sky2: Add PCI device specfic register 4 & 5
Need to setup more PCI control control registers are on Yukon EX.
Some of these also exist on Yukon EC-U as well.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h
index b8c4a3b..3caeddf 100644
--- a/drivers/net/sky2.h
+++ b/drivers/net/sky2.h
@@ -14,6 +14,8 @@
PCI_DEV_REG3 = 0x80,
PCI_DEV_REG4 = 0x84,
PCI_DEV_REG5 = 0x88,
+ PCI_CFG_REG_0 = 0x90,
+ PCI_CFG_REG_1 = 0x94,
};
enum {
@@ -28,6 +30,7 @@
enum pci_dev_reg_1 {
PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */
PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */
+ PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */
PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */
PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */
PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */
@@ -67,6 +70,80 @@
| P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY,
};
+/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */
+enum pci_dev_reg_5 {
+ /* Bit 31..27: for A3 & later */
+ P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */
+ P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */
+ P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */
+ P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */
+ /* Bit 26..16: Release Clock on Event */
+ P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */
+ P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */
+ P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */
+ P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */
+ P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */
+ P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */
+ P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */
+ P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */
+ P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */
+ P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */
+ P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */
+
+ /* Bit 10.. 0: Mask for Gate Clock */
+ P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */
+ P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */
+ P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */
+ P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */
+ P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */
+ P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */
+ P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */
+ P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */
+ P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */
+ P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */
+ P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */
+
+ PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET |
+ P_REL_INT_FIFO_N_EMPTY |
+ P_REL_PCIE_EXIT_L1_ST |
+ P_REL_PCIE_RX_EX_IDLE |
+ P_GAT_GPHY_N_REC_PACKET |
+ P_GAT_INT_FIFO_EMPTY |
+ P_GAT_PCIE_ENTER_L1_ST |
+ P_GAT_PCIE_RX_EL_IDLE,
+};
+
+#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */
+enum pci_cfg_reg1 {
+ P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */
+ /* Bit 23..21: Release Clock on Event */
+ P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */
+ P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */
+ P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */
+ /* Bit 20..18: Gate Clock on Event */
+ P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */
+ P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */
+ P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */
+ P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */
+ P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */
+
+ P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */
+
+ P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */
+ P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */
+
+ PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST |
+ P_CF1_REL_LDR_NOT_FIN |
+ P_CF1_REL_VMAIN_AVLBL |
+ P_CF1_REL_PCIE_RESET |
+ P_CF1_GAT_LDR_NOT_FIN |
+ P_CF1_GAT_PCIE_RESET |
+ P_CF1_PRST_PHY_CLKREQ |
+ P_CF1_ENA_CFG_LDR_DONE |
+ P_CF1_ENA_TXBMU_RD_IDLE |
+ P_CF1_ENA_TXBMU_WR_IDLE,
+};
+
#define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \
PCI_STATUS_SIG_SYSTEM_ERROR | \