Blackfin: bf548-ezkit/bf537-stamp: add resources for ADXL345/346
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/arch/blackfin/mach-bf548/boards/ezkit.c b/arch/blackfin/mach-bf548/boards/ezkit.c
index 2780e41..add5a17 100644
--- a/arch/blackfin/mach-bf548/boards/ezkit.c
+++ b/arch/blackfin/mach-bf548/boards/ezkit.c
@@ -208,6 +208,43 @@
};
#endif
+#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#include <linux/input.h>
+#include <linux/spi/adxl34x.h>
+static const struct adxl34x_platform_data adxl34x_info = {
+ .x_axis_offset = 0,
+ .y_axis_offset = 0,
+ .z_axis_offset = 0,
+ .tap_threshold = 0x31,
+ .tap_duration = 0x10,
+ .tap_latency = 0x60,
+ .tap_window = 0xF0,
+ .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
+ .act_axis_control = 0xFF,
+ .activity_threshold = 5,
+ .inactivity_threshold = 3,
+ .inactivity_time = 4,
+ .free_fall_threshold = 0x7,
+ .free_fall_time = 0x20,
+ .data_rate = 0x8,
+ .data_range = ADXL_FULL_RES,
+
+ .ev_type = EV_ABS,
+ .ev_code_x = ABS_X, /* EV_REL */
+ .ev_code_y = ABS_Y, /* EV_REL */
+ .ev_code_z = ABS_Z, /* EV_REL */
+
+ .ev_code_tap_x = BTN_TOUCH, /* EV_KEY */
+ .ev_code_tap_y = BTN_TOUCH, /* EV_KEY */
+ .ev_code_tap_z = BTN_TOUCH, /* EV_KEY */
+
+/* .ev_code_ff = KEY_F,*/ /* EV_KEY */
+/* .ev_code_act_inactivity = KEY_A,*/ /* EV_KEY */
+ .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
+ .fifo_mode = ADXL_FIFO_STREAM,
+};
+#endif
+
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
@@ -628,6 +665,14 @@
};
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+ .cs_change_per_word = 0,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
@@ -653,15 +698,15 @@
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-{
- .modalias = "ad7877",
- .platform_data = &bfin_ad7877_ts_info,
- .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 2,
- .controller_data = &spi_ad7877_chip_info,
-},
+ {
+ .modalias = "ad7877",
+ .platform_data = &bfin_ad7877_ts_info,
+ .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2,
+ .controller_data = &spi_ad7877_chip_info,
+ },
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
{
@@ -672,8 +717,19 @@
.controller_data = &spidev_chip_info,
},
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+ {
+ .modalias = "adxl34x",
+ .platform_data = &adxl34x_info,
+ .irq = IRQ_PC5,
+ .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = 2,
+ .controller_data = &spi_adxl34x_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
};
-
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
@@ -797,6 +853,13 @@
.irq = 212,
},
#endif
+#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("adxl34x", 0x53),
+ .irq = IRQ_PC5,
+ .platform_data = (void *)&adxl34x_info,
+ },
+#endif
};
#endif