omap: mux: Convert 2420 platform init code to use new mux code
Convert 2420 platform init code to use new mux code
Signed-off-by: Tony Lindgren <tony@atomide.com>
diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c
index bc67026..8cea623 100644
--- a/arch/arm/mach-omap2/board-apollon.c
+++ b/arch/arm/mach-omap2/board-apollon.c
@@ -35,7 +35,6 @@
#include <mach/gpio.h>
#include <plat/led.h>
-#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/common.h>
@@ -246,7 +245,7 @@
apollon_smc91x_resources[0].end = base + 0x30f;
udelay(100);
- omap_cfg_reg(W4__24XX_GPIO74);
+ omap_mux_init_gpio(74, 0);
if (gpio_request(APOLLON_ETHR_GPIO_IRQ, "SMC91x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
APOLLON_ETHR_GPIO_IRQ);
@@ -288,15 +287,15 @@
static void __init apollon_led_init(void)
{
/* LED0 - AA10 */
- omap_cfg_reg(AA10_242X_GPIO13);
+ omap_mux_init_signal("vlynq_clk.gpio_13", 0);
gpio_request(LED0_GPIO13, "LED0");
gpio_direction_output(LED0_GPIO13, 0);
/* LED1 - AA6 */
- omap_cfg_reg(AA6_242X_GPIO14);
+ omap_mux_init_signal("vlynq_rx1.gpio_14", 0);
gpio_request(LED1_GPIO14, "LED1");
gpio_direction_output(LED1_GPIO14, 0);
/* LED2 - AA4 */
- omap_cfg_reg(AA4_242X_GPIO15);
+ omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
gpio_request(LED2_GPIO15, "LED2");
gpio_direction_output(LED2_GPIO15, 0);
}
@@ -305,7 +304,7 @@
{
/* USB device */
/* DEVICE_SUSPEND */
- omap_cfg_reg(P21_242X_GPIO12);
+ omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
gpio_request(12, "USB suspend");
gpio_direction_output(12, 0);
omap2_usbfs_init(&apollon_usb_config);
@@ -330,7 +329,7 @@
apollon_usb_init();
/* REVISIT: where's the correct place */
- omap_cfg_reg(W19_24XX_SYS_NIRQ);
+ omap_mux_init_signal("sys_nirq", OMAP_PULL_ENA | OMAP_PULL_UP);
/* LCD PWR_EN */
omap_mux_init_signal("mcbsp2_dr.gpio_11", OMAP_PULL_ENA | OMAP_PULL_UP);
diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c
index cdcd4fb..2d9ff0f 100644
--- a/arch/arm/mach-omap2/board-h4.c
+++ b/arch/arm/mach-omap2/board-h4.c
@@ -33,7 +33,6 @@
#include <plat/control.h>
#include <mach/gpio.h>
-#include <plat/mux.h>
#include <plat/usb.h>
#include <plat/board.h>
#include <plat/common.h>
@@ -248,7 +247,7 @@
udelay(100);
- omap_cfg_reg(M15_24XX_GPIO92);
+ omap_mux_init_gpio(92, 0);
if (debug_card_init(cs_mem_base, H4_ETHR_GPIO_IRQ) < 0)
gpmc_cs_free(eth_cs);
@@ -358,8 +357,8 @@
* if not needed.
*/
#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
- omap_cfg_reg(K15_24XX_UART3_TX);
- omap_cfg_reg(K14_24XX_UART3_RX);
+ omap_mux_init_signal("uart3_tx_irtx.uart3_tx_irtx", 0);
+ omap_mux_init_signal("uart3_rx_irrx.uart3_rx_irrx", 0);
#endif
#if defined(CONFIG_KEYBOARD_OMAP) || defined(CONFIG_KEYBOARD_OMAP_MODULE)
diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c
index 03e6c9e..3ae9d0a 100644
--- a/arch/arm/mach-omap2/devices.c
+++ b/arch/arm/mach-omap2/devices.c
@@ -25,7 +25,6 @@
#include <plat/control.h>
#include <plat/tc.h>
#include <plat/board.h>
-#include <plat/mux.h>
#include <mach/gpio.h>
#include <plat/mmc.h>
#include <plat/dma.h>
@@ -672,19 +671,19 @@
OMAP_PIN_INPUT_PULLUP);
if (cpu_is_omap2420() && controller_nr == 0) {
- omap_cfg_reg(H18_24XX_MMC_CMD);
- omap_cfg_reg(H15_24XX_MMC_CLKI);
- omap_cfg_reg(G19_24XX_MMC_CLKO);
- omap_cfg_reg(F20_24XX_MMC_DAT0);
- omap_cfg_reg(F19_24XX_MMC_DAT_DIR0);
- omap_cfg_reg(G18_24XX_MMC_CMD_DIR);
+ omap_mux_init_signal("sdmmc_cmd", 0);
+ omap_mux_init_signal("sdmmc_clki", 0);
+ omap_mux_init_signal("sdmmc_clko", 0);
+ omap_mux_init_signal("sdmmc_dat0", 0);
+ omap_mux_init_signal("sdmmc_dat_dir0", 0);
+ omap_mux_init_signal("sdmmc_cmd_dir", 0);
if (mmc_controller->slots[0].wires == 4) {
- omap_cfg_reg(H14_24XX_MMC_DAT1);
- omap_cfg_reg(E19_24XX_MMC_DAT2);
- omap_cfg_reg(D19_24XX_MMC_DAT3);
- omap_cfg_reg(E20_24XX_MMC_DAT_DIR1);
- omap_cfg_reg(F18_24XX_MMC_DAT_DIR2);
- omap_cfg_reg(E18_24XX_MMC_DAT_DIR3);
+ omap_mux_init_signal("sdmmc_dat1", 0);
+ omap_mux_init_signal("sdmmc_dat2", 0);
+ omap_mux_init_signal("sdmmc_dat3", 0);
+ omap_mux_init_signal("sdmmc_dat_dir1", 0);
+ omap_mux_init_signal("sdmmc_dat_dir2", 0);
+ omap_mux_init_signal("sdmmc_dat_dir3", 0);
}
/*
diff --git a/arch/arm/mach-omap2/i2c.c b/arch/arm/mach-omap2/i2c.c
index 7951ae1..79c478c 100644
--- a/arch/arm/mach-omap2/i2c.c
+++ b/arch/arm/mach-omap2/i2c.c
@@ -21,32 +21,19 @@
#include <plat/cpu.h>
#include <plat/i2c.h>
-#include <plat/mux.h>
#include "mux.h"
void __init omap2_i2c_mux_pins(int bus_id)
{
- if (cpu_is_omap24xx()) {
- const int omap24xx_pins[][2] = {
- { M19_24XX_I2C1_SCL, L15_24XX_I2C1_SDA },
- { J15_24XX_I2C2_SCL, H19_24XX_I2C2_SDA },
- };
- int scl, sda;
-
- scl = omap24xx_pins[bus_id - 1][0];
- sda = omap24xx_pins[bus_id - 1][1];
- omap_cfg_reg(sda);
- omap_cfg_reg(scl);
- }
+ char mux_name[sizeof("i2c2_scl.i2c2_scl")];
/* First I2C bus is not muxable */
- if (cpu_is_omap34xx() && bus_id > 1) {
- char mux_name[sizeof("i2c2_scl.i2c2_scl")];
+ if (bus_id == 1)
+ return;
- sprintf(mux_name, "i2c%i_scl.i2c%i_scl", bus_id, bus_id);
- omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
- sprintf(mux_name, "i2c%i_sda.i2c%i_sda", bus_id, bus_id);
- omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
- }
+ sprintf(mux_name, "i2c%i_scl.i2c%i_scl", bus_id, bus_id);
+ omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
+ sprintf(mux_name, "i2c%i_sda.i2c%i_sda", bus_id, bus_id);
+ omap_mux_init_signal(mux_name, OMAP_PIN_INPUT);
}
diff --git a/arch/arm/mach-omap2/mcbsp.c b/arch/arm/mach-omap2/mcbsp.c
index c293370..87aa4c9 100644
--- a/arch/arm/mach-omap2/mcbsp.c
+++ b/arch/arm/mach-omap2/mcbsp.c
@@ -20,17 +20,18 @@
#include <mach/irqs.h>
#include <plat/dma.h>
-#include <plat/mux.h>
#include <plat/cpu.h>
#include <plat/mcbsp.h>
+#include "mux.h"
+
static void omap2_mcbsp2_mux_setup(void)
{
- omap_cfg_reg(Y15_24XX_MCBSP2_CLKX);
- omap_cfg_reg(R14_24XX_MCBSP2_FSX);
- omap_cfg_reg(W15_24XX_MCBSP2_DR);
- omap_cfg_reg(V15_24XX_MCBSP2_DX);
- omap_cfg_reg(V14_24XX_GPIO117);
+ omap_mux_init_signal("eac_ac_sclk.mcbsp2_clkx", OMAP_PULL_ENA);
+ omap_mux_init_signal("eac_ac_fs.mcbsp2_fsx", OMAP_PULL_ENA);
+ omap_mux_init_signal("eac_ac_din.mcbsp2_dr", OMAP_PULL_ENA);
+ omap_mux_init_signal("eac_ac_dout.mcbsp2_dx", OMAP_PULL_ENA);
+ omap_mux_init_gpio(117, OMAP_PULL_ENA);
/*
* TODO: Need to add MUX settings for OMAP 2430 SDP
*/
diff --git a/arch/arm/mach-omap2/usb-tusb6010.c b/arch/arm/mach-omap2/usb-tusb6010.c
index 10a2013..64a0112 100644
--- a/arch/arm/mach-omap2/usb-tusb6010.c
+++ b/arch/arm/mach-omap2/usb-tusb6010.c
@@ -17,8 +17,8 @@
#include <linux/usb/musb.h>
#include <plat/gpmc.h>
-#include <plat/mux.h>
+#include "mux.h"
static u8 async_cs, sync_cs;
static unsigned refclk_psec;
@@ -325,17 +325,17 @@
else {
/* assume OMAP 2420 ES2.0 and later */
if (dmachan & (1 << 0))
- omap_cfg_reg(AA10_242X_DMAREQ0);
+ omap_mux_init_signal("sys_ndmareq0", 0);
if (dmachan & (1 << 1))
- omap_cfg_reg(AA6_242X_DMAREQ1);
+ omap_mux_init_signal("sys_ndmareq1", 0);
if (dmachan & (1 << 2))
- omap_cfg_reg(E4_242X_DMAREQ2);
+ omap_mux_init_signal("sys_ndmareq2", 0);
if (dmachan & (1 << 3))
- omap_cfg_reg(G4_242X_DMAREQ3);
+ omap_mux_init_signal("sys_ndmareq3", 0);
if (dmachan & (1 << 4))
- omap_cfg_reg(D3_242X_DMAREQ4);
+ omap_mux_init_signal("sys_ndmareq4", 0);
if (dmachan & (1 << 5))
- omap_cfg_reg(E3_242X_DMAREQ5);
+ omap_mux_init_signal("sys_ndmareq5", 0);
}
/* so far so good ... register the device */