[BATTERY] 1-Wire ds2760 chip battery driver

This is driver for batteries with ds2760 chip inside, found inside
almost every HP iPaq and HTC PDAs/phones.

Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
diff --git a/drivers/power/ds2760_battery.c b/drivers/power/ds2760_battery.c
new file mode 100644
index 0000000..00e1ea6
--- /dev/null
+++ b/drivers/power/ds2760_battery.c
@@ -0,0 +1,470 @@
+/*
+ * Driver for batteries with DS2760 chips inside.
+ *
+ * Copyright © 2007 Anton Vorontsov
+ *	       2004-2007 Matt Reimer
+ *	       2004 Szabolcs Gyurko
+ *
+ * Use consistent with the GNU GPL is permitted,
+ * provided that this copyright notice is
+ * preserved in its entirety in all copies and derived works.
+ *
+ * Author:  Anton Vorontsov <cbou@mail.ru>
+ *	    February 2007
+ *
+ *	    Matt Reimer <mreimer@vpop.net>
+ *	    April 2004, 2005, 2007
+ *
+ *	    Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
+ *	    September 2004
+ */
+
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/jiffies.h>
+#include <linux/workqueue.h>
+#include <linux/pm.h>
+#include <linux/platform_device.h>
+#include <linux/power_supply.h>
+
+#include "../w1/w1.h"
+#include "../w1/slaves/w1_ds2760.h"
+
+struct ds2760_device_info {
+	struct device *dev;
+
+	/* DS2760 data, valid after calling ds2760_battery_read_status() */
+	unsigned long update_time;	/* jiffies when data read */
+	char raw[DS2760_DATA_SIZE];	/* raw DS2760 data */
+	int voltage_raw;		/* units of 4.88 mV */
+	int voltage_uV;			/* units of µV */
+	int current_raw;		/* units of 0.625 mA */
+	int current_uA;			/* units of µA */
+	int accum_current_raw;		/* units of 0.25 mAh */
+	int accum_current_uAh;		/* units of µAh */
+	int temp_raw;			/* units of 0.125 °C */
+	int temp_C;			/* units of 0.1 °C */
+	int rated_capacity;		/* units of µAh */
+	int rem_capacity;		/* percentage */
+	int full_active_uAh;		/* units of µAh */
+	int empty_uAh;			/* units of µAh */
+	int life_sec;			/* units of seconds */
+	int charge_status;		/* POWER_SUPPLY_STATUS_* */
+
+	int full_counter;
+	struct power_supply bat;
+	struct device *w1_dev;
+	struct workqueue_struct *monitor_wqueue;
+	struct delayed_work monitor_work;
+};
+
+static unsigned int cache_time = 1000;
+module_param(cache_time, uint, 0644);
+MODULE_PARM_DESC(cache_time, "cache time in milliseconds");
+
+/* Some batteries have their rated capacity stored a N * 10 mAh, while
+ * others use an index into this table. */
+static int rated_capacities[] = {
+	0,
+	920,	/* Samsung */
+	920,	/* BYD */
+	920,	/* Lishen */
+	920,	/* NEC */
+	1440,	/* Samsung */
+	1440,	/* BYD */
+	1440,	/* Lishen */
+	1440,	/* NEC */
+	2880,	/* Samsung */
+	2880,	/* BYD */
+	2880,	/* Lishen */
+	2880	/* NEC */
+};
+
+/* array is level at temps 0°C, 10°C, 20°C, 30°C, 40°C
+ * temp is in Celsius */
+static int battery_interpolate(int array[], int temp)
+{
+	int index, dt;
+
+	if (temp <= 0)
+		return array[0];
+	if (temp >= 40)
+		return array[4];
+
+	index = temp / 10;
+	dt    = temp % 10;
+
+	return array[index] + (((array[index + 1] - array[index]) * dt) / 10);
+}
+
+static int ds2760_battery_read_status(struct ds2760_device_info *di)
+{
+	int ret, i, start, count, scale[5];
+
+	if (di->update_time && time_before(jiffies, di->update_time +
+					   msecs_to_jiffies(cache_time)))
+		return 0;
+
+	/* The first time we read the entire contents of SRAM/EEPROM,
+	 * but after that we just read the interesting bits that change. */
+	if (di->update_time == 0) {
+		start = 0;
+		count = DS2760_DATA_SIZE;
+	} else {
+		start = DS2760_VOLTAGE_MSB;
+		count = DS2760_TEMP_LSB - start + 1;
+	}
+
+	ret = w1_ds2760_read(di->w1_dev, di->raw + start, start, count);
+	if (ret != count) {
+		dev_warn(di->dev, "call to w1_ds2760_read failed (0x%p)\n",
+			 di->w1_dev);
+		return 1;
+	}
+
+	di->update_time = jiffies;
+
+	/* DS2760 reports voltage in units of 4.88mV, but the battery class
+	 * reports in units of uV, so convert by multiplying by 4880. */
+	di->voltage_raw = (di->raw[DS2760_VOLTAGE_MSB] << 3) |
+			  (di->raw[DS2760_VOLTAGE_LSB] >> 5);
+	di->voltage_uV = di->voltage_raw * 4880;
+
+	/* DS2760 reports current in signed units of 0.625mA, but the battery
+	 * class reports in units of µA, so convert by multiplying by 625. */
+	di->current_raw =
+	    (((signed char)di->raw[DS2760_CURRENT_MSB]) << 5) |
+			  (di->raw[DS2760_CURRENT_LSB] >> 3);
+	di->current_uA = di->current_raw * 625;
+
+	/* DS2760 reports accumulated current in signed units of 0.25mAh. */
+	di->accum_current_raw =
+	    (((signed char)di->raw[DS2760_CURRENT_ACCUM_MSB]) << 8) |
+			   di->raw[DS2760_CURRENT_ACCUM_LSB];
+	di->accum_current_uAh = di->accum_current_raw * 250;
+
+	/* DS2760 reports temperature in signed units of 0.125°C, but the
+	 * battery class reports in units of 1/10 °C, so we convert by
+	 * multiplying by .125 * 10 = 1.25. */
+	di->temp_raw = (((signed char)di->raw[DS2760_TEMP_MSB]) << 3) |
+				     (di->raw[DS2760_TEMP_LSB] >> 5);
+	di->temp_C = di->temp_raw + (di->temp_raw / 4);
+
+	/* At least some battery monitors (e.g. HP iPAQ) store the battery's
+	 * maximum rated capacity. */
+	if (di->raw[DS2760_RATED_CAPACITY] < ARRAY_SIZE(rated_capacities))
+		di->rated_capacity = rated_capacities[
+			(unsigned int)di->raw[DS2760_RATED_CAPACITY]];
+	else
+		di->rated_capacity = di->raw[DS2760_RATED_CAPACITY] * 10;
+
+	di->rated_capacity *= 1000; /* convert to µAh */
+
+	/* Calculate the full level at the present temperature. */
+	di->full_active_uAh = di->raw[DS2760_ACTIVE_FULL] << 8 |
+			      di->raw[DS2760_ACTIVE_FULL + 1];
+
+	scale[0] = di->raw[DS2760_ACTIVE_FULL] << 8 |
+		   di->raw[DS2760_ACTIVE_FULL + 1];
+	for (i = 1; i < 5; i++)
+		scale[i] = scale[i - 1] + di->raw[DS2760_ACTIVE_FULL + 2 + i];
+
+	di->full_active_uAh = battery_interpolate(scale, di->temp_C / 10);
+	di->full_active_uAh *= 1000; /* convert to µAh */
+
+	/* Calculate the empty level at the present temperature. */
+	scale[4] = di->raw[DS2760_ACTIVE_EMPTY + 4];
+	for (i = 3; i >= 0; i--)
+		scale[i] = scale[i + 1] + di->raw[DS2760_ACTIVE_EMPTY + i];
+
+	di->empty_uAh = battery_interpolate(scale, di->temp_C / 10);
+	di->empty_uAh *= 1000; /* convert to µAh */
+
+	/* From Maxim Application Note 131: remaining capacity =
+	 * ((ICA - Empty Value) / (Full Value - Empty Value)) x 100% */
+	di->rem_capacity = ((di->accum_current_uAh - di->empty_uAh) * 100L) /
+			    (di->full_active_uAh - di->empty_uAh);
+
+	if (di->rem_capacity < 0)
+		di->rem_capacity = 0;
+	if (di->rem_capacity > 100)
+		di->rem_capacity = 100;
+
+	if (di->current_uA)
+		di->life_sec = -((di->accum_current_uAh - di->empty_uAh) *
+				 3600L) / di->current_uA;
+	else
+		di->life_sec = 0;
+
+	return 0;
+}
+
+static void ds2760_battery_update_status(struct ds2760_device_info *di)
+{
+	int old_charge_status = di->charge_status;
+
+	ds2760_battery_read_status(di);
+
+	if (di->charge_status == POWER_SUPPLY_STATUS_UNKNOWN)
+		di->full_counter = 0;
+
+	if (power_supply_am_i_supplied(&di->bat)) {
+		if (di->current_uA > 10000) {
+			di->charge_status = POWER_SUPPLY_STATUS_CHARGING;
+			di->full_counter = 0;
+		} else if (di->current_uA < -5000) {
+			if (di->charge_status != POWER_SUPPLY_STATUS_NOT_CHARGING)
+				dev_notice(di->dev, "not enough power to "
+					   "charge\n");
+			di->charge_status = POWER_SUPPLY_STATUS_NOT_CHARGING;
+			di->full_counter = 0;
+		} else if (di->current_uA < 10000 &&
+			    di->charge_status != POWER_SUPPLY_STATUS_FULL) {
+
+			/* Don't consider the battery to be full unless
+			 * we've seen the current < 10 mA at least two
+			 * consecutive times. */
+
+			di->full_counter++;
+
+			if (di->full_counter < 2) {
+				di->charge_status = POWER_SUPPLY_STATUS_CHARGING;
+			} else {
+				unsigned char acr[2];
+				int acr_val;
+
+				/* acr is in units of 0.25 mAh */
+				acr_val = di->full_active_uAh * 4L / 1000;
+
+				acr[0] = acr_val >> 8;
+				acr[1] = acr_val & 0xff;
+
+				if (w1_ds2760_write(di->w1_dev, acr,
+				    DS2760_CURRENT_ACCUM_MSB, 2) < 2)
+					dev_warn(di->dev,
+						 "ACR reset failed\n");
+
+				di->charge_status = POWER_SUPPLY_STATUS_FULL;
+			}
+		}
+	} else {
+		di->charge_status = POWER_SUPPLY_STATUS_DISCHARGING;
+		di->full_counter = 0;
+	}
+
+	if (di->charge_status != old_charge_status)
+		power_supply_changed(&di->bat);
+
+	return;
+}
+
+static void ds2760_battery_work(struct work_struct *work)
+{
+	struct ds2760_device_info *di = container_of(work,
+		struct ds2760_device_info, monitor_work.work);
+	const int interval = HZ * 60;
+
+	dev_dbg(di->dev, "%s\n", __FUNCTION__);
+
+	ds2760_battery_update_status(di);
+	queue_delayed_work(di->monitor_wqueue, &di->monitor_work, interval);
+
+	return;
+}
+
+#define to_ds2760_device_info(x) container_of((x), struct ds2760_device_info, \
+					      bat);
+
+static void ds2760_battery_external_power_changed(struct power_supply *psy)
+{
+	struct ds2760_device_info *di = to_ds2760_device_info(psy);
+
+	dev_dbg(di->dev, "%s\n", __FUNCTION__);
+
+	cancel_delayed_work(&di->monitor_work);
+	queue_delayed_work(di->monitor_wqueue, &di->monitor_work, HZ/10);
+
+	return;
+}
+
+static int ds2760_battery_get_property(struct power_supply *psy,
+				       enum power_supply_property psp,
+				       union power_supply_propval *val)
+{
+	struct ds2760_device_info *di = to_ds2760_device_info(psy);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_STATUS:
+		val->intval = di->charge_status;
+		return 0;
+	default:
+		break;
+	}
+
+	ds2760_battery_read_status(di);
+
+	switch (psp) {
+	case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+		val->intval = di->voltage_uV;
+		break;
+	case POWER_SUPPLY_PROP_CURRENT_NOW:
+		val->intval = di->current_uA;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
+		val->intval = di->rated_capacity;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_FULL:
+		val->intval = di->full_active_uAh;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_EMPTY:
+		val->intval = di->empty_uAh;
+		break;
+	case POWER_SUPPLY_PROP_CHARGE_NOW:
+		val->intval = di->accum_current_uAh;
+		break;
+	case POWER_SUPPLY_PROP_TEMP:
+		val->intval = di->temp_C;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static enum power_supply_property ds2760_battery_props[] = {
+	POWER_SUPPLY_PROP_STATUS,
+	POWER_SUPPLY_PROP_VOLTAGE_NOW,
+	POWER_SUPPLY_PROP_CURRENT_NOW,
+	POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN,
+	POWER_SUPPLY_PROP_CHARGE_FULL,
+	POWER_SUPPLY_PROP_CHARGE_EMPTY,
+	POWER_SUPPLY_PROP_CHARGE_NOW,
+	POWER_SUPPLY_PROP_TEMP,
+};
+
+static int ds2760_battery_probe(struct platform_device *pdev)
+{
+	int retval = 0;
+	struct ds2760_device_info *di;
+	struct ds2760_platform_data *pdata;
+
+	di = kzalloc(sizeof(*di), GFP_KERNEL);
+	if (!di) {
+		retval = -ENOMEM;
+		goto di_alloc_failed;
+	}
+
+	platform_set_drvdata(pdev, di);
+
+	pdata = pdev->dev.platform_data;
+	di->dev		= &pdev->dev;
+	di->w1_dev	     = pdev->dev.parent;
+	di->bat.name	   = pdev->dev.bus_id;
+	di->bat.type	   = POWER_SUPPLY_TYPE_BATTERY;
+	di->bat.properties     = ds2760_battery_props;
+	di->bat.num_properties = ARRAY_SIZE(ds2760_battery_props);
+	di->bat.get_property   = ds2760_battery_get_property;
+	di->bat.external_power_changed =
+				  ds2760_battery_external_power_changed;
+
+	di->charge_status = POWER_SUPPLY_STATUS_UNKNOWN;
+
+	retval = power_supply_register(&pdev->dev, &di->bat);
+	if (retval) {
+		dev_err(di->dev, "failed to register battery");
+		goto batt_failed;
+	}
+
+	INIT_DELAYED_WORK(&di->monitor_work, ds2760_battery_work);
+	di->monitor_wqueue = create_singlethread_workqueue(pdev->dev.bus_id);
+	if (!di->monitor_wqueue) {
+		retval = -ESRCH;
+		goto workqueue_failed;
+	}
+	queue_delayed_work(di->monitor_wqueue, &di->monitor_work, HZ * 1);
+
+	goto success;
+
+workqueue_failed:
+	power_supply_unregister(&di->bat);
+batt_failed:
+	kfree(di);
+di_alloc_failed:
+success:
+	return retval;
+}
+
+static int ds2760_battery_remove(struct platform_device *pdev)
+{
+	struct ds2760_device_info *di = platform_get_drvdata(pdev);
+
+	cancel_rearming_delayed_workqueue(di->monitor_wqueue,
+					  &di->monitor_work);
+	destroy_workqueue(di->monitor_wqueue);
+	power_supply_unregister(&di->bat);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+
+static int ds2760_battery_suspend(struct platform_device *pdev,
+				  pm_message_t state)
+{
+	struct ds2760_device_info *di = platform_get_drvdata(pdev);
+
+	di->charge_status = POWER_SUPPLY_STATUS_UNKNOWN;
+
+	return 0;
+}
+
+static int ds2760_battery_resume(struct platform_device *pdev)
+{
+	struct ds2760_device_info *di = platform_get_drvdata(pdev);
+
+	di->charge_status = POWER_SUPPLY_STATUS_UNKNOWN;
+	power_supply_changed(&di->bat);
+
+	cancel_delayed_work(&di->monitor_work);
+	queue_delayed_work(di->monitor_wqueue, &di->monitor_work, HZ);
+
+	return 0;
+}
+
+#else
+
+#define ds2760_battery_suspend NULL
+#define ds2760_battery_resume NULL
+
+#endif /* CONFIG_PM */
+
+static struct platform_driver ds2760_battery_driver = {
+	.driver = {
+		.name = "ds2760-battery",
+	},
+	.probe	  = ds2760_battery_probe,
+	.remove   = ds2760_battery_remove,
+	.suspend  = ds2760_battery_suspend,
+	.resume	  = ds2760_battery_resume,
+};
+
+static int __init ds2760_battery_init(void)
+{
+	return platform_driver_register(&ds2760_battery_driver);
+}
+
+static void __exit ds2760_battery_exit(void)
+{
+	platform_driver_unregister(&ds2760_battery_driver);
+	return;
+}
+
+module_init(ds2760_battery_init);
+module_exit(ds2760_battery_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>, "
+	      "Matt Reimer <mreimer@vpop.net>, "
+	      "Anton Vorontsov <cbou@mail.ru>");
+MODULE_DESCRIPTION("ds2760 battery driver");