| config B43 |
| tristate "Broadcom 43xx wireless support (mac80211 stack)" |
| depends on SSB_POSSIBLE && MAC80211 && WLAN_80211 && HAS_DMA |
| select SSB |
| select FW_LOADER |
| select HW_RANDOM |
| ---help--- |
| b43 is a driver for the Broadcom 43xx series wireless devices. |
| |
| Check "lspci" for something like |
| "Broadcom Corporation BCM43XX 802.11 Wireless LAN Controller" |
| to determine whether you own such a device. |
| |
| This driver supports the new BCM43xx IEEE 802.11G devices, but not |
| the old IEEE 802.11B devices. Old devices are supported by |
| the b43legacy driver. |
| Note that this has nothing to do with the standard that your AccessPoint |
| supports (A, B, G or a combination). |
| IEEE 802.11G devices can talk to IEEE 802.11B AccessPoints. |
| |
| It is safe to include both b43 and b43legacy as the underlying glue |
| layer will automatically load the correct version for your device. |
| |
| This driver uses V4 firmware, which must be installed separately using |
| b43-fwcutter. |
| |
| This driver can be built as a module (recommended) that will be called "b43". |
| If unsure, say M. |
| |
| # Auto-select SSB PCI-HOST support, if possible |
| config B43_PCI_AUTOSELECT |
| bool |
| depends on B43 && SSB_PCIHOST_POSSIBLE |
| select SSB_PCIHOST |
| select SSB_B43_PCI_BRIDGE |
| default y |
| |
| # Auto-select SSB PCICORE driver, if possible |
| config B43_PCICORE_AUTOSELECT |
| bool |
| depends on B43 && SSB_DRIVER_PCICORE_POSSIBLE |
| select SSB_DRIVER_PCICORE |
| default y |
| |
| config B43_PCMCIA |
| bool "Broadcom 43xx PCMCIA device support (EXPERIMENTAL)" |
| depends on B43 && SSB_PCMCIAHOST_POSSIBLE && EXPERIMENTAL |
| select SSB_PCMCIAHOST |
| ---help--- |
| Broadcom 43xx PCMCIA device support. |
| |
| Support for 16bit PCMCIA devices. |
| Please note that most PC-CARD devices are _NOT_ 16bit PCMCIA |
| devices, but 32bit CardBUS devices. CardBUS devices are supported |
| out of the box by b43. |
| |
| With this config option you can drive b43 cards in |
| CompactFlash formfactor in a PCMCIA adaptor. |
| CF b43 cards can sometimes be found in handheld PCs. |
| |
| It's safe to select Y here, even if you don't have a B43 PCMCIA device. |
| |
| If unsure, say N. |
| |
| # Data transfers to the device via PIO |
| # This is only needed on PCMCIA devices. All others can do DMA properly. |
| config B43_PIO |
| bool |
| depends on B43 && (B43_PCMCIA || B43_FORCE_PIO) |
| select SSB_BLOCKIO |
| default y |
| |
| config B43_NPHY |
| bool "Pre IEEE 802.11n support (BROKEN)" |
| depends on B43 && EXPERIMENTAL && BROKEN |
| ---help--- |
| Support for the IEEE 802.11n draft. |
| |
| THIS IS BROKEN AND DOES NOT WORK YET. |
| |
| SAY N. |
| |
| config B43_PHY_LP |
| bool "IEEE 802.11g LP-PHY support (BROKEN)" |
| depends on B43 && EXPERIMENTAL && BROKEN |
| ---help--- |
| Support for the LP-PHY. |
| The LP-PHY is an IEEE 802.11g based PHY built into some notebooks |
| and embedded devices. |
| |
| THIS IS BROKEN AND DOES NOT WORK YET. |
| |
| SAY N. |
| |
| # This config option automatically enables b43 LEDS support, |
| # if it's possible. |
| config B43_LEDS |
| bool |
| depends on B43 && MAC80211_LEDS && (LEDS_CLASS = y || LEDS_CLASS = B43) |
| default y |
| |
| # This config option automatically enables b43 RFKILL support, |
| # if it's possible. |
| config B43_RFKILL |
| bool |
| depends on B43 && (RFKILL = y || RFKILL = B43) && RFKILL_INPUT && (INPUT_POLLDEV = y || INPUT_POLLDEV = B43) |
| default y |
| |
| config B43_DEBUG |
| bool "Broadcom 43xx debugging" |
| depends on B43 |
| ---help--- |
| Broadcom 43xx debugging messages. |
| |
| Say Y, if you want to find out why the driver does not |
| work for you. |
| |
| config B43_FORCE_PIO |
| bool "Force usage of PIO instead of DMA" |
| depends on B43 && B43_DEBUG |
| ---help--- |
| This will disable DMA and always enable PIO instead. |
| |
| Say N! |
| This is only for debugging the PIO engine code. You do |
| _NOT_ want to enable this. |