[PATCH] USB: remove usbcore-specific wakeup flags
This makes usbcore use the driver model wakeup flags for host controllers
and for their root hubs. Since previous patches have removed all users of
the HCD flags they replace, this converts the last users of those flags.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c
index 6368562..a98d978 100644
--- a/drivers/usb/core/hcd.c
+++ b/drivers/usb/core/hcd.c
@@ -367,21 +367,39 @@
/* DEVICE REQUESTS */
+ /* The root hub's remote wakeup enable bit is implemented using
+ * driver model wakeup flags. If this system supports wakeup
+ * through USB, userspace may change the default "allow wakeup"
+ * policy through sysfs or these calls.
+ *
+ * Most root hubs support wakeup from downstream devices, for
+ * runtime power management (disabling USB clocks and reducing
+ * VBUS power usage). However, not all of them do so; silicon,
+ * board, and BIOS bugs here are not uncommon, so these can't
+ * be treated quite like external hubs.
+ *
+ * Likewise, not all root hubs will pass wakeup events upstream,
+ * to wake up the whole system. So don't assume root hub and
+ * controller capabilities are identical.
+ */
+
case DeviceRequest | USB_REQ_GET_STATUS:
- tbuf [0] = (hcd->remote_wakeup << USB_DEVICE_REMOTE_WAKEUP)
+ tbuf [0] = (device_may_wakeup(&hcd->self.root_hub->dev)
+ << USB_DEVICE_REMOTE_WAKEUP)
| (1 << USB_DEVICE_SELF_POWERED);
tbuf [1] = 0;
len = 2;
break;
case DeviceOutRequest | USB_REQ_CLEAR_FEATURE:
if (wValue == USB_DEVICE_REMOTE_WAKEUP)
- hcd->remote_wakeup = 0;
+ device_set_wakeup_enable(&hcd->self.root_hub->dev, 0);
else
goto error;
break;
case DeviceOutRequest | USB_REQ_SET_FEATURE:
- if (hcd->can_wakeup && wValue == USB_DEVICE_REMOTE_WAKEUP)
- hcd->remote_wakeup = 1;
+ if (device_can_wakeup(&hcd->self.root_hub->dev)
+ && wValue == USB_DEVICE_REMOTE_WAKEUP)
+ device_set_wakeup_enable(&hcd->self.root_hub->dev, 1);
else
goto error;
break;
@@ -410,7 +428,7 @@
bufp = fs_rh_config_descriptor;
len = sizeof fs_rh_config_descriptor;
}
- if (hcd->can_wakeup)
+ if (device_can_wakeup(&hcd->self.root_hub->dev))
patch_wakeup = 1;
break;
case USB_DT_STRING << 8:
@@ -1804,16 +1822,10 @@
device_init_wakeup(&rhdev->dev,
device_can_wakeup(hcd->self.controller));
- // ... all these hcd->*_wakeup flags will vanish
- hcd->can_wakeup = device_can_wakeup(hcd->self.controller);
-
- /* hcd->driver->reset() reported can_wakeup, probably with
- * assistance from board's boot firmware.
- * NOTE: normal devices won't enable wakeup by default.
- */
- if (hcd->can_wakeup)
+ /* NOTE: root hub and controller capabilities may not be the same */
+ if (device_can_wakeup(hcd->self.controller)
+ && device_can_wakeup(&hcd->self.root_hub->dev))
dev_dbg(hcd->self.controller, "supports USB remote wakeup\n");
- hcd->remote_wakeup = hcd->can_wakeup;
/* enable irqs just before we start the controller */
if (hcd->driver->irq) {