diff --git a/drivers/usb/host/xhci-hub.c b/drivers/usb/host/xhci-hub.c
index 0230965..f980c23 100644
--- a/drivers/usb/host/xhci-hub.c
+++ b/drivers/usb/host/xhci-hub.c
@@ -733,8 +733,30 @@
 		if ((raw_port_status & PORT_RESET) ||
 				!(raw_port_status & PORT_PE))
 			return 0xffffffff;
-		if (time_after_eq(jiffies,
-					bus_state->resume_done[wIndex])) {
+		/* did port event handler already start resume timing? */
+		if (!bus_state->resume_done[wIndex]) {
+			/* If not, maybe we are in a host initated resume? */
+			if (test_bit(wIndex, &bus_state->resuming_ports)) {
+				/* Host initated resume doesn't time the resume
+				 * signalling using resume_done[].
+				 * It manually sets RESUME state, sleeps 20ms
+				 * and sets U0 state. This should probably be
+				 * changed, but not right now.
+				 */
+			} else {
+				/* port resume was discovered now and here,
+				 * start resume timing
+				 */
+				unsigned long timeout = jiffies +
+					msecs_to_jiffies(USB_RESUME_TIMEOUT);
+
+				set_bit(wIndex, &bus_state->resuming_ports);
+				bus_state->resume_done[wIndex] = timeout;
+				mod_timer(&hcd->rh_timer, timeout);
+			}
+		/* Has resume been signalled for USB_RESUME_TIME yet? */
+		} else if (time_after_eq(jiffies,
+					 bus_state->resume_done[wIndex])) {
 			int time_left;
 
 			xhci_dbg(xhci, "Resume USB2 port %d\n",
@@ -775,13 +797,26 @@
 		} else {
 			/*
 			 * The resume has been signaling for less than
-			 * 20ms. Report the port status as SUSPEND,
-			 * let the usbcore check port status again
-			 * and clear resume signaling later.
+			 * USB_RESUME_TIME. Report the port status as SUSPEND,
+			 * let the usbcore check port status again and clear
+			 * resume signaling later.
 			 */
 			status |= USB_PORT_STAT_SUSPEND;
 		}
 	}
+	/*
+	 * Clear stale usb2 resume signalling variables in case port changed
+	 * state during resume signalling. For example on error
+	 */
+	if ((bus_state->resume_done[wIndex] ||
+	     test_bit(wIndex, &bus_state->resuming_ports)) &&
+	    (raw_port_status & PORT_PLS_MASK) != XDEV_U3 &&
+	    (raw_port_status & PORT_PLS_MASK) != XDEV_RESUME) {
+		bus_state->resume_done[wIndex] = 0;
+		clear_bit(wIndex, &bus_state->resuming_ports);
+	}
+
+
 	if ((raw_port_status & PORT_PLS_MASK) == XDEV_U0 &&
 	    (raw_port_status & PORT_POWER)) {
 		if (bus_state->suspended_ports & (1 << wIndex)) {
@@ -1115,6 +1150,7 @@
 				if ((temp & PORT_PE) == 0)
 					goto error;
 
+				set_bit(wIndex, &bus_state->resuming_ports);
 				xhci_set_link_state(xhci, port_array, wIndex,
 							XDEV_RESUME);
 				spin_unlock_irqrestore(&xhci->lock, flags);
@@ -1122,6 +1158,7 @@
 				spin_lock_irqsave(&xhci->lock, flags);
 				xhci_set_link_state(xhci, port_array, wIndex,
 							XDEV_U0);
+				clear_bit(wIndex, &bus_state->resuming_ports);
 			}
 			bus_state->port_c_suspend |= 1 << wIndex;