blob: de8427be830a32e24a01ace97f11303435528b7b [file] [log] [blame]
Tony Lindgren78000642015-01-19 11:47:35 -08001/*
2 * This file is licensed under the terms of the GNU General Public License
3 * version 2. This program is licensed "as is" without any warranty of any
4 * kind, whether express or implied.
5 */
6
7#include <dt-bindings/gpio/gpio.h>
8#include <dt-bindings/pinctrl/omap.h>
9
10#include "skeleton.dtsi"
11
12/ {
13 compatible = "ti,dm816";
14 interrupt-parent = <&intc>;
15
16 aliases {
17 i2c0 = &i2c1;
18 i2c1 = &i2c2;
19 serial0 = &uart1;
20 serial1 = &uart2;
21 serial2 = &uart3;
22 ethernet0 = &eth0;
23 ethernet1 = &eth1;
24 };
25
26 cpus {
27 #address-cells = <1>;
28 #size-cells = <0>;
29 cpu@0 {
30 compatible = "arm,cortex-a8";
31 device_type = "cpu";
32 reg = <0>;
33 };
34 };
35
36 pmu {
37 compatible = "arm,cortex-a8-pmu";
38 interrupts = <3>;
39 };
40
41 /*
42 * The soc node represents the soc top level view. It is used for IPs
43 * that are not memory mapped in the MPU view or for the MPU itself.
44 */
45 soc {
46 compatible = "ti,omap-infra";
47 mpu {
48 compatible = "ti,omap3-mpu";
49 ti,hwmods = "mpu";
50 };
51 };
52
Tony Lindgren78000642015-01-19 11:47:35 -080053 /*
54 * XXX: Use a flat representation of the dm816x interconnect.
55 * The real dm816x interconnect network is quite complex. Since
56 * it will not bring real advantage to represent that in DT
57 * for the moment, just use a fake OCP bus entry to represent
58 * the whole bus hierarchy.
59 */
60 ocp {
61 compatible = "ti,omap3-l3-smx", "simple-bus";
62 reg = <0x44000000 0x10000>;
63 interrupts = <9 10>;
64 #address-cells = <1>;
65 #size-cells = <1>;
66 ranges;
67 ti,hwmods = "l3_main";
68
69 prcm: prcm@48180000 {
70 compatible = "ti,dm816-prcm";
71 reg = <0x48180000 0x4000>;
72
73 prcm_clocks: clocks {
74 #address-cells = <1>;
75 #size-cells = <0>;
76 };
77
78 prcm_clockdomains: clockdomains {
79 };
80 };
81
82 scrm: scrm@48140000 {
Tony Lindgren72d03222015-01-21 16:21:52 -080083 compatible = "ti,dm816-scrm", "simple-bus";
Tony Lindgren78000642015-01-19 11:47:35 -080084 reg = <0x48140000 0x21000>;
85 #address-cells = <1>;
86 #size-cells = <1>;
87 ranges = <0 0x48140000 0x21000>;
88
Tony Lindgren72d03222015-01-21 16:21:52 -080089 dm816x_pinmux: pinmux@800 {
90 compatible = "pinctrl-single";
91 reg = <0x800 0x50a>;
92 #address-cells = <1>;
93 #size-cells = <0>;
94 pinctrl-single,register-width = <16>;
95 pinctrl-single,function-mask = <0xf>;
96 };
97
98 /* Device Configuration Registers */
99 scm_conf: syscon@600 {
Tony Lindgrena54879a2015-02-24 08:48:52 -0800100 compatible = "syscon", "simple-bus";
Tony Lindgren72d03222015-01-21 16:21:52 -0800101 reg = <0x600 0x110>;
102 #address-cells = <1>;
103 #size-cells = <1>;
Tony Lindgrena54879a2015-02-24 08:48:52 -0800104 ranges = <0 0x600 0x110>;
105
106 usb_phy0: usb-phy@20 {
107 compatible = "ti,dm8168-usb-phy";
108 reg = <0x20 0x8>;
109 reg-names = "phy";
110 clocks = <&main_fapll 6>;
111 clock-names = "refclk";
112 #phy-cells = <0>;
113 syscon = <&scm_conf>;
114 };
115
116 usb_phy1: usb-phy@28 {
117 compatible = "ti,dm8168-usb-phy";
118 reg = <0x28 0x8>;
119 reg-names = "phy";
120 clocks = <&main_fapll 6>;
121 clock-names = "refclk";
122 #phy-cells = <0>;
123 syscon = <&scm_conf>;
124 };
Tony Lindgren72d03222015-01-21 16:21:52 -0800125 };
126
Tony Lindgren78000642015-01-19 11:47:35 -0800127 scrm_clocks: clocks {
128 #address-cells = <1>;
129 #size-cells = <0>;
130 };
131
132 scrm_clockdomains: clockdomains {
133 };
134 };
135
Tony Lindgren78000642015-01-19 11:47:35 -0800136 edma: edma@49000000 {
137 compatible = "ti,edma3";
138 ti,hwmods = "tpcc", "tptc0", "tptc1", "tptc2", "tptc3";
139 reg = <0x49000000 0x10000>,
140 <0x44e10f90 0x40>;
141 interrupts = <12 13 14>;
142 #dma-cells = <1>;
143 };
144
145 elm: elm@48080000 {
146 compatible = "ti,816-elm";
147 ti,hwmods = "elm";
148 reg = <0x48080000 0x2000>;
149 interrupts = <4>;
150 };
151
152 gpio1: gpio@48032000 {
Tony Lindgren599c3762015-03-18 13:41:34 -0700153 compatible = "ti,omap4-gpio";
Tony Lindgren78000642015-01-19 11:47:35 -0800154 ti,hwmods = "gpio1";
Tony Lindgren599c3762015-03-18 13:41:34 -0700155 ti,gpio-always-on;
Tony Lindgren78000642015-01-19 11:47:35 -0800156 reg = <0x48032000 0x1000>;
Tony Lindgren599c3762015-03-18 13:41:34 -0700157 interrupts = <96>;
158 gpio-controller;
159 #gpio-cells = <2>;
160 interrupt-controller;
161 #interrupt-cells = <2>;
Tony Lindgren78000642015-01-19 11:47:35 -0800162 };
163
164 gpio2: gpio@4804c000 {
Tony Lindgren599c3762015-03-18 13:41:34 -0700165 compatible = "ti,omap4-gpio";
Tony Lindgren78000642015-01-19 11:47:35 -0800166 ti,hwmods = "gpio2";
Tony Lindgren599c3762015-03-18 13:41:34 -0700167 ti,gpio-always-on;
Tony Lindgren78000642015-01-19 11:47:35 -0800168 reg = <0x4804c000 0x1000>;
Tony Lindgren599c3762015-03-18 13:41:34 -0700169 interrupts = <98>;
170 gpio-controller;
171 #gpio-cells = <2>;
172 interrupt-controller;
173 #interrupt-cells = <2>;
Tony Lindgren78000642015-01-19 11:47:35 -0800174 };
175
176 gpmc: gpmc@50000000 {
177 compatible = "ti,am3352-gpmc";
178 ti,hwmods = "gpmc";
179 reg = <0x50000000 0x2000>;
180 #address-cells = <2>;
181 #size-cells = <1>;
182 interrupts = <100>;
183 gpmc,num-cs = <6>;
184 gpmc,num-waitpins = <2>;
185 };
186
187 i2c1: i2c@48028000 {
188 compatible = "ti,omap4-i2c";
189 ti,hwmods = "i2c1";
190 reg = <0x48028000 0x1000>;
191 #address-cells = <1>;
192 #size-cells = <0>;
193 interrupts = <70>;
194 dmas = <&edma 58 &edma 59>;
195 dma-names = "tx", "rx";
196 };
197
198 i2c2: i2c@4802a000 {
199 compatible = "ti,omap4-i2c";
200 ti,hwmods = "i2c2";
201 reg = <0x4802a000 0x1000>;
202 #address-cells = <1>;
203 #size-cells = <0>;
204 interrupts = <71>;
205 dmas = <&edma 60 &edma 61>;
206 dma-names = "tx", "rx";
207 };
208
209 intc: interrupt-controller@48200000 {
210 compatible = "ti,dm816-intc";
211 interrupt-controller;
212 #interrupt-cells = <1>;
213 reg = <0x48200000 0x1000>;
214 };
215
216 mailbox: mailbox@480c8000 {
217 compatible = "ti,omap4-mailbox";
218 reg = <0x480c8000 0x2000>;
219 interrupts = <77>;
220 ti,hwmods = "mailbox";
221 ti,mbox-num-users = <4>;
222 ti,mbox-num-fifos = <12>;
223 mbox_dsp: mbox_dsp {
224 ti,mbox-tx = <3 0 0>;
225 ti,mbox-rx = <0 0 0>;
226 };
227 };
228
229 mdio: mdio@4a100800 {
230 compatible = "ti,davinci_mdio";
231 #address-cells = <1>;
232 #size-cells = <0>;
233 reg = <0x4a100800 0x100>;
234 ti,hwmods = "davinci_mdio";
235 bus_freq = <1000000>;
236 phy0: ethernet-phy@0 {
237 reg = <1>;
238 };
239 phy1: ethernet-phy@1 {
240 reg = <2>;
241 };
242 };
243
244 eth0: ethernet@4a100000 {
245 compatible = "ti,dm816-emac";
246 ti,hwmods = "emac0";
247 reg = <0x4a100000 0x800
248 0x4a100900 0x3700>;
249 clocks = <&sysclk24_ck>;
Tony Lindgren72d03222015-01-21 16:21:52 -0800250 syscon = <&scm_conf>;
Tony Lindgren78000642015-01-19 11:47:35 -0800251 ti,davinci-ctrl-reg-offset = <0>;
252 ti,davinci-ctrl-mod-reg-offset = <0x900>;
253 ti,davinci-ctrl-ram-offset = <0x2000>;
254 ti,davinci-ctrl-ram-size = <0x2000>;
255 interrupts = <40 41 42 43>;
256 phy-handle = <&phy0>;
257 };
258
259 eth1: ethernet@4a120000 {
260 compatible = "ti,dm816-emac";
261 ti,hwmods = "emac1";
262 reg = <0x4a120000 0x4000>;
263 clocks = <&sysclk24_ck>;
Tony Lindgren72d03222015-01-21 16:21:52 -0800264 syscon = <&scm_conf>;
Tony Lindgren78000642015-01-19 11:47:35 -0800265 ti,davinci-ctrl-reg-offset = <0>;
266 ti,davinci-ctrl-mod-reg-offset = <0x900>;
267 ti,davinci-ctrl-ram-offset = <0x2000>;
268 ti,davinci-ctrl-ram-size = <0x2000>;
269 interrupts = <44 45 46 47>;
270 phy-handle = <&phy1>;
271 };
272
273 mcspi1: spi@48030000 {
274 compatible = "ti,omap4-mcspi";
275 reg = <0x48030000 0x1000>;
276 #address-cells = <1>;
277 #size-cells = <0>;
278 interrupts = <65>;
279 ti,spi-num-cs = <4>;
280 ti,hwmods = "mcspi1";
281 dmas = <&edma 16 &edma 17
282 &edma 18 &edma 19>;
283 dma-names = "tx0", "rx0", "tx1", "rx1";
284 };
285
286 mmc1: mmc@48060000 {
287 compatible = "ti,omap4-hsmmc";
288 reg = <0x48060000 0x11000>;
289 ti,hwmods = "mmc1";
290 interrupts = <64>;
291 dmas = <&edma 24 &edma 25>;
292 dma-names = "tx", "rx";
293 };
294
295 timer1: timer@4802e000 {
296 compatible = "ti,dm816-timer";
297 reg = <0x4802e000 0x2000>;
298 interrupts = <67>;
299 ti,hwmods = "timer1";
300 ti,timer-alwon;
301 };
302
303 timer2: timer@48040000 {
304 compatible = "ti,dm816-timer";
305 reg = <0x48040000 0x2000>;
306 interrupts = <68>;
307 ti,hwmods = "timer2";
308 };
309
310 timer3: timer@48042000 {
311 compatible = "ti,dm816-timer";
312 reg = <0x48042000 0x2000>;
313 interrupts = <69>;
314 ti,hwmods = "timer3";
315 };
316
317 timer4: timer@48044000 {
318 compatible = "ti,dm816-timer";
319 reg = <0x48044000 0x2000>;
320 interrupts = <92>;
321 ti,hwmods = "timer4";
322 };
323
324 timer5: timer@48046000 {
325 compatible = "ti,dm816-timer";
326 reg = <0x48046000 0x2000>;
327 interrupts = <93>;
328 ti,hwmods = "timer5";
329 };
330
331 timer6: timer@48048000 {
332 compatible = "ti,dm816-timer";
333 reg = <0x48048000 0x2000>;
334 interrupts = <94>;
335 ti,hwmods = "timer6";
336 };
337
338 timer7: timer@4804a000 {
339 compatible = "ti,dm816-timer";
340 reg = <0x4804a000 0x2000>;
341 interrupts = <95>;
342 ti,hwmods = "timer7";
343 };
344
345 uart1: uart@48020000 {
346 compatible = "ti,omap3-uart";
347 ti,hwmods = "uart1";
348 reg = <0x48020000 0x2000>;
349 clock-frequency = <48000000>;
350 interrupts = <72>;
351 dmas = <&edma 26 &edma 27>;
352 dma-names = "tx", "rx";
353 };
354
355 uart2: uart@48022000 {
356 compatible = "ti,omap3-uart";
357 ti,hwmods = "uart2";
358 reg = <0x48022000 0x2000>;
359 clock-frequency = <48000000>;
360 interrupts = <73>;
361 dmas = <&edma 28 &edma 29>;
362 dma-names = "tx", "rx";
363 };
364
365 uart3: uart@48024000 {
366 compatible = "ti,omap3-uart";
367 ti,hwmods = "uart3";
368 reg = <0x48024000 0x2000>;
369 clock-frequency = <48000000>;
370 interrupts = <74>;
371 dmas = <&edma 30 &edma 31>;
372 dma-names = "tx", "rx";
373 };
374
375 /* NOTE: USB needs a transceiver driver for phys to work */
376 usb: usb_otg_hs@47401000 {
377 compatible = "ti,am33xx-usb";
378 reg = <0x47401000 0x400000>;
379 ranges;
380 #address-cells = <1>;
381 #size-cells = <1>;
382 ti,hwmods = "usb_otg_hs";
383
384 usb0: usb@47401000 {
385 compatible = "ti,musb-am33xx";
386 reg = <0x47401400 0x400
387 0x47401000 0x200>;
388 reg-names = "mc", "control";
389 interrupts = <18>;
390 interrupt-names = "mc";
Tony Lindgrena54879a2015-02-24 08:48:52 -0800391 dr_mode = "host";
392 interface-type = <0>;
393 phys = <&usb_phy0>;
394 phy-names = "usb2-phy";
Tony Lindgren78000642015-01-19 11:47:35 -0800395 mentor,multipoint = <1>;
396 mentor,num-eps = <16>;
397 mentor,ram-bits = <12>;
398 mentor,power = <500>;
Tony Lindgrende1a1222015-03-19 09:14:36 -0700399
400 dmas = <&cppi41dma 0 0 &cppi41dma 1 0
401 &cppi41dma 2 0 &cppi41dma 3 0
402 &cppi41dma 4 0 &cppi41dma 5 0
403 &cppi41dma 6 0 &cppi41dma 7 0
404 &cppi41dma 8 0 &cppi41dma 9 0
405 &cppi41dma 10 0 &cppi41dma 11 0
406 &cppi41dma 12 0 &cppi41dma 13 0
407 &cppi41dma 14 0 &cppi41dma 0 1
408 &cppi41dma 1 1 &cppi41dma 2 1
409 &cppi41dma 3 1 &cppi41dma 4 1
410 &cppi41dma 5 1 &cppi41dma 6 1
411 &cppi41dma 7 1 &cppi41dma 8 1
412 &cppi41dma 9 1 &cppi41dma 10 1
413 &cppi41dma 11 1 &cppi41dma 12 1
414 &cppi41dma 13 1 &cppi41dma 14 1>;
415 dma-names =
416 "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
417 "rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
418 "rx14", "rx15",
419 "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
420 "tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
421 "tx14", "tx15";
Tony Lindgren78000642015-01-19 11:47:35 -0800422 };
423
424 usb1: usb@47401800 {
425 compatible = "ti,musb-am33xx";
Tony Lindgren78000642015-01-19 11:47:35 -0800426 reg = <0x47401c00 0x400
427 0x47401800 0x200>;
428 reg-names = "mc", "control";
429 interrupts = <19>;
430 interrupt-names = "mc";
Tony Lindgrena54879a2015-02-24 08:48:52 -0800431 dr_mode = "host";
432 interface-type = <0>;
433 phys = <&usb_phy1>;
434 phy-names = "usb2-phy";
Tony Lindgren78000642015-01-19 11:47:35 -0800435 mentor,multipoint = <1>;
436 mentor,num-eps = <16>;
437 mentor,ram-bits = <12>;
438 mentor,power = <500>;
Tony Lindgrende1a1222015-03-19 09:14:36 -0700439
440 dmas = <&cppi41dma 15 0 &cppi41dma 16 0
441 &cppi41dma 17 0 &cppi41dma 18 0
442 &cppi41dma 19 0 &cppi41dma 20 0
443 &cppi41dma 21 0 &cppi41dma 22 0
444 &cppi41dma 23 0 &cppi41dma 24 0
445 &cppi41dma 25 0 &cppi41dma 26 0
446 &cppi41dma 27 0 &cppi41dma 28 0
447 &cppi41dma 29 0 &cppi41dma 15 1
448 &cppi41dma 16 1 &cppi41dma 17 1
449 &cppi41dma 18 1 &cppi41dma 19 1
450 &cppi41dma 20 1 &cppi41dma 21 1
451 &cppi41dma 22 1 &cppi41dma 23 1
452 &cppi41dma 24 1 &cppi41dma 25 1
453 &cppi41dma 26 1 &cppi41dma 27 1
454 &cppi41dma 28 1 &cppi41dma 29 1>;
455 dma-names =
456 "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7",
457 "rx8", "rx9", "rx10", "rx11", "rx12", "rx13",
458 "rx14", "rx15",
459 "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7",
460 "tx8", "tx9", "tx10", "tx11", "tx12", "tx13",
461 "tx14", "tx15";
462 };
463
464 cppi41dma: dma-controller@47402000 {
465 compatible = "ti,am3359-cppi41";
466 reg = <0x47400000 0x1000
467 0x47402000 0x1000
468 0x47403000 0x1000
469 0x47404000 0x4000>;
470 reg-names = "glue", "controller", "scheduler", "queuemgr";
471 interrupts = <17>;
472 interrupt-names = "glue";
473 #dma-cells = <2>;
474 #dma-channels = <30>;
475 #dma-requests = <256>;
Tony Lindgren78000642015-01-19 11:47:35 -0800476 };
477 };
478
479 wd_timer2: wd_timer@480c2000 {
480 compatible = "ti,omap3-wdt";
481 ti,hwmods = "wd_timer";
482 reg = <0x480c2000 0x1000>;
483 interrupts = <0>;
484 };
485 };
486};
487
Tony Lindgren7383ca92015-01-19 11:47:35 -0800488#include "dm816x-clocks.dtsi"