diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 59397c2..629eee2 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -291,6 +291,7 @@
 	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-d2-network.dtb \
 	orion5x-lacie-ethernet-disk-mini-v2.dtb \
+	orion5x-maxtor-shared-storage-2.dtb \
 	orion5x-rd88f5182-nas.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
 dtb-$(CONFIG_ARCH_QCOM) += qcom-msm8660-surf.dtb \
diff --git a/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts b/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
new file mode 100644
index 0000000..ff34849
--- /dev/null
+++ b/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "orion5x-mv88f5182.dtsi"
+
+/ {
+	model = "Maxtor Shared Storage II";
+	compatible = "maxtor,shared-storage-2", "marvell,orion5x-88f5182", "marvell,orion5x";
+
+	memory {
+		reg = <0x00000000 0x4000000>; /* 64 MB */
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8 earlyprintk";
+		linux,stdout-path = &uart0;
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+			 <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+			 <MBUS_ID(0x01, 0x0f) 0 0xff800000 0x40000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power {
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+		};
+
+		reset {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	devbus,keep-config;
+
+	/*
+	 * Currently the MTD code does not recognize the MX29LV400CBCT
+	 * as a bottom-type device. This could cause risks of
+	 * accidentally erasing critical flash sectors. We thus define
+	 * a single, write-protected partition covering the whole
+	 * flash.  TODO: once the flash part TOP/BOTTOM detection
+	 * issue is sorted out in the MTD code, break this into at
+	 * least three partitions: 'u-boot code', 'u-boot environment'
+	 * and 'whatever is left'.
+	 */
+	flash@0 {
+		compatible = "cfi-flash";
+		reg = <0 0x40000>;
+		bank-width = <1>;
+                #address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy: ethernet-phy {
+		reg = <8>;
+	};
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	ethernet-port@0 {
+		phy-handle = <&ethphy>;
+	};
+};
+
+&i2c {
+	status = "okay";
+	clock-frequency = <100000>;
+	#address-cells = <1>;
+
+	rtc@68 {
+		compatible = "st,m41t81";
+		reg = <0x68>;
+		pinctrl-0 = <&pmx_rtc>;
+		pinctrl-names = "default";
+		interrupt-parent = <&gpio0>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pinctrl {
+	pinctrl-0 = <&pmx_leds &pmx_misc>;
+	pinctrl-names = "default";
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp11", "mpp12";
+		marvell,function = "gpio";
+	};
+
+	/*
+	 * MPP0: Power LED
+	 * MPP1: Error LED
+	 */
+	pmx_leds: pmx-leds {
+		marvell,pins = "mpp0", "mpp1";
+		marvell,function = "gpio";
+	};
+
+	/*
+	 * MPP4: HDD ind. (Single/Dual)
+	 * MPP5: HD0 5V control
+	 * MPP6: HD0 12V control
+	 * MPP7: HD1 5V control
+	 * MPP8: HD1 12V control
+	 */
+	pmx_misc: pmx-misc {
+		marvell,pins = "mpp4", "mpp5", "mpp6", "mpp7", "mpp8", "mpp10";
+		marvell,function = "gpio";
+	};
+
+	pmx_rtc: pmx-rtc {
+		marvell,pins = "mpp3";
+		marvell,function = "gpio";
+	};
+
+	pmx_sata0_led_active: pmx-sata0-led-active {
+		marvell,pins = "mpp14";
+		marvell,function = "sata0";
+	};
+
+	pmx_sata1_led_active: pmx-sata1-led-active {
+		marvell,pins = "mpp15";
+		marvell,function = "sata1";
+	};
+
+	/*
+	 * Non MPP GPIOs:
+	 *  GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok)
+	 *  GPIO 23: Blue front LED off
+	 *  GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled)
+	 */
+};
+
+&sata {
+	pinctrl-0 = <&pmx_sata0_led_active
+		     &pmx_sata1_led_active>;
+	pinctrl-names = "default";
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/mach-orion5x/Kconfig b/arch/arm/mach-orion5x/Kconfig
index 3c4ad83..2412efb 100644
--- a/arch/arm/mach-orion5x/Kconfig
+++ b/arch/arm/mach-orion5x/Kconfig
@@ -129,8 +129,9 @@
 	  Say 'Y' here if you want your kernel to support the
 	  LaCie 2Big Network NAS.
 
-config MACH_MSS2
-	bool "Maxtor Shared Storage II"
+config MACH_MSS2_DT
+	bool "Maxtor Shared Storage II (Flattened Device Tree)"
+	select ARCH_ORION5X_DT
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Maxtor Shared Storage II platform.
diff --git a/arch/arm/mach-orion5x/Makefile b/arch/arm/mach-orion5x/Makefile
index 787dcee..a40b5c9 100644
--- a/arch/arm/mach-orion5x/Makefile
+++ b/arch/arm/mach-orion5x/Makefile
@@ -13,7 +13,6 @@
 obj-$(CONFIG_MACH_TS78XX)	+= ts78xx-setup.o
 obj-$(CONFIG_MACH_MV2120)	+= mv2120-setup.o
 obj-$(CONFIG_MACH_NET2BIG)	+= net2big-setup.o
-obj-$(CONFIG_MACH_MSS2)		+= mss2-setup.o
 obj-$(CONFIG_MACH_WNR854T)	+= wnr854t-setup.o
 obj-$(CONFIG_MACH_RD88F5181L_GE)	+= rd88f5181l-ge-setup.o
 obj-$(CONFIG_MACH_RD88F5181L_FXO)	+= rd88f5181l-fxo-setup.o
@@ -22,4 +21,5 @@
 
 obj-$(CONFIG_ARCH_ORION5X_DT)		+= board-dt.o
 obj-$(CONFIG_MACH_D2NET_DT)	+= board-d2net.o
+obj-$(CONFIG_MACH_MSS2_DT)	+= board-mss2.o
 obj-$(CONFIG_MACH_RD88F5182_DT)	+= board-rd88f5182.o
diff --git a/arch/arm/mach-orion5x/board-dt.c b/arch/arm/mach-orion5x/board-dt.c
index 78d2e52..35d418f 100644
--- a/arch/arm/mach-orion5x/board-dt.c
+++ b/arch/arm/mach-orion5x/board-dt.c
@@ -61,6 +61,9 @@
 		cpu_idle_poll_ctrl(true);
 	}
 
+	if (of_machine_is_compatible("maxtor,shared-storage-2"))
+		mss2_init();
+
 	of_platform_populate(NULL, of_default_bus_match_table,
 			     orion5x_auxdata_lookup, NULL);
 }
diff --git a/arch/arm/mach-orion5x/board-mss2.c b/arch/arm/mach-orion5x/board-mss2.c
new file mode 100644
index 0000000..66f9c3b
--- /dev/null
+++ b/arch/arm/mach-orion5x/board-mss2.c
@@ -0,0 +1,90 @@
+/*
+ * Maxtor Shared Storage II Board Setup
+ *
+ * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include <mach/bridge-regs.h>
+#include "common.h"
+
+/*****************************************************************************
+ * Maxtor Shared Storage II Info
+ ****************************************************************************/
+
+/****************************************************************************
+ * PCI setup
+ ****************************************************************************/
+static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	int irq;
+
+	/*
+	 * Check for devices with hard-wired IRQs.
+	 */
+	irq = orion5x_pci_map_irq(dev, slot, pin);
+	if (irq != -1)
+		return irq;
+
+	return -1;
+}
+
+static struct hw_pci mss2_pci __initdata = {
+	.nr_controllers = 2,
+	.setup		= orion5x_pci_sys_setup,
+	.scan		= orion5x_pci_sys_scan_bus,
+	.map_irq	= mss2_pci_map_irq,
+};
+
+static int __init mss2_pci_init(void)
+{
+	if (machine_is_mss2())
+		pci_common_init(&mss2_pci);
+
+	return 0;
+}
+subsys_initcall(mss2_pci_init);
+
+/*****************************************************************************
+ * MSS2 power off method
+ ****************************************************************************/
+/*
+ * On the Maxtor Shared Storage II, the shutdown process is the following :
+ * - Userland modifies U-boot env to tell U-boot to go idle at next boot
+ * - The board reboots
+ * - U-boot starts and go into an idle mode until the user press "power"
+ */
+static void mss2_power_off(void)
+{
+	u32 reg;
+
+	/*
+	 * Enable and issue soft reset
+	 */
+	reg = readl(RSTOUTn_MASK);
+	reg |= 1 << 2;
+	writel(reg, RSTOUTn_MASK);
+
+	reg = readl(CPU_SOFT_RESET);
+	reg |= 1;
+	writel(reg, CPU_SOFT_RESET);
+}
+
+void __init mss2_init(void)
+{
+	/* register mss2 specific power-off method */
+	pm_power_off = mss2_power_off;
+}
diff --git a/arch/arm/mach-orion5x/common.h b/arch/arm/mach-orion5x/common.h
index 7d64a17..db7e056 100644
--- a/arch/arm/mach-orion5x/common.h
+++ b/arch/arm/mach-orion5x/common.h
@@ -68,6 +68,12 @@
 struct tag;
 extern void __init tag_fixup_mem32(struct tag *, char **, struct meminfo *);
 
+#ifdef CONFIG_MACH_MSS2_DT
+extern void mss2_init(void);
+#else
+static inline void mss2_init(void) {}
+#endif
+
 /*****************************************************************************
  * Helpers to access Orion registers
  ****************************************************************************/
diff --git a/arch/arm/mach-orion5x/mss2-setup.c b/arch/arm/mach-orion5x/mss2-setup.c
deleted file mode 100644
index e105130..0000000
--- a/arch/arm/mach-orion5x/mss2-setup.c
+++ /dev/null
@@ -1,274 +0,0 @@
-/*
- * Maxtor Shared Storage II Board Setup
- *
- * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include <mach/bridge-regs.h>
-#include "common.h"
-#include "mpp.h"
-
-#define MSS2_NOR_BOOT_BASE	0xff800000
-#define MSS2_NOR_BOOT_SIZE	SZ_256K
-
-/*****************************************************************************
- * Maxtor Shared Storage II Info
- ****************************************************************************/
-
-/*
- * Maxtor Shared Storage II hardware :
- * - Marvell 88F5182-A2 C500
- * - Marvell 88E1111 Gigabit Ethernet PHY
- * - RTC M41T81 (@0x68) on I2C bus
- * - 256KB NOR flash
- * - 64MB of RAM
- */
-
-/*****************************************************************************
- * 256KB NOR Flash on BOOT Device
- ****************************************************************************/
-
-static struct physmap_flash_data mss2_nor_flash_data = {
-	.width		= 1,
-};
-
-static struct resource mss2_nor_flash_resource = {
-	.flags		= IORESOURCE_MEM,
-	.start		= MSS2_NOR_BOOT_BASE,
-	.end		= MSS2_NOR_BOOT_BASE + MSS2_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device mss2_nor_flash = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &mss2_nor_flash_data,
-	},
-	.resource	= &mss2_nor_flash_resource,
-	.num_resources	= 1,
-};
-
-/****************************************************************************
- * PCI setup
- ****************************************************************************/
-static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	int irq;
-
-	/*
-	 * Check for devices with hard-wired IRQs.
-	 */
-	irq = orion5x_pci_map_irq(dev, slot, pin);
-	if (irq != -1)
-		return irq;
-
-	return -1;
-}
-
-static struct hw_pci mss2_pci __initdata = {
-	.nr_controllers = 2,
-	.setup		= orion5x_pci_sys_setup,
-	.scan		= orion5x_pci_sys_scan_bus,
-	.map_irq	= mss2_pci_map_irq,
-};
-
-static int __init mss2_pci_init(void)
-{
-	if (machine_is_mss2())
-		pci_common_init(&mss2_pci);
-
-	return 0;
-}
-subsys_initcall(mss2_pci_init);
-
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data mss2_eth_data = {
-	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data mss2_sata_data = {
-	.n_ports	= 2,
-};
-
-/*****************************************************************************
- * GPIO buttons
- ****************************************************************************/
-
-#define MSS2_GPIO_KEY_RESET	12
-#define MSS2_GPIO_KEY_POWER	11
-
-static struct gpio_keys_button mss2_buttons[] = {
-	{
-		.code		= KEY_POWER,
-		.gpio		= MSS2_GPIO_KEY_POWER,
-		.desc		= "Power",
-		.active_low	= 1,
-	}, {
-		.code		= KEY_RESTART,
-		.gpio		= MSS2_GPIO_KEY_RESET,
-		.desc		= "Reset",
-		.active_low	= 1,
-	},
-};
-
-static struct gpio_keys_platform_data mss2_button_data = {
-	.buttons	= mss2_buttons,
-	.nbuttons	= ARRAY_SIZE(mss2_buttons),
-};
-
-static struct platform_device mss2_button_device = {
-	.name		= "gpio-keys",
-	.id		= -1,
-	.dev		= {
-		.platform_data	= &mss2_button_data,
-	},
-};
-
-/*****************************************************************************
- * RTC m41t81 on I2C bus
- ****************************************************************************/
-
-#define MSS2_GPIO_RTC_IRQ	3
-
-static struct i2c_board_info __initdata mss2_i2c_rtc = {
-	I2C_BOARD_INFO("m41t81", 0x68),
-};
-
-/*****************************************************************************
- * MSS2 power off method
- ****************************************************************************/
-/*
- * On the Maxtor Shared Storage II, the shutdown process is the following :
- * - Userland modifies U-boot env to tell U-boot to go idle at next boot
- * - The board reboots
- * - U-boot starts and go into an idle mode until the user press "power"
- */
-static void mss2_power_off(void)
-{
-	u32 reg;
-
-	/*
-	 * Enable and issue soft reset
-	 */
-	reg = readl(RSTOUTn_MASK);
-	reg |= 1 << 2;
-	writel(reg, RSTOUTn_MASK);
-
-	reg = readl(CPU_SOFT_RESET);
-	reg |= 1;
-	writel(reg, CPU_SOFT_RESET);
-}
-
-/****************************************************************************
- * General Setup
- ****************************************************************************/
-static unsigned int mss2_mpp_modes[] __initdata = {
-	MPP0_GPIO,		/* Power LED */
-	MPP1_GPIO,		/* Error LED */
-	MPP2_UNUSED,
-	MPP3_GPIO,		/* RTC interrupt */
-	MPP4_GPIO,		/* HDD ind. (Single/Dual)*/
-	MPP5_GPIO,		/* HD0 5V control */
-	MPP6_GPIO,		/* HD0 12V control */
-	MPP7_GPIO,		/* HD1 5V control */
-	MPP8_GPIO,		/* HD1 12V control */
-	MPP9_UNUSED,
-	MPP10_GPIO,		/* Fan control */
-	MPP11_GPIO,		/* Power button */
-	MPP12_GPIO,		/* Reset button */
-	MPP13_UNUSED,
-	MPP14_SATA_LED,		/* SATA 0 active */
-	MPP15_SATA_LED,		/* SATA 1 active */
-	MPP16_UNUSED,
-	MPP17_UNUSED,
-	MPP18_UNUSED,
-	MPP19_UNUSED,
-	0,
-};
-
-static void __init mss2_init(void)
-{
-	/* Setup basic Orion functions. Need to be called early. */
-	orion5x_init();
-
-	orion5x_mpp_conf(mss2_mpp_modes);
-
-	/*
-	 * MPP[20] Unused
-	 * MPP[21] PCI clock
-	 * MPP[22] USB 0 over current
-	 * MPP[23] USB 1 over current
-	 */
-
-	/*
-	 * Configure peripherals.
-	 */
-	orion5x_ehci0_init();
-	orion5x_ehci1_init();
-	orion5x_eth_init(&mss2_eth_data);
-	orion5x_i2c_init();
-	orion5x_sata_init(&mss2_sata_data);
-	orion5x_uart0_init();
-	orion5x_xor_init();
-
-	mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
-				    ORION_MBUS_DEVBUS_BOOT_ATTR,
-				    MSS2_NOR_BOOT_BASE,
-				    MSS2_NOR_BOOT_SIZE);
-	platform_device_register(&mss2_nor_flash);
-
-	platform_device_register(&mss2_button_device);
-
-	if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
-		if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0)
-			mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ);
-		else
-			gpio_free(MSS2_GPIO_RTC_IRQ);
-	}
-	i2c_register_board_info(0, &mss2_i2c_rtc, 1);
-
-	/* register mss2 specific power-off method */
-	pm_power_off = mss2_power_off;
-}
-
-MACHINE_START(MSS2, "Maxtor Shared Storage II")
-	/* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
-	.atag_offset	= 0x100,
-	.init_machine	= mss2_init,
-	.map_io		= orion5x_map_io,
-	.init_early	= orion5x_init_early,
-	.init_irq	= orion5x_init_irq,
-	.init_time	= orion5x_timer_init,
-	.fixup		= tag_fixup_mem32,
-	.restart	= orion5x_restart,
-MACHINE_END