hwmon: Driver for MAX16065 System Manager and compatibles
This patch adds hardware monitoring support for Maxim MAX16065, MAX16066,
MAX16067, MAX16068, MAX16070, and MAX16071 flash-configurable system managers
with nonvolatile fault registers.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Jean Delvare <khali@linux-fr.org>
diff --git a/Documentation/hwmon/max16065 b/Documentation/hwmon/max16065
new file mode 100644
index 0000000..44b4f61
--- /dev/null
+++ b/Documentation/hwmon/max16065
@@ -0,0 +1,98 @@
+Kernel driver max16065
+======================
+
+Supported chips:
+ * Maxim MAX16065, MAX16066
+ Prefixes: 'max16065', 'max16066'
+ Addresses scanned: -
+ Datasheet:
+ http://datasheets.maxim-ic.com/en/ds/MAX16065-MAX16066.pdf
+ * Maxim MAX16067
+ Prefix: 'max16067'
+ Addresses scanned: -
+ Datasheet:
+ http://datasheets.maxim-ic.com/en/ds/MAX16067.pdf
+ * Maxim MAX16068
+ Prefix: 'max16068'
+ Addresses scanned: -
+ Datasheet:
+ http://datasheets.maxim-ic.com/en/ds/MAX16068.pdf
+ * Maxim MAX16070/MAX16071
+ Prefixes: 'max16070', 'max16071'
+ Addresses scanned: -
+ Datasheet:
+ http://datasheets.maxim-ic.com/en/ds/MAX16070-MAX16071.pdf
+
+
+Author: Guenter Roeck <guenter.roeck@ericsson.com>
+
+
+Description
+-----------
+
+[From datasheets] The MAX16065/MAX16066 flash-configurable system managers
+monitor and sequence multiple system voltages. The MAX16065/MAX16066 can also
+accurately monitor (+/-2.5%) one current channel using a dedicated high-side
+current-sense amplifier. The MAX16065 manages up to twelve system voltages
+simultaneously, and the MAX16066 manages up to eight supply voltages.
+
+The MAX16067 flash-configurable system manager monitors and sequences multiple
+system voltages. The MAX16067 manages up to six system voltages simultaneously.
+
+The MAX16068 flash-configurable system manager monitors and manages up to six
+system voltages simultaneously.
+
+The MAX16070/MAX16071 flash-configurable system monitors supervise multiple
+system voltages. The MAX16070/MAX16071 can also accurately monitor (+/-2.5%)
+one current channel using a dedicated high-side current-sense amplifier. The
+MAX16070 monitors up to twelve system voltages simultaneously, and the MAX16071
+monitors up to eight supply voltages.
+
+Each monitored channel has its own low and high critical limits. MAX16065,
+MAX16066, MAX16070, and MAX16071 support an additional limit which is
+configurable as either low or high secondary limit. MAX16065, MAX16066,
+MAX16070, and MAX16071 also support supply current monitoring.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for devices, since there is no register which
+can be safely used to identify the chip. You will have to instantiate
+the devices explicitly. Please see Documentation/i2c/instantiating-devices for
+details.
+
+
+Sysfs entries
+-------------
+
+in[0-11]_input Input voltage measurements.
+
+in12_input Voltage on CSP (Current Sense Positive) pin.
+ Only if the chip supports current sensing and if
+ current sensing is enabled.
+
+in[0-11]_min Low warning limit.
+ Supported on MAX16065, MAX16066, MAX16070, and MAX16071
+ only.
+
+in[0-11]_max High warning limit.
+ Supported on MAX16065, MAX16066, MAX16070, and MAX16071
+ only.
+
+ Either low or high warning limits are supported
+ (depending on chip configuration), but not both.
+
+in[0-11]_lcrit Low critical limit.
+
+in[0-11]_crit High critical limit.
+
+in[0-11]_alarm Input voltage alarm.
+
+curr1_input Current sense input; only if the chip supports current
+ sensing and if current sensing is enabled.
+ Displayed current assumes 0.001 Ohm current sense
+ resistor.
+
+curr1_alarm Overcurrent alarm; only if the chip supports current
+ sensing and if current sensing is enabled.