staging: bcm: Replace FALSE with false
Replace user-defined type FALSE with C defined false keyword.
Signed-off-by: Lisa Nguyen <lisa@xenapiadmin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/staging/bcm/led_control.c b/drivers/staging/bcm/led_control.c
index 194edd7..eee4f47 100644
--- a/drivers/staging/bcm/led_control.c
+++ b/drivers/staging/bcm/led_control.c
@@ -18,7 +18,7 @@
INT Status;
Status = (Adapter->gpioBitMap & gpios) ^ gpios;
if (Status)
- return FALSE;
+ return false;
else
return TRUE;
}
@@ -27,7 +27,7 @@
ULONG timeout, INT num_of_time, enum bcm_led_events currdriverstate)
{
int Status = STATUS_SUCCESS;
- bool bInfinite = FALSE;
+ bool bInfinite = false;
/* Check if num_of_time is -ve. If yes, blink led in infinite loop */
if (num_of_time < 0) {
@@ -67,7 +67,7 @@
currdriverstate != Adapter->DriverState ||
kthread_should_stop(),
msecs_to_jiffies(timeout));
- if (bInfinite == FALSE)
+ if (bInfinite == false)
num_of_time--;
}
return Status;
@@ -120,7 +120,7 @@
num_of_time_tx = ScaleRateofTransfer((ULONG)rate_of_transfer_tx);
num_of_time_rx = ScaleRateofTransfer((ULONG)rate_of_transfer_rx);
- while ((Adapter->device_removed == FALSE)) {
+ while ((Adapter->device_removed == false)) {
timeout = 50;
/*
* Blink Tx and Rx LED when both Tx and Rx is
@@ -499,10 +499,10 @@
/* Read the GPIO numbers from EEPROM */
Status = ReadLEDInformationFromEEPROM(Adapter, GPIO_Array);
if (Status == STATUS_IMAGE_CHECKSUM_MISMATCH) {
- *bEnableThread = FALSE;
+ *bEnableThread = false;
return STATUS_SUCCESS;
} else if (Status) {
- *bEnableThread = FALSE;
+ *bEnableThread = false;
return Status;
}
@@ -561,7 +561,7 @@
uiNum_of_LED_Type++;
}
if (uiNum_of_LED_Type >= NUM_OF_LEDS)
- *bEnableThread = FALSE;
+ *bEnableThread = false;
return Status;
}
@@ -602,7 +602,7 @@
BCM_DEBUG_PRINT (Adapter, DBG_TYPE_OTHERS, LED_DUMP_INFO,
DBG_LVL_ALL, "LED Thread: WRM Failed\n");
- Adapter->LEDInfo.bIdle_led_off = FALSE;
+ Adapter->LEDInfo.bIdle_led_off = false;
}
static INT BcmGetGPIOPinInfo(struct bcm_mini_adapter *Adapter, UCHAR *GPIO_num_tx,
@@ -660,7 +660,7 @@
UCHAR dummyIndex = 0;
/* currdriverstate = Adapter->DriverState; */
- Adapter->LEDInfo.bIdleMode_tx_from_host = FALSE;
+ Adapter->LEDInfo.bIdleMode_tx_from_host = false;
/*
* Wait till event is triggered
@@ -698,7 +698,7 @@
if (GPIO_num != DISABLE_GPIO_NUM)
TURN_OFF_LED(1 << GPIO_num, uiLedIndex);
- if (Adapter->LEDInfo.bLedInitDone == FALSE) {
+ if (Adapter->LEDInfo.bLedInitDone == false) {
LedGpioInit(Adapter);
Adapter->LEDInfo.bLedInitDone = TRUE;
}
@@ -757,7 +757,7 @@
UCHAR uiLEDTx = 0;
UCHAR uiLEDRx = 0;
currdriverstate = NORMAL_OPERATION;
- Adapter->LEDInfo.bIdle_led_off = FALSE;
+ Adapter->LEDInfo.bIdle_led_off = false;
BcmGetGPIOPinInfo(Adapter, &GPIO_num_tx,
&GPIO_num_rx, &uiLEDTx, &uiLEDRx,
@@ -803,7 +803,7 @@
}
/* Turn off LED And WAKE-UP for Sendinf IDLE mode ACK */
- Adapter->LEDInfo.bLedInitDone = FALSE;
+ Adapter->LEDInfo.bLedInitDone = false;
Adapter->LEDInfo.bIdle_led_off = TRUE;
wake_up(&Adapter->LEDInfo.idleModeSyncEvent);
GPIO_num = DISABLE_GPIO_NUM;
@@ -830,7 +830,7 @@
currdriverstate = LED_THREAD_INACTIVE;
Adapter->LEDInfo.led_thread_running =
BCM_LED_THREAD_RUNNING_INACTIVELY;
- Adapter->LEDInfo.bLedInitDone = FALSE;
+ Adapter->LEDInfo.bLedInitDone = false;
/* disable ALL LED */
for (uiIndex = 0; uiIndex < NUM_OF_LEDS; uiIndex++) {
if (Adapter->LEDInfo.LEDState[uiIndex].GPIO_Num
@@ -841,7 +841,7 @@
case LED_THREAD_ACTIVE:
BCM_DEBUG_PRINT(Adapter, DBG_TYPE_OTHERS, LED_DUMP_INFO,
DBG_LVL_ALL, "Activating LED thread again...");
- if (Adapter->LinkUpStatus == FALSE)
+ if (Adapter->LinkUpStatus == false)
Adapter->DriverState = NO_NETWORK_ENTRY;
else
Adapter->DriverState = NORMAL_OPERATION;
@@ -899,7 +899,7 @@
init_waitqueue_head(&Adapter->LEDInfo.idleModeSyncEvent);
Adapter->LEDInfo.led_thread_running =
BCM_LED_THREAD_RUNNING_ACTIVELY;
- Adapter->LEDInfo.bIdle_led_off = FALSE;
+ Adapter->LEDInfo.bIdle_led_off = false;
Adapter->LEDInfo.led_cntrl_threadid =
kthread_run((int (*)(void *)) LEDControlThread,
Adapter, "led_control_thread");