[media] Add initial support for Terratec H5
Not working yet. There are some fixes at the DRX-K that are needed
for it to work.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
diff --git a/drivers/media/video/em28xx/em28xx-cards.c b/drivers/media/video/em28xx/em28xx-cards.c
index c892a1e..cc0b9a3 100644
--- a/drivers/media/video/em28xx/em28xx-cards.c
+++ b/drivers/media/video/em28xx/em28xx-cards.c
@@ -300,6 +300,23 @@
{-1, -1, -1, -1},
};
+#if 0
+static struct em28xx_reg_seq terratec_h5_gpio[] = {
+ {EM28XX_R08_GPIO, 0xff, 0xff, 10},
+ {EM2874_R80_GPIO, 0xf6, 0xff, 100},
+ {EM2874_R80_GPIO, 0xf2, 0xff, 50},
+ {EM2874_R80_GPIO, 0xf6, 0xff, 50},
+ { -1, -1, -1, -1},
+};
+
+static struct em28xx_reg_seq terratec_h5_digital[] = {
+ {EM2874_R80_GPIO, 0xf6, 0xff, 10},
+ {EM2874_R80_GPIO, 0xe6, 0xff, 100},
+ {EM2874_R80_GPIO, 0xa6, 0xff, 10},
+ { -1, -1, -1, -1},
+};
+#endif
+
/*
* Board definitions
*/
@@ -843,6 +860,19 @@
.gpio = terratec_cinergy_USB_XS_FR_analog,
} },
},
+ [EM2884_BOARD_TERRATEC_H5] = {
+ .name = "Terratec Cinergy H5",
+ .has_dvb = 1,
+#if 0
+ .tuner_type = TUNER_PHILIPS_TDA8290,
+ .tuner_addr = 0x41,
+ .dvb_gpio = terratec_h5_digital, /* FIXME: probably wrong */
+ .tuner_gpio = terratec_h5_gpio,
+#endif
+ .i2c_speed = EM2874_I2C_SECONDARY_BUS_SELECT |
+ EM28XX_I2C_CLK_WAIT_ENABLE |
+ EM28XX_I2C_FREQ_400_KHZ,
+ },
[EM2880_BOARD_HAUPPAUGE_WINTV_HVR_900] = {
.name = "Hauppauge WinTV HVR 900",
.tda9887_conf = TDA9887_PRESENT,
@@ -1855,6 +1885,8 @@
.driver_info = EM2882_BOARD_TERRATEC_HYBRID_XS },
{ USB_DEVICE(0x0ccd, 0x0043),
.driver_info = EM2870_BOARD_TERRATEC_XS },
+ { USB_DEVICE(0x0ccd, 0x10a2),
+ .driver_info = EM2884_BOARD_TERRATEC_H5 },
{ USB_DEVICE(0x0ccd, 0x0047),
.driver_info = EM2880_BOARD_TERRATEC_PRODIGY_XS },
{ USB_DEVICE(0x0ccd, 0x0084),
@@ -2840,6 +2872,11 @@
em28xx_info("chip ID is em2882/em2883\n");
dev->wait_after_write = 0;
break;
+ case CHIP_ID_EM2884:
+ em28xx_info("chip ID is em2884\n");
+ dev->reg_gpio_num = EM2874_R80_GPIO;
+ dev->wait_after_write = 0;
+ break;
default:
em28xx_info("em28xx chip ID = %d\n", dev->chip_id);
}