| /* |
| * Low-level PCI config space access for OLPC systems who lack the VSA |
| * PCI virtualization software. |
| * |
| * Copyright © 2006 Advanced Micro Devices, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| * |
| * The AMD Geode chipset (ie: GX2 processor, cs5536 I/O companion device) |
| * has some I/O functions (display, southbridge, sound, USB HCIs, etc) |
| * that more or less behave like PCI devices, but the hardware doesn't |
| * directly implement the PCI configuration space headers. AMD provides |
| * "VSA" (Virtual System Architecture) software that emulates PCI config |
| * space for these devices, by trapping I/O accesses to PCI config register |
| * (CF8/CFC) and running some code in System Management Mode interrupt state. |
| * On the OLPC platform, we don't want to use that VSA code because |
| * (a) it slows down suspend/resume, and (b) recompiling it requires special |
| * compilers that are hard to get. So instead of letting the complex VSA |
| * code simulate the PCI config registers for the on-chip devices, we |
| * just simulate them the easy way, by inserting the code into the |
| * pci_write_config and pci_read_config path. Most of the config registers |
| * are read-only anyway, so the bulk of the simulation is just table lookup. |
| */ |
| |
| #include <linux/pci.h> |
| #include <linux/init.h> |
| #include <asm/olpc.h> |
| #include <asm/geode.h> |
| #include "pci.h" |
| |
| /* |
| * In the tables below, the first two line (8 longwords) are the |
| * size masks that are used when the higher level PCI code determines |
| * the size of the region by writing ~0 to a base address register |
| * and reading back the result. |
| * |
| * The following lines are the values that are read during normal |
| * PCI config access cycles, i.e. not after just having written |
| * ~0 to a base address register. |
| */ |
| |
| static const uint32_t lxnb_hdr[] = { /* dev 1 function 0 - devfn = 8 */ |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| |
| 0x281022, 0x2200005, 0x6000021, 0x80f808, /* AMD Vendor ID */ |
| 0x0, 0x0, 0x0, 0x0, /* No virtual registers, hence no BAR */ |
| 0x0, 0x0, 0x0, 0x28100b, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| static const uint32_t gxnb_hdr[] = { /* dev 1 function 0 - devfn = 8 */ |
| 0xfffffffd, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| |
| 0x28100b, 0x2200005, 0x6000021, 0x80f808, /* NSC Vendor ID */ |
| 0xac1d, 0x0, 0x0, 0x0, /* I/O BAR - base of virtual registers */ |
| 0x0, 0x0, 0x0, 0x28100b, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| static const uint32_t lxfb_hdr[] = { /* dev 1 function 1 - devfn = 9 */ |
| 0xff000008, 0xffffc000, 0xffffc000, 0xffffc000, |
| 0xffffc000, 0x0, 0x0, 0x0, |
| |
| 0x20811022, 0x2200003, 0x3000000, 0x0, /* AMD Vendor ID */ |
| 0xfd000000, 0xfe000000, 0xfe004000, 0xfe008000, /* FB, GP, VG, DF */ |
| 0xfe00c000, 0x0, 0x0, 0x30100b, /* VIP */ |
| 0x0, 0x0, 0x0, 0x10e, /* INTA, IRQ14 for graphics accel */ |
| 0x0, 0x0, 0x0, 0x0, |
| 0x3d0, 0x3c0, 0xa0000, 0x0, /* VG IO, VG IO, EGA FB, MONO FB */ |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| static const uint32_t gxfb_hdr[] = { /* dev 1 function 1 - devfn = 9 */ |
| 0xff800008, 0xffffc000, 0xffffc000, 0xffffc000, |
| 0x0, 0x0, 0x0, 0x0, |
| |
| 0x30100b, 0x2200003, 0x3000000, 0x0, /* NSC Vendor ID */ |
| 0xfd000000, 0xfe000000, 0xfe004000, 0xfe008000, /* FB, GP, VG, DF */ |
| 0x0, 0x0, 0x0, 0x30100b, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x3d0, 0x3c0, 0xa0000, 0x0, /* VG IO, VG IO, EGA FB, MONO FB */ |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| static const uint32_t aes_hdr[] = { /* dev 1 function 2 - devfn = 0xa */ |
| 0xffffc000, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| |
| 0x20821022, 0x2a00006, 0x10100000, 0x8, /* NSC Vendor ID */ |
| 0xfe010000, 0x0, 0x0, 0x0, /* AES registers */ |
| 0x0, 0x0, 0x0, 0x20821022, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| |
| static const uint32_t isa_hdr[] = { /* dev f function 0 - devfn = 78 */ |
| 0xfffffff9, 0xffffff01, 0xffffffc1, 0xffffffe1, |
| 0xffffff81, 0xffffffc1, 0x0, 0x0, |
| |
| 0x20901022, 0x2a00049, 0x6010003, 0x802000, |
| 0x18b1, 0x1001, 0x1801, 0x1881, /* SMB-8 GPIO-256 MFGPT-64 IRQ-32 */ |
| 0x1401, 0x1841, 0x0, 0x20901022, /* PMS-128 ACPI-64 */ |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0xaa5b, /* IRQ steering */ |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| static const uint32_t ac97_hdr[] = { /* dev f function 3 - devfn = 7b */ |
| 0xffffff81, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| |
| 0x20931022, 0x2a00041, 0x4010001, 0x0, |
| 0x1481, 0x0, 0x0, 0x0, /* I/O BAR-128 */ |
| 0x0, 0x0, 0x0, 0x20931022, |
| 0x0, 0x0, 0x0, 0x205, /* IntB, IRQ5 */ |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| static const uint32_t ohci_hdr[] = { /* dev f function 4 - devfn = 7c */ |
| 0xfffff000, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| |
| 0x20941022, 0x2300006, 0xc031002, 0x0, |
| 0xfe01a000, 0x0, 0x0, 0x0, /* MEMBAR-1000 */ |
| 0x0, 0x0, 0x0, 0x20941022, |
| 0x0, 0x40, 0x0, 0x40a, /* CapPtr INT-D, IRQA */ |
| 0xc8020001, 0x0, 0x0, 0x0, /* Capabilities - 40 is R/O, |
| 44 is mask 8103 (power control) */ |
| 0x0, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| }; |
| |
| static const uint32_t ehci_hdr[] = { /* dev f function 4 - devfn = 7d */ |
| 0xfffff000, 0x0, 0x0, 0x0, |
| 0x0, 0x0, 0x0, 0x0, |
| |
| 0x20951022, 0x2300006, 0xc032002, 0x0, |
| 0xfe01b000, 0x0, 0x0, 0x0, /* MEMBAR-1000 */ |
| 0x0, 0x0, 0x0, 0x20951022, |
| 0x0, 0x40, 0x0, 0x40a, /* CapPtr INT-D, IRQA */ |
| 0xc8020001, 0x0, 0x0, 0x0, /* Capabilities - 40 is R/O, 44 is |
| mask 8103 (power control) */ |
| #if 0 |
| 0x1, 0x40080000, 0x0, 0x0, /* EECP - see EHCI spec section 2.1.7 */ |
| #endif |
| 0x01000001, 0x0, 0x0, 0x0, /* EECP - see EHCI spec section 2.1.7 */ |
| 0x2020, 0x0, 0x0, 0x0, /* (EHCI page 8) 60 SBRN (R/O), |
| 61 FLADJ (R/W), PORTWAKECAP */ |
| }; |
| |
| static uint32_t ff_loc = ~0; |
| static uint32_t zero_loc; |
| static int bar_probing; /* Set after a write of ~0 to a BAR */ |
| static int is_lx; |
| |
| #define NB_SLOT 0x1 /* Northbridge - GX chip - Device 1 */ |
| #define SB_SLOT 0xf /* Southbridge - CS5536 chip - Device F */ |
| |
| static int is_simulated(unsigned int bus, unsigned int devfn) |
| { |
| return (!bus && ((PCI_SLOT(devfn) == NB_SLOT) || |
| (PCI_SLOT(devfn) == SB_SLOT))); |
| } |
| |
| static uint32_t *hdr_addr(const uint32_t *hdr, int reg) |
| { |
| uint32_t addr; |
| |
| /* |
| * This is a little bit tricky. The header maps consist of |
| * 0x20 bytes of size masks, followed by 0x70 bytes of header data. |
| * In the normal case, when not probing a BAR's size, we want |
| * to access the header data, so we add 0x20 to the reg offset, |
| * thus skipping the size mask area. |
| * In the BAR probing case, we want to access the size mask for |
| * the BAR, so we subtract 0x10 (the config header offset for |
| * BAR0), and don't skip the size mask area. |
| */ |
| |
| addr = (uint32_t)hdr + reg + (bar_probing ? -0x10 : 0x20); |
| |
| bar_probing = 0; |
| return (uint32_t *)addr; |
| } |
| |
| static int pci_olpc_read(unsigned int seg, unsigned int bus, |
| unsigned int devfn, int reg, int len, uint32_t *value) |
| { |
| uint32_t *addr; |
| |
| /* Use the hardware mechanism for non-simulated devices */ |
| if (!is_simulated(bus, devfn)) |
| return pci_direct_conf1.read(seg, bus, devfn, reg, len, value); |
| |
| /* |
| * No device has config registers past 0x70, so we save table space |
| * by not storing entries for the nonexistent registers |
| */ |
| if (reg >= 0x70) |
| addr = &zero_loc; |
| else { |
| switch (devfn) { |
| case 0x8: |
| addr = hdr_addr(is_lx ? lxnb_hdr : gxnb_hdr, reg); |
| break; |
| case 0x9: |
| addr = hdr_addr(is_lx ? lxfb_hdr : gxfb_hdr, reg); |
| break; |
| case 0xa: |
| addr = is_lx ? hdr_addr(aes_hdr, reg) : &ff_loc; |
| break; |
| case 0x78: |
| addr = hdr_addr(isa_hdr, reg); |
| break; |
| case 0x7b: |
| addr = hdr_addr(ac97_hdr, reg); |
| break; |
| case 0x7c: |
| addr = hdr_addr(ohci_hdr, reg); |
| break; |
| case 0x7d: |
| addr = hdr_addr(ehci_hdr, reg); |
| break; |
| default: |
| addr = &ff_loc; |
| break; |
| } |
| } |
| switch (len) { |
| case 1: |
| *value = *(uint8_t *)addr; |
| break; |
| case 2: |
| *value = *(uint16_t *)addr; |
| break; |
| case 4: |
| *value = *addr; |
| break; |
| default: |
| BUG(); |
| } |
| |
| return 0; |
| } |
| |
| static int pci_olpc_write(unsigned int seg, unsigned int bus, |
| unsigned int devfn, int reg, int len, uint32_t value) |
| { |
| /* Use the hardware mechanism for non-simulated devices */ |
| if (!is_simulated(bus, devfn)) |
| return pci_direct_conf1.write(seg, bus, devfn, reg, len, value); |
| |
| /* XXX we may want to extend this to simulate EHCI power management */ |
| |
| /* |
| * Mostly we just discard writes, but if the write is a size probe |
| * (i.e. writing ~0 to a BAR), we remember it and arrange to return |
| * the appropriate size mask on the next read. This is cheating |
| * to some extent, because it depends on the fact that the next |
| * access after such a write will always be a read to the same BAR. |
| */ |
| |
| if ((reg >= 0x10) && (reg < 0x2c)) { |
| /* write is to a BAR */ |
| if (value == ~0) |
| bar_probing = 1; |
| } else { |
| /* |
| * No warning on writes to ROM BAR, CMD, LATENCY_TIMER, |
| * CACHE_LINE_SIZE, or PM registers. |
| */ |
| if ((reg != PCI_ROM_ADDRESS) && (reg != PCI_COMMAND_MASTER) && |
| (reg != PCI_LATENCY_TIMER) && |
| (reg != PCI_CACHE_LINE_SIZE) && (reg != 0x44)) |
| printk(KERN_WARNING "OLPC PCI: Config write to devfn" |
| " %x reg %x value %x\n", devfn, reg, value); |
| } |
| |
| return 0; |
| } |
| |
| static struct pci_raw_ops pci_olpc_conf = { |
| .read = pci_olpc_read, |
| .write = pci_olpc_write, |
| }; |
| |
| void __init pci_olpc_init(void) |
| { |
| if (!machine_is_olpc() || olpc_has_vsa()) |
| return; |
| |
| printk(KERN_INFO "PCI: Using configuration type OLPC\n"); |
| raw_pci_ops = &pci_olpc_conf; |
| is_lx = is_geode_lx(); |
| } |