Merge branch 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
* 'next/devel-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
ARM: EXYNOS: add support JPEG
ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
ARM: S5PV210: Add usb otg phy control
ARM: S3C64XX: Add usb otg phy control
ARM: EXYNOS: Enable l2 configuration through device tree
ARM: EXYNOS: remove useless code to save/restore L2
ARM: EXYNOS: save L2 settings during bootup
ARM: S5P: add L2 early resume code
ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
ARM: SAMSUNG: use spin_lock_irqsave() in clk_{enable,disable}
ARM: S3C64XX: Define some additional always off clocks
ARM: S3C64XX: Reduce residency requirement for cpuidle WFI mode
ARM: SAMSUNG: Add a callback 'notify_after' for PWM backlight control
ARM: SAMSUNG: add G2D to plat-s5p and mach-exynos
ARM: S3C64XX: Gate some more clocks by default
ARM: S3C64XX: Add basic cpuidle driver
diff --git a/arch/arm/mach-exynos/clock.c b/arch/arm/mach-exynos/clock.c
index 187287a..ac249e4 100644
--- a/arch/arm/mach-exynos/clock.c
+++ b/arch/arm/mach-exynos/clock.c
@@ -472,6 +472,11 @@
.enable = exynos4_clk_ip_cam_ctrl,
.ctrlbit = (1 << 5),
}, {
+ .name = "jpeg",
+ .id = 0,
+ .enable = exynos4_clk_ip_cam_ctrl,
+ .ctrlbit = (1 << 6),
+ }, {
.name = "fimc",
.devname = "exynos4-fimc.0",
.enable = exynos4_clk_ip_cam_ctrl,
diff --git a/arch/arm/mach-exynos/common.c b/arch/arm/mach-exynos/common.c
index 031c1e5..7f1f268 100644
--- a/arch/arm/mach-exynos/common.c
+++ b/arch/arm/mach-exynos/common.c
@@ -26,10 +26,12 @@
#include <asm/hardware/gic.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
+#include <asm/cacheflush.h>
#include <mach/regs-irq.h>
#include <mach/regs-pmu.h>
#include <mach/regs-gpio.h>
+#include <mach/pmu.h>
#include <plat/cpu.h>
#include <plat/clock.h>
@@ -45,6 +47,8 @@
#include <plat/regs-serial.h>
#include "common.h"
+#define L2_AUX_VAL 0x7C470001
+#define L2_AUX_MASK 0xC200ffff
static const char name_exynos4210[] = "EXYNOS4210";
static const char name_exynos4212[] = "EXYNOS4212";
@@ -173,7 +177,12 @@
}, {
.virtual = (unsigned long)S5P_VA_DMC0,
.pfn = __phys_to_pfn(EXYNOS4_PA_DMC0),
- .length = SZ_4K,
+ .length = SZ_64K,
+ .type = MT_DEVICE,
+ }, {
+ .virtual = (unsigned long)S5P_VA_DMC1,
+ .pfn = __phys_to_pfn(EXYNOS4_PA_DMC1),
+ .length = SZ_64K,
.type = MT_DEVICE,
}, {
.virtual = (unsigned long)S3C_VA_USB_HSPHY,
@@ -433,23 +442,48 @@
#ifdef CONFIG_CACHE_L2X0
static int __init exynos4_l2x0_cache_init(void)
{
- /* TAG, Data Latency Control: 2cycle */
- __raw_writel(0x110, S5P_VA_L2CC + L2X0_TAG_LATENCY_CTRL);
+ int ret;
+ ret = l2x0_of_init(L2_AUX_VAL, L2_AUX_MASK);
+ if (!ret) {
+ l2x0_regs_phys = virt_to_phys(&l2x0_saved_regs);
+ clean_dcache_area(&l2x0_regs_phys, sizeof(unsigned long));
+ return 0;
+ }
- if (soc_is_exynos4210())
- __raw_writel(0x110, S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL);
- else if (soc_is_exynos4212() || soc_is_exynos4412())
- __raw_writel(0x120, S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL);
+ if (!(__raw_readl(S5P_VA_L2CC + L2X0_CTRL) & 0x1)) {
+ l2x0_saved_regs.phy_base = EXYNOS4_PA_L2CC;
+ /* TAG, Data Latency Control: 2 cycles */
+ l2x0_saved_regs.tag_latency = 0x110;
- /* L2X0 Prefetch Control */
- __raw_writel(0x30000007, S5P_VA_L2CC + L2X0_PREFETCH_CTRL);
+ if (soc_is_exynos4212() || soc_is_exynos4412())
+ l2x0_saved_regs.data_latency = 0x120;
+ else
+ l2x0_saved_regs.data_latency = 0x110;
- /* L2X0 Power Control */
- __raw_writel(L2X0_DYNAMIC_CLK_GATING_EN | L2X0_STNDBY_MODE_EN,
- S5P_VA_L2CC + L2X0_POWER_CTRL);
+ l2x0_saved_regs.prefetch_ctrl = 0x30000007;
+ l2x0_saved_regs.pwr_ctrl =
+ (L2X0_DYNAMIC_CLK_GATING_EN | L2X0_STNDBY_MODE_EN);
- l2x0_init(S5P_VA_L2CC, 0x7C470001, 0xC200ffff);
+ l2x0_regs_phys = virt_to_phys(&l2x0_saved_regs);
+ __raw_writel(l2x0_saved_regs.tag_latency,
+ S5P_VA_L2CC + L2X0_TAG_LATENCY_CTRL);
+ __raw_writel(l2x0_saved_regs.data_latency,
+ S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL);
+
+ /* L2X0 Prefetch Control */
+ __raw_writel(l2x0_saved_regs.prefetch_ctrl,
+ S5P_VA_L2CC + L2X0_PREFETCH_CTRL);
+
+ /* L2X0 Power Control */
+ __raw_writel(l2x0_saved_regs.pwr_ctrl,
+ S5P_VA_L2CC + L2X0_POWER_CTRL);
+
+ clean_dcache_area(&l2x0_regs_phys, sizeof(unsigned long));
+ clean_dcache_area(&l2x0_saved_regs, sizeof(struct l2x0_regs));
+ }
+
+ l2x0_init(S5P_VA_L2CC, L2_AUX_VAL, L2_AUX_MASK);
return 0;
}
diff --git a/arch/arm/mach-exynos/cpuidle.c b/arch/arm/mach-exynos/cpuidle.c
index 4ebb382..33ab4e7 100644
--- a/arch/arm/mach-exynos/cpuidle.c
+++ b/arch/arm/mach-exynos/cpuidle.c
@@ -11,25 +11,53 @@
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/cpuidle.h>
+#include <linux/cpu_pm.h>
#include <linux/io.h>
#include <linux/export.h>
#include <linux/time.h>
#include <asm/proc-fns.h>
+#include <asm/smp_scu.h>
+#include <asm/suspend.h>
+#include <asm/unified.h>
+#include <mach/regs-pmu.h>
+#include <mach/pmu.h>
+
+#include <plat/cpu.h>
+
+#define REG_DIRECTGO_ADDR (samsung_rev() == EXYNOS4210_REV_1_1 ? \
+ S5P_INFORM7 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \
+ (S5P_VA_SYSRAM + 0x24) : S5P_INFORM0))
+#define REG_DIRECTGO_FLAG (samsung_rev() == EXYNOS4210_REV_1_1 ? \
+ S5P_INFORM6 : (samsung_rev() == EXYNOS4210_REV_1_0 ? \
+ (S5P_VA_SYSRAM + 0x20) : S5P_INFORM1))
+
+#define S5P_CHECK_AFTR 0xFCBA0D10
static int exynos4_enter_idle(struct cpuidle_device *dev,
struct cpuidle_driver *drv,
int index);
+static int exynos4_enter_lowpower(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv,
+ int index);
-static struct cpuidle_state exynos4_cpuidle_set[] = {
+static struct cpuidle_state exynos4_cpuidle_set[] __initdata = {
[0] = {
.enter = exynos4_enter_idle,
.exit_latency = 1,
.target_residency = 100000,
.flags = CPUIDLE_FLAG_TIME_VALID,
- .name = "IDLE",
+ .name = "C0",
.desc = "ARM clock gating(WFI)",
},
+ [1] = {
+ .enter = exynos4_enter_lowpower,
+ .exit_latency = 300,
+ .target_residency = 100000,
+ .flags = CPUIDLE_FLAG_TIME_VALID,
+ .name = "C1",
+ .desc = "ARM power down",
+ },
};
static DEFINE_PER_CPU(struct cpuidle_device, exynos4_cpuidle_device);
@@ -39,9 +67,102 @@
.owner = THIS_MODULE,
};
+/* Ext-GIC nIRQ/nFIQ is the only wakeup source in AFTR */
+static void exynos4_set_wakeupmask(void)
+{
+ __raw_writel(0x0000ff3e, S5P_WAKEUP_MASK);
+}
+
+static unsigned int g_pwr_ctrl, g_diag_reg;
+
+static void save_cpu_arch_register(void)
+{
+ /*read power control register*/
+ asm("mrc p15, 0, %0, c15, c0, 0" : "=r"(g_pwr_ctrl) : : "cc");
+ /*read diagnostic register*/
+ asm("mrc p15, 0, %0, c15, c0, 1" : "=r"(g_diag_reg) : : "cc");
+ return;
+}
+
+static void restore_cpu_arch_register(void)
+{
+ /*write power control register*/
+ asm("mcr p15, 0, %0, c15, c0, 0" : : "r"(g_pwr_ctrl) : "cc");
+ /*write diagnostic register*/
+ asm("mcr p15, 0, %0, c15, c0, 1" : : "r"(g_diag_reg) : "cc");
+ return;
+}
+
+static int idle_finisher(unsigned long flags)
+{
+ cpu_do_idle();
+ return 1;
+}
+
+static int exynos4_enter_core0_aftr(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv,
+ int index)
+{
+ struct timeval before, after;
+ int idle_time;
+ unsigned long tmp;
+
+ local_irq_disable();
+ do_gettimeofday(&before);
+
+ exynos4_set_wakeupmask();
+
+ /* Set value of power down register for aftr mode */
+ exynos4_sys_powerdown_conf(SYS_AFTR);
+
+ __raw_writel(virt_to_phys(s3c_cpu_resume), REG_DIRECTGO_ADDR);
+ __raw_writel(S5P_CHECK_AFTR, REG_DIRECTGO_FLAG);
+
+ save_cpu_arch_register();
+
+ /* Setting Central Sequence Register for power down mode */
+ tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
+ tmp &= ~S5P_CENTRAL_LOWPWR_CFG;
+ __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
+
+ cpu_pm_enter();
+ cpu_suspend(0, idle_finisher);
+
+#ifdef CONFIG_SMP
+ scu_enable(S5P_VA_SCU);
+#endif
+ cpu_pm_exit();
+
+ restore_cpu_arch_register();
+
+ /*
+ * If PMU failed while entering sleep mode, WFI will be
+ * ignored by PMU and then exiting cpu_do_idle().
+ * S5P_CENTRAL_LOWPWR_CFG bit will not be set automatically
+ * in this situation.
+ */
+ tmp = __raw_readl(S5P_CENTRAL_SEQ_CONFIGURATION);
+ if (!(tmp & S5P_CENTRAL_LOWPWR_CFG)) {
+ tmp |= S5P_CENTRAL_LOWPWR_CFG;
+ __raw_writel(tmp, S5P_CENTRAL_SEQ_CONFIGURATION);
+ }
+
+ /* Clear wakeup state register */
+ __raw_writel(0x0, S5P_WAKEUP_STAT);
+
+ do_gettimeofday(&after);
+
+ local_irq_enable();
+ idle_time = (after.tv_sec - before.tv_sec) * USEC_PER_SEC +
+ (after.tv_usec - before.tv_usec);
+
+ dev->last_residency = idle_time;
+ return index;
+}
+
static int exynos4_enter_idle(struct cpuidle_device *dev,
struct cpuidle_driver *drv,
- int index)
+ int index)
{
struct timeval before, after;
int idle_time;
@@ -60,6 +181,22 @@
return index;
}
+static int exynos4_enter_lowpower(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv,
+ int index)
+{
+ int new_index = index;
+
+ /* This mode only can be entered when other core's are offline */
+ if (num_online_cpus() > 1)
+ new_index = drv->safe_state_index;
+
+ if (new_index == 0)
+ return exynos4_enter_idle(dev, drv, new_index);
+ else
+ return exynos4_enter_core0_aftr(dev, drv, new_index);
+}
+
static int __init exynos4_init_cpuidle(void)
{
int i, max_cpuidle_state, cpu_id;
@@ -74,19 +211,25 @@
memcpy(&drv->states[i], &exynos4_cpuidle_set[i],
sizeof(struct cpuidle_state));
}
+ drv->safe_state_index = 0;
cpuidle_register_driver(&exynos4_idle_driver);
for_each_cpu(cpu_id, cpu_online_mask) {
device = &per_cpu(exynos4_cpuidle_device, cpu_id);
device->cpu = cpu_id;
- device->state_count = drv->state_count;
+ if (cpu_id == 0)
+ device->state_count = (sizeof(exynos4_cpuidle_set) /
+ sizeof(struct cpuidle_state));
+ else
+ device->state_count = 1; /* Support IDLE only */
if (cpuidle_register_device(device)) {
printk(KERN_ERR "CPUidle register device failed\n,");
return -EIO;
}
}
+
return 0;
}
device_initcall(exynos4_init_cpuidle);
diff --git a/arch/arm/mach-exynos/include/mach/map.h b/arch/arm/mach-exynos/include/mach/map.h
index c754a22..a8cd65f 100644
--- a/arch/arm/mach-exynos/include/mach/map.h
+++ b/arch/arm/mach-exynos/include/mach/map.h
@@ -31,6 +31,10 @@
#define EXYNOS4_PA_FIMC2 0x11820000
#define EXYNOS4_PA_FIMC3 0x11830000
+#define EXYNOS4_PA_JPEG 0x11840000
+
+#define EXYNOS4_PA_G2D 0x12800000
+
#define EXYNOS4_PA_I2S0 0x03830000
#define EXYNOS4_PA_I2S1 0xE3100000
#define EXYNOS4_PA_I2S2 0xE2A00000
@@ -57,6 +61,7 @@
#define EXYNOS4_PA_KEYPAD 0x100A0000
#define EXYNOS4_PA_DMC0 0x10400000
+#define EXYNOS4_PA_DMC1 0x10410000
#define EXYNOS4_PA_COMBINER 0x10440000
@@ -162,6 +167,8 @@
#define S5P_PA_FIMC1 EXYNOS4_PA_FIMC1
#define S5P_PA_FIMC2 EXYNOS4_PA_FIMC2
#define S5P_PA_FIMC3 EXYNOS4_PA_FIMC3
+#define S5P_PA_JPEG EXYNOS4_PA_JPEG
+#define S5P_PA_G2D EXYNOS4_PA_G2D
#define S5P_PA_FIMD0 EXYNOS4_PA_FIMD0
#define S5P_PA_HDMI EXYNOS4_PA_HDMI
#define S5P_PA_IIC_HDMIPHY EXYNOS4_PA_IIC_HDMIPHY
diff --git a/arch/arm/mach-exynos/include/mach/pmu.h b/arch/arm/mach-exynos/include/mach/pmu.h
index 632dd56..e76b7fa 100644
--- a/arch/arm/mach-exynos/include/mach/pmu.h
+++ b/arch/arm/mach-exynos/include/mach/pmu.h
@@ -22,11 +22,13 @@
NUM_SYS_POWERDOWN,
};
+extern unsigned long l2x0_regs_phys;
struct exynos4_pmu_conf {
void __iomem *reg;
unsigned int val[NUM_SYS_POWERDOWN];
};
extern void exynos4_sys_powerdown_conf(enum sys_powerdown mode);
+extern void s3c_cpu_resume(void);
#endif /* __ASM_ARCH_PMU_H */
diff --git a/arch/arm/mach-exynos/mct.c b/arch/arm/mach-exynos/mct.c
index 85b5527..3e894ba 100644
--- a/arch/arm/mach-exynos/mct.c
+++ b/arch/arm/mach-exynos/mct.c
@@ -29,12 +29,13 @@
#include <mach/regs-mct.h>
#include <asm/mach/time.h>
+#define TICK_BASE_CNT 1
+
enum {
MCT_INT_SPI,
MCT_INT_PPI
};
-static unsigned long clk_cnt_per_tick;
static unsigned long clk_rate;
static unsigned int mct_int_type;
@@ -205,11 +206,14 @@
static void exynos4_comp_set_mode(enum clock_event_mode mode,
struct clock_event_device *evt)
{
+ unsigned long cycles_per_jiffy;
exynos4_mct_comp0_stop();
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
- exynos4_mct_comp0_start(mode, clk_cnt_per_tick);
+ cycles_per_jiffy =
+ (((unsigned long long) NSEC_PER_SEC / HZ * evt->mult) >> evt->shift);
+ exynos4_mct_comp0_start(mode, cycles_per_jiffy);
break;
case CLOCK_EVT_MODE_ONESHOT:
@@ -248,9 +252,7 @@
static void exynos4_clockevent_init(void)
{
- clk_cnt_per_tick = clk_rate / 2 / HZ;
-
- clockevents_calc_mult_shift(&mct_comp_device, clk_rate / 2, 5);
+ clockevents_calc_mult_shift(&mct_comp_device, clk_rate, 5);
mct_comp_device.max_delta_ns =
clockevent_delta2ns(0xffffffff, &mct_comp_device);
mct_comp_device.min_delta_ns =
@@ -314,12 +316,15 @@
struct clock_event_device *evt)
{
struct mct_clock_event_device *mevt = this_cpu_ptr(&percpu_mct_tick);
+ unsigned long cycles_per_jiffy;
exynos4_mct_tick_stop(mevt);
switch (mode) {
case CLOCK_EVT_MODE_PERIODIC:
- exynos4_mct_tick_start(clk_cnt_per_tick, mevt);
+ cycles_per_jiffy =
+ (((unsigned long long) NSEC_PER_SEC / HZ * evt->mult) >> evt->shift);
+ exynos4_mct_tick_start(cycles_per_jiffy, mevt);
break;
case CLOCK_EVT_MODE_ONESHOT:
@@ -393,7 +398,7 @@
evt->features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT;
evt->rating = 450;
- clockevents_calc_mult_shift(evt, clk_rate / 2, 5);
+ clockevents_calc_mult_shift(evt, clk_rate / (TICK_BASE_CNT + 1), 5);
evt->max_delta_ns =
clockevent_delta2ns(0x7fffffff, evt);
evt->min_delta_ns =
@@ -401,7 +406,7 @@
clockevents_register_device(evt);
- exynos4_mct_write(0x1, mevt->base + MCT_L_TCNTB_OFFSET);
+ exynos4_mct_write(TICK_BASE_CNT, mevt->base + MCT_L_TCNTB_OFFSET);
if (mct_int_type == MCT_INT_SPI) {
if (cpu == 0) {
diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c
index e190130..4816827 100644
--- a/arch/arm/mach-exynos/pm.c
+++ b/arch/arm/mach-exynos/pm.c
@@ -155,13 +155,6 @@
SAVE_ITEM(S5P_SROM_BC3),
};
-static struct sleep_save exynos4_l2cc_save[] = {
- SAVE_ITEM(S5P_VA_L2CC + L2X0_TAG_LATENCY_CTRL),
- SAVE_ITEM(S5P_VA_L2CC + L2X0_DATA_LATENCY_CTRL),
- SAVE_ITEM(S5P_VA_L2CC + L2X0_PREFETCH_CTRL),
- SAVE_ITEM(S5P_VA_L2CC + L2X0_POWER_CTRL),
- SAVE_ITEM(S5P_VA_L2CC + L2X0_AUX_CTRL),
-};
/* For Cortex-A9 Diagnostic and Power control register */
static unsigned int save_arm_register[2];
@@ -182,7 +175,6 @@
u32 tmp;
s3c_pm_do_save(exynos4_core_save, ARRAY_SIZE(exynos4_core_save));
- s3c_pm_do_save(exynos4_l2cc_save, ARRAY_SIZE(exynos4_l2cc_save));
s3c_pm_do_save(exynos4_epll_save, ARRAY_SIZE(exynos4_epll_save));
s3c_pm_do_save(exynos4_vpll_save, ARRAY_SIZE(exynos4_vpll_save));
@@ -388,13 +380,6 @@
scu_enable(S5P_VA_SCU);
#endif
-#ifdef CONFIG_CACHE_L2X0
- s3c_pm_do_restore_core(exynos4_l2cc_save, ARRAY_SIZE(exynos4_l2cc_save));
- outer_inv_all();
- /* enable L2X0*/
- writel_relaxed(1, S5P_VA_L2CC + L2X0_CTRL);
-#endif
-
early_wakeup:
return;
}
diff --git a/arch/arm/mach-s3c64xx/Kconfig b/arch/arm/mach-s3c64xx/Kconfig
index dd20c66..326ea3a 100644
--- a/arch/arm/mach-s3c64xx/Kconfig
+++ b/arch/arm/mach-s3c64xx/Kconfig
@@ -83,6 +83,11 @@
help
Common setup code for SPI GPIO configurations
+config S3C64XX_SETUP_USB_PHY
+ bool
+ help
+ Common setup code for USB PHY controller
+
# S36400 Macchine support
config MACH_SMDK6400
@@ -157,6 +162,7 @@
select S3C64XX_SETUP_IDE
select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_KEYPAD
+ select S3C64XX_SETUP_USB_PHY
help
Machine support for the Samsung SMDK6410
@@ -256,6 +262,7 @@
select S3C_DEV_USB_HOST
select S3C64XX_SETUP_SDHCI
select S3C64XX_SETUP_FB_24BPP
+ select S3C64XX_SETUP_USB_PHY
select SAMSUNG_DEV_ADC
select SAMSUNG_DEV_PWM
select SAMSUNG_DEV_TS
@@ -283,6 +290,7 @@
select S3C64XX_SETUP_FB_24BPP
select S3C64XX_SETUP_KEYPAD
select S3C64XX_SETUP_SPI
+ select S3C64XX_SETUP_USB_PHY
select SAMSUNG_DEV_ADC
select SAMSUNG_DEV_KEYPAD
select S3C_DEV_USB_HOST
diff --git a/arch/arm/mach-s3c64xx/Makefile b/arch/arm/mach-s3c64xx/Makefile
index 1822ac2..f9ce1dc 100644
--- a/arch/arm/mach-s3c64xx/Makefile
+++ b/arch/arm/mach-s3c64xx/Makefile
@@ -22,6 +22,7 @@
# PM
obj-$(CONFIG_PM) += pm.o irq-pm.o sleep.o
+obj-$(CONFIG_CPU_IDLE) += cpuidle.o
# DMA support
@@ -42,6 +43,7 @@
obj-$(CONFIG_S3C64XX_SETUP_KEYPAD) += setup-keypad.o
obj-$(CONFIG_S3C64XX_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
obj-$(CONFIG_S3C64XX_SETUP_SPI) += setup-spi.o
+obj-$(CONFIG_S3C64XX_SETUP_USB_PHY) += setup-usb-phy.o
# Machine support
diff --git a/arch/arm/mach-s3c64xx/clock.c b/arch/arm/mach-s3c64xx/clock.c
index aebbcc2..52f079a 100644
--- a/arch/arm/mach-s3c64xx/clock.c
+++ b/arch/arm/mach-s3c64xx/clock.c
@@ -207,6 +207,15 @@
.enable = s3c64xx_sclk_ctrl,
.ctrlbit = S3C_CLKCON_SCLK_MMC2_48,
}, {
+ .name = "ac97",
+ .parent = &clk_p,
+ .ctrlbit = S3C_CLKCON_PCLK_AC97,
+ }, {
+ .name = "cfcon",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_IHOST,
+ }, {
.name = "dma0",
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
@@ -216,6 +225,107 @@
.parent = &clk_h,
.enable = s3c64xx_hclk_ctrl,
.ctrlbit = S3C_CLKCON_HCLK_DMA1,
+ }, {
+ .name = "3dse",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_3DSE,
+ }, {
+ .name = "hclk_secur",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_SECUR,
+ }, {
+ .name = "sdma1",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_SDMA1,
+ }, {
+ .name = "sdma0",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_SDMA0,
+ }, {
+ .name = "hclk_jpeg",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_JPEG,
+ }, {
+ .name = "camif",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_CAMIF,
+ }, {
+ .name = "hclk_scaler",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_SCALER,
+ }, {
+ .name = "2d",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_2D,
+ }, {
+ .name = "tv",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_TV,
+ }, {
+ .name = "post0",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_POST0,
+ }, {
+ .name = "rot",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_ROT,
+ }, {
+ .name = "hclk_mfc",
+ .parent = &clk_h,
+ .enable = s3c64xx_hclk_ctrl,
+ .ctrlbit = S3C_CLKCON_HCLK_MFC,
+ }, {
+ .name = "pclk_mfc",
+ .parent = &clk_p,
+ .enable = s3c64xx_pclk_ctrl,
+ .ctrlbit = S3C_CLKCON_PCLK_MFC,
+ }, {
+ .name = "dac27",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_DAC27,
+ }, {
+ .name = "tv27",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_TV27,
+ }, {
+ .name = "scaler27",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_SCALER27,
+ }, {
+ .name = "sclk_scaler",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_SCALER,
+ }, {
+ .name = "post0_27",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_POST0_27,
+ }, {
+ .name = "secur",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_SECUR,
+ }, {
+ .name = "sclk_mfc",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_MFC,
+ }, {
+ .name = "cam",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_CAM,
+ }, {
+ .name = "sclk_jpeg",
+ .enable = s3c64xx_sclk_ctrl,
+ .ctrlbit = S3C_CLKCON_SCLK_JPEG,
},
};
@@ -289,16 +399,7 @@
.name = "watchdog",
.parent = &clk_p,
.ctrlbit = S3C_CLKCON_PCLK_WDT,
- }, {
- .name = "ac97",
- .parent = &clk_p,
- .ctrlbit = S3C_CLKCON_PCLK_AC97,
- }, {
- .name = "cfcon",
- .parent = &clk_h,
- .enable = s3c64xx_hclk_ctrl,
- .ctrlbit = S3C_CLKCON_HCLK_IHOST,
- }
+ },
};
static struct clk clk_hsmmc0 = {
diff --git a/arch/arm/mach-s3c64xx/cpuidle.c b/arch/arm/mach-s3c64xx/cpuidle.c
new file mode 100644
index 0000000..179460f
--- /dev/null
+++ b/arch/arm/mach-s3c64xx/cpuidle.c
@@ -0,0 +1,91 @@
+/* linux/arch/arm/mach-s3c64xx/cpuidle.c
+ *
+ * Copyright (c) 2011 Wolfson Microelectronics, plc
+ * Copyright (c) 2011 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/cpuidle.h>
+#include <linux/io.h>
+#include <linux/export.h>
+#include <linux/time.h>
+
+#include <asm/proc-fns.h>
+
+#include <mach/map.h>
+
+#include <mach/regs-sys.h>
+#include <mach/regs-syscon-power.h>
+
+static int s3c64xx_enter_idle(struct cpuidle_device *dev,
+ struct cpuidle_driver *drv,
+ int index)
+{
+ struct timeval before, after;
+ unsigned long tmp;
+ int idle_time;
+
+ local_irq_disable();
+ do_gettimeofday(&before);
+
+ /* Setup PWRCFG to enter idle mode */
+ tmp = __raw_readl(S3C64XX_PWR_CFG);
+ tmp &= ~S3C64XX_PWRCFG_CFG_WFI_MASK;
+ tmp |= S3C64XX_PWRCFG_CFG_WFI_IDLE;
+ __raw_writel(tmp, S3C64XX_PWR_CFG);
+
+ cpu_do_idle();
+
+ do_gettimeofday(&after);
+ local_irq_enable();
+ idle_time = (after.tv_sec - before.tv_sec) * USEC_PER_SEC +
+ (after.tv_usec - before.tv_usec);
+
+ dev->last_residency = idle_time;
+ return index;
+}
+
+static struct cpuidle_state s3c64xx_cpuidle_set[] = {
+ [0] = {
+ .enter = s3c64xx_enter_idle,
+ .exit_latency = 1,
+ .target_residency = 1,
+ .flags = CPUIDLE_FLAG_TIME_VALID,
+ .name = "IDLE",
+ .desc = "System active, ARM gated",
+ },
+};
+
+static struct cpuidle_driver s3c64xx_cpuidle_driver = {
+ .name = "s3c64xx_cpuidle",
+ .owner = THIS_MODULE,
+ .state_count = ARRAY_SIZE(s3c64xx_cpuidle_set),
+};
+
+static struct cpuidle_device s3c64xx_cpuidle_device = {
+ .state_count = ARRAY_SIZE(s3c64xx_cpuidle_set),
+};
+
+static int __init s3c64xx_init_cpuidle(void)
+{
+ int ret;
+
+ memcpy(s3c64xx_cpuidle_driver.states, s3c64xx_cpuidle_set,
+ sizeof(s3c64xx_cpuidle_set));
+ cpuidle_register_driver(&s3c64xx_cpuidle_driver);
+
+ ret = cpuidle_register_device(&s3c64xx_cpuidle_device);
+ if (ret) {
+ pr_err("Failed to register cpuidle device: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+device_initcall(s3c64xx_init_cpuidle);
diff --git a/arch/arm/mach-s3c64xx/mach-crag6410.c b/arch/arm/mach-s3c64xx/mach-crag6410.c
index 8077f65..3b56bd9 100644
--- a/arch/arm/mach-s3c64xx/mach-crag6410.c
+++ b/arch/arm/mach-s3c64xx/mach-crag6410.c
@@ -59,6 +59,7 @@
#include <plat/sdhci.h>
#include <plat/gpio-cfg.h>
#include <plat/s3c64xx-spi.h>
+#include <plat/udc-hs.h>
#include <plat/keypad.h>
#include <plat/clock.h>
@@ -698,6 +699,8 @@
.cfg_gpio = crag6410_cfg_sdhci0,
};
+static struct s3c_hsotg_plat crag6410_hsotg_pdata;
+
static void __init crag6410_machine_init(void)
{
/* Open drain IRQs need pullups */
@@ -722,6 +725,7 @@
s3c_i2c0_set_platdata(&i2c0_pdata);
s3c_i2c1_set_platdata(&i2c1_pdata);
s3c_fb_set_platdata(&crag6410_lcd_pdata);
+ s3c_hsotg_set_platdata(&crag6410_hsotg_pdata);
i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
diff --git a/arch/arm/mach-s3c64xx/mach-smartq.c b/arch/arm/mach-s3c64xx/mach-smartq.c
index ce31db1..ce745e1 100644
--- a/arch/arm/mach-s3c64xx/mach-smartq.c
+++ b/arch/arm/mach-s3c64xx/mach-smartq.c
@@ -187,6 +187,8 @@
},
};
+static struct s3c_hsotg_plat smartq_hsotg_pdata;
+
static int __init smartq_lcd_setup_gpio(void)
{
int ret;
@@ -383,6 +385,7 @@
void __init smartq_machine_init(void)
{
s3c_i2c0_set_platdata(NULL);
+ s3c_hsotg_set_platdata(&smartq_hsotg_pdata);
s3c_hwmon_set_platdata(&smartq_hwmon_pdata);
s3c_sdhci1_set_platdata(&smartq_internal_hsmmc_pdata);
s3c_sdhci2_set_platdata(&smartq_internal_hsmmc_pdata);
diff --git a/arch/arm/mach-s3c64xx/mach-smdk6410.c b/arch/arm/mach-s3c64xx/mach-smdk6410.c
index ca6fc20..d55bc96 100644
--- a/arch/arm/mach-s3c64xx/mach-smdk6410.c
+++ b/arch/arm/mach-s3c64xx/mach-smdk6410.c
@@ -72,6 +72,7 @@
#include <plat/keypad.h>
#include <plat/backlight.h>
#include <plat/regs-fb-v4.h>
+#include <plat/udc-hs.h>
#include "common.h"
@@ -631,6 +632,8 @@
.pwm_id = 1,
};
+static struct s3c_hsotg_plat smdk6410_hsotg_pdata;
+
static void __init smdk6410_map_io(void)
{
u32 tmp;
@@ -659,6 +662,7 @@
s3c_i2c0_set_platdata(NULL);
s3c_i2c1_set_platdata(NULL);
s3c_fb_set_platdata(&smdk6410_lcd_pdata);
+ s3c_hsotg_set_platdata(&smdk6410_hsotg_pdata);
samsung_keypad_set_platdata(&smdk6410_keypad_data);
diff --git a/arch/arm/mach-s3c64xx/setup-usb-phy.c b/arch/arm/mach-s3c64xx/setup-usb-phy.c
new file mode 100644
index 0000000..f6757e0
--- /dev/null
+++ b/arch/arm/mach-s3c64xx/setup-usb-phy.c
@@ -0,0 +1,90 @@
+/*
+ * Copyright (C) 2011 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <mach/map.h>
+#include <mach/regs-sys.h>
+#include <plat/cpu.h>
+#include <plat/regs-usb-hsotg-phy.h>
+#include <plat/usb-phy.h>
+
+static int s3c_usb_otgphy_init(struct platform_device *pdev)
+{
+ struct clk *xusbxti;
+ u32 phyclk;
+
+ writel(readl(S3C64XX_OTHERS) | S3C64XX_OTHERS_USBMASK, S3C64XX_OTHERS);
+
+ /* set clock frequency for PLL */
+ phyclk = readl(S3C_PHYCLK) & ~S3C_PHYCLK_CLKSEL_MASK;
+
+ xusbxti = clk_get(&pdev->dev, "xusbxti");
+ if (xusbxti && !IS_ERR(xusbxti)) {
+ switch (clk_get_rate(xusbxti)) {
+ case 12 * MHZ:
+ phyclk |= S3C_PHYCLK_CLKSEL_12M;
+ break;
+ case 24 * MHZ:
+ phyclk |= S3C_PHYCLK_CLKSEL_24M;
+ break;
+ default:
+ case 48 * MHZ:
+ /* default reference clock */
+ break;
+ }
+ clk_put(xusbxti);
+ }
+
+ /* TODO: select external clock/oscillator */
+ writel(phyclk | S3C_PHYCLK_CLK_FORCE, S3C_PHYCLK);
+
+ /* set to normal OTG PHY */
+ writel((readl(S3C_PHYPWR) & ~S3C_PHYPWR_NORMAL_MASK), S3C_PHYPWR);
+ mdelay(1);
+
+ /* reset OTG PHY and Link */
+ writel(S3C_RSTCON_PHY | S3C_RSTCON_HCLK | S3C_RSTCON_PHYCLK,
+ S3C_RSTCON);
+ udelay(20); /* at-least 10uS */
+ writel(0, S3C_RSTCON);
+
+ return 0;
+}
+
+static int s3c_usb_otgphy_exit(struct platform_device *pdev)
+{
+ writel((readl(S3C_PHYPWR) | S3C_PHYPWR_ANALOG_POWERDOWN |
+ S3C_PHYPWR_OTG_DISABLE), S3C_PHYPWR);
+
+ writel(readl(S3C64XX_OTHERS) & ~S3C64XX_OTHERS_USBMASK, S3C64XX_OTHERS);
+
+ return 0;
+}
+
+int s5p_usb_phy_init(struct platform_device *pdev, int type)
+{
+ if (type == S5P_USB_PHY_DEVICE)
+ return s3c_usb_otgphy_init(pdev);
+
+ return -EINVAL;
+}
+
+int s5p_usb_phy_exit(struct platform_device *pdev, int type)
+{
+ if (type == S5P_USB_PHY_DEVICE)
+ return s3c_usb_otgphy_exit(pdev);
+
+ return -EINVAL;
+}
diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 2cdc42e..82525e3 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -65,6 +65,11 @@
help
Common setup code for SPI GPIO configurations.
+config S5PV210_SETUP_USB_PHY
+ bool
+ help
+ Common setup code for USB PHY controller
+
menu "S5PC110 Machines"
config MACH_AQUILA
@@ -107,6 +112,7 @@
select S5PV210_SETUP_KEYPAD
select S5PV210_SETUP_SDHCI
select S5PV210_SETUP_FIMC
+ select S5PV210_SETUP_USB_PHY
help
Machine support for Samsung GONI board
S5PC110(MCP) is one of package option of S5PV210
diff --git a/arch/arm/mach-s5pv210/Makefile b/arch/arm/mach-s5pv210/Makefile
index 76a121d..1c4e419 100644
--- a/arch/arm/mach-s5pv210/Makefile
+++ b/arch/arm/mach-s5pv210/Makefile
@@ -39,3 +39,4 @@
obj-$(CONFIG_S5PV210_SETUP_KEYPAD) += setup-keypad.o
obj-$(CONFIG_S5PV210_SETUP_SDHCI_GPIO) += setup-sdhci-gpio.o
obj-$(CONFIG_S5PV210_SETUP_SPI) += setup-spi.o
+obj-$(CONFIG_S5PV210_SETUP_USB_PHY) += setup-usb-phy.o
diff --git a/arch/arm/mach-s5pv210/include/mach/regs-sys.h b/arch/arm/mach-s5pv210/include/mach/regs-sys.h
index 26691d3..cccb1ed 100644
--- a/arch/arm/mach-s5pv210/include/mach/regs-sys.h
+++ b/arch/arm/mach-s5pv210/include/mach/regs-sys.h
@@ -13,7 +13,3 @@
#define S5PV210_USB_PHY_CON (S3C_VA_SYS + 0xE80C)
#define S5PV210_USB_PHY0_EN (1 << 0)
#define S5PV210_USB_PHY1_EN (1 << 1)
-
-/* compatibility defines for s3c-hsotg driver */
-#define S3C64XX_OTHERS S5PV210_USB_PHY_CON
-#define S3C64XX_OTHERS_USBMASK S5PV210_USB_PHY0_EN
diff --git a/arch/arm/mach-s5pv210/setup-usb-phy.c b/arch/arm/mach-s5pv210/setup-usb-phy.c
new file mode 100644
index 0000000..be39cf4
--- /dev/null
+++ b/arch/arm/mach-s5pv210/setup-usb-phy.c
@@ -0,0 +1,90 @@
+/*
+ * Copyright (C) 2012 Samsung Electronics Co.Ltd
+ * Author: Joonyoung Shim <jy0922.shim@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundationr
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <mach/map.h>
+#include <mach/regs-sys.h>
+#include <plat/cpu.h>
+#include <plat/regs-usb-hsotg-phy.h>
+#include <plat/usb-phy.h>
+
+static int s5pv210_usb_otgphy_init(struct platform_device *pdev)
+{
+ struct clk *xusbxti;
+ u32 phyclk;
+
+ writel(readl(S5PV210_USB_PHY_CON) | S5PV210_USB_PHY0_EN,
+ S5PV210_USB_PHY_CON);
+
+ /* set clock frequency for PLL */
+ phyclk = readl(S3C_PHYCLK) & ~S3C_PHYCLK_CLKSEL_MASK;
+
+ xusbxti = clk_get(&pdev->dev, "xusbxti");
+ if (xusbxti && !IS_ERR(xusbxti)) {
+ switch (clk_get_rate(xusbxti)) {
+ case 12 * MHZ:
+ phyclk |= S3C_PHYCLK_CLKSEL_12M;
+ break;
+ case 24 * MHZ:
+ phyclk |= S3C_PHYCLK_CLKSEL_24M;
+ break;
+ default:
+ case 48 * MHZ:
+ /* default reference clock */
+ break;
+ }
+ clk_put(xusbxti);
+ }
+
+ /* TODO: select external clock/oscillator */
+ writel(phyclk | S3C_PHYCLK_CLK_FORCE, S3C_PHYCLK);
+
+ /* set to normal OTG PHY */
+ writel((readl(S3C_PHYPWR) & ~S3C_PHYPWR_NORMAL_MASK), S3C_PHYPWR);
+ mdelay(1);
+
+ /* reset OTG PHY and Link */
+ writel(S3C_RSTCON_PHY | S3C_RSTCON_HCLK | S3C_RSTCON_PHYCLK,
+ S3C_RSTCON);
+ udelay(20); /* at-least 10uS */
+ writel(0, S3C_RSTCON);
+
+ return 0;
+}
+
+static int s5pv210_usb_otgphy_exit(struct platform_device *pdev)
+{
+ writel((readl(S3C_PHYPWR) | S3C_PHYPWR_ANALOG_POWERDOWN |
+ S3C_PHYPWR_OTG_DISABLE), S3C_PHYPWR);
+
+ writel(readl(S5PV210_USB_PHY_CON) & ~S5PV210_USB_PHY0_EN,
+ S5PV210_USB_PHY_CON);
+
+ return 0;
+}
+
+int s5p_usb_phy_init(struct platform_device *pdev, int type)
+{
+ if (type == S5P_USB_PHY_DEVICE)
+ return s5pv210_usb_otgphy_init(pdev);
+
+ return -EINVAL;
+}
+
+int s5p_usb_phy_exit(struct platform_device *pdev, int type)
+{
+ if (type == S5P_USB_PHY_DEVICE)
+ return s5pv210_usb_otgphy_exit(pdev);
+
+ return -EINVAL;
+}
diff --git a/arch/arm/plat-s5p/Kconfig b/arch/arm/plat-s5p/Kconfig
index 8167ce6..7a30869 100644
--- a/arch/arm/plat-s5p/Kconfig
+++ b/arch/arm/plat-s5p/Kconfig
@@ -80,6 +80,16 @@
help
Compile in platform device definitions for FIMC controller 3
+config S5P_DEV_JPEG
+ bool
+ help
+ Compile in platform device definitions for JPEG codec
+
+config S5P_DEV_G2D
+ bool
+ help
+ Compile in platform device definitions for G2D device
+
config S5P_DEV_FIMD0
bool
help
diff --git a/arch/arm/plat-s5p/sleep.S b/arch/arm/plat-s5p/sleep.S
index 0fd591b..006bd01 100644
--- a/arch/arm/plat-s5p/sleep.S
+++ b/arch/arm/plat-s5p/sleep.S
@@ -23,9 +23,18 @@
*/
#include <linux/linkage.h>
-#include <asm/assembler.h>
+#include <asm/asm-offsets.h>
+#include <asm/hardware/cache-l2x0.h>
- .text
+/*
+ * The following code is located into the .data section. This is to
+ * allow l2x0_regs_phys to be accessed with a relative load while we
+ * can't rely on any MMU translation. We could have put l2x0_regs_phys
+ * in the .text section as well, but some setups might insist on it to
+ * be truly read-only. (Reference from: arch/arm/kernel/sleep.S)
+ */
+ .data
+ .align
/*
* sleep magic, to allow the bootloader to check for an valid
@@ -39,11 +48,34 @@
* s3c_cpu_resume
*
* resume code entry for bootloader to call
- *
- * we must put this code here in the data segment as we have no
- * other way of restoring the stack pointer after sleep, and we
- * must not write to the code segment (code is read-only)
*/
ENTRY(s3c_cpu_resume)
+#ifdef CONFIG_CACHE_L2X0
+ adr r0, l2x0_regs_phys
+ ldr r0, [r0]
+ ldr r1, [r0, #L2X0_R_PHY_BASE]
+ ldr r2, [r1, #L2X0_CTRL]
+ tst r2, #0x1
+ bne resume_l2on
+ ldr r2, [r0, #L2X0_R_AUX_CTRL]
+ str r2, [r1, #L2X0_AUX_CTRL]
+ ldr r2, [r0, #L2X0_R_TAG_LATENCY]
+ str r2, [r1, #L2X0_TAG_LATENCY_CTRL]
+ ldr r2, [r0, #L2X0_R_DATA_LATENCY]
+ str r2, [r1, #L2X0_DATA_LATENCY_CTRL]
+ ldr r2, [r0, #L2X0_R_PREFETCH_CTRL]
+ str r2, [r1, #L2X0_PREFETCH_CTRL]
+ ldr r2, [r0, #L2X0_R_PWR_CTRL]
+ str r2, [r1, #L2X0_POWER_CTRL]
+ mov r2, #1
+ str r2, [r1, #L2X0_CTRL]
+resume_l2on:
+#endif
b cpu_resume
+ENDPROC(s3c_cpu_resume)
+#ifdef CONFIG_CACHE_L2X0
+ .globl l2x0_regs_phys
+l2x0_regs_phys:
+ .long 0
+#endif
diff --git a/arch/arm/plat-samsung/clock.c b/arch/arm/plat-samsung/clock.c
index 10f7117..65c5eca 100644
--- a/arch/arm/plat-samsung/clock.c
+++ b/arch/arm/plat-samsung/clock.c
@@ -84,31 +84,35 @@
int clk_enable(struct clk *clk)
{
+ unsigned long flags;
+
if (IS_ERR(clk) || clk == NULL)
return -EINVAL;
clk_enable(clk->parent);
- spin_lock(&clocks_lock);
+ spin_lock_irqsave(&clocks_lock, flags);
if ((clk->usage++) == 0)
(clk->enable)(clk, 1);
- spin_unlock(&clocks_lock);
+ spin_unlock_irqrestore(&clocks_lock, flags);
return 0;
}
void clk_disable(struct clk *clk)
{
+ unsigned long flags;
+
if (IS_ERR(clk) || clk == NULL)
return;
- spin_lock(&clocks_lock);
+ spin_lock_irqsave(&clocks_lock, flags);
if ((--clk->usage) == 0)
(clk->enable)(clk, 0);
- spin_unlock(&clocks_lock);
+ spin_unlock_irqrestore(&clocks_lock, flags);
clk_disable(clk->parent);
}
diff --git a/arch/arm/plat-samsung/dev-backlight.c b/arch/arm/plat-samsung/dev-backlight.c
index a976c02..5f197dc 100644
--- a/arch/arm/plat-samsung/dev-backlight.c
+++ b/arch/arm/plat-samsung/dev-backlight.c
@@ -77,7 +77,7 @@
* @gpio_info: structure containing GPIO info for PWM timer
* @bl_data: structure containing Backlight control data
*/
-void samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
+void __init samsung_bl_set(struct samsung_bl_gpio_info *gpio_info,
struct platform_pwm_backlight_data *bl_data)
{
int ret = 0;
@@ -115,6 +115,8 @@
samsung_bl_data->init = bl_data->init;
if (bl_data->notify)
samsung_bl_data->notify = bl_data->notify;
+ if (bl_data->notify_after)
+ samsung_bl_data->notify_after = bl_data->notify_after;
if (bl_data->exit)
samsung_bl_data->exit = bl_data->exit;
if (bl_data->check_fb)
diff --git a/arch/arm/plat-samsung/devs.c b/arch/arm/plat-samsung/devs.c
index f10768e..eb3ba13 100644
--- a/arch/arm/plat-samsung/devs.c
+++ b/arch/arm/plat-samsung/devs.c
@@ -57,6 +57,7 @@
#include <plat/sdhci.h>
#include <plat/ts.h>
#include <plat/udc.h>
+#include <plat/udc-hs.h>
#include <plat/usb-control.h>
#include <plat/usb-phy.h>
#include <plat/regs-iic.h>
@@ -267,6 +268,52 @@
};
#endif /* CONFIG_S5P_DEV_FIMC3 */
+/* G2D */
+
+#ifdef CONFIG_S5P_DEV_G2D
+static struct resource s5p_g2d_resource[] = {
+ [0] = {
+ .start = S5P_PA_G2D,
+ .end = S5P_PA_G2D + SZ_4K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = IRQ_2D,
+ .end = IRQ_2D,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+struct platform_device s5p_device_g2d = {
+ .name = "s5p-g2d",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(s5p_g2d_resource),
+ .resource = s5p_g2d_resource,
+ .dev = {
+ .dma_mask = &samsung_device_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+#endif /* CONFIG_S5P_DEV_G2D */
+
+#ifdef CONFIG_S5P_DEV_JPEG
+static struct resource s5p_jpeg_resource[] = {
+ [0] = DEFINE_RES_MEM(S5P_PA_JPEG, SZ_4K),
+ [1] = DEFINE_RES_IRQ(IRQ_JPEG),
+};
+
+struct platform_device s5p_device_jpeg = {
+ .name = "s5p-jpeg",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(s5p_jpeg_resource),
+ .resource = s5p_jpeg_resource,
+ .dev = {
+ .dma_mask = &samsung_device_dma_mask,
+ .coherent_dma_mask = DMA_BIT_MASK(32),
+ },
+};
+#endif /* CONFIG_S5P_DEV_JPEG */
+
/* FIMD0 */
#ifdef CONFIG_S5P_DEV_FIMD0
@@ -769,7 +816,7 @@
.resource = s3c_cfcon_resource,
};
-void s3c_ide_set_platdata(struct s3c_ide_platdata *pdata)
+void __init s3c_ide_set_platdata(struct s3c_ide_platdata *pdata)
{
s3c_set_platdata(pdata, sizeof(struct s3c_ide_platdata),
&s3c_device_cfcon);
@@ -887,7 +934,7 @@
#ifdef CONFIG_S5P_DEV_CSIS0
static struct resource s5p_mipi_csis0_resource[] = {
- [0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS0, SZ_4K),
+ [0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS0, SZ_16K),
[1] = DEFINE_RES_IRQ(IRQ_MIPI_CSIS0),
};
@@ -901,7 +948,7 @@
#ifdef CONFIG_S5P_DEV_CSIS1
static struct resource s5p_mipi_csis1_resource[] = {
- [0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS1, SZ_4K),
+ [0] = DEFINE_RES_MEM(S5P_PA_MIPI_CSIS1, SZ_16K),
[1] = DEFINE_RES_IRQ(IRQ_MIPI_CSIS1),
};
@@ -1049,7 +1096,7 @@
.resource = s3c64xx_onenand1_resources,
};
-void s3c64xx_onenand1_set_platdata(struct onenand_platform_data *pdata)
+void __init s3c64xx_onenand1_set_platdata(struct onenand_platform_data *pdata)
{
s3c_set_platdata(pdata, sizeof(struct onenand_platform_data),
&s3c64xx_device_onenand1);
@@ -1423,6 +1470,19 @@
.coherent_dma_mask = DMA_BIT_MASK(32),
},
};
+
+void __init s3c_hsotg_set_platdata(struct s3c_hsotg_plat *pd)
+{
+ struct s3c_hsotg_plat *npd;
+
+ npd = s3c_set_platdata(pd, sizeof(struct s3c_hsotg_plat),
+ &s3c_device_usb_hsotg);
+
+ if (!npd->phy_init)
+ npd->phy_init = s5p_usb_phy_init;
+ if (!npd->phy_exit)
+ npd->phy_exit = s5p_usb_phy_exit;
+}
#endif /* CONFIG_S3C_DEV_USB_HSOTG */
/* USB High Spped 2.0 Device (Gadget) */
diff --git a/arch/arm/plat-samsung/include/plat/devs.h b/arch/arm/plat-samsung/include/plat/devs.h
index 4214ea0..5e7972d 100644
--- a/arch/arm/plat-samsung/include/plat/devs.h
+++ b/arch/arm/plat-samsung/include/plat/devs.h
@@ -79,6 +79,8 @@
extern struct platform_device s5p_device_fimc2;
extern struct platform_device s5p_device_fimc3;
extern struct platform_device s5p_device_fimc_md;
+extern struct platform_device s5p_device_jpeg;
+extern struct platform_device s5p_device_g2d;
extern struct platform_device s5p_device_fimd0;
extern struct platform_device s5p_device_hdmi;
extern struct platform_device s5p_device_i2c_hdmiphy;
diff --git a/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h
index a111ad8..fcf2796 100644
--- a/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h
+++ b/arch/arm/plat-samsung/include/plat/regs-usb-hsotg-phy.h
@@ -25,8 +25,9 @@
#define S3C_HSOTG_PHYREG(x) ((x) + S3C_VA_USB_HSPHY)
#define S3C_PHYPWR S3C_HSOTG_PHYREG(0x00)
-#define SRC_PHYPWR_OTG_DISABLE (1 << 4)
-#define SRC_PHYPWR_ANALOG_POWERDOWN (1 << 3)
+#define S3C_PHYPWR_NORMAL_MASK (0x19 << 0)
+#define S3C_PHYPWR_OTG_DISABLE (1 << 4)
+#define S3C_PHYPWR_ANALOG_POWERDOWN (1 << 3)
#define SRC_PHYPWR_FORCE_SUSPEND (1 << 1)
#define S3C_PHYCLK S3C_HSOTG_PHYREG(0x04)
@@ -42,7 +43,7 @@
#define S3C_RSTCON S3C_HSOTG_PHYREG(0x08)
#define S3C_RSTCON_PHYCLK (1 << 2)
-#define S3C_RSTCON_HCLK (1 << 2)
+#define S3C_RSTCON_HCLK (1 << 1)
#define S3C_RSTCON_PHY (1 << 0)
#define S3C_PHYTUNE S3C_HSOTG_PHYREG(0x20)
diff --git a/arch/arm/plat-samsung/include/plat/udc-hs.h b/arch/arm/plat-samsung/include/plat/udc-hs.h
index a22a4f2..c9e3667 100644
--- a/arch/arm/plat-samsung/include/plat/udc-hs.h
+++ b/arch/arm/plat-samsung/include/plat/udc-hs.h
@@ -26,4 +26,9 @@
struct s3c_hsotg_plat {
enum s3c_hsotg_dmamode dma;
unsigned int is_osc : 1;
+
+ int (*phy_init)(struct platform_device *pdev, int type);
+ int (*phy_exit)(struct platform_device *pdev, int type);
};
+
+extern void s3c_hsotg_set_platdata(struct s3c_hsotg_plat *pd);