S2IO: Fixes for MSI and MSIX
- Added debug statements to print a debug message if the MSI/MSI-X vector (or)
data is zero.
- This patch removes the code that will enable NAPI for the case of single
ring and MSI-X / MSI case. There are some issue in the enabling NAPI with
MSI/MSI-X. So we are turning off NAPI in the case of MSI/MSI-X.
Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c
index fd85648..7cc07c8 100644
--- a/drivers/net/s2io.c
+++ b/drivers/net/s2io.c
@@ -6112,7 +6112,7 @@
}
}
if (sp->intr_type == MSI_X) {
- int i;
+ int i, msix_tx_cnt=0,msix_rx_cnt=0;
for (i=1; (sp->s2io_entries[i].in_use == MSIX_FLG); i++) {
if (sp->s2io_entries[i].type == MSIX_FIFO_TYPE) {
@@ -6121,16 +6121,36 @@
err = request_irq(sp->entries[i].vector,
s2io_msix_fifo_handle, 0, sp->desc[i],
sp->s2io_entries[i].arg);
- DBG_PRINT(ERR_DBG, "%s @ 0x%llx\n", sp->desc[i],
- (unsigned long long)sp->msix_info[i].addr);
+ /* If either data or addr is zero print it */
+ if(!(sp->msix_info[i].addr &&
+ sp->msix_info[i].data)) {
+ DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx"
+ "Data:0x%lx\n",sp->desc[i],
+ (unsigned long long)
+ sp->msix_info[i].addr,
+ (unsigned long)
+ ntohl(sp->msix_info[i].data));
+ } else {
+ msix_tx_cnt++;
+ }
} else {
sprintf(sp->desc[i], "%s:MSI-X-%d-RX",
dev->name, i);
err = request_irq(sp->entries[i].vector,
s2io_msix_ring_handle, 0, sp->desc[i],
sp->s2io_entries[i].arg);
- DBG_PRINT(ERR_DBG, "%s @ 0x%llx\n", sp->desc[i],
- (unsigned long long)sp->msix_info[i].addr);
+ /* If either data or addr is zero print it */
+ if(!(sp->msix_info[i].addr &&
+ sp->msix_info[i].data)) {
+ DBG_PRINT(ERR_DBG, "%s @ Addr:0x%llx"
+ "Data:0x%lx\n",sp->desc[i],
+ (unsigned long long)
+ sp->msix_info[i].addr,
+ (unsigned long)
+ ntohl(sp->msix_info[i].data));
+ } else {
+ msix_rx_cnt++;
+ }
}
if (err) {
DBG_PRINT(ERR_DBG,"%s:MSI-X-%d registration "
@@ -6140,6 +6160,8 @@
}
sp->s2io_entries[i].in_use = MSIX_REGISTERED_SUCCESS;
}
+ printk("MSI-X-TX %d entries enabled\n",msix_tx_cnt);
+ printk("MSI-X-RX %d entries enabled\n",msix_rx_cnt);
}
if (sp->intr_type == INTA) {
err = request_irq((int) sp->pdev->irq, s2io_isr, IRQF_SHARED,
@@ -6704,8 +6726,7 @@
"Defaulting to INTA\n");
*dev_intr_type = INTA;
}
- if ( (rx_ring_num > 1) && (*dev_intr_type != INTA) )
- napi = 0;
+
if (rx_ring_mode > 3) {
DBG_PRINT(ERR_DBG, "s2io: Requested ring mode not supported\n");
DBG_PRINT(ERR_DBG, "s2io: Defaulting to 3-buffer mode\n");