blob: 4c945716a660d3e3884357409f1ab58c63fe9f92 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001LINUX HOTPLUGGING
2
3In hotpluggable busses like USB (and Cardbus PCI), end-users plug devices
4into the bus with power on. In most cases, users expect the devices to become
5immediately usable. That means the system must do many things, including:
6
7 - Find a driver that can handle the device. That may involve
8 loading a kernel module; newer drivers can use module-init-tools
9 to publish their device (and class) support to user utilities.
10
11 - Bind a driver to that device. Bus frameworks do that using a
12 device driver's probe() routine.
Andrea Gelminib03dbff2010-05-23 21:56:42 +020013
Linus Torvalds1da177e2005-04-16 15:20:36 -070014 - Tell other subsystems to configure the new device. Print
15 queues may need to be enabled, networks brought up, disk
16 partitions mounted, and so on. In some cases these will
17 be driver-specific actions.
18
19This involves a mix of kernel mode and user mode actions. Making devices
20be immediately usable means that any user mode actions can't wait for an
21administrator to do them: the kernel must trigger them, either passively
22(triggering some monitoring daemon to invoke a helper program) or
23actively (calling such a user mode helper program directly).
24
25Those triggered actions must support a system's administrative policies;
26such programs are called "policy agents" here. Typically they involve
27shell scripts that dispatch to more familiar administration tools.
28
29Because some of those actions rely on information about drivers (metadata)
30that is currently available only when the drivers are dynamically linked,
31you get the best hotplugging when you configure a highly modular system.
32
33
34KERNEL HOTPLUG HELPER (/sbin/hotplug)
35
36When you compile with CONFIG_HOTPLUG, you get a new kernel parameter:
37/proc/sys/kernel/hotplug, which normally holds the pathname "/sbin/hotplug".
38That parameter names a program which the kernel may invoke at various times.
39
40The /sbin/hotplug program can be invoked by any subsystem as part of its
41reaction to a configuration change, from a thread in that subsystem.
42Only one parameter is required: the name of a subsystem being notified of
43some kernel event. That name is used as the first key for further event
44dispatch; any other argument and environment parameters are specified by
45the subsystem making that invocation.
46
47Hotplug software and other resources is available at:
48
49 http://linux-hotplug.sourceforge.net
50
51Mailing list information is also available at that site.
52
53
54--------------------------------------------------------------------------
55
56
57USB POLICY AGENT
58
59The USB subsystem currently invokes /sbin/hotplug when USB devices
60are added or removed from system. The invocation is done by the kernel
61hub daemon thread [khubd], or else as part of root hub initialization
62(done by init, modprobe, kapmd, etc). Its single command line parameter
63is the string "usb", and it passes these environment variables:
64
65 ACTION ... "add", "remove"
66 PRODUCT ... USB vendor, product, and version codes (hex)
67 TYPE ... device class codes (decimal)
68 INTERFACE ... interface 0 class codes (decimal)
69
70If "usbdevfs" is configured, DEVICE and DEVFS are also passed. DEVICE is
71the pathname of the device, and is useful for devices with multiple and/or
72alternate interfaces that complicate driver selection. By design, USB
73hotplugging is independent of "usbdevfs": you can do most essential parts
74of USB device setup without using that filesystem, and without running a
75user mode daemon to detect changes in system configuration.
76
77Currently available policy agent implementations can load drivers for
78modules, and can invoke driver-specific setup scripts. The newest ones
79leverage USB module-init-tools support. Later agents might unload drivers.
80
81
82USB MODUTILS SUPPORT
83
84Current versions of module-init-tools will create a "modules.usbmap" file
85which contains the entries from each driver's MODULE_DEVICE_TABLE. Such
86files can be used by various user mode policy agents to make sure all the
Andrea Gelminib03dbff2010-05-23 21:56:42 +020087right driver modules get loaded, either at boot time or later.
Linus Torvalds1da177e2005-04-16 15:20:36 -070088
89See <linux/usb.h> for full information about such table entries; or look
90at existing drivers. Each table entry describes one or more criteria to
91be used when matching a driver to a device or class of devices. The
92specific criteria are identified by bits set in "match_flags", paired
93with field values. You can construct the criteria directly, or with
94macros such as these, and use driver_info to store more information.
95
96 USB_DEVICE (vendorId, productId)
97 ... matching devices with specified vendor and product ids
98 USB_DEVICE_VER (vendorId, productId, lo, hi)
99 ... like USB_DEVICE with lo <= productversion <= hi
100 USB_INTERFACE_INFO (class, subclass, protocol)
101 ... matching specified interface class info
102 USB_DEVICE_INFO (class, subclass, protocol)
103 ... matching specified device class info
104
105A short example, for a driver that supports several specific USB devices
106and their quirks, might have a MODULE_DEVICE_TABLE like this:
107
108 static const struct usb_device_id mydriver_id_table = {
109 { USB_DEVICE (0x9999, 0xaaaa), driver_info: QUIRK_X },
110 { USB_DEVICE (0xbbbb, 0x8888), driver_info: QUIRK_Y|QUIRK_Z },
111 ...
112 { } /* end with an all-zeroes entry */
113 }
114 MODULE_DEVICE_TABLE (usb, mydriver_id_table);
115
116Most USB device drivers should pass these tables to the USB subsystem as
117well as to the module management subsystem. Not all, though: some driver
118frameworks connect using interfaces layered over USB, and so they won't
119need such a "struct usb_driver".
120
121Drivers that connect directly to the USB subsystem should be declared
122something like this:
123
124 static struct usb_driver mydriver = {
125 .name = "mydriver",
126 .id_table = mydriver_id_table,
127 .probe = my_probe,
128 .disconnect = my_disconnect,
129
130 /*
131 if using the usb chardev framework:
132 .minor = MY_USB_MINOR_START,
133 .fops = my_file_ops,
134 if exposing any operations through usbdevfs:
135 .ioctl = my_ioctl,
136 */
137 }
138
139When the USB subsystem knows about a driver's device ID table, it's used when
140choosing drivers to probe(). The thread doing new device processing checks
141drivers' device ID entries from the MODULE_DEVICE_TABLE against interface and
142device descriptors for the device. It will only call probe() if there is a
143match, and the third argument to probe() will be the entry that matched.
144
145If you don't provide an id_table for your driver, then your driver may get
146probed for each new device; the third parameter to probe() will be null.
147
148