ath9k: Code scrub
Merge core.c and base.c
Remove Antenna Diversity (unused now).
Remove unused chainmask handling code.
Comment, indentation scrub.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/drivers/net/wireless/ath9k/main.c b/drivers/net/wireless/ath9k/main.c
index 54d89ab..f226a4d 100644
--- a/drivers/net/wireless/ath9k/main.c
+++ b/drivers/net/wireless/ath9k/main.c
@@ -14,8 +14,6 @@
* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
*/
-/* mac80211 and PCI callbacks */
-
#include <linux/nl80211.h>
#include "core.h"
#include "reg.h"
@@ -40,6 +38,580 @@
static void ath_detach(struct ath_softc *sc);
+/* return bus cachesize in 4B word units */
+
+static void bus_read_cachesize(struct ath_softc *sc, int *csz)
+{
+ u8 u8tmp;
+
+ pci_read_config_byte(sc->pdev, PCI_CACHE_LINE_SIZE, (u8 *)&u8tmp);
+ *csz = (int)u8tmp;
+
+ /*
+ * This check was put in to avoid "unplesant" consequences if
+ * the bootrom has not fully initialized all PCI devices.
+ * Sometimes the cache line size register is not set
+ */
+
+ if (*csz == 0)
+ *csz = DEFAULT_CACHELINE >> 2; /* Use the default size */
+}
+
+static void ath_setcurmode(struct ath_softc *sc, enum wireless_mode mode)
+{
+ sc->sc_curmode = mode;
+ /*
+ * All protection frames are transmited at 2Mb/s for
+ * 11g, otherwise at 1Mb/s.
+ * XXX select protection rate index from rate table.
+ */
+ sc->sc_protrix = (mode == ATH9K_MODE_11G ? 1 : 0);
+}
+
+static enum wireless_mode ath_chan2mode(struct ath9k_channel *chan)
+{
+ if (chan->chanmode == CHANNEL_A)
+ return ATH9K_MODE_11A;
+ else if (chan->chanmode == CHANNEL_G)
+ return ATH9K_MODE_11G;
+ else if (chan->chanmode == CHANNEL_B)
+ return ATH9K_MODE_11B;
+ else if (chan->chanmode == CHANNEL_A_HT20)
+ return ATH9K_MODE_11NA_HT20;
+ else if (chan->chanmode == CHANNEL_G_HT20)
+ return ATH9K_MODE_11NG_HT20;
+ else if (chan->chanmode == CHANNEL_A_HT40PLUS)
+ return ATH9K_MODE_11NA_HT40PLUS;
+ else if (chan->chanmode == CHANNEL_A_HT40MINUS)
+ return ATH9K_MODE_11NA_HT40MINUS;
+ else if (chan->chanmode == CHANNEL_G_HT40PLUS)
+ return ATH9K_MODE_11NG_HT40PLUS;
+ else if (chan->chanmode == CHANNEL_G_HT40MINUS)
+ return ATH9K_MODE_11NG_HT40MINUS;
+
+ WARN_ON(1); /* should not get here */
+
+ return ATH9K_MODE_11B;
+}
+
+static void ath_update_txpow(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ u32 txpow;
+
+ if (sc->sc_curtxpow != sc->sc_config.txpowlimit) {
+ ath9k_hw_set_txpowerlimit(ah, sc->sc_config.txpowlimit);
+ /* read back in case value is clamped */
+ ath9k_hw_getcapability(ah, ATH9K_CAP_TXPOW, 1, &txpow);
+ sc->sc_curtxpow = txpow;
+ }
+}
+
+static u8 parse_mpdudensity(u8 mpdudensity)
+{
+ /*
+ * 802.11n D2.0 defined values for "Minimum MPDU Start Spacing":
+ * 0 for no restriction
+ * 1 for 1/4 us
+ * 2 for 1/2 us
+ * 3 for 1 us
+ * 4 for 2 us
+ * 5 for 4 us
+ * 6 for 8 us
+ * 7 for 16 us
+ */
+ switch (mpdudensity) {
+ case 0:
+ return 0;
+ case 1:
+ case 2:
+ case 3:
+ /* Our lower layer calculations limit our precision to
+ 1 microsecond */
+ return 1;
+ case 4:
+ return 2;
+ case 5:
+ return 4;
+ case 6:
+ return 8;
+ case 7:
+ return 16;
+ default:
+ return 0;
+ }
+}
+
+static void ath_setup_rates(struct ath_softc *sc, enum ieee80211_band band)
+{
+ struct ath_rate_table *rate_table = NULL;
+ struct ieee80211_supported_band *sband;
+ struct ieee80211_rate *rate;
+ int i, maxrates;
+
+ switch (band) {
+ case IEEE80211_BAND_2GHZ:
+ rate_table = sc->hw_rate_table[ATH9K_MODE_11G];
+ break;
+ case IEEE80211_BAND_5GHZ:
+ rate_table = sc->hw_rate_table[ATH9K_MODE_11A];
+ break;
+ default:
+ break;
+ }
+
+ if (rate_table == NULL)
+ return;
+
+ sband = &sc->sbands[band];
+ rate = sc->rates[band];
+
+ if (rate_table->rate_cnt > ATH_RATE_MAX)
+ maxrates = ATH_RATE_MAX;
+ else
+ maxrates = rate_table->rate_cnt;
+
+ for (i = 0; i < maxrates; i++) {
+ rate[i].bitrate = rate_table->info[i].ratekbps / 100;
+ rate[i].hw_value = rate_table->info[i].ratecode;
+ sband->n_bitrates++;
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Rate: %2dMbps, ratecode: %2d\n",
+ __func__, rate[i].bitrate / 10, rate[i].hw_value);
+ }
+}
+
+static int ath_setup_channels(struct ath_softc *sc)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int nchan, i, a = 0, b = 0;
+ u8 regclassids[ATH_REGCLASSIDS_MAX];
+ u32 nregclass = 0;
+ struct ieee80211_supported_band *band_2ghz;
+ struct ieee80211_supported_band *band_5ghz;
+ struct ieee80211_channel *chan_2ghz;
+ struct ieee80211_channel *chan_5ghz;
+ struct ath9k_channel *c;
+
+ /* Fill in ah->ah_channels */
+ if (!ath9k_regd_init_channels(ah, ATH_CHAN_MAX, (u32 *)&nchan,
+ regclassids, ATH_REGCLASSIDS_MAX,
+ &nregclass, CTRY_DEFAULT, false, 1)) {
+ u32 rd = ah->ah_currentRD;
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to collect channel list; "
+ "regdomain likely %u country code %u\n",
+ __func__, rd, CTRY_DEFAULT);
+ return -EINVAL;
+ }
+
+ band_2ghz = &sc->sbands[IEEE80211_BAND_2GHZ];
+ band_5ghz = &sc->sbands[IEEE80211_BAND_5GHZ];
+ chan_2ghz = sc->channels[IEEE80211_BAND_2GHZ];
+ chan_5ghz = sc->channels[IEEE80211_BAND_5GHZ];
+
+ for (i = 0; i < nchan; i++) {
+ c = &ah->ah_channels[i];
+ if (IS_CHAN_2GHZ(c)) {
+ chan_2ghz[a].band = IEEE80211_BAND_2GHZ;
+ chan_2ghz[a].center_freq = c->channel;
+ chan_2ghz[a].max_power = c->maxTxPower;
+
+ if (c->privFlags & CHANNEL_DISALLOW_ADHOC)
+ chan_2ghz[a].flags |= IEEE80211_CHAN_NO_IBSS;
+ if (c->channelFlags & CHANNEL_PASSIVE)
+ chan_2ghz[a].flags |= IEEE80211_CHAN_PASSIVE_SCAN;
+
+ band_2ghz->n_channels = ++a;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: 2MHz channel: %d, "
+ "channelFlags: 0x%x\n",
+ __func__, c->channel, c->channelFlags);
+ } else if (IS_CHAN_5GHZ(c)) {
+ chan_5ghz[b].band = IEEE80211_BAND_5GHZ;
+ chan_5ghz[b].center_freq = c->channel;
+ chan_5ghz[b].max_power = c->maxTxPower;
+
+ if (c->privFlags & CHANNEL_DISALLOW_ADHOC)
+ chan_5ghz[b].flags |= IEEE80211_CHAN_NO_IBSS;
+ if (c->channelFlags & CHANNEL_PASSIVE)
+ chan_5ghz[b].flags |= IEEE80211_CHAN_PASSIVE_SCAN;
+
+ band_5ghz->n_channels = ++b;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: 5MHz channel: %d, "
+ "channelFlags: 0x%x\n",
+ __func__, c->channel, c->channelFlags);
+ }
+ }
+
+ return 0;
+}
+
+/*
+ * Set/change channels. If the channel is really being changed, it's done
+ * by reseting the chip. To accomplish this we must first cleanup any pending
+ * DMA, then restart stuff.
+*/
+static int ath_set_channel(struct ath_softc *sc, struct ath9k_channel *hchan)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ bool fastcc = true, stopped;
+
+ if (sc->sc_flags & SC_OP_INVALID)
+ return -EIO;
+
+ DPRINTF(sc, ATH_DBG_CONFIG,
+ "%s: %u (%u MHz) -> %u (%u MHz), cflags:%x\n",
+ __func__,
+ ath9k_hw_mhz2ieee(ah, sc->sc_ah->ah_curchan->channel,
+ sc->sc_ah->ah_curchan->channelFlags),
+ sc->sc_ah->ah_curchan->channel,
+ ath9k_hw_mhz2ieee(ah, hchan->channel, hchan->channelFlags),
+ hchan->channel, hchan->channelFlags);
+
+ if (hchan->channel != sc->sc_ah->ah_curchan->channel ||
+ hchan->channelFlags != sc->sc_ah->ah_curchan->channelFlags ||
+ (sc->sc_flags & SC_OP_CHAINMASK_UPDATE) ||
+ (sc->sc_flags & SC_OP_FULL_RESET)) {
+ int status;
+ /*
+ * This is only performed if the channel settings have
+ * actually changed.
+ *
+ * To switch channels clear any pending DMA operations;
+ * wait long enough for the RX fifo to drain, reset the
+ * hardware at the new frequency, and then re-enable
+ * the relevant bits of the h/w.
+ */
+ ath9k_hw_set_interrupts(ah, 0); /* disable interrupts */
+ ath_draintxq(sc, false); /* clear pending tx frames */
+ stopped = ath_stoprecv(sc); /* turn off frame recv */
+
+ /* XXX: do not flush receive queue here. We don't want
+ * to flush data frames already in queue because of
+ * changing channel. */
+
+ if (!stopped || (sc->sc_flags & SC_OP_FULL_RESET))
+ fastcc = false;
+
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, hchan, sc->sc_ht_info.tx_chan_width,
+ sc->sc_tx_chainmask, sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing, fastcc, &status)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset channel %u (%uMhz) "
+ "flags 0x%x hal status %u\n", __func__,
+ ath9k_hw_mhz2ieee(ah, hchan->channel,
+ hchan->channelFlags),
+ hchan->channel, hchan->channelFlags, status);
+ spin_unlock_bh(&sc->sc_resetlock);
+ return -EIO;
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ sc->sc_flags &= ~SC_OP_CHAINMASK_UPDATE;
+ sc->sc_flags &= ~SC_OP_FULL_RESET;
+
+ if (ath_startrecv(sc) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to restart recv logic\n", __func__);
+ return -EIO;
+ }
+
+ ath_setcurmode(sc, ath_chan2mode(hchan));
+ ath_update_txpow(sc);
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ }
+ return 0;
+}
+
+/*
+ * This routine performs the periodic noise floor calibration function
+ * that is used to adjust and optimize the chip performance. This
+ * takes environmental changes (location, temperature) into account.
+ * When the task is complete, it reschedules itself depending on the
+ * appropriate interval that was calculated.
+ */
+static void ath_ani_calibrate(unsigned long data)
+{
+ struct ath_softc *sc;
+ struct ath_hal *ah;
+ bool longcal = false;
+ bool shortcal = false;
+ bool aniflag = false;
+ unsigned int timestamp = jiffies_to_msecs(jiffies);
+ u32 cal_interval;
+
+ sc = (struct ath_softc *)data;
+ ah = sc->sc_ah;
+
+ /*
+ * don't calibrate when we're scanning.
+ * we are most likely not on our home channel.
+ */
+ if (sc->rx_filter & FIF_BCN_PRBRESP_PROMISC)
+ return;
+
+ /* Long calibration runs independently of short calibration. */
+ if ((timestamp - sc->sc_ani.sc_longcal_timer) >= ATH_LONG_CALINTERVAL) {
+ longcal = true;
+ DPRINTF(sc, ATH_DBG_ANI, "%s: longcal @%lu\n",
+ __func__, jiffies);
+ sc->sc_ani.sc_longcal_timer = timestamp;
+ }
+
+ /* Short calibration applies only while sc_caldone is false */
+ if (!sc->sc_ani.sc_caldone) {
+ if ((timestamp - sc->sc_ani.sc_shortcal_timer) >=
+ ATH_SHORT_CALINTERVAL) {
+ shortcal = true;
+ DPRINTF(sc, ATH_DBG_ANI, "%s: shortcal @%lu\n",
+ __func__, jiffies);
+ sc->sc_ani.sc_shortcal_timer = timestamp;
+ sc->sc_ani.sc_resetcal_timer = timestamp;
+ }
+ } else {
+ if ((timestamp - sc->sc_ani.sc_resetcal_timer) >=
+ ATH_RESTART_CALINTERVAL) {
+ ath9k_hw_reset_calvalid(ah, ah->ah_curchan,
+ &sc->sc_ani.sc_caldone);
+ if (sc->sc_ani.sc_caldone)
+ sc->sc_ani.sc_resetcal_timer = timestamp;
+ }
+ }
+
+ /* Verify whether we must check ANI */
+ if ((timestamp - sc->sc_ani.sc_checkani_timer) >=
+ ATH_ANI_POLLINTERVAL) {
+ aniflag = true;
+ sc->sc_ani.sc_checkani_timer = timestamp;
+ }
+
+ /* Skip all processing if there's nothing to do. */
+ if (longcal || shortcal || aniflag) {
+ /* Call ANI routine if necessary */
+ if (aniflag)
+ ath9k_hw_ani_monitor(ah, &sc->sc_halstats,
+ ah->ah_curchan);
+
+ /* Perform calibration if necessary */
+ if (longcal || shortcal) {
+ bool iscaldone = false;
+
+ if (ath9k_hw_calibrate(ah, ah->ah_curchan,
+ sc->sc_rx_chainmask, longcal,
+ &iscaldone)) {
+ if (longcal)
+ sc->sc_ani.sc_noise_floor =
+ ath9k_hw_getchan_noise(ah,
+ ah->ah_curchan);
+
+ DPRINTF(sc, ATH_DBG_ANI,
+ "%s: calibrate chan %u/%x nf: %d\n",
+ __func__,
+ ah->ah_curchan->channel,
+ ah->ah_curchan->channelFlags,
+ sc->sc_ani.sc_noise_floor);
+ } else {
+ DPRINTF(sc, ATH_DBG_ANY,
+ "%s: calibrate chan %u/%x failed\n",
+ __func__,
+ ah->ah_curchan->channel,
+ ah->ah_curchan->channelFlags);
+ }
+ sc->sc_ani.sc_caldone = iscaldone;
+ }
+ }
+
+ /*
+ * Set timer interval based on previous results.
+ * The interval must be the shortest necessary to satisfy ANI,
+ * short calibration and long calibration.
+ */
+
+ cal_interval = ATH_ANI_POLLINTERVAL;
+ if (!sc->sc_ani.sc_caldone)
+ cal_interval = min(cal_interval, (u32)ATH_SHORT_CALINTERVAL);
+
+ mod_timer(&sc->sc_ani.timer, jiffies + msecs_to_jiffies(cal_interval));
+}
+
+/*
+ * Update tx/rx chainmask. For legacy association,
+ * hard code chainmask to 1x1, for 11n association, use
+ * the chainmask configuration.
+ */
+static void ath_update_chainmask(struct ath_softc *sc, int is_ht)
+{
+ sc->sc_flags |= SC_OP_CHAINMASK_UPDATE;
+ if (is_ht) {
+ sc->sc_tx_chainmask = sc->sc_ah->ah_caps.tx_chainmask;
+ sc->sc_rx_chainmask = sc->sc_ah->ah_caps.rx_chainmask;
+ } else {
+ sc->sc_tx_chainmask = 1;
+ sc->sc_rx_chainmask = 1;
+ }
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: tx chmask: %d, rx chmask: %d\n",
+ __func__, sc->sc_tx_chainmask, sc->sc_rx_chainmask);
+}
+
+static void ath_node_attach(struct ath_softc *sc, struct ieee80211_sta *sta)
+{
+ struct ath_node *an;
+
+ an = (struct ath_node *)sta->drv_priv;
+
+ if (sc->sc_flags & SC_OP_TXAGGR)
+ ath_tx_node_init(sc, an);
+
+ an->maxampdu = 1 << (IEEE80211_HTCAP_MAXRXAMPDU_FACTOR +
+ sta->ht_cap.ampdu_factor);
+ an->mpdudensity = parse_mpdudensity(sta->ht_cap.ampdu_density);
+}
+
+static void ath_node_detach(struct ath_softc *sc, struct ieee80211_sta *sta)
+{
+ struct ath_node *an = (struct ath_node *)sta->drv_priv;
+
+ if (sc->sc_flags & SC_OP_TXAGGR)
+ ath_tx_node_cleanup(sc, an);
+}
+
+static void ath9k_tasklet(unsigned long data)
+{
+ struct ath_softc *sc = (struct ath_softc *)data;
+ u32 status = sc->sc_intrstatus;
+
+ if (status & ATH9K_INT_FATAL) {
+ /* need a chip reset */
+ ath_reset(sc, false);
+ return;
+ } else {
+
+ if (status &
+ (ATH9K_INT_RX | ATH9K_INT_RXEOL | ATH9K_INT_RXORN)) {
+ spin_lock_bh(&sc->sc_rxflushlock);
+ ath_rx_tasklet(sc, 0);
+ spin_unlock_bh(&sc->sc_rxflushlock);
+ }
+ /* XXX: optimize this */
+ if (status & ATH9K_INT_TX)
+ ath_tx_tasklet(sc);
+ }
+
+ /* re-enable hardware interrupt */
+ ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask);
+}
+
+static irqreturn_t ath_isr(int irq, void *dev)
+{
+ struct ath_softc *sc = dev;
+ struct ath_hal *ah = sc->sc_ah;
+ enum ath9k_int status;
+ bool sched = false;
+
+ do {
+ if (sc->sc_flags & SC_OP_INVALID) {
+ /*
+ * The hardware is not ready/present, don't
+ * touch anything. Note this can happen early
+ * on if the IRQ is shared.
+ */
+ return IRQ_NONE;
+ }
+ if (!ath9k_hw_intrpend(ah)) { /* shared irq, not for us */
+ return IRQ_NONE;
+ }
+
+ /*
+ * Figure out the reason(s) for the interrupt. Note
+ * that the hal returns a pseudo-ISR that may include
+ * bits we haven't explicitly enabled so we mask the
+ * value to insure we only process bits we requested.
+ */
+ ath9k_hw_getisr(ah, &status); /* NB: clears ISR too */
+
+ status &= sc->sc_imask; /* discard unasked-for bits */
+
+ /*
+ * If there are no status bits set, then this interrupt was not
+ * for me (should have been caught above).
+ */
+ if (!status)
+ return IRQ_NONE;
+
+ sc->sc_intrstatus = status;
+
+ if (status & ATH9K_INT_FATAL) {
+ /* need a chip reset */
+ sched = true;
+ } else if (status & ATH9K_INT_RXORN) {
+ /* need a chip reset */
+ sched = true;
+ } else {
+ if (status & ATH9K_INT_SWBA) {
+ /* schedule a tasklet for beacon handling */
+ tasklet_schedule(&sc->bcon_tasklet);
+ }
+ if (status & ATH9K_INT_RXEOL) {
+ /*
+ * NB: the hardware should re-read the link when
+ * RXE bit is written, but it doesn't work
+ * at least on older hardware revs.
+ */
+ sched = true;
+ }
+
+ if (status & ATH9K_INT_TXURN)
+ /* bump tx trigger level */
+ ath9k_hw_updatetxtriglevel(ah, true);
+ /* XXX: optimize this */
+ if (status & ATH9K_INT_RX)
+ sched = true;
+ if (status & ATH9K_INT_TX)
+ sched = true;
+ if (status & ATH9K_INT_BMISS)
+ sched = true;
+ /* carrier sense timeout */
+ if (status & ATH9K_INT_CST)
+ sched = true;
+ if (status & ATH9K_INT_MIB) {
+ /*
+ * Disable interrupts until we service the MIB
+ * interrupt; otherwise it will continue to
+ * fire.
+ */
+ ath9k_hw_set_interrupts(ah, 0);
+ /*
+ * Let the hal handle the event. We assume
+ * it will clear whatever condition caused
+ * the interrupt.
+ */
+ ath9k_hw_procmibevent(ah, &sc->sc_halstats);
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+ }
+ if (status & ATH9K_INT_TIM_TIMER) {
+ if (!(ah->ah_caps.hw_caps &
+ ATH9K_HW_CAP_AUTOSLEEP)) {
+ /* Clear RxAbort bit so that we can
+ * receive frames */
+ ath9k_hw_setrxabort(ah, 0);
+ sched = true;
+ }
+ }
+ }
+ } while (0);
+
+ if (sched) {
+ /* turn off every interrupt except SWBA */
+ ath9k_hw_set_interrupts(ah, (sc->sc_imask & ATH9K_INT_SWBA));
+ tasklet_schedule(&sc->intr_tq);
+ }
+
+ return IRQ_HANDLED;
+}
+
static int ath_get_channel(struct ath_softc *sc,
struct ieee80211_channel *chan)
{
@@ -90,6 +662,23 @@
return chanmode;
}
+static void ath_key_reset(struct ath_softc *sc, u16 keyix, int freeslot)
+{
+ ath9k_hw_keyreset(sc->sc_ah, keyix);
+ if (freeslot)
+ clear_bit(keyix, sc->sc_keymap);
+}
+
+static int ath_keyset(struct ath_softc *sc, u16 keyix,
+ struct ath9k_keyval *hk, const u8 mac[ETH_ALEN])
+{
+ bool status;
+
+ status = ath9k_hw_set_keycache_entry(sc->sc_ah,
+ keyix, hk, mac, false);
+
+ return status != false;
+}
static int ath_setkey_tkip(struct ath_softc *sc,
struct ieee80211_key_conf *key,
@@ -327,20 +916,6 @@
}
}
-void ath_get_beaconconfig(struct ath_softc *sc,
- int if_id,
- struct ath_beacon_config *conf)
-{
- struct ieee80211_hw *hw = sc->hw;
-
- /* fill in beacon config data */
-
- conf->beacon_interval = hw->conf.beacon_int;
- conf->listen_interval = 100;
- conf->dtim_count = 1;
- conf->bmiss_timeout = ATH_DEFAULT_BMISS_LIMIT * conf->listen_interval;
-}
-
/********************************/
/* LED functions */
/********************************/
@@ -722,6 +1297,244 @@
ath9k_hw_detach(sc->sc_ah);
}
+static int ath_init(u16 devid, struct ath_softc *sc)
+{
+ struct ath_hal *ah = NULL;
+ int status;
+ int error = 0, i;
+ int csz = 0;
+
+ /* XXX: hardware will not be ready until ath_open() being called */
+ sc->sc_flags |= SC_OP_INVALID;
+ sc->sc_debug = DBG_DEFAULT;
+
+ spin_lock_init(&sc->sc_resetlock);
+ tasklet_init(&sc->intr_tq, ath9k_tasklet, (unsigned long)sc);
+ tasklet_init(&sc->bcon_tasklet, ath9k_beacon_tasklet,
+ (unsigned long)sc);
+
+ /*
+ * Cache line size is used to size and align various
+ * structures used to communicate with the hardware.
+ */
+ bus_read_cachesize(sc, &csz);
+ /* XXX assert csz is non-zero */
+ sc->sc_cachelsz = csz << 2; /* convert to bytes */
+
+ ah = ath9k_hw_attach(devid, sc, sc->mem, &status);
+ if (ah == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to attach hardware; HAL status %u\n",
+ __func__, status);
+ error = -ENXIO;
+ goto bad;
+ }
+ sc->sc_ah = ah;
+
+ /* Get the hardware key cache size. */
+ sc->sc_keymax = ah->ah_caps.keycache_size;
+ if (sc->sc_keymax > ATH_KEYMAX) {
+ DPRINTF(sc, ATH_DBG_KEYCACHE,
+ "%s: Warning, using only %u entries in %u key cache\n",
+ __func__, ATH_KEYMAX, sc->sc_keymax);
+ sc->sc_keymax = ATH_KEYMAX;
+ }
+
+ /*
+ * Reset the key cache since some parts do not
+ * reset the contents on initial power up.
+ */
+ for (i = 0; i < sc->sc_keymax; i++)
+ ath9k_hw_keyreset(ah, (u16) i);
+ /*
+ * Mark key cache slots associated with global keys
+ * as in use. If we knew TKIP was not to be used we
+ * could leave the +32, +64, and +32+64 slots free.
+ * XXX only for splitmic.
+ */
+ for (i = 0; i < IEEE80211_WEP_NKID; i++) {
+ set_bit(i, sc->sc_keymap);
+ set_bit(i + 32, sc->sc_keymap);
+ set_bit(i + 64, sc->sc_keymap);
+ set_bit(i + 32 + 64, sc->sc_keymap);
+ }
+
+ /* Collect the channel list using the default country code */
+
+ error = ath_setup_channels(sc);
+ if (error)
+ goto bad;
+
+ /* default to MONITOR mode */
+ sc->sc_ah->ah_opmode = ATH9K_M_MONITOR;
+
+ /* Setup rate tables */
+
+ ath_rate_attach(sc);
+ ath_setup_rates(sc, IEEE80211_BAND_2GHZ);
+ ath_setup_rates(sc, IEEE80211_BAND_5GHZ);
+
+ /*
+ * Allocate hardware transmit queues: one queue for
+ * beacon frames and one data queue for each QoS
+ * priority. Note that the hal handles reseting
+ * these queues at the needed time.
+ */
+ sc->sc_bhalq = ath_beaconq_setup(ah);
+ if (sc->sc_bhalq == -1) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup a beacon xmit queue\n", __func__);
+ error = -EIO;
+ goto bad2;
+ }
+ sc->sc_cabq = ath_txq_setup(sc, ATH9K_TX_QUEUE_CAB, 0);
+ if (sc->sc_cabq == NULL) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup CAB xmit queue\n", __func__);
+ error = -EIO;
+ goto bad2;
+ }
+
+ sc->sc_config.cabqReadytime = ATH_CABQ_READY_TIME;
+ ath_cabq_update(sc);
+
+ for (i = 0; i < ARRAY_SIZE(sc->sc_haltype2q); i++)
+ sc->sc_haltype2q[i] = -1;
+
+ /* Setup data queues */
+ /* NB: ensure BK queue is the lowest priority h/w queue */
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_BK)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for BK traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_BE)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for BE traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_VI)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for VI traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+ if (!ath_tx_setup(sc, ATH9K_WME_AC_VO)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to setup xmit queue for VO traffic\n",
+ __func__);
+ error = -EIO;
+ goto bad2;
+ }
+
+ /* Initializes the noise floor to a reasonable default value.
+ * Later on this will be updated during ANI processing. */
+
+ sc->sc_ani.sc_noise_floor = ATH_DEFAULT_NOISE_FLOOR;
+ setup_timer(&sc->sc_ani.timer, ath_ani_calibrate, (unsigned long)sc);
+
+ if (ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER,
+ ATH9K_CIPHER_TKIP, NULL)) {
+ /*
+ * Whether we should enable h/w TKIP MIC.
+ * XXX: if we don't support WME TKIP MIC, then we wouldn't
+ * report WMM capable, so it's always safe to turn on
+ * TKIP MIC in this case.
+ */
+ ath9k_hw_setcapability(sc->sc_ah, ATH9K_CAP_TKIP_MIC,
+ 0, 1, NULL);
+ }
+
+ /*
+ * Check whether the separate key cache entries
+ * are required to handle both tx+rx MIC keys.
+ * With split mic keys the number of stations is limited
+ * to 27 otherwise 59.
+ */
+ if (ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER,
+ ATH9K_CIPHER_TKIP, NULL)
+ && ath9k_hw_getcapability(ah, ATH9K_CAP_CIPHER,
+ ATH9K_CIPHER_MIC, NULL)
+ && ath9k_hw_getcapability(ah, ATH9K_CAP_TKIP_SPLIT,
+ 0, NULL))
+ sc->sc_splitmic = 1;
+
+ /* turn on mcast key search if possible */
+ if (!ath9k_hw_getcapability(ah, ATH9K_CAP_MCAST_KEYSRCH, 0, NULL))
+ (void)ath9k_hw_setcapability(ah, ATH9K_CAP_MCAST_KEYSRCH, 1,
+ 1, NULL);
+
+ sc->sc_config.txpowlimit = ATH_TXPOWER_MAX;
+ sc->sc_config.txpowlimit_override = 0;
+
+ /* 11n Capabilities */
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT) {
+ sc->sc_flags |= SC_OP_TXAGGR;
+ sc->sc_flags |= SC_OP_RXAGGR;
+ }
+
+ sc->sc_tx_chainmask = ah->ah_caps.tx_chainmask;
+ sc->sc_rx_chainmask = ah->ah_caps.rx_chainmask;
+
+ ath9k_hw_setcapability(ah, ATH9K_CAP_DIVERSITY, 1, true, NULL);
+ sc->sc_defant = ath9k_hw_getdefantenna(ah);
+
+ ath9k_hw_getmac(ah, sc->sc_myaddr);
+ if (ah->ah_caps.hw_caps & ATH9K_HW_CAP_BSSIDMASK) {
+ ath9k_hw_getbssidmask(ah, sc->sc_bssidmask);
+ ATH_SET_VAP_BSSID_MASK(sc->sc_bssidmask);
+ ath9k_hw_setbssidmask(ah, sc->sc_bssidmask);
+ }
+
+ sc->sc_slottime = ATH9K_SLOT_TIME_9; /* default to short slot time */
+
+ /* initialize beacon slots */
+ for (i = 0; i < ARRAY_SIZE(sc->sc_bslot); i++)
+ sc->sc_bslot[i] = ATH_IF_ID_ANY;
+
+ /* save MISC configurations */
+ sc->sc_config.swBeaconProcess = 1;
+
+#ifdef CONFIG_SLOW_ANT_DIV
+ /* range is 40 - 255, we use something in the middle */
+ ath_slow_ant_div_init(&sc->sc_antdiv, sc, 0x127);
+#endif
+
+ /* setup channels and rates */
+
+ sc->sbands[IEEE80211_BAND_2GHZ].channels =
+ sc->channels[IEEE80211_BAND_2GHZ];
+ sc->sbands[IEEE80211_BAND_2GHZ].bitrates =
+ sc->rates[IEEE80211_BAND_2GHZ];
+ sc->sbands[IEEE80211_BAND_2GHZ].band = IEEE80211_BAND_2GHZ;
+
+ if (test_bit(ATH9K_MODE_11A, sc->sc_ah->ah_caps.wireless_modes)) {
+ sc->sbands[IEEE80211_BAND_5GHZ].channels =
+ sc->channels[IEEE80211_BAND_5GHZ];
+ sc->sbands[IEEE80211_BAND_5GHZ].bitrates =
+ sc->rates[IEEE80211_BAND_5GHZ];
+ sc->sbands[IEEE80211_BAND_5GHZ].band = IEEE80211_BAND_5GHZ;
+ }
+
+ return 0;
+bad2:
+ /* cleanup tx queues */
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++)
+ if (ATH_TXQ_SETUP(sc, i))
+ ath_tx_cleanupq(sc, &sc->sc_txq[i]);
+bad:
+ if (ah)
+ ath9k_hw_detach(ah);
+
+ return error;
+}
+
static int ath_attach(u16 devid, struct ath_softc *sc)
{
struct ieee80211_hw *hw = sc->hw;
@@ -810,11 +1623,243 @@
return error;
}
+int ath_reset(struct ath_softc *sc, bool retry_tx)
+{
+ struct ath_hal *ah = sc->sc_ah;
+ int status;
+ int error = 0;
+
+ ath9k_hw_set_interrupts(ah, 0);
+ ath_draintxq(sc, retry_tx);
+ ath_stoprecv(sc);
+ ath_flushrecv(sc);
+
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(ah, sc->sc_ah->ah_curchan,
+ sc->sc_ht_info.tx_chan_width,
+ sc->sc_tx_chainmask, sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing, false, &status)) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to reset hardware; hal status %u\n",
+ __func__, status);
+ error = -EIO;
+ }
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ if (ath_startrecv(sc) != 0)
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to start recv logic\n", __func__);
+
+ /*
+ * We may be doing a reset in response to a request
+ * that changes the channel so update any state that
+ * might change as a result.
+ */
+ ath_setcurmode(sc, ath_chan2mode(sc->sc_ah->ah_curchan));
+
+ ath_update_txpow(sc);
+
+ if (sc->sc_flags & SC_OP_BEACONS)
+ ath_beacon_config(sc, ATH_IF_ID_ANY); /* restart beacons */
+
+ ath9k_hw_set_interrupts(ah, sc->sc_imask);
+
+ if (retry_tx) {
+ int i;
+ for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) {
+ if (ATH_TXQ_SETUP(sc, i)) {
+ spin_lock_bh(&sc->sc_txq[i].axq_lock);
+ ath_txq_schedule(sc, &sc->sc_txq[i]);
+ spin_unlock_bh(&sc->sc_txq[i].axq_lock);
+ }
+ }
+ }
+
+ return error;
+}
+
+/*
+ * This function will allocate both the DMA descriptor structure, and the
+ * buffers it contains. These are used to contain the descriptors used
+ * by the system.
+*/
+int ath_descdma_setup(struct ath_softc *sc, struct ath_descdma *dd,
+ struct list_head *head, const char *name,
+ int nbuf, int ndesc)
+{
+#define DS2PHYS(_dd, _ds) \
+ ((_dd)->dd_desc_paddr + ((caddr_t)(_ds) - (caddr_t)(_dd)->dd_desc))
+#define ATH_DESC_4KB_BOUND_CHECK(_daddr) ((((_daddr) & 0xFFF) > 0xF7F) ? 1 : 0)
+#define ATH_DESC_4KB_BOUND_NUM_SKIPPED(_len) ((_len) / 4096)
+
+ struct ath_desc *ds;
+ struct ath_buf *bf;
+ int i, bsize, error;
+
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: %s DMA: %u buffers %u desc/buf\n",
+ __func__, name, nbuf, ndesc);
+
+ /* ath_desc must be a multiple of DWORDs */
+ if ((sizeof(struct ath_desc) % 4) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL, "%s: ath_desc not DWORD aligned\n",
+ __func__);
+ ASSERT((sizeof(struct ath_desc) % 4) == 0);
+ error = -ENOMEM;
+ goto fail;
+ }
+
+ dd->dd_name = name;
+ dd->dd_desc_len = sizeof(struct ath_desc) * nbuf * ndesc;
+
+ /*
+ * Need additional DMA memory because we can't use
+ * descriptors that cross the 4K page boundary. Assume
+ * one skipped descriptor per 4K page.
+ */
+ if (!(sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_4KB_SPLITTRANS)) {
+ u32 ndesc_skipped =
+ ATH_DESC_4KB_BOUND_NUM_SKIPPED(dd->dd_desc_len);
+ u32 dma_len;
+
+ while (ndesc_skipped) {
+ dma_len = ndesc_skipped * sizeof(struct ath_desc);
+ dd->dd_desc_len += dma_len;
+
+ ndesc_skipped = ATH_DESC_4KB_BOUND_NUM_SKIPPED(dma_len);
+ };
+ }
+
+ /* allocate descriptors */
+ dd->dd_desc = pci_alloc_consistent(sc->pdev,
+ dd->dd_desc_len,
+ &dd->dd_desc_paddr);
+ if (dd->dd_desc == NULL) {
+ error = -ENOMEM;
+ goto fail;
+ }
+ ds = dd->dd_desc;
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: %s DMA map: %p (%u) -> %llx (%u)\n",
+ __func__, dd->dd_name, ds, (u32) dd->dd_desc_len,
+ ito64(dd->dd_desc_paddr), /*XXX*/(u32) dd->dd_desc_len);
+
+ /* allocate buffers */
+ bsize = sizeof(struct ath_buf) * nbuf;
+ bf = kmalloc(bsize, GFP_KERNEL);
+ if (bf == NULL) {
+ error = -ENOMEM;
+ goto fail2;
+ }
+ memset(bf, 0, bsize);
+ dd->dd_bufptr = bf;
+
+ INIT_LIST_HEAD(head);
+ for (i = 0; i < nbuf; i++, bf++, ds += ndesc) {
+ bf->bf_desc = ds;
+ bf->bf_daddr = DS2PHYS(dd, ds);
+
+ if (!(sc->sc_ah->ah_caps.hw_caps &
+ ATH9K_HW_CAP_4KB_SPLITTRANS)) {
+ /*
+ * Skip descriptor addresses which can cause 4KB
+ * boundary crossing (addr + length) with a 32 dword
+ * descriptor fetch.
+ */
+ while (ATH_DESC_4KB_BOUND_CHECK(bf->bf_daddr)) {
+ ASSERT((caddr_t) bf->bf_desc <
+ ((caddr_t) dd->dd_desc +
+ dd->dd_desc_len));
+
+ ds += ndesc;
+ bf->bf_desc = ds;
+ bf->bf_daddr = DS2PHYS(dd, ds);
+ }
+ }
+ list_add_tail(&bf->list, head);
+ }
+ return 0;
+fail2:
+ pci_free_consistent(sc->pdev,
+ dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr);
+fail:
+ memset(dd, 0, sizeof(*dd));
+ return error;
+#undef ATH_DESC_4KB_BOUND_CHECK
+#undef ATH_DESC_4KB_BOUND_NUM_SKIPPED
+#undef DS2PHYS
+}
+
+void ath_descdma_cleanup(struct ath_softc *sc,
+ struct ath_descdma *dd,
+ struct list_head *head)
+{
+ pci_free_consistent(sc->pdev,
+ dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr);
+
+ INIT_LIST_HEAD(head);
+ kfree(dd->dd_bufptr);
+ memset(dd, 0, sizeof(*dd));
+}
+
+int ath_get_hal_qnum(u16 queue, struct ath_softc *sc)
+{
+ int qnum;
+
+ switch (queue) {
+ case 0:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_VO];
+ break;
+ case 1:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_VI];
+ break;
+ case 2:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_BE];
+ break;
+ case 3:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_BK];
+ break;
+ default:
+ qnum = sc->sc_haltype2q[ATH9K_WME_AC_BE];
+ break;
+ }
+
+ return qnum;
+}
+
+int ath_get_mac80211_qnum(u32 queue, struct ath_softc *sc)
+{
+ int qnum;
+
+ switch (queue) {
+ case ATH9K_WME_AC_VO:
+ qnum = 0;
+ break;
+ case ATH9K_WME_AC_VI:
+ qnum = 1;
+ break;
+ case ATH9K_WME_AC_BE:
+ qnum = 2;
+ break;
+ case ATH9K_WME_AC_BK:
+ qnum = 3;
+ break;
+ default:
+ qnum = -1;
+ break;
+ }
+
+ return qnum;
+}
+
+/**********************/
+/* mac80211 callbacks */
+/**********************/
+
static int ath9k_start(struct ieee80211_hw *hw)
{
struct ath_softc *sc = hw->priv;
struct ieee80211_channel *curchan = hw->conf.channel;
- int error = 0, pos;
+ struct ath9k_channel *init_channel;
+ int error = 0, pos, status;
DPRINTF(sc, ATH_DBG_CONFIG, "%s: Starting driver with "
"initial channel: %d MHz\n", __func__, curchan->center_freq);
@@ -827,24 +1872,103 @@
if (pos == -1) {
DPRINTF(sc, ATH_DBG_FATAL, "%s: Invalid channel\n", __func__);
error = -EINVAL;
- goto exit;
+ goto error;
}
sc->sc_ah->ah_channels[pos].chanmode =
(curchan->band == IEEE80211_BAND_2GHZ) ? CHANNEL_G : CHANNEL_A;
+ init_channel = &sc->sc_ah->ah_channels[pos];
- error = ath_open(sc, &sc->sc_ah->ah_channels[pos]);
- if (error) {
+ /* Reset SERDES registers */
+ ath9k_hw_configpcipowersave(sc->sc_ah, 0);
+
+ /*
+ * The basic interface to setting the hardware in a good
+ * state is ``reset''. On return the hardware is known to
+ * be powered up and with interrupts disabled. This must
+ * be followed by initialization of the appropriate bits
+ * and then setup of the interrupt mask.
+ */
+ spin_lock_bh(&sc->sc_resetlock);
+ if (!ath9k_hw_reset(sc->sc_ah, init_channel,
+ sc->sc_ht_info.tx_chan_width,
+ sc->sc_tx_chainmask, sc->sc_rx_chainmask,
+ sc->sc_ht_extprotspacing, false, &status)) {
DPRINTF(sc, ATH_DBG_FATAL,
- "%s: Unable to complete ath_open\n", __func__);
- goto exit;
+ "%s: unable to reset hardware; hal status %u "
+ "(freq %u flags 0x%x)\n", __func__, status,
+ init_channel->channel, init_channel->channelFlags);
+ error = -EIO;
+ spin_unlock_bh(&sc->sc_resetlock);
+ goto error;
}
+ spin_unlock_bh(&sc->sc_resetlock);
+
+ /*
+ * This is needed only to setup initial state
+ * but it's best done after a reset.
+ */
+ ath_update_txpow(sc);
+
+ /*
+ * Setup the hardware after reset:
+ * The receive engine is set going.
+ * Frame transmit is handled entirely
+ * in the frame output path; there's nothing to do
+ * here except setup the interrupt mask.
+ */
+ if (ath_startrecv(sc) != 0) {
+ DPRINTF(sc, ATH_DBG_FATAL,
+ "%s: unable to start recv logic\n", __func__);
+ error = -EIO;
+ goto error;
+ }
+
+ /* Setup our intr mask. */
+ sc->sc_imask = ATH9K_INT_RX | ATH9K_INT_TX
+ | ATH9K_INT_RXEOL | ATH9K_INT_RXORN
+ | ATH9K_INT_FATAL | ATH9K_INT_GLOBAL;
+
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_GTT)
+ sc->sc_imask |= ATH9K_INT_GTT;
+
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_HT)
+ sc->sc_imask |= ATH9K_INT_CST;
+
+ /*
+ * Enable MIB interrupts when there are hardware phy counters.
+ * Note we only do this (at the moment) for station mode.
+ */
+ if (ath9k_hw_phycounters(sc->sc_ah) &&
+ ((sc->sc_ah->ah_opmode == ATH9K_M_STA) ||
+ (sc->sc_ah->ah_opmode == ATH9K_M_IBSS)))
+ sc->sc_imask |= ATH9K_INT_MIB;
+ /*
+ * Some hardware processes the TIM IE and fires an
+ * interrupt when the TIM bit is set. For hardware
+ * that does, if not overridden by configuration,
+ * enable the TIM interrupt when operating as station.
+ */
+ if ((sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_ENHANCEDPM) &&
+ (sc->sc_ah->ah_opmode == ATH9K_M_STA) &&
+ !sc->sc_config.swBeaconProcess)
+ sc->sc_imask |= ATH9K_INT_TIM;
+
+ ath_setcurmode(sc, ath_chan2mode(init_channel));
+
+ sc->sc_flags &= ~SC_OP_INVALID;
+
+ /* Disable BMISS interrupt when we're not associated */
+ sc->sc_imask &= ~(ATH9K_INT_SWBA | ATH9K_INT_BMISS);
+ ath9k_hw_set_interrupts(sc->sc_ah, sc->sc_imask);
+
+ ieee80211_wake_queues(sc->hw);
#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
error = ath_start_rfkill_poll(sc);
#endif
-exit:
+error:
return error;
}
@@ -911,7 +2035,30 @@
return;
}
- ath_stop(sc);
+ DPRINTF(sc, ATH_DBG_CONFIG, "%s: Cleaning up\n", __func__);
+
+ ieee80211_stop_queues(sc->hw);
+
+ /* make sure h/w will not generate any interrupt
+ * before setting the invalid flag. */
+ ath9k_hw_set_interrupts(sc->sc_ah, 0);
+
+ if (!(sc->sc_flags & SC_OP_INVALID)) {
+ ath_draintxq(sc, false);
+ ath_stoprecv(sc);
+ ath9k_hw_phy_disable(sc->sc_ah);
+ } else
+ sc->sc_rxlink = NULL;
+
+#if defined(CONFIG_RFKILL) || defined(CONFIG_RFKILL_MODULE)
+ if (sc->sc_ah->ah_caps.hw_caps & ATH9K_HW_CAP_RFSILENT)
+ cancel_delayed_work_sync(&sc->rf_kill.rfkill_poll);
+#endif
+ /* disable HAL and put h/w to sleep */
+ ath9k_hw_disable(sc->sc_ah);
+ ath9k_hw_configpcipowersave(sc->sc_ah, 1);
+
+ sc->sc_flags |= SC_OP_INVALID;
DPRINTF(sc, ATH_DBG_CONFIG, "%s: Driver halt\n", __func__);
}