev, cl)) {
cl->status = -ENODEV;
- cb_pos->buf_idx = 0;
- list_move_tail(&cb_pos->list, &cmpl_list->list);
+ cb->buf_idx = 0;
+ list_move_tail(&cb->list, &cmpl_list->list);
return -ENODEV;
}
- list_move_tail(&cb_pos->list, &dev->read_list.list);
+ list_move_tail(&cb->list, &dev->read_list.list);
return 0;
}
/**
- * _mei_irq_thread_ioctl - processes ioctl related operation.
+ * mei_cl_irq_ioctl - processes client ioctl related operation from the
+ * interrupt thread context - send connection request
*
- * @dev: the device structure.
+ * @cl: client
+ * @cb: callback block.
* @slots: free slots.
- * @cb_pos: callback block.
- * @cl: private data of the file object.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int _mei_irq_thread_ioctl(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb_pos,
- struct mei_cl *cl,
- struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_ioctl(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
+
u32 msg_slots =
mei_data2slots(sizeof(struct hbm_client_connect_request));
if (*slots < msg_slots) {
/* return the cancel routine */
- list_del(&cb_pos->list);
+ list_del(&cb->list);
return -EMSGSIZE;
}
@@ -298,31 +272,31 @@
if (mei_hbm_cl_connect_req(dev, cl)) {
cl->status = -ENODEV;
- cb_pos->buf_idx = 0;
- list_del(&cb_pos->list);
+ cb->buf_idx = 0;
+ list_del(&cb->list);
return -ENODEV;
- } else {
- list_move_tail(&cb_pos->list, &dev->ctrl_rd_list.list);
- cl->timer_count = MEI_CONNECT_TIMEOUT;
}
+
+ list_move_tail(&cb->list, &dev->ctrl_rd_list.list);
+ cl->timer_count = MEI_CONNECT_TIMEOUT;
return 0;
}
/**
- * mei_irq_thread_write_complete - write messages to device.
+ * mei_cl_irq_write_complete - write messages to device.
*
- * @dev: the device structure.
- * @slots: free slots.
+ * @cl: client
* @cb: callback block.
+ * @slots: free slots.
* @cmpl_list: complete list.
*
* returns 0, OK; otherwise, error.
*/
-static int mei_irq_thread_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list)
+static int mei_cl_irq_write_complete(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list)
{
+ struct mei_device *dev = cl->dev;
struct mei_msg_hdr mei_hdr;
- struct mei_cl *cl = cb->cl;
size_t len = cb->request_buffer.size - cb->buf_idx;
u32 msg_slots = mei_data2slots(len);
@@ -481,7 +455,7 @@
{
struct mei_cl *cl;
- struct mei_cl_cb *pos = NULL, *next = NULL;
+ struct mei_cl_cb *cb, *next;
struct mei_cl_cb *list;
s32 slots;
int ret;
@@ -498,19 +472,19 @@
dev_dbg(&dev->pdev->dev, "complete all waiting for write cb.\n");
list = &dev->write_waiting_list;
- list_for_each_entry_safe(pos, next, &list->list, list) {
- cl = pos->cl;
+ list_for_each_entry_safe(cb, next, &list->list, list) {
+ cl = cb->cl;
if (cl == NULL)
continue;
cl->status = 0;
- list_del(&pos->list);
+ list_del(&cb->list);
if (MEI_WRITING == cl->writing_state &&
- pos->fop_type == MEI_FOP_WRITE &&
+ cb->fop_type == MEI_FOP_WRITE &&
cl != &dev->iamthif_cl) {
dev_dbg(&dev->pdev->dev, "MEI WRITE COMPLETE\n");
cl->writing_state = MEI_WRITE_COMPLETE;
- list_add_tail(&pos->list, &cmpl_list->list);
+ list_add_tail(&cb->list, &cmpl_list->list);
}
if (cl == &dev->iamthif_cl) {
dev_dbg(&dev->pdev->dev, "check iamthif flow control.\n");
@@ -552,25 +526,23 @@
/* complete control write list CB */
dev_dbg(&dev->pdev->dev, "complete control write list cb.\n");
- list_for_each_entry_safe(pos, next, &dev->ctrl_wr_list.list, list) {
- cl = pos->cl;
+ list_for_each_entry_safe(cb, next, &dev->ctrl_wr_list.list, list) {
+ cl = cb->cl;
if (!cl) {
- list_del(&pos->list);
+ list_del(&cb->list);
return -ENODEV;
}
- switch (pos->fop_type) {
+ switch (cb->fop_type) {
case MEI_FOP_CLOSE:
/* send disconnect message */
- ret = _mei_irq_thread_close(dev, &slots, pos,
- cl, cmpl_list);
+ ret = mei_cl_irq_close(cl, cb, &slots, cmpl_list);
if (ret)
return ret;
break;
case MEI_FOP_READ:
/* send flow control message */
- ret = _mei_irq_thread_read(dev, &slots, pos,
- cl, cmpl_list);
+ ret = mei_cl_irq_read(cl, cb, &slots, cmpl_list);
if (ret)
return ret;
@@ -579,8 +551,7 @@
/* connect message */
if (mei_cl_is_other_connecting(cl))
continue;
- ret = _mei_irq_thread_ioctl(dev, &slots, pos,
- cl, cmpl_list);
+ ret = mei_cl_irq_ioctl(cl, cb, &slots, cmpl_list);
if (ret)
return ret;
@@ -593,8 +564,8 @@
}
/* complete write list CB */
dev_dbg(&dev->pdev->dev, "complete write list cb.\n");
- list_for_each_entry_safe(pos, next, &dev->write_list.list, list) {
- cl = pos->cl;
+ list_for_each_entry_safe(cb, next, &dev->write_list.list, list) {
+ cl = cb->cl;
if (cl == NULL)
continue;
if (mei_cl_flow_ctrl_creds(cl) <= 0) {
@@ -605,14 +576,13 @@
}
if (cl == &dev->iamthif_cl)
- ret = mei_amthif_irq_write_complete(dev, &slots,
- pos, cmpl_list);
+ ret = mei_amthif_irq_write_complete(cl, cb,
+ &slots, cmpl_list);
else
- ret = mei_irq_thread_write_complete(dev, &slots, pos,
- cmpl_list);
+ ret = mei_cl_irq_write_complete(cl, cb,
+ &slots, cmpl_list);
if (ret)
return ret;
-
}
return 0;
}
diff --git a/drivers/misc/mei/mei_dev.h b/drivers/misc/mei/mei_dev.h
index 4de5140..197ba64 100644
--- a/drivers/misc/mei/mei_dev.h
+++ b/drivers/misc/mei/mei_dev.h
@@ -502,8 +502,8 @@
void mei_amthif_run_next_cmd(struct mei_device *dev);
-int mei_amthif_irq_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list);
+int mei_amthif_irq_write_complete(struct mei_cl *cl, struct mei_cl_cb *cb,
+ s32 *slots, struct mei_cl_cb *cmpl_list);
void mei_amthif_complete(struct mei_device *dev, struct mei_cl_cb *cb);
int mei_amthif_irq_read_msg(struct mei_device *dev,
@@ -522,15 +522,6 @@
*/
extern const uuid_le mei_nfc_guid;
-int mei_amthif_irq_write_complete(struct mei_device *dev, s32 *slots,
- struct mei_cl_cb *cb, struct mei_cl_cb *cmpl_list);
-
-void mei_amthif_complete(struct mei_device *dev, struct mei_cl_cb *cb);
-int mei_amthif_irq_read_message(struct mei_cl_cb *complete_list,
- struct mei_device *dev, struct mei_msg_hdr *mei_hdr);
-int mei_amthif_irq_read(struct mei_device *dev, s32 *slots);
-
-
int mei_wd_send(struct mei_device *dev);
int mei_wd_stop(struct mei_device *dev);
int mei_wd_host_init(struct mei_device *dev);
diff --git a/drivers/misc/sram.c b/drivers/misc/sram.c
index 437192e..4a93886 100644
--- a/drivers/misc/sram.c
+++ b/drivers/misc/sram.c
@@ -50,9 +50,10 @@
size = resource_size(res);
- virt_base = devm_request_and_ioremap(&pdev->dev, res);
- if (!virt_base)
- return -EADDRNOTAVAIL;
+ virt_base = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(virt_base))
+ return PTR_ERR(virt_base);
+
sram = devm_kzalloc(&pdev->dev, sizeof(*sram), GFP_KERNEL);
if (!sram)
diff --git a/drivers/misc/tsl2550.c b/drivers/misc/tsl2550.c
index 1dfde4d..5bc10fa1 100644
--- a/drivers/misc/tsl2550.c
+++ b/drivers/misc/tsl2550.c
@@ -204,7 +204,7 @@
unsigned long val = simple_strtoul(buf, NULL, 10);
int ret;
- if (val < 0 || val > 1)
+ if (val > 1)
return -EINVAL;
mutex_lock(&data->update_lock);
@@ -236,7 +236,7 @@
unsigned long val = simple_strtoul(buf, NULL, 10);
int ret;
- if (val < 0 || val > 1)
+ if (val > 1)
return -EINVAL;
if (data->power_state == 0)
diff --git a/drivers/uio/uio_aec.c b/drivers/uio/uio_aec.c
index 1548982..f3611c2 100644
--- a/drivers/uio/uio_aec.c
+++ b/drivers/uio/uio_aec.c
@@ -160,17 +160,5 @@
.remove = remove,
};
-static int __init aectc_init(void)
-{
- return pci_register_driver(&pci_driver);
-}
-
-static void __exit aectc_exit(void)
-{
- pci_unregister_driver(&pci_driver);
-}
-
+module_pci_driver(pci_driver);
MODULE_LICENSE("GPL");
-
-module_init(aectc_init);
-module_exit(aectc_exit);
diff --git a/drivers/uio/uio_cif.c b/drivers/uio/uio_cif.c
index 7dd6fc6..22cdf38 100644
--- a/drivers/uio/uio_cif.c
+++ b/drivers/uio/uio_cif.c
@@ -135,19 +135,7 @@
.remove = hilscher_pci_remove,
};
-static int __init hilscher_init_module(void)
-{
- return pci_register_driver(&hilscher_pci_driver);
-}
-
-static void __exit hilscher_exit_module(void)
-{
- pci_unregister_driver(&hilscher_pci_driver);
-}
-
-module_init(hilscher_init_module);
-module_exit(hilscher_exit_module);
-
+module_pci_driver(hilscher_pci_driver);
MODULE_DEVICE_TABLE(pci, hilscher_pci_ids);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Hans J. Koch, Benedikt Spranger");
diff --git a/drivers/uio/uio_netx.c b/drivers/uio/uio_netx.c
index 6a4ba5e..28a766b 100644
--- a/drivers/uio/uio_netx.c
+++ b/drivers/uio/uio_netx.c
@@ -174,19 +174,7 @@
.remove = netx_pci_remove,
};
-static int __init netx_init_module(void)
-{
- return pci_register_driver(&netx_pci_driver);
-}
-
-static void __exit netx_exit_module(void)
-{
- pci_unregister_driver(&netx_pci_driver);
-}
-
-module_init(netx_init_module);
-module_exit(netx_exit_module);
-
+module_pci_driver(netx_pci_driver);
MODULE_DEVICE_TABLE(pci, netx_pci_ids);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR("Hans J. Koch, Manuel Traut");
diff --git a/drivers/uio/uio_pci_generic.c b/drivers/uio/uio_pci_generic.c
index 14aa10c..077ae12 100644
--- a/drivers/uio/uio_pci_generic.c
+++ b/drivers/uio/uio_pci_generic.c
@@ -113,27 +113,14 @@
kfree(gdev);
}
-static struct pci_driver driver = {
+static struct pci_driver uio_pci_driver = {
.name = "uio_pci_generic",
.id_table = NULL, /* only dynamic id's */
.probe = probe,
.remove = remove,
};
-static int __init init(void)
-{
- pr_info(DRIVER_DESC " version: " DRIVER_VERSION "\n");
- return pci_register_driver(&driver);
-}
-
-static void __exit cleanup(void)
-{
- pci_unregister_driver(&driver);
-}
-
-module_init(init);
-module_exit(cleanup);
-
+module_pci_driver(uio_pci_driver);
MODULE_VERSION(DRIVER_VERSION);
MODULE_LICENSE("GPL v2");
MODULE_AUTHOR(DRIVER_AUTHOR);
diff --git a/drivers/uio/uio_sercos3.c b/drivers/uio/uio_sercos3.c
index 81a10a5..5419832 100644
--- a/drivers/uio/uio_sercos3.c
+++ b/drivers/uio/uio_sercos3.c
@@ -226,19 +226,7 @@
.remove = sercos3_pci_remove,
};
-static int __init sercos3_init_module(void)
-{
- return pci_register_driver(&sercos3_pci_driver);
-}
-
-static void __exit sercos3_exit_module(void)
-{
- pci_unregister_driver(&sercos3_pci_driver);
-}
-
-module_init(sercos3_init_module);
-module_exit(sercos3_exit_module);
-
+module_pci_driver(sercos3_pci_driver);
MODULE_DESCRIPTION("UIO driver for the Automata Sercos III PCI card");
MODULE_AUTHOR("John Ogness <john.ogness@linutronix.de>");
MODULE_LICENSE("GPL v2");
diff --git a/drivers/w1/masters/w1-gpio.c b/drivers/w1/masters/w1-gpio.c
index 46d9701..f54ece2 100644
--- a/drivers/w1/masters/w1-gpio.c
+++ b/drivers/w1/masters/w1-gpio.c
@@ -16,7 +16,6 @@
#include <linux/gpio.h>
#include <linux/of_platform.h>
#include <linux/of_gpio.h>
-#include <linux/pinctrl/consumer.h>
#include <linux/err.h>
#include <linux/of.h>
@@ -78,13 +77,8 @@
{
struct w1_bus_master *master;
struct w1_gpio_platform_data *pdata;
- struct pinctrl *pinctrl;
int err;
- pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
- if (IS_ERR(pinctrl))
- dev_warn(&pdev->dev, "unable to select pin group\n");
-
if (of_have_populated_dt()) {
err = w1_gpio_probe_dt(pdev);
if (err < 0) {