arch/x86/Kconfig.debug

menu "Kernel hacking"

config TRACE_IRQFLAGS_SUPPORT
	def_bool y

source "lib/Kconfig.debug"

config EARLY_PRINTK
	bool "Early printk" if EMBEDDED
	default y
	help
	  Write kernel log output directly into the VGA buffer or to a serial
	  port.

	  This is useful for kernel debugging when your machine crashes very
	  early before the console code is initialized. For normal operation
	  it is not recommended because it looks ugly and doesn't cooperate
	  with klogd/syslogd or the X server. You should normally N here,
	  unless you want to debug such a crash.

config DEBUG_STACKOVERFLOW
	bool "Check for stack overflows"
	depends on DEBUG_KERNEL
	help
	  This option will cause messages to be printed if free stack space
	  drops below a certain limit.

config DEBUG_STACK_USAGE
	bool "Stack utilization instrumentation"
	depends on DEBUG_KERNEL
	help
	  Enables the display of the minimum amount of free stack which each
	  task has ever had available in the sysrq-T and sysrq-P debug output.

	  This option will slow down process creation somewhat.

comment "Page alloc debug is incompatible with Software Suspend on i386"
	depends on DEBUG_KERNEL && HIBERNATION
	depends on X86_32

config DEBUG_PAGEALLOC
	bool "Debug page memory allocations"
	depends on DEBUG_KERNEL && !HIBERNATION && !HUGETLBFS
	depends on X86_32
	help
	  Unmap pages from the kernel linear mapping after free_pages().
	  This results in a large slowdown, but helps to find certain types
	  of memory corruptions.

config DEBUG_RODATA
	bool "Write protect kernel read-only data structures"
	depends on DEBUG_KERNEL
	help
	  Mark the kernel read-only data as write-protected in the pagetables,
	  in order to catch accidental (and incorrect) writes to such const
	  data. This option may have a slight performance impact because a
	  portion of the kernel code won't be covered by a 2MB TLB anymore.
	  If in doubt, say "N".

config 4KSTACKS
	bool "Use 4Kb for kernel stacks instead of 8Kb"
	depends on DEBUG_KERNEL
	depends on X86_32
	help
	  If you say Y here the kernel will use a 4Kb stacksize for the
	  kernel stack attached to each process/thread. This facilitates
	  running more threads on a system and also reduces the pressure
	  on the VM subsystem for higher order allocations. This option
	  will also use IRQ stacks to compensate for the reduced stackspace.

config X86_FIND_SMP_CONFIG
	def_bool y
	depends on X86_LOCAL_APIC || X86_VOYAGER
	depends on X86_32

config X86_MPPARSE
	def_bool y
	depends on (X86_32 && (X86_LOCAL_APIC && !X86_VISWS)) || X86_64

config DOUBLEFAULT
	default y
	bool "Enable doublefault exception handler" if EMBEDDED
	depends on X86_32
	help
	  This option allows trapping of rare doublefault exceptions that
	  would otherwise cause a system to silently reboot. Disabling this
	  option saves about 4k and might cause you much additional grey
	  hair.

config IOMMU_DEBUG
	bool "Enable IOMMU debugging"
	depends on GART_IOMMU && DEBUG_KERNEL
	depends on X86_64
	help
	  Force the IOMMU to on even when you have less than 4GB of
	  memory and add debugging code. On overflow always panic. And
	  allow to enable IOMMU leak tracing. Can be disabled at boot
	  time with iommu=noforce. This will also enable scatter gather
	  list merging.  Currently not recommended for production
	  code. When you use it make sure you have a big enough
	  IOMMU/AGP aperture.  Most of the options enabled by this can
	  be set more finegrained using the iommu= command line
	  options. See Documentation/x86_64/boot-options.txt for more
	  details.

config IOMMU_LEAK
	bool "IOMMU leak tracing"
	depends on DEBUG_KERNEL
	depends on IOMMU_DEBUG
	help
	  Add a simple leak tracer to the IOMMU code. This is useful when you
	  are debugging a buggy device driver that leaks IOMMU mappings.

#
# IO delay types:
#

config IO_DELAY_TYPE_0X80
	int
	default "0"

config IO_DELAY_TYPE_0XED
	int
	default "1"

config IO_DELAY_TYPE_UDELAY
	int
	default "2"

config IO_DELAY_TYPE_NONE
	int
	default "3"

choice
	prompt "IO delay type"
	default IO_DELAY_0XED

config IO_DELAY_0X80
	bool "port 0x80 based port-IO delay [recommended]"
	help
	  This is the traditional Linux IO delay used for in/out_p.
	  It is the most tested hence safest selection here.

config IO_DELAY_0XED
	bool "port 0xed based port-IO delay"
	help
	  Use port 0xed as the IO delay. This frees up port 0x80 which is
	  often used as a hardware-debug port.

config IO_DELAY_UDELAY
	bool "udelay based port-IO delay"
	help
	  Use udelay(2) as the IO delay method. This provides the delay
	  while not having any side-effect on the IO port space.

config IO_DELAY_NONE
	bool "no port-IO delay"
	help
	  No port-IO delay. Will break on old boxes that require port-IO
	  delay for certain operations. Should work on most new machines.

endchoice

if IO_DELAY_0X80
config DEFAULT_IO_DELAY_TYPE
	int
	default IO_DELAY_TYPE_0X80
endif

if IO_DELAY_0XED
config DEFAULT_IO_DELAY_TYPE
	int
	default IO_DELAY_TYPE_0XED
endif

if IO_DELAY_UDELAY
config DEFAULT_IO_DELAY_TYPE
	int
	default IO_DELAY_TYPE_UDELAY
endif

if IO_DELAY_NONE
config DEFAULT_IO_DELAY_TYPE
	int
	default IO_DELAY_TYPE_NONE
endif

config DEBUG_BOOT_PARAMS
	bool "Debug boot parameters"
	depends on DEBUG_KERNEL
	depends on DEBUG_FS
	help
	  This option will cause struct boot_params to be exported via debugfs.

endmenu