Merge tag 'for_3.13_late/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.13/dt
Add i2c aliases
Add McASP and audio support
Add reset/idle on init bindings for OMAP
Add more nodes for AM4272
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 91b7049..808c154 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -21,7 +21,8 @@
Optional properties:
- ti,no_idle_on_suspend: When present, it prevents the PM to idle the module
during suspend.
-
+- ti,no-reset-on-init: When present, the module should not be reset at init
+- ti,no-idle-on-init: When present, the module should not be idled at init
Example:
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index eabacf9..9874294 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -119,6 +119,19 @@
};
};
};
+
+ sound {
+ compatible = "ti,da830-evm-audio";
+ ti,model = "AM335x-EVM";
+ ti,audio-codec = <&tlv320aic3106>;
+ ti,mcasp-controller = <&mcasp1>;
+ ti,codec-clock-rate = <12000000>;
+ ti,audio-routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT",
+ "LINE1L", "Line In",
+ "LINE1R", "Line In";
+ };
};
&am33xx_pinmux {
@@ -279,6 +292,15 @@
0xec 0x00 /* lcd_ac_bias_en.lcd_ac_bias_en, OUTPUT | MODE0 */
>;
};
+
+ am335x_evm_audio_pins: am335x_evm_audio_pins {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rx_dv.mcasp1_aclkx */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_txd3.mcasp1_fsx */
+ 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
};
&uart0 {
@@ -373,6 +395,18 @@
compatible = "ti,tmp275";
reg = <0x48>;
};
+
+ tlv320aic3106: tlv320aic3106@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ status = "okay";
+
+ /* Regulators */
+ AVDD-supply = <&vaux2_reg>;
+ IOVDD-supply = <&vaux2_reg>;
+ DRVDD-supply = <&vaux2_reg>;
+ DVDD-supply = <&vbat>;
+ };
};
&lcdc {
@@ -476,6 +510,22 @@
#include "tps65910.dtsi"
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&am335x_evm_audio_pins>;
+
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 2
+ >;
+ tx-num-evt = <1>;
+ rx-num-evt = <1>;
+};
+
&tps {
vcc1-supply = <&vbat>;
vcc2-supply = <&vbat>;
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index 5f12b28..03febf8 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -115,6 +115,17 @@
brightness-levels = <0 58 61 66 75 90 125 170 255>;
default-brightness-level = <8>;
};
+
+ sound {
+ compatible = "ti,da830-evm-audio";
+ ti,model = "AM335x-EVMSK";
+ ti,audio-codec = <&tlv320aic3106>;
+ ti,mcasp-controller = <&mcasp1>;
+ ti,codec-clock-rate = <24576000>;
+ ti,audio-routing =
+ "Headphone Jack", "HPLOUT",
+ "Headphone Jack", "HPROUT";
+ };
};
&am33xx_pinmux {
@@ -244,6 +255,15 @@
0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
>;
};
+
+ mcasp1_pins: mcasp1_pins {
+ pinctrl-single,pins = <
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_crs.mcasp1_aclkx */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* mii1_rxerr.mcasp1_fsx */
+ 0x108 (PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* mii1_col.mcasp1_axr2 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
+ >;
+ };
};
&uart0 {
@@ -291,6 +311,18 @@
st,max-limit-y = <550>;
st,max-limit-z = <750>;
};
+
+ tlv320aic3106: tlv320aic3106@1b {
+ compatible = "ti,tlv320aic3106";
+ reg = <0x1b>;
+ status = "okay";
+
+ /* Regulators */
+ AVDD-supply = <&vaux2_reg>;
+ IOVDD-supply = <&vaux2_reg>;
+ DRVDD-supply = <&vaux2_reg>;
+ DVDD-supply = <&vbat>;
+ };
};
&usb {
@@ -433,3 +465,23 @@
&aes {
status = "okay";
};
+
+&gpio0 {
+ ti,no-reset-on-init;
+};
+
+&mcasp1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp1_pins>;
+
+ status = "okay";
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ /* 4 serializers */
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 0 0 1 2
+ >;
+ tx-num-evt = <1>;
+ rx-num-evt = <1>;
+};
diff --git a/arch/arm/boot/dts/am335x-igep0033.dtsi b/arch/arm/boot/dts/am335x-igep0033.dtsi
index 06eba07..6196244 100644
--- a/arch/arm/boot/dts/am335x-igep0033.dtsi
+++ b/arch/arm/boot/dts/am335x-igep0033.dtsi
@@ -44,6 +44,13 @@
regulator-max-microvolt = <5000000>;
regulator-boot-on;
};
+
+ vmmc: fixedregulator@0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
};
&am33xx_pinmux {
@@ -180,6 +187,12 @@
};
};
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmc>;
+ bus-width = <4>;
+};
+
&uart0 {
status = "okay";
pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index 7db3c81..97f5019 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -18,6 +18,9 @@
interrupt-parent = <&intc>;
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &uart2;
@@ -674,6 +677,7 @@
reg = <0x44d00000 0x4000 /* M3 UMEM */
0x44d80000 0x2000>; /* M3 DMEM */
ti,hwmods = "wkup_m3";
+ ti,no-reset-on-init;
};
elm: elm@48080000 {
@@ -713,6 +717,7 @@
gpmc: gpmc@50000000 {
compatible = "ti,am3352-gpmc";
ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
reg = <0x50000000 0x2000>;
interrupts = <100>;
gpmc,num-cs = <7>;
@@ -740,5 +745,33 @@
<&edma 5>;
dma-names = "tx", "rx";
};
+
+ mcasp0: mcasp@48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 8>,
+ <&edma 9>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp1: mcasp@4803C000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp1";
+ reg = <0x4803C000 0x2000>,
+ <0x46400000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <82>, <83>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 10>,
+ <&edma 11>;
+ dma-names = "tx", "rx";
+ };
};
};
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index a403172..974d103 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -18,7 +18,12 @@
aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
serial0 = &uart0;
+ ethernet0 = &cpsw_emac0;
+ ethernet1 = &cpsw_emac1;
};
cpus {
@@ -39,11 +44,42 @@
<0x48240100 0x0100>;
};
+ l2-cache-controller@48242000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x48242000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ am43xx_pinmux: pinmux@44e10800 {
+ compatible = "pinctrl-single";
+ reg = <0x44e10800 0x31c>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0xffffffff>;
+ };
+
ocp {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+ ti,hwmods = "l3_main";
+
+ edma: edma@49000000 {
+ compatible = "ti,edma3";
+ ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2";
+ reg = <0x49000000 0x10000>,
+ <0x44e10f90 0x10>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ #dma-cells = <1>;
+ dma-channels = <64>;
+ ti,edma-regions = <4>;
+ ti,edma-slots = <256>;
+ };
uart0: serial@44e09000 {
compatible = "ti,am4372-uart","ti,omap2-uart";
@@ -92,6 +128,18 @@
status = "disabled";
};
+ mailbox: mailbox@480C8000 {
+ compatible = "ti,omap4-mailbox";
+ reg = <0x480C8000 0x200>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ ti,hwmods = "mailbox";
+ ti,mbox-num-users = <4>;
+ ti,mbox-num-fifos = <8>;
+ ti,mbox-names = "wkup_m3";
+ ti,mbox-data = <0 0 0 0>;
+ status = "disabled";
+ };
+
timer1: timer@44e31000 {
compatible = "ti,am4372-timer-1ms","ti,am335x-timer-1ms";
reg = <0x44e31000 0x400>;
@@ -203,7 +251,6 @@
reg = <0x44e35000 0x1000>;
interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "wd_timer2";
- status = "disabled";
};
gpio0: gpio@44e07000 {
@@ -318,6 +365,40 @@
status = "disabled";
};
+ mmc1: mmc@48060000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x48060000 0x1000>;
+ ti,hwmods = "mmc1";
+ ti,dual-volt;
+ ti,needs-special-reset;
+ dmas = <&edma 24
+ &edma 25>;
+ dma-names = "tx", "rx";
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ mmc2: mmc@481d8000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x481d8000 0x1000>;
+ ti,hwmods = "mmc2";
+ ti,needs-special-reset;
+ dmas = <&edma 2
+ &edma 3>;
+ dma-names = "tx", "rx";
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ mmc3: mmc@47810000 {
+ compatible = "ti,omap4-hsmmc";
+ reg = <0x47810000 0x1000>;
+ ti,hwmods = "mmc3";
+ ti,needs-special-reset;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
spi1: spi@481a0000 {
compatible = "ti,am4372-mcspi","ti,omap4-mcspi";
reg = <0x481a0000 0x400>;
@@ -366,50 +447,173 @@
GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH
GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ #address-cells = <1>;
+ #size-cells = <1>;
ti,hwmods = "cpgmac0";
status = "disabled";
+ cpdma_channels = <8>;
+ ale_entries = <1024>;
+ bd_ram_size = <0x2000>;
+ no_bd_ram = <0>;
+ rx_descs = <64>;
+ mac_control = <0x20>;
+ slaves = <2>;
+ active_slave = <0>;
+ cpts_clock_mult = <0x80000000>;
+ cpts_clock_shift = <29>;
+ ranges;
+
+ davinci_mdio: mdio@4a101000 {
+ compatible = "ti,am4372-mdio","ti,davinci_mdio";
+ reg = <0x4a101000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ti,hwmods = "davinci_mdio";
+ bus_freq = <1000000>;
+ status = "disabled";
+ };
+
+ cpsw_emac0: slave@4a100200 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
+
+ cpsw_emac1: slave@4a100300 {
+ /* Filled in by U-Boot */
+ mac-address = [ 00 00 00 00 00 00 ];
+ };
};
epwmss0: epwmss@48300000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48300000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss0";
status = "disabled";
+
+ ecap0: ecap@48300100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48300100 0x80>;
+ ti,hwmods = "ecap0";
+ status = "disabled";
+ };
+
+ ehrpwm0: ehrpwm@48300200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48300200 0x80>;
+ ti,hwmods = "ehrpwm0";
+ status = "disabled";
+ };
};
epwmss1: epwmss@48302000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48302000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss1";
status = "disabled";
+
+ ecap1: ecap@48302100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48302100 0x80>;
+ ti,hwmods = "ecap1";
+ status = "disabled";
+ };
+
+ ehrpwm1: ehrpwm@48302200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48302200 0x80>;
+ ti,hwmods = "ehrpwm1";
+ status = "disabled";
+ };
};
epwmss2: epwmss@48304000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48304000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss2";
status = "disabled";
+
+ ecap2: ecap@48304100 {
+ compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+ reg = <0x48304100 0x80>;
+ ti,hwmods = "ecap2";
+ status = "disabled";
+ };
+
+ ehrpwm2: ehrpwm@48304200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48304200 0x80>;
+ ti,hwmods = "ehrpwm2";
+ status = "disabled";
+ };
};
epwmss3: epwmss@48306000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48306000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss3";
status = "disabled";
+
+ ehrpwm3: ehrpwm@48306200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48306200 0x80>;
+ ti,hwmods = "ehrpwm3";
+ status = "disabled";
+ };
};
epwmss4: epwmss@48308000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x48308000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss4";
status = "disabled";
+
+ ehrpwm4: ehrpwm@48308200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x48308200 0x80>;
+ ti,hwmods = "ehrpwm4";
+ status = "disabled";
+ };
};
epwmss5: epwmss@4830a000 {
compatible = "ti,am4372-pwmss","ti,am33xx-pwmss";
reg = <0x4830a000 0x10>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
ti,hwmods = "epwmss5";
status = "disabled";
+
+ ehrpwm5: ehrpwm@4830a200 {
+ compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+ reg = <0x4830a200 0x80>;
+ ti,hwmods = "ehrpwm5";
+ status = "disabled";
+ };
+ };
+
+ sham: sham@53100000 {
+ compatible = "ti,omap5-sham";
+ ti,hwmods = "sham";
+ reg = <0x53100000 0x300>;
+ dmas = <&edma 36>;
+ dma-names = "rx";
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
};
aes: aes@53501000 {
@@ -417,6 +621,9 @@
ti,hwmods = "aes";
reg = <0x53501000 0xa0>;
interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma 6
+ &edma 5>;
+ dma-names = "tx", "rx";
};
des: des@53701000 {
@@ -424,6 +631,37 @@
ti,hwmods = "des";
reg = <0x53701000 0xa0>;
interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&edma 34
+ &edma 33>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp0: mcasp@48038000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp0";
+ reg = <0x48038000 0x2000>,
+ <0x46000000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <80>, <81>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 8>,
+ <&edma 9>;
+ dma-names = "tx", "rx";
+ };
+
+ mcasp1: mcasp@4803C000 {
+ compatible = "ti,am33xx-mcasp-audio";
+ ti,hwmods = "mcasp1";
+ reg = <0x4803C000 0x2000>,
+ <0x46400000 0x400000>;
+ reg-names = "mpu", "dat";
+ interrupts = <82>, <83>;
+ interrupts-names = "tx", "rx";
+ status = "disabled";
+ dmas = <&edma 10>,
+ <&edma 11>;
+ dma-names = "tx", "rx";
};
};
};
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 74174d4..fbf9c4c 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -11,8 +11,176 @@
/dts-v1/;
#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "TI AM43x EPOS EVM";
compatible = "ti,am43x-epos-evm","ti,am4372","ti,am43";
+
+ vmmcsd_fixed: fixedregulator-sd {
+ compatible = "regulator-fixed";
+ regulator-name = "vmmcsd_fixed";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ };
+
+ am43xx_pinmux: pinmux@44e10800 {
+ cpsw_default: cpsw_default {
+ pinctrl-single,pins = <
+ /* Slave 1 */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs */
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */
+ 0x114 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txen.rmii1_txen */
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxdv.rmii1_rxdv */
+ 0x124 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */
+ 0x128 (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */
+ >;
+ };
+
+ cpsw_sleep: cpsw_sleep {
+ pinctrl-single,pins = <
+ /* Slave 1 reset value */
+ 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x114 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x118 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x124 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x128 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ davinci_mdio_default: davinci_mdio_default {
+ pinctrl-single,pins = <
+ /* MDIO */
+ 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */
+ 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
+ >;
+ };
+
+ davinci_mdio_sleep: davinci_mdio_sleep {
+ pinctrl-single,pins = <
+ /* MDIO reset value */
+ 0x148 (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ 0x14c (PIN_INPUT_PULLDOWN | MUX_MODE7)
+ >;
+ };
+
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,pins = <
+ 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+ 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+ >;
+ };
+ };
+
+ matrix_keypad: matrix_keypad@0 {
+ compatible = "gpio-matrix-keypad";
+ debounce-delay-ms = <5>;
+ col-scan-delay-us = <2>;
+
+ row-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH /* Bank0, pin12 */
+ &gpio0 13 GPIO_ACTIVE_HIGH /* Bank0, pin13 */
+ &gpio0 14 GPIO_ACTIVE_HIGH /* Bank0, pin14 */
+ &gpio0 15 GPIO_ACTIVE_HIGH>; /* Bank0, pin15 */
+
+ col-gpios = <&gpio3 9 GPIO_ACTIVE_HIGH /* Bank3, pin9 */
+ &gpio3 10 GPIO_ACTIVE_HIGH /* Bank3, pin10 */
+ &gpio2 18 GPIO_ACTIVE_HIGH /* Bank2, pin18 */
+ &gpio2 19 GPIO_ACTIVE_HIGH>; /* Bank2, pin19 */
+
+ linux,keymap = <0x00000201 /* P1 */
+ 0x01000204 /* P4 */
+ 0x02000207 /* P7 */
+ 0x0300020a /* NUMERIC_STAR */
+ 0x00010202 /* P2 */
+ 0x01010205 /* P5 */
+ 0x02010208 /* P8 */
+ 0x03010200 /* P0 */
+ 0x00020203 /* P3 */
+ 0x01020206 /* P6 */
+ 0x02020209 /* P9 */
+ 0x0302020b /* NUMERIC_POUND */
+ 0x00030067 /* UP */
+ 0x0103006a /* RIGHT */
+ 0x0203006c /* DOWN */
+ 0x03030069>; /* LEFT */
+ };
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&vmmcsd_fixed>;
+ bus-width = <4>;
+};
+
+&mac {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&cpsw_default>;
+ pinctrl-1 = <&cpsw_sleep>;
+ status = "okay";
+};
+
+&davinci_mdio {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&davinci_mdio_default>;
+ pinctrl-1 = <&davinci_mdio_sleep>;
+ status = "okay";
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <16>;
+ phy-mode = "rmii";
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <1>;
+ phy-mode = "rmii";
+};
+
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ at24@50 {
+ compatible = "at24,24c256";
+ pagesize = <64>;
+ reg = <0x50>;
+ };
+
+ pixcir_ts@5c {
+ compatible = "pixcir,pixcir_ts";
+ reg = <0x5c>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <17 0>;
+
+ attb-gpio = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+
+ x-size = <1024>;
+ y-size = <768>;
+ };
+};
+
+&gpio0 {
+ status = "okay";
+};
+
+&gpio1 {
+ status = "okay";
+};
+
+&gpio2 {
+ status = "okay";
+};
+
+&gpio3 {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index c01ef76..98ff655 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -20,6 +20,11 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ i2c4 = &i2c5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index 7669c16..fa532aa 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -173,6 +173,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};
diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts
index a84684a..b9b55c9 100644
--- a/arch/arm/boot/dts/omap3-gta04.dts
+++ b/arch/arm/boot/dts/omap3-gta04.dts
@@ -131,6 +131,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index d64fa04..e13b697 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -87,6 +87,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
+ phys = <&usb2_phy>;
+ phy-names = "usb2-phy";
mode = <2>;
power = <50>;
};
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 16420ae..493b6d4 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -19,6 +19,9 @@
interrupt-parent = <&intc>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
index 56c4354..816d1c9 100644
--- a/arch/arm/boot/dts/omap4-panda-es.dts
+++ b/arch/arm/boot/dts/omap4-panda-es.dts
@@ -62,3 +62,7 @@
gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
};
};
+
+&gpio1 {
+ ti,no-reset-on-init;
+};
diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi
index 6be1f56..0d8fdba 100644
--- a/arch/arm/boot/dts/omap4.dtsi
+++ b/arch/arm/boot/dts/omap4.dtsi
@@ -17,6 +17,10 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -214,6 +218,7 @@
gpmc,num-cs = <8>;
gpmc,num-waitpins = <4>;
ti,hwmods = "gpmc";
+ ti,no-idle-on-init;
};
uart1: serial@4806a000 {
@@ -492,6 +497,7 @@
reg = <0x4c000000 0x100>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "emif1";
+ ti,no-idle-on-init;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
@@ -503,6 +509,7 @@
reg = <0x4d000000 0x100>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "emif2";
+ ti,no-idle-on-init;
phy-type = <1>;
hw-caps-read-idle-ctrl;
hw-caps-ll-interface;
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index d784b3a..e06a04a 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -334,8 +334,6 @@
regulator-name = "smps10_out1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- regulator-always-on;
- regulator-boot-on;
};
ldo1_reg: ldo1 {
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index 6192c45..2cb72ba 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -21,6 +21,11 @@
interrupt-parent = <&gic>;
aliases {
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ i2c4 = &i2c5;
serial0 = &uart1;
serial1 = &uart2;
serial2 = &uart3;
@@ -52,7 +57,6 @@
<GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>;
- clock-frequency = <6144000>;
};
gic: interrupt-controller@48211000 {
@@ -607,6 +611,7 @@
emif1: emif@4c000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif1";
+ ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4c000000 0x400>;
interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -618,6 +623,7 @@
emif2: emif@4d000000 {
compatible = "ti,emif-4d5";
ti,hwmods = "emif2";
+ ti,no-idle-on-init;
phy-type = <2>; /* DDR PHY type: Intelli PHY */
reg = <0x4d000000 0x400>;
interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
@@ -648,6 +654,7 @@
reg = <0x4a030000 0x10000>;
interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
usb-phy = <&usb2_phy>, <&usb3_phy>;
+ dr_mode = "peripheral";
tx-fifo-resize;
};
};
diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h
new file mode 100644
index 0000000..eb6c366a
--- /dev/null
+++ b/include/dt-bindings/pinctrl/am43xx.h
@@ -0,0 +1,31 @@
+/*
+ * This header provides constants specific to AM43XX pinctrl bindings.
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_AM43XX_H
+#define _DT_BINDINGS_PINCTRL_AM43XX_H
+
+#define MUX_MODE0 0
+#define MUX_MODE1 1
+#define MUX_MODE2 2
+#define MUX_MODE3 3
+#define MUX_MODE4 4
+#define MUX_MODE5 5
+#define MUX_MODE6 6
+#define MUX_MODE7 7
+
+#define PULL_DISABLE (1 << 16)
+#define PULL_UP (1 << 17)
+#define INPUT_EN (1 << 18)
+#define SLEWCTRL_FAST (1 << 19)
+#define DS0_PULL_UP_DOWN_EN (1 << 27)
+
+#define PIN_OUTPUT (PULL_DISABLE)
+#define PIN_OUTPUT_PULLUP (PULL_UP)
+#define PIN_OUTPUT_PULLDOWN 0
+#define PIN_INPUT (INPUT_EN | PULL_DISABLE)
+#define PIN_INPUT_PULLUP (INPUT_EN | PULL_UP)
+#define PIN_INPUT_PULLDOWN (INPUT_EN)
+
+#endif
+