ARM: dts: msm: add VDD_APC0/1 CPR regulator configurations for sdm845v2
Specify SDM845v2 configuration values for VDD_APC0 and VDD_APC1
cprh-kbss-regulator devices.
Change-Id: Ia225fbaae1f9bf97fe858335c6402d24c28d0602
Signed-off-by: David Collins <collinsd@codeaurora.org>
diff --git a/arch/arm64/boot/dts/qcom/sdm845-v2.dtsi b/arch/arm64/boot/dts/qcom/sdm845-v2.dtsi
index da30cf2..8f498b1 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-v2.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-v2.dtsi
@@ -25,6 +25,418 @@
qcom,devfreq,freq-table = <50000000 200000000>;
};
+/delete-node/ &apc0_cpr;
+/delete-node/ &apc1_cpr;
+
+&soc {
+ /* CPR controller regulators */
+ apc0_cpr: cprh-ctrl@17dc0000 {
+ compatible = "qcom,cprh-sdm845-v2-kbss-regulator";
+ reg = <0x17dc0000 0x4000>,
+ <0x00784000 0x1000>,
+ <0x17840000 0x1000>;
+ reg-names = "cpr_ctrl", "fuse_base", "saw";
+ clocks = <&clock_gcc GCC_CPUSS_RBCPR_CLK>;
+ clock-names = "core_clk";
+ qcom,cpr-ctrl-name = "apc0";
+ qcom,cpr-controller-id = <0>;
+
+ qcom,cpr-sensor-time = <1000>;
+ qcom,cpr-loop-time = <5000000>;
+ qcom,cpr-idle-cycles = <15>;
+ qcom,cpr-up-down-delay-time = <3000>;
+ qcom,cpr-step-quot-init-min = <11>;
+ qcom,cpr-step-quot-init-max = <12>;
+ qcom,cpr-count-mode = <0>; /* All at once */
+ qcom,cpr-count-repeat = <20>;
+ qcom,cpr-down-error-step-limit = <1>;
+ qcom,cpr-up-error-step-limit = <1>;
+ qcom,cpr-corner-switch-delay-time = <1042>;
+ qcom,cpr-voltage-settling-time = <1760>;
+ qcom,cpr-reset-step-quot-loop-en;
+
+ qcom,voltage-step = <4000>;
+ qcom,voltage-base = <352000>;
+ qcom,cpr-saw-use-unit-mV;
+
+ qcom,saw-avs-ctrl = <0x101C031>;
+ qcom,saw-avs-limit = <0x3B803B8>;
+
+ qcom,cpr-enable;
+ qcom,cpr-hw-closed-loop;
+
+ qcom,cpr-panic-reg-addr-list =
+ <0x17dc3a84 0x17dc3a88 0x17840c18>;
+ qcom,cpr-panic-reg-name-list =
+ "APSS_SILVER_CPRH_STATUS_0",
+ "APSS_SILVER_CPRH_STATUS_1",
+ "SILVER_SAW4_PMIC_STS";
+
+ qcom,cpr-aging-ref-voltage = <952000>;
+ vdd-supply = <&pm8998_s13>;
+
+ thread@0 {
+ qcom,cpr-thread-id = <0>;
+ qcom,cpr-consecutive-up = <0>;
+ qcom,cpr-consecutive-down = <0>;
+ qcom,cpr-up-threshold = <2>;
+ qcom,cpr-down-threshold = <2>;
+
+ apc0_pwrcl_vreg: regulator {
+ regulator-name = "apc0_pwrcl_corner";
+ regulator-min-microvolt = <1>;
+ regulator-max-microvolt = <18>;
+
+ qcom,cpr-fuse-corners = <4>;
+ qcom,cpr-fuse-combos = <16>;
+ qcom,cpr-speed-bins = <2>;
+ qcom,cpr-speed-bin-corners = <18 18>;
+ qcom,cpr-corners = <18>;
+
+ qcom,cpr-corner-fmax-map = <6 12 15 18>;
+
+ qcom,cpr-voltage-ceiling =
+ <828000 828000 828000 828000 828000
+ 828000 828000 828000 828000 828000
+ 828000 828000 828000 828000 828000
+ 884000 952000 952000>;
+
+ qcom,cpr-voltage-floor =
+ <568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000>;
+
+ qcom,cpr-floor-to-ceiling-max-range =
+ <32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 40000 40000>;
+
+ qcom,corner-frequencies =
+ <300000000 403200000 480000000
+ 576000000 652800000 748800000
+ 825600000 902400000 979200000
+ 1056000000 1132800000 1228800000
+ 1324800000 1420800000 1516800000
+ 1612800000 1689600000 1766400000>;
+
+ qcom,cpr-ro-scaling-factor =
+ <2594 2795 2576 2761 2469 2673 2198
+ 2553 3188 3255 3191 2962 3055 2984
+ 2043 2947>,
+ <2594 2795 2576 2761 2469 2673 2198
+ 2553 3188 3255 3191 2962 3055 2984
+ 2043 2947>,
+ <2259 2389 2387 2531 2294 2464 2218
+ 2476 2525 2855 2817 2836 2740 2490
+ 1950 2632>,
+ <2259 2389 2387 2531 2294 2464 2218
+ 2476 2525 2855 2817 2836 2740 2490
+ 1950 2632>;
+
+ qcom,cpr-open-loop-voltage-fuse-adjustment =
+ <100000 100000 100000 100000>;
+
+ qcom,cpr-closed-loop-voltage-fuse-adjustment =
+ <100000 100000 100000 100000>;
+
+ qcom,allow-voltage-interpolation;
+ qcom,allow-quotient-interpolation;
+ qcom,cpr-scaled-open-loop-voltage-as-ceiling;
+
+ qcom,cpr-aging-max-voltage-adjustment = <15000>;
+ qcom,cpr-aging-ref-corner = <18>;
+ qcom,cpr-aging-ro-scaling-factor = <1620>;
+ qcom,allow-aging-voltage-adjustment =
+ /* Speed bin 0 */
+ <0 1 1 1 1 1 1 1>,
+ /* Speed bin 1 */
+ <0 1 1 1 1 1 1 1>;
+ qcom,allow-aging-open-loop-voltage-adjustment =
+ <1>;
+ };
+ };
+
+ thread@1 {
+ qcom,cpr-thread-id = <1>;
+ qcom,cpr-consecutive-up = <0>;
+ qcom,cpr-consecutive-down = <0>;
+ qcom,cpr-up-threshold = <2>;
+ qcom,cpr-down-threshold = <2>;
+
+ apc0_l3_vreg: regulator {
+ regulator-name = "apc0_l3_corner";
+ regulator-min-microvolt = <1>;
+ regulator-max-microvolt = <14>;
+
+ qcom,cpr-fuse-corners = <4>;
+ qcom,cpr-fuse-combos = <16>;
+ qcom,cpr-speed-bins = <2>;
+ qcom,cpr-speed-bin-corners = <14 14>;
+ qcom,cpr-corners = <14>;
+
+ qcom,cpr-corner-fmax-map = <4 8 11 14>;
+
+ qcom,cpr-voltage-ceiling =
+ <828000 828000 828000 828000 828000
+ 828000 828000 828000 828000 828000
+ 828000 884000 884000 952000>;
+
+ qcom,cpr-voltage-floor =
+ <568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000>;
+
+ qcom,cpr-floor-to-ceiling-max-range =
+ <32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 40000>;
+
+ qcom,corner-frequencies =
+ <300000000 403200000 480000000
+ 576000000 652800000 748800000
+ 844800000 940800000 1036800000
+ 1132800000 1209600000 1305600000
+ 1401600000 1478400000>;
+
+ qcom,cpr-ro-scaling-factor =
+ <2857 3056 2828 2952 2699 2796 2447
+ 2631 2630 2579 2244 3343 3287 3137
+ 3164 2656>,
+ <2857 3056 2828 2952 2699 2796 2447
+ 2631 2630 2579 2244 3343 3287 3137
+ 3164 2656>,
+ <2439 2577 2552 2667 2461 2577 2394
+ 2536 2132 2307 2191 2903 2838 2912
+ 2501 2095>,
+ <2439 2577 2552 2667 2461 2577 2394
+ 2536 2132 2307 2191 2903 2838 2912
+ 2501 2095>;
+
+ qcom,cpr-open-loop-voltage-fuse-adjustment =
+ <100000 100000 100000 100000>;
+
+ qcom,cpr-closed-loop-voltage-fuse-adjustment =
+ <100000 100000 100000 100000>;
+
+ qcom,allow-voltage-interpolation;
+ qcom,allow-quotient-interpolation;
+ qcom,cpr-scaled-open-loop-voltage-as-ceiling;
+
+ qcom,cpr-aging-max-voltage-adjustment = <15000>;
+ qcom,cpr-aging-ref-corner = <14>;
+ qcom,cpr-aging-ro-scaling-factor = <1620>;
+ qcom,allow-aging-voltage-adjustment =
+ /* Speed bin 0 */
+ <0 1 1 1 1 1 1 1>,
+ /* Speed bin 1 */
+ <0 1 1 1 1 1 1 1>;
+ qcom,allow-aging-open-loop-voltage-adjustment =
+ <1>;
+ };
+ };
+ };
+
+ apc1_cpr: cprh-ctrl@17db0000 {
+ compatible = "qcom,cprh-sdm845-v2-kbss-regulator";
+ reg = <0x17db0000 0x4000>,
+ <0x00784000 0x1000>,
+ <0x17830000 0x1000>;
+ reg-names = "cpr_ctrl", "fuse_base", "saw";
+ clocks = <&clock_gcc GCC_CPUSS_RBCPR_CLK>;
+ clock-names = "core_clk";
+ qcom,cpr-ctrl-name = "apc1";
+ qcom,cpr-controller-id = <1>;
+
+ qcom,cpr-sensor-time = <1000>;
+ qcom,cpr-loop-time = <5000000>;
+ qcom,cpr-idle-cycles = <15>;
+ qcom,cpr-up-down-delay-time = <3000>;
+ qcom,cpr-step-quot-init-min = <9>;
+ qcom,cpr-step-quot-init-max = <14>;
+ qcom,cpr-count-mode = <0>; /* All at once */
+ qcom,cpr-count-repeat = <20>;
+ qcom,cpr-down-error-step-limit = <1>;
+ qcom,cpr-up-error-step-limit = <1>;
+ qcom,cpr-corner-switch-delay-time = <1042>;
+ qcom,cpr-voltage-settling-time = <1760>;
+ qcom,cpr-reset-step-quot-loop-en;
+
+ qcom,apm-threshold-voltage = <800000>;
+ qcom,apm-crossover-voltage = <880000>;
+ qcom,mem-acc-threshold-voltage = <852000>;
+ qcom,mem-acc-crossover-voltage = <852000>;
+
+ qcom,voltage-step = <4000>;
+ qcom,voltage-base = <352000>;
+ qcom,cpr-saw-use-unit-mV;
+
+ qcom,saw-avs-ctrl = <0x101C031>;
+ qcom,saw-avs-limit = <0x4700470>;
+
+ qcom,cpr-enable;
+ qcom,cpr-hw-closed-loop;
+
+ qcom,cpr-panic-reg-addr-list =
+ <0x17db3a84 0x17830c18>;
+ qcom,cpr-panic-reg-name-list =
+ "APSS_GOLD_CPRH_STATUS_0", "GOLD_SAW4_PMIC_STS";
+
+ qcom,cpr-aging-ref-voltage = <1136000>;
+ vdd-supply = <&pm8998_s12>;
+
+ thread@0 {
+ qcom,cpr-thread-id = <0>;
+ qcom,cpr-consecutive-up = <0>;
+ qcom,cpr-consecutive-down = <0>;
+ qcom,cpr-up-threshold = <2>;
+ qcom,cpr-down-threshold = <2>;
+
+ apc1_perfcl_vreg: regulator {
+ regulator-name = "apc1_perfcl_corner";
+ regulator-min-microvolt = <1>;
+ regulator-max-microvolt = <33>;
+
+ qcom,cpr-fuse-corners = <5>;
+ qcom,cpr-fuse-combos = <16>;
+ qcom,cpr-speed-bins = <2>;
+ qcom,cpr-speed-bin-corners = <28 31>;
+ qcom,cpr-corners =
+ /* Speed bin 0 */
+ <28 28 28 28 28 28 28 28>,
+ /* Speed bin 1 */
+ <31 31 31 31 31 31 31 31>;
+
+ qcom,cpr-corner-fmax-map =
+ /* Speed bin 0 */
+ <7 14 22 27 28>,
+ /* Speed bin 1 */
+ <7 14 22 27 31>;
+
+ qcom,cpr-voltage-ceiling =
+ /* Speed bin 0 */
+ <828000 828000 828000 828000 828000
+ 828000 828000 828000 828000 828000
+ 828000 828000 828000 828000 828000
+ 828000 828000 828000 884000 884000
+ 884000 884000 1104000 1104000 1104000
+ 1104000 1136000 1136000>,
+ /* Speed bin 1 */
+ <828000 828000 828000 828000 828000
+ 828000 828000 828000 828000 828000
+ 828000 828000 828000 828000 828000
+ 828000 828000 828000 884000 884000
+ 884000 884000 1104000 1104000 1104000
+ 1104000 1136000 1136000 1136000 1136000
+ 1136000>;
+
+ qcom,cpr-voltage-floor =
+ /* Speed bin 0 */
+ <568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000>,
+ /* Speed bin 1 */
+ <568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000 568000 568000 568000 568000
+ 568000>;
+
+ qcom,cpr-floor-to-ceiling-max-range =
+ /* Speed bin 0 */
+ <32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000>,
+ /* Speed bin 1 */
+ <32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 32000 32000 32000
+ 32000 32000 40000 40000 40000
+ 40000>;
+
+ qcom,corner-frequencies =
+ /* Speed bin 0 */
+ <300000000 403200000 480000000
+ 576000000 652800000 748800000
+ 825600000 902400000 979200000
+ 1056000000 1132800000 1209600000
+ 1286400000 1363200000 1459200000
+ 1536000000 1612800000 1689600000
+ 1766400000 1843200000 1920000000
+ 1996800000 2092800000 2169600000
+ 2246400000 2323200000 2400000000
+ 2400000000>,
+ /* Speed bin 1 */
+ <300000000 403200000 480000000
+ 576000000 652800000 748800000
+ 825600000 902400000 979200000
+ 1056000000 1132800000 1209600000
+ 1286400000 1363200000 1459200000
+ 1536000000 1612800000 1689600000
+ 1766400000 1843200000 1920000000
+ 1996800000 2092800000 2169600000
+ 2246400000 2323200000 2400000000
+ 2476800000 2553600000 2630400000
+ 2707200000>;
+
+ qcom,cpr-ro-scaling-factor =
+ <2857 3056 2828 2952 2699 2796 2447
+ 2631 2630 2579 2244 3343 3287 3137
+ 3164 2656>,
+ <2857 3056 2828 2952 2699 2796 2447
+ 2631 2630 2579 2244 3343 3287 3137
+ 3164 2656>,
+ <2086 2208 2273 2408 2203 2327 2213
+ 2340 1755 2039 2049 2474 2437 2618
+ 2003 1675>,
+ <2086 2208 2273 2408 2203 2327 2213
+ 2340 1755 2039 2049 2474 2437 2618
+ 2003 1675>,
+ <2086 2208 2273 2408 2203 2327 2213
+ 2340 1755 2039 2049 2474 2437 2618
+ 2003 1675>;
+
+ qcom,cpr-open-loop-voltage-fuse-adjustment =
+ <100000 100000 100000 100000 100000>;
+
+ qcom,cpr-closed-loop-voltage-fuse-adjustment =
+ <100000 100000 100000 100000 100000>;
+
+ qcom,allow-voltage-interpolation;
+ qcom,allow-quotient-interpolation;
+ qcom,cpr-scaled-open-loop-voltage-as-ceiling;
+
+ qcom,cpr-aging-max-voltage-adjustment = <15000>;
+ qcom,cpr-aging-ref-corner = <27 31>;
+ qcom,cpr-aging-ro-scaling-factor = <1700>;
+ qcom,allow-aging-voltage-adjustment =
+ /* Speed bin 0 */
+ <0 1 1 1 1 1 1 1>,
+ /* Speed bin 1 */
+ <0 1 1 1 1 1 1 1>;
+ qcom,allow-aging-open-loop-voltage-adjustment =
+ <1>;
+ };
+ };
+ };
+};
+
+&clock_cpucc {
+ vdd-l3-supply = <&apc0_l3_vreg>;
+ vdd-pwrcl-supply = <&apc0_pwrcl_vreg>;
+};
+
&clock_gcc {
compatible = "qcom,gcc-sdm845-v2";
};