Baruch Siach | 2066930 | 2010-07-04 07:55:10 +0300 | [diff] [blame] | 1 | /* |
| 2 | * V4L2 Driver for i.MX27/i.MX25 camera host |
| 3 | * |
| 4 | * Copyright (C) 2008, Sascha Hauer, Pengutronix |
| 5 | * Copyright (C) 2010, Baruch Siach, Orex Computed Radiography |
| 6 | * |
| 7 | * This program is free software; you can redistribute it and/or modify |
| 8 | * it under the terms of the GNU General Public License as published by |
| 9 | * the Free Software Foundation; either version 2 of the License, or |
| 10 | * (at your option) any later version. |
| 11 | */ |
| 12 | |
| 13 | #include <linux/init.h> |
| 14 | #include <linux/module.h> |
| 15 | #include <linux/io.h> |
| 16 | #include <linux/delay.h> |
| 17 | #include <linux/slab.h> |
| 18 | #include <linux/dma-mapping.h> |
| 19 | #include <linux/errno.h> |
| 20 | #include <linux/fs.h> |
| 21 | #include <linux/interrupt.h> |
| 22 | #include <linux/kernel.h> |
| 23 | #include <linux/mm.h> |
| 24 | #include <linux/moduleparam.h> |
| 25 | #include <linux/time.h> |
| 26 | #include <linux/version.h> |
| 27 | #include <linux/device.h> |
| 28 | #include <linux/platform_device.h> |
| 29 | #include <linux/mutex.h> |
| 30 | #include <linux/clk.h> |
| 31 | |
| 32 | #include <media/v4l2-common.h> |
| 33 | #include <media/v4l2-dev.h> |
| 34 | #include <media/videobuf-dma-contig.h> |
| 35 | #include <media/soc_camera.h> |
| 36 | #include <media/soc_mediabus.h> |
| 37 | |
| 38 | #include <linux/videodev2.h> |
| 39 | |
| 40 | #include <mach/mx2_cam.h> |
| 41 | #ifdef CONFIG_MACH_MX27 |
| 42 | #include <mach/dma-mx1-mx2.h> |
| 43 | #endif |
| 44 | #include <mach/hardware.h> |
| 45 | |
| 46 | #include <asm/dma.h> |
| 47 | |
| 48 | #define MX2_CAM_DRV_NAME "mx2-camera" |
| 49 | #define MX2_CAM_VERSION_CODE KERNEL_VERSION(0, 0, 5) |
| 50 | #define MX2_CAM_DRIVER_DESCRIPTION "i.MX2x_Camera" |
| 51 | |
| 52 | /* reset values */ |
| 53 | #define CSICR1_RESET_VAL 0x40000800 |
| 54 | #define CSICR2_RESET_VAL 0x0 |
| 55 | #define CSICR3_RESET_VAL 0x0 |
| 56 | |
| 57 | /* csi control reg 1 */ |
| 58 | #define CSICR1_SWAP16_EN (1 << 31) |
| 59 | #define CSICR1_EXT_VSYNC (1 << 30) |
| 60 | #define CSICR1_EOF_INTEN (1 << 29) |
| 61 | #define CSICR1_PRP_IF_EN (1 << 28) |
| 62 | #define CSICR1_CCIR_MODE (1 << 27) |
| 63 | #define CSICR1_COF_INTEN (1 << 26) |
| 64 | #define CSICR1_SF_OR_INTEN (1 << 25) |
| 65 | #define CSICR1_RF_OR_INTEN (1 << 24) |
| 66 | #define CSICR1_STATFF_LEVEL (3 << 22) |
| 67 | #define CSICR1_STATFF_INTEN (1 << 21) |
| 68 | #define CSICR1_RXFF_LEVEL(l) (((l) & 3) << 19) /* MX27 */ |
| 69 | #define CSICR1_FB2_DMA_INTEN (1 << 20) /* MX25 */ |
| 70 | #define CSICR1_FB1_DMA_INTEN (1 << 19) /* MX25 */ |
| 71 | #define CSICR1_RXFF_INTEN (1 << 18) |
| 72 | #define CSICR1_SOF_POL (1 << 17) |
| 73 | #define CSICR1_SOF_INTEN (1 << 16) |
| 74 | #define CSICR1_MCLKDIV(d) (((d) & 0xF) << 12) |
| 75 | #define CSICR1_HSYNC_POL (1 << 11) |
| 76 | #define CSICR1_CCIR_EN (1 << 10) |
| 77 | #define CSICR1_MCLKEN (1 << 9) |
| 78 | #define CSICR1_FCC (1 << 8) |
| 79 | #define CSICR1_PACK_DIR (1 << 7) |
| 80 | #define CSICR1_CLR_STATFIFO (1 << 6) |
| 81 | #define CSICR1_CLR_RXFIFO (1 << 5) |
| 82 | #define CSICR1_GCLK_MODE (1 << 4) |
| 83 | #define CSICR1_INV_DATA (1 << 3) |
| 84 | #define CSICR1_INV_PCLK (1 << 2) |
| 85 | #define CSICR1_REDGE (1 << 1) |
| 86 | |
| 87 | #define SHIFT_STATFF_LEVEL 22 |
| 88 | #define SHIFT_RXFF_LEVEL 19 |
| 89 | #define SHIFT_MCLKDIV 12 |
| 90 | |
| 91 | /* control reg 3 */ |
| 92 | #define CSICR3_FRMCNT (0xFFFF << 16) |
| 93 | #define CSICR3_FRMCNT_RST (1 << 15) |
| 94 | #define CSICR3_DMA_REFLASH_RFF (1 << 14) |
| 95 | #define CSICR3_DMA_REFLASH_SFF (1 << 13) |
| 96 | #define CSICR3_DMA_REQ_EN_RFF (1 << 12) |
| 97 | #define CSICR3_DMA_REQ_EN_SFF (1 << 11) |
| 98 | #define CSICR3_RXFF_LEVEL(l) (((l) & 7) << 4) /* MX25 */ |
| 99 | #define CSICR3_CSI_SUP (1 << 3) |
| 100 | #define CSICR3_ZERO_PACK_EN (1 << 2) |
| 101 | #define CSICR3_ECC_INT_EN (1 << 1) |
| 102 | #define CSICR3_ECC_AUTO_EN (1 << 0) |
| 103 | |
| 104 | #define SHIFT_FRMCNT 16 |
| 105 | |
| 106 | /* csi status reg */ |
| 107 | #define CSISR_SFF_OR_INT (1 << 25) |
| 108 | #define CSISR_RFF_OR_INT (1 << 24) |
| 109 | #define CSISR_STATFF_INT (1 << 21) |
| 110 | #define CSISR_DMA_TSF_FB2_INT (1 << 20) /* MX25 */ |
| 111 | #define CSISR_DMA_TSF_FB1_INT (1 << 19) /* MX25 */ |
| 112 | #define CSISR_RXFF_INT (1 << 18) |
| 113 | #define CSISR_EOF_INT (1 << 17) |
| 114 | #define CSISR_SOF_INT (1 << 16) |
| 115 | #define CSISR_F2_INT (1 << 15) |
| 116 | #define CSISR_F1_INT (1 << 14) |
| 117 | #define CSISR_COF_INT (1 << 13) |
| 118 | #define CSISR_ECC_INT (1 << 1) |
| 119 | #define CSISR_DRDY (1 << 0) |
| 120 | |
| 121 | #define CSICR1 0x00 |
| 122 | #define CSICR2 0x04 |
| 123 | #define CSISR (cpu_is_mx27() ? 0x08 : 0x18) |
| 124 | #define CSISTATFIFO 0x0c |
| 125 | #define CSIRFIFO 0x10 |
| 126 | #define CSIRXCNT 0x14 |
| 127 | #define CSICR3 (cpu_is_mx27() ? 0x1C : 0x08) |
| 128 | #define CSIDMASA_STATFIFO 0x20 |
| 129 | #define CSIDMATA_STATFIFO 0x24 |
| 130 | #define CSIDMASA_FB1 0x28 |
| 131 | #define CSIDMASA_FB2 0x2c |
| 132 | #define CSIFBUF_PARA 0x30 |
| 133 | #define CSIIMAG_PARA 0x34 |
| 134 | |
| 135 | /* EMMA PrP */ |
| 136 | #define PRP_CNTL 0x00 |
| 137 | #define PRP_INTR_CNTL 0x04 |
| 138 | #define PRP_INTRSTATUS 0x08 |
| 139 | #define PRP_SOURCE_Y_PTR 0x0c |
| 140 | #define PRP_SOURCE_CB_PTR 0x10 |
| 141 | #define PRP_SOURCE_CR_PTR 0x14 |
| 142 | #define PRP_DEST_RGB1_PTR 0x18 |
| 143 | #define PRP_DEST_RGB2_PTR 0x1c |
| 144 | #define PRP_DEST_Y_PTR 0x20 |
| 145 | #define PRP_DEST_CB_PTR 0x24 |
| 146 | #define PRP_DEST_CR_PTR 0x28 |
| 147 | #define PRP_SRC_FRAME_SIZE 0x2c |
| 148 | #define PRP_DEST_CH1_LINE_STRIDE 0x30 |
| 149 | #define PRP_SRC_PIXEL_FORMAT_CNTL 0x34 |
| 150 | #define PRP_CH1_PIXEL_FORMAT_CNTL 0x38 |
| 151 | #define PRP_CH1_OUT_IMAGE_SIZE 0x3c |
| 152 | #define PRP_CH2_OUT_IMAGE_SIZE 0x40 |
| 153 | #define PRP_SRC_LINE_STRIDE 0x44 |
| 154 | #define PRP_CSC_COEF_012 0x48 |
| 155 | #define PRP_CSC_COEF_345 0x4c |
| 156 | #define PRP_CSC_COEF_678 0x50 |
| 157 | #define PRP_CH1_RZ_HORI_COEF1 0x54 |
| 158 | #define PRP_CH1_RZ_HORI_COEF2 0x58 |
| 159 | #define PRP_CH1_RZ_HORI_VALID 0x5c |
| 160 | #define PRP_CH1_RZ_VERT_COEF1 0x60 |
| 161 | #define PRP_CH1_RZ_VERT_COEF2 0x64 |
| 162 | #define PRP_CH1_RZ_VERT_VALID 0x68 |
| 163 | #define PRP_CH2_RZ_HORI_COEF1 0x6c |
| 164 | #define PRP_CH2_RZ_HORI_COEF2 0x70 |
| 165 | #define PRP_CH2_RZ_HORI_VALID 0x74 |
| 166 | #define PRP_CH2_RZ_VERT_COEF1 0x78 |
| 167 | #define PRP_CH2_RZ_VERT_COEF2 0x7c |
| 168 | #define PRP_CH2_RZ_VERT_VALID 0x80 |
| 169 | |
| 170 | #define PRP_CNTL_CH1EN (1 << 0) |
| 171 | #define PRP_CNTL_CH2EN (1 << 1) |
| 172 | #define PRP_CNTL_CSIEN (1 << 2) |
| 173 | #define PRP_CNTL_DATA_IN_YUV420 (0 << 3) |
| 174 | #define PRP_CNTL_DATA_IN_YUV422 (1 << 3) |
| 175 | #define PRP_CNTL_DATA_IN_RGB16 (2 << 3) |
| 176 | #define PRP_CNTL_DATA_IN_RGB32 (3 << 3) |
| 177 | #define PRP_CNTL_CH1_OUT_RGB8 (0 << 5) |
| 178 | #define PRP_CNTL_CH1_OUT_RGB16 (1 << 5) |
| 179 | #define PRP_CNTL_CH1_OUT_RGB32 (2 << 5) |
| 180 | #define PRP_CNTL_CH1_OUT_YUV422 (3 << 5) |
| 181 | #define PRP_CNTL_CH2_OUT_YUV420 (0 << 7) |
| 182 | #define PRP_CNTL_CH2_OUT_YUV422 (1 << 7) |
| 183 | #define PRP_CNTL_CH2_OUT_YUV444 (2 << 7) |
| 184 | #define PRP_CNTL_CH1_LEN (1 << 9) |
| 185 | #define PRP_CNTL_CH2_LEN (1 << 10) |
| 186 | #define PRP_CNTL_SKIP_FRAME (1 << 11) |
| 187 | #define PRP_CNTL_SWRST (1 << 12) |
| 188 | #define PRP_CNTL_CLKEN (1 << 13) |
| 189 | #define PRP_CNTL_WEN (1 << 14) |
| 190 | #define PRP_CNTL_CH1BYP (1 << 15) |
| 191 | #define PRP_CNTL_IN_TSKIP(x) ((x) << 16) |
| 192 | #define PRP_CNTL_CH1_TSKIP(x) ((x) << 19) |
| 193 | #define PRP_CNTL_CH2_TSKIP(x) ((x) << 22) |
| 194 | #define PRP_CNTL_INPUT_FIFO_LEVEL(x) ((x) << 25) |
| 195 | #define PRP_CNTL_RZ_FIFO_LEVEL(x) ((x) << 27) |
| 196 | #define PRP_CNTL_CH2B1EN (1 << 29) |
| 197 | #define PRP_CNTL_CH2B2EN (1 << 30) |
| 198 | #define PRP_CNTL_CH2FEN (1 << 31) |
| 199 | |
| 200 | /* IRQ Enable and status register */ |
| 201 | #define PRP_INTR_RDERR (1 << 0) |
| 202 | #define PRP_INTR_CH1WERR (1 << 1) |
| 203 | #define PRP_INTR_CH2WERR (1 << 2) |
| 204 | #define PRP_INTR_CH1FC (1 << 3) |
| 205 | #define PRP_INTR_CH2FC (1 << 5) |
| 206 | #define PRP_INTR_LBOVF (1 << 7) |
| 207 | #define PRP_INTR_CH2OVF (1 << 8) |
| 208 | |
| 209 | #define mx27_camera_emma(pcdev) (cpu_is_mx27() && pcdev->use_emma) |
| 210 | |
| 211 | #define MAX_VIDEO_MEM 16 |
| 212 | |
| 213 | struct mx2_camera_dev { |
| 214 | struct device *dev; |
| 215 | struct soc_camera_host soc_host; |
| 216 | struct soc_camera_device *icd; |
| 217 | struct clk *clk_csi, *clk_emma; |
| 218 | |
| 219 | unsigned int irq_csi, irq_emma; |
| 220 | void __iomem *base_csi, *base_emma; |
| 221 | unsigned long base_dma; |
| 222 | |
| 223 | struct mx2_camera_platform_data *pdata; |
| 224 | struct resource *res_csi, *res_emma; |
| 225 | unsigned long platform_flags; |
| 226 | |
| 227 | struct list_head capture; |
| 228 | struct list_head active_bufs; |
| 229 | |
| 230 | spinlock_t lock; |
| 231 | |
| 232 | int dma; |
| 233 | struct mx2_buffer *active; |
| 234 | struct mx2_buffer *fb1_active; |
| 235 | struct mx2_buffer *fb2_active; |
| 236 | |
| 237 | int use_emma; |
| 238 | |
| 239 | u32 csicr1; |
| 240 | |
Baruch Siach | 79d3c2c | 2010-07-27 08:03:30 +0300 | [diff] [blame] | 241 | void *discard_buffer; |
Baruch Siach | 2066930 | 2010-07-04 07:55:10 +0300 | [diff] [blame] | 242 | dma_addr_t discard_buffer_dma; |
| 243 | size_t discard_size; |
| 244 | }; |
| 245 | |
| 246 | /* buffer for one video frame */ |
| 247 | struct mx2_buffer { |
| 248 | /* common v4l buffer stuff -- must be first */ |
| 249 | struct videobuf_buffer vb; |
| 250 | |
| 251 | enum v4l2_mbus_pixelcode code; |
| 252 | |
| 253 | int bufnum; |
| 254 | }; |
| 255 | |
| 256 | static void mx2_camera_deactivate(struct mx2_camera_dev *pcdev) |
| 257 | { |
| 258 | unsigned long flags; |
| 259 | |
| 260 | clk_disable(pcdev->clk_csi); |
| 261 | writel(0, pcdev->base_csi + CSICR1); |
| 262 | if (mx27_camera_emma(pcdev)) { |
| 263 | writel(0, pcdev->base_emma + PRP_CNTL); |
| 264 | } else if (cpu_is_mx25()) { |
| 265 | spin_lock_irqsave(&pcdev->lock, flags); |
| 266 | pcdev->fb1_active = NULL; |
| 267 | pcdev->fb2_active = NULL; |
| 268 | writel(0, pcdev->base_csi + CSIDMASA_FB1); |
| 269 | writel(0, pcdev->base_csi + CSIDMASA_FB2); |
| 270 | spin_unlock_irqrestore(&pcdev->lock, flags); |
| 271 | } |
| 272 | } |
| 273 | |
| 274 | /* |
| 275 | * The following two functions absolutely depend on the fact, that |
| 276 | * there can be only one camera on mx2 camera sensor interface |
| 277 | */ |
| 278 | static int mx2_camera_add_device(struct soc_camera_device *icd) |
| 279 | { |
| 280 | struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); |
| 281 | struct mx2_camera_dev *pcdev = ici->priv; |
| 282 | int ret; |
| 283 | u32 csicr1; |
| 284 | |
| 285 | if (pcdev->icd) |
| 286 | return -EBUSY; |
| 287 | |
| 288 | ret = clk_enable(pcdev->clk_csi); |
| 289 | if (ret < 0) |
| 290 | return ret; |
| 291 | |
| 292 | csicr1 = CSICR1_MCLKEN; |
| 293 | |
| 294 | if (mx27_camera_emma(pcdev)) { |
| 295 | csicr1 |= CSICR1_PRP_IF_EN | CSICR1_FCC | |
| 296 | CSICR1_RXFF_LEVEL(0); |
| 297 | } else if (cpu_is_mx27()) |
| 298 | csicr1 |= CSICR1_SOF_INTEN | CSICR1_RXFF_LEVEL(2); |
| 299 | |
| 300 | pcdev->csicr1 = csicr1; |
| 301 | writel(pcdev->csicr1, pcdev->base_csi + CSICR1); |
| 302 | |
| 303 | pcdev->icd = icd; |
| 304 | |
| 305 | dev_info(icd->dev.parent, "Camera driver attached to camera %d\n", |
| 306 | icd->devnum); |
| 307 | |
| 308 | return 0; |
| 309 | } |
| 310 | |
| 311 | static void mx2_camera_remove_device(struct soc_camera_device *icd) |
| 312 | { |
| 313 | struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); |
| 314 | struct mx2_camera_dev *pcdev = ici->priv; |
| 315 | |
| 316 | BUG_ON(icd != pcdev->icd); |
| 317 | |
| 318 | dev_info(icd->dev.parent, "Camera driver detached from camera %d\n", |
| 319 | icd->devnum); |
| 320 | |
| 321 | mx2_camera_deactivate(pcdev); |
| 322 | |
| 323 | if (pcdev->discard_buffer) { |
| 324 | dma_free_coherent(ici->v4l2_dev.dev, pcdev->discard_size, |
| 325 | pcdev->discard_buffer, |
| 326 | pcdev->discard_buffer_dma); |
| 327 | pcdev->discard_buffer = NULL; |
| 328 | } |
| 329 | |
| 330 | pcdev->icd = NULL; |
| 331 | } |
| 332 | |
| 333 | #ifdef CONFIG_MACH_MX27 |
| 334 | static void mx27_camera_dma_enable(struct mx2_camera_dev *pcdev) |
| 335 | { |
| 336 | u32 tmp; |
| 337 | |
| 338 | imx_dma_enable(pcdev->dma); |
| 339 | |
| 340 | tmp = readl(pcdev->base_csi + CSICR1); |
| 341 | tmp |= CSICR1_RF_OR_INTEN; |
| 342 | writel(tmp, pcdev->base_csi + CSICR1); |
| 343 | } |
| 344 | |
| 345 | static irqreturn_t mx27_camera_irq(int irq_csi, void *data) |
| 346 | { |
| 347 | struct mx2_camera_dev *pcdev = data; |
| 348 | u32 status = readl(pcdev->base_csi + CSISR); |
| 349 | |
| 350 | if (status & CSISR_SOF_INT && pcdev->active) { |
| 351 | u32 tmp; |
| 352 | |
| 353 | tmp = readl(pcdev->base_csi + CSICR1); |
| 354 | writel(tmp | CSICR1_CLR_RXFIFO, pcdev->base_csi + CSICR1); |
| 355 | mx27_camera_dma_enable(pcdev); |
| 356 | } |
| 357 | |
| 358 | writel(CSISR_SOF_INT | CSISR_RFF_OR_INT, pcdev->base_csi + CSISR); |
| 359 | |
| 360 | return IRQ_HANDLED; |
| 361 | } |
| 362 | #else |
| 363 | static irqreturn_t mx27_camera_irq(int irq_csi, void *data) |
| 364 | { |
| 365 | return IRQ_NONE; |
| 366 | } |
| 367 | #endif /* CONFIG_MACH_MX27 */ |
| 368 | |
| 369 | static void mx25_camera_frame_done(struct mx2_camera_dev *pcdev, int fb, |
| 370 | int state) |
| 371 | { |
| 372 | struct videobuf_buffer *vb; |
| 373 | struct mx2_buffer *buf; |
| 374 | struct mx2_buffer **fb_active = fb == 1 ? &pcdev->fb1_active : |
| 375 | &pcdev->fb2_active; |
| 376 | u32 fb_reg = fb == 1 ? CSIDMASA_FB1 : CSIDMASA_FB2; |
| 377 | unsigned long flags; |
| 378 | |
| 379 | spin_lock_irqsave(&pcdev->lock, flags); |
| 380 | |
Baruch Siach | 5384a12 | 2010-07-27 09:06:07 -0300 | [diff] [blame] | 381 | if (*fb_active == NULL) |
| 382 | goto out; |
| 383 | |
Baruch Siach | 2066930 | 2010-07-04 07:55:10 +0300 | [diff] [blame] | 384 | vb = &(*fb_active)->vb; |
| 385 | dev_dbg(pcdev->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, |
| 386 | vb, vb->baddr, vb->bsize); |
| 387 | |
| 388 | vb->state = state; |
| 389 | do_gettimeofday(&vb->ts); |
| 390 | vb->field_count++; |
| 391 | |
| 392 | wake_up(&vb->done); |
| 393 | |
| 394 | if (list_empty(&pcdev->capture)) { |
| 395 | buf = NULL; |
| 396 | writel(0, pcdev->base_csi + fb_reg); |
| 397 | } else { |
| 398 | buf = list_entry(pcdev->capture.next, struct mx2_buffer, |
| 399 | vb.queue); |
| 400 | vb = &buf->vb; |
| 401 | list_del(&vb->queue); |
| 402 | vb->state = VIDEOBUF_ACTIVE; |
| 403 | writel(videobuf_to_dma_contig(vb), pcdev->base_csi + fb_reg); |
| 404 | } |
| 405 | |
| 406 | *fb_active = buf; |
| 407 | |
Baruch Siach | 5384a12 | 2010-07-27 09:06:07 -0300 | [diff] [blame] | 408 | out: |
Baruch Siach | 2066930 | 2010-07-04 07:55:10 +0300 | [diff] [blame] | 409 | spin_unlock_irqrestore(&pcdev->lock, flags); |
| 410 | } |
| 411 | |
| 412 | static irqreturn_t mx25_camera_irq(int irq_csi, void *data) |
| 413 | { |
| 414 | struct mx2_camera_dev *pcdev = data; |
| 415 | u32 status = readl(pcdev->base_csi + CSISR); |
| 416 | |
| 417 | if (status & CSISR_DMA_TSF_FB1_INT) |
| 418 | mx25_camera_frame_done(pcdev, 1, VIDEOBUF_DONE); |
| 419 | else if (status & CSISR_DMA_TSF_FB2_INT) |
| 420 | mx25_camera_frame_done(pcdev, 2, VIDEOBUF_DONE); |
| 421 | |
| 422 | /* FIXME: handle CSISR_RFF_OR_INT */ |
| 423 | |
| 424 | writel(status, pcdev->base_csi + CSISR); |
| 425 | |
| 426 | return IRQ_HANDLED; |
| 427 | } |
| 428 | |
| 429 | /* |
| 430 | * Videobuf operations |
| 431 | */ |
| 432 | static int mx2_videobuf_setup(struct videobuf_queue *vq, unsigned int *count, |
| 433 | unsigned int *size) |
| 434 | { |
| 435 | struct soc_camera_device *icd = vq->priv_data; |
| 436 | int bytes_per_line = soc_mbus_bytes_per_line(icd->user_width, |
| 437 | icd->current_fmt->host_fmt); |
| 438 | |
| 439 | dev_dbg(&icd->dev, "count=%d, size=%d\n", *count, *size); |
| 440 | |
| 441 | if (bytes_per_line < 0) |
| 442 | return bytes_per_line; |
| 443 | |
| 444 | *size = bytes_per_line * icd->user_height; |
| 445 | |
| 446 | if (0 == *count) |
| 447 | *count = 32; |
| 448 | if (*size * *count > MAX_VIDEO_MEM * 1024 * 1024) |
| 449 | *count = (MAX_VIDEO_MEM * 1024 * 1024) / *size; |
| 450 | |
| 451 | return 0; |
| 452 | } |
| 453 | |
| 454 | static void free_buffer(struct videobuf_queue *vq, struct mx2_buffer *buf) |
| 455 | { |
| 456 | struct soc_camera_device *icd = vq->priv_data; |
| 457 | struct videobuf_buffer *vb = &buf->vb; |
| 458 | |
| 459 | dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, |
| 460 | vb, vb->baddr, vb->bsize); |
| 461 | |
| 462 | /* |
| 463 | * This waits until this buffer is out of danger, i.e., until it is no |
| 464 | * longer in STATE_QUEUED or STATE_ACTIVE |
| 465 | */ |
| 466 | videobuf_waiton(vb, 0, 0); |
| 467 | |
| 468 | videobuf_dma_contig_free(vq, vb); |
| 469 | dev_dbg(&icd->dev, "%s freed\n", __func__); |
| 470 | |
| 471 | vb->state = VIDEOBUF_NEEDS_INIT; |
| 472 | } |
| 473 | |
| 474 | static int mx2_videobuf_prepare(struct videobuf_queue *vq, |
| 475 | struct videobuf_buffer *vb, enum v4l2_field field) |
| 476 | { |
| 477 | struct soc_camera_device *icd = vq->priv_data; |
| 478 | struct mx2_buffer *buf = container_of(vb, struct mx2_buffer, vb); |
| 479 | int bytes_per_line = soc_mbus_bytes_per_line(icd->user_width, |
| 480 | icd->current_fmt->host_fmt); |
| 481 | int ret = 0; |
| 482 | |
| 483 | dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, |
| 484 | vb, vb->baddr, vb->bsize); |
| 485 | |
| 486 | if (bytes_per_line < 0) |
| 487 | return bytes_per_line; |
| 488 | |
| 489 | #ifdef DEBUG |
| 490 | /* |
| 491 | * This can be useful if you want to see if we actually fill |
| 492 | * the buffer with something |
| 493 | */ |
| 494 | memset((void *)vb->baddr, 0xaa, vb->bsize); |
| 495 | #endif |
| 496 | |
| 497 | if (buf->code != icd->current_fmt->code || |
| 498 | vb->width != icd->user_width || |
| 499 | vb->height != icd->user_height || |
| 500 | vb->field != field) { |
| 501 | buf->code = icd->current_fmt->code; |
| 502 | vb->width = icd->user_width; |
| 503 | vb->height = icd->user_height; |
| 504 | vb->field = field; |
| 505 | vb->state = VIDEOBUF_NEEDS_INIT; |
| 506 | } |
| 507 | |
| 508 | vb->size = bytes_per_line * vb->height; |
| 509 | if (vb->baddr && vb->bsize < vb->size) { |
| 510 | ret = -EINVAL; |
| 511 | goto out; |
| 512 | } |
| 513 | |
| 514 | if (vb->state == VIDEOBUF_NEEDS_INIT) { |
| 515 | ret = videobuf_iolock(vq, vb, NULL); |
| 516 | if (ret) |
| 517 | goto fail; |
| 518 | |
| 519 | vb->state = VIDEOBUF_PREPARED; |
| 520 | } |
| 521 | |
| 522 | return 0; |
| 523 | |
| 524 | fail: |
| 525 | free_buffer(vq, buf); |
| 526 | out: |
| 527 | return ret; |
| 528 | } |
| 529 | |
| 530 | static void mx2_videobuf_queue(struct videobuf_queue *vq, |
| 531 | struct videobuf_buffer *vb) |
| 532 | { |
| 533 | struct soc_camera_device *icd = vq->priv_data; |
| 534 | struct soc_camera_host *ici = |
| 535 | to_soc_camera_host(icd->dev.parent); |
| 536 | struct mx2_camera_dev *pcdev = ici->priv; |
| 537 | struct mx2_buffer *buf = container_of(vb, struct mx2_buffer, vb); |
| 538 | unsigned long flags; |
| 539 | |
| 540 | dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, |
| 541 | vb, vb->baddr, vb->bsize); |
| 542 | |
| 543 | spin_lock_irqsave(&pcdev->lock, flags); |
| 544 | |
| 545 | vb->state = VIDEOBUF_QUEUED; |
| 546 | list_add_tail(&vb->queue, &pcdev->capture); |
| 547 | |
| 548 | if (mx27_camera_emma(pcdev)) { |
| 549 | goto out; |
| 550 | #ifdef CONFIG_MACH_MX27 |
| 551 | } else if (cpu_is_mx27()) { |
| 552 | int ret; |
| 553 | |
| 554 | if (pcdev->active == NULL) { |
| 555 | ret = imx_dma_setup_single(pcdev->dma, |
| 556 | videobuf_to_dma_contig(vb), vb->size, |
| 557 | (u32)pcdev->base_dma + 0x10, |
| 558 | DMA_MODE_READ); |
| 559 | if (ret) { |
| 560 | vb->state = VIDEOBUF_ERROR; |
| 561 | wake_up(&vb->done); |
| 562 | goto out; |
| 563 | } |
| 564 | |
| 565 | vb->state = VIDEOBUF_ACTIVE; |
| 566 | pcdev->active = buf; |
| 567 | } |
| 568 | #endif |
| 569 | } else { /* cpu_is_mx25() */ |
| 570 | u32 csicr3, dma_inten = 0; |
| 571 | |
| 572 | if (pcdev->fb1_active == NULL) { |
| 573 | writel(videobuf_to_dma_contig(vb), |
| 574 | pcdev->base_csi + CSIDMASA_FB1); |
| 575 | pcdev->fb1_active = buf; |
| 576 | dma_inten = CSICR1_FB1_DMA_INTEN; |
| 577 | } else if (pcdev->fb2_active == NULL) { |
| 578 | writel(videobuf_to_dma_contig(vb), |
| 579 | pcdev->base_csi + CSIDMASA_FB2); |
| 580 | pcdev->fb2_active = buf; |
| 581 | dma_inten = CSICR1_FB2_DMA_INTEN; |
| 582 | } |
| 583 | |
| 584 | if (dma_inten) { |
| 585 | list_del(&vb->queue); |
| 586 | vb->state = VIDEOBUF_ACTIVE; |
| 587 | |
| 588 | csicr3 = readl(pcdev->base_csi + CSICR3); |
| 589 | |
| 590 | /* Reflash DMA */ |
| 591 | writel(csicr3 | CSICR3_DMA_REFLASH_RFF, |
| 592 | pcdev->base_csi + CSICR3); |
| 593 | |
| 594 | /* clear & enable interrupts */ |
| 595 | writel(dma_inten, pcdev->base_csi + CSISR); |
| 596 | pcdev->csicr1 |= dma_inten; |
| 597 | writel(pcdev->csicr1, pcdev->base_csi + CSICR1); |
| 598 | |
| 599 | /* enable DMA */ |
| 600 | csicr3 |= CSICR3_DMA_REQ_EN_RFF | CSICR3_RXFF_LEVEL(1); |
| 601 | writel(csicr3, pcdev->base_csi + CSICR3); |
| 602 | } |
| 603 | } |
| 604 | |
| 605 | out: |
| 606 | spin_unlock_irqrestore(&pcdev->lock, flags); |
| 607 | } |
| 608 | |
| 609 | static void mx2_videobuf_release(struct videobuf_queue *vq, |
| 610 | struct videobuf_buffer *vb) |
| 611 | { |
| 612 | struct soc_camera_device *icd = vq->priv_data; |
| 613 | struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); |
| 614 | struct mx2_camera_dev *pcdev = ici->priv; |
| 615 | struct mx2_buffer *buf = container_of(vb, struct mx2_buffer, vb); |
| 616 | unsigned long flags; |
| 617 | |
| 618 | #ifdef DEBUG |
| 619 | dev_dbg(&icd->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, |
| 620 | vb, vb->baddr, vb->bsize); |
| 621 | |
| 622 | switch (vb->state) { |
| 623 | case VIDEOBUF_ACTIVE: |
| 624 | dev_info(&icd->dev, "%s (active)\n", __func__); |
| 625 | break; |
| 626 | case VIDEOBUF_QUEUED: |
| 627 | dev_info(&icd->dev, "%s (queued)\n", __func__); |
| 628 | break; |
| 629 | case VIDEOBUF_PREPARED: |
| 630 | dev_info(&icd->dev, "%s (prepared)\n", __func__); |
| 631 | break; |
| 632 | default: |
| 633 | dev_info(&icd->dev, "%s (unknown) %d\n", __func__, |
| 634 | vb->state); |
| 635 | break; |
| 636 | } |
| 637 | #endif |
| 638 | |
| 639 | /* |
| 640 | * Terminate only queued but inactive buffers. Active buffers are |
| 641 | * released when they become inactive after videobuf_waiton(). |
| 642 | * |
| 643 | * FIXME: implement forced termination of active buffers, so that the |
| 644 | * user won't get stuck in an uninterruptible state. This requires a |
| 645 | * specific handling for each of the three DMA types that this driver |
| 646 | * supports. |
| 647 | */ |
| 648 | spin_lock_irqsave(&pcdev->lock, flags); |
| 649 | if (vb->state == VIDEOBUF_QUEUED) { |
| 650 | list_del(&vb->queue); |
| 651 | vb->state = VIDEOBUF_ERROR; |
| 652 | } |
| 653 | spin_unlock_irqrestore(&pcdev->lock, flags); |
| 654 | |
| 655 | free_buffer(vq, buf); |
| 656 | } |
| 657 | |
| 658 | static struct videobuf_queue_ops mx2_videobuf_ops = { |
| 659 | .buf_setup = mx2_videobuf_setup, |
| 660 | .buf_prepare = mx2_videobuf_prepare, |
| 661 | .buf_queue = mx2_videobuf_queue, |
| 662 | .buf_release = mx2_videobuf_release, |
| 663 | }; |
| 664 | |
| 665 | static void mx2_camera_init_videobuf(struct videobuf_queue *q, |
| 666 | struct soc_camera_device *icd) |
| 667 | { |
| 668 | struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); |
| 669 | struct mx2_camera_dev *pcdev = ici->priv; |
| 670 | |
| 671 | videobuf_queue_dma_contig_init(q, &mx2_videobuf_ops, pcdev->dev, |
| 672 | &pcdev->lock, V4L2_BUF_TYPE_VIDEO_CAPTURE, |
| 673 | V4L2_FIELD_NONE, sizeof(struct mx2_buffer), icd); |
| 674 | } |
| 675 | |
| 676 | #define MX2_BUS_FLAGS (SOCAM_DATAWIDTH_8 | \ |
| 677 | SOCAM_MASTER | \ |
| 678 | SOCAM_VSYNC_ACTIVE_HIGH | \ |
| 679 | SOCAM_VSYNC_ACTIVE_LOW | \ |
| 680 | SOCAM_HSYNC_ACTIVE_HIGH | \ |
| 681 | SOCAM_HSYNC_ACTIVE_LOW | \ |
| 682 | SOCAM_PCLK_SAMPLE_RISING | \ |
| 683 | SOCAM_PCLK_SAMPLE_FALLING | \ |
| 684 | SOCAM_DATA_ACTIVE_HIGH | \ |
| 685 | SOCAM_DATA_ACTIVE_LOW) |
| 686 | |
| 687 | static int mx27_camera_emma_prp_reset(struct mx2_camera_dev *pcdev) |
| 688 | { |
| 689 | u32 cntl; |
| 690 | int count = 0; |
| 691 | |
| 692 | cntl = readl(pcdev->base_emma + PRP_CNTL); |
| 693 | writel(PRP_CNTL_SWRST, pcdev->base_emma + PRP_CNTL); |
| 694 | while (count++ < 100) { |
| 695 | if (!(readl(pcdev->base_emma + PRP_CNTL) & PRP_CNTL_SWRST)) |
| 696 | return 0; |
| 697 | barrier(); |
| 698 | udelay(1); |
| 699 | } |
| 700 | |
| 701 | return -ETIMEDOUT; |
| 702 | } |
| 703 | |
| 704 | static void mx27_camera_emma_buf_init(struct soc_camera_device *icd, |
| 705 | int bytesperline) |
| 706 | { |
| 707 | struct soc_camera_host *ici = |
| 708 | to_soc_camera_host(icd->dev.parent); |
| 709 | struct mx2_camera_dev *pcdev = ici->priv; |
| 710 | |
| 711 | writel(pcdev->discard_buffer_dma, |
| 712 | pcdev->base_emma + PRP_DEST_RGB1_PTR); |
| 713 | writel(pcdev->discard_buffer_dma, |
| 714 | pcdev->base_emma + PRP_DEST_RGB2_PTR); |
| 715 | |
| 716 | /* |
| 717 | * We only use the EMMA engine to get rid of the broken |
| 718 | * DMA Engine. No color space consversion at the moment. |
| 719 | * We adjust incoming and outgoing pixelformat to rgb16 |
| 720 | * and adjust the bytesperline accordingly. |
| 721 | */ |
| 722 | writel(PRP_CNTL_CH1EN | |
| 723 | PRP_CNTL_CSIEN | |
| 724 | PRP_CNTL_DATA_IN_RGB16 | |
| 725 | PRP_CNTL_CH1_OUT_RGB16 | |
| 726 | PRP_CNTL_CH1_LEN | |
| 727 | PRP_CNTL_CH1BYP | |
| 728 | PRP_CNTL_CH1_TSKIP(0) | |
| 729 | PRP_CNTL_IN_TSKIP(0), |
| 730 | pcdev->base_emma + PRP_CNTL); |
| 731 | |
| 732 | writel(((bytesperline >> 1) << 16) | icd->user_height, |
| 733 | pcdev->base_emma + PRP_SRC_FRAME_SIZE); |
| 734 | writel(((bytesperline >> 1) << 16) | icd->user_height, |
| 735 | pcdev->base_emma + PRP_CH1_OUT_IMAGE_SIZE); |
| 736 | writel(bytesperline, |
| 737 | pcdev->base_emma + PRP_DEST_CH1_LINE_STRIDE); |
| 738 | writel(0x2ca00565, /* RGB565 */ |
| 739 | pcdev->base_emma + PRP_SRC_PIXEL_FORMAT_CNTL); |
| 740 | writel(0x2ca00565, /* RGB565 */ |
| 741 | pcdev->base_emma + PRP_CH1_PIXEL_FORMAT_CNTL); |
| 742 | |
| 743 | /* Enable interrupts */ |
| 744 | writel(PRP_INTR_RDERR | |
| 745 | PRP_INTR_CH1WERR | |
| 746 | PRP_INTR_CH2WERR | |
| 747 | PRP_INTR_CH1FC | |
| 748 | PRP_INTR_CH2FC | |
| 749 | PRP_INTR_LBOVF | |
| 750 | PRP_INTR_CH2OVF, |
| 751 | pcdev->base_emma + PRP_INTR_CNTL); |
| 752 | } |
| 753 | |
| 754 | static int mx2_camera_set_bus_param(struct soc_camera_device *icd, |
| 755 | __u32 pixfmt) |
| 756 | { |
| 757 | struct soc_camera_host *ici = |
| 758 | to_soc_camera_host(icd->dev.parent); |
| 759 | struct mx2_camera_dev *pcdev = ici->priv; |
| 760 | unsigned long camera_flags, common_flags; |
| 761 | int ret = 0; |
| 762 | int bytesperline; |
| 763 | u32 csicr1 = pcdev->csicr1; |
| 764 | |
| 765 | camera_flags = icd->ops->query_bus_param(icd); |
| 766 | |
| 767 | common_flags = soc_camera_bus_param_compatible(camera_flags, |
| 768 | MX2_BUS_FLAGS); |
| 769 | if (!common_flags) |
| 770 | return -EINVAL; |
| 771 | |
| 772 | if ((common_flags & SOCAM_HSYNC_ACTIVE_HIGH) && |
| 773 | (common_flags & SOCAM_HSYNC_ACTIVE_LOW)) { |
| 774 | if (pcdev->platform_flags & MX2_CAMERA_HSYNC_HIGH) |
| 775 | common_flags &= ~SOCAM_HSYNC_ACTIVE_LOW; |
| 776 | else |
| 777 | common_flags &= ~SOCAM_HSYNC_ACTIVE_HIGH; |
| 778 | } |
| 779 | |
| 780 | if ((common_flags & SOCAM_PCLK_SAMPLE_RISING) && |
| 781 | (common_flags & SOCAM_PCLK_SAMPLE_FALLING)) { |
| 782 | if (pcdev->platform_flags & MX2_CAMERA_PCLK_SAMPLE_RISING) |
| 783 | common_flags &= ~SOCAM_PCLK_SAMPLE_FALLING; |
| 784 | else |
| 785 | common_flags &= ~SOCAM_PCLK_SAMPLE_RISING; |
| 786 | } |
| 787 | |
| 788 | ret = icd->ops->set_bus_param(icd, common_flags); |
| 789 | if (ret < 0) |
| 790 | return ret; |
| 791 | |
Michael Grzeschik | d86097e | 2010-08-03 06:37:55 -0300 | [diff] [blame] | 792 | if (common_flags & SOCAM_PCLK_SAMPLE_RISING) |
| 793 | csicr1 |= CSICR1_REDGE; |
Baruch Siach | 2066930 | 2010-07-04 07:55:10 +0300 | [diff] [blame] | 794 | if (common_flags & SOCAM_PCLK_SAMPLE_FALLING) |
| 795 | csicr1 |= CSICR1_INV_PCLK; |
| 796 | if (common_flags & SOCAM_VSYNC_ACTIVE_HIGH) |
| 797 | csicr1 |= CSICR1_SOF_POL; |
| 798 | if (common_flags & SOCAM_HSYNC_ACTIVE_HIGH) |
| 799 | csicr1 |= CSICR1_HSYNC_POL; |
| 800 | if (pcdev->platform_flags & MX2_CAMERA_SWAP16) |
| 801 | csicr1 |= CSICR1_SWAP16_EN; |
| 802 | if (pcdev->platform_flags & MX2_CAMERA_EXT_VSYNC) |
| 803 | csicr1 |= CSICR1_EXT_VSYNC; |
| 804 | if (pcdev->platform_flags & MX2_CAMERA_CCIR) |
| 805 | csicr1 |= CSICR1_CCIR_EN; |
| 806 | if (pcdev->platform_flags & MX2_CAMERA_CCIR_INTERLACE) |
| 807 | csicr1 |= CSICR1_CCIR_MODE; |
| 808 | if (pcdev->platform_flags & MX2_CAMERA_GATED_CLOCK) |
| 809 | csicr1 |= CSICR1_GCLK_MODE; |
| 810 | if (pcdev->platform_flags & MX2_CAMERA_INV_DATA) |
| 811 | csicr1 |= CSICR1_INV_DATA; |
| 812 | if (pcdev->platform_flags & MX2_CAMERA_PACK_DIR_MSB) |
| 813 | csicr1 |= CSICR1_PACK_DIR; |
| 814 | |
| 815 | pcdev->csicr1 = csicr1; |
| 816 | |
| 817 | bytesperline = soc_mbus_bytes_per_line(icd->user_width, |
| 818 | icd->current_fmt->host_fmt); |
| 819 | if (bytesperline < 0) |
| 820 | return bytesperline; |
| 821 | |
| 822 | if (mx27_camera_emma(pcdev)) { |
| 823 | ret = mx27_camera_emma_prp_reset(pcdev); |
| 824 | if (ret) |
| 825 | return ret; |
| 826 | |
| 827 | if (pcdev->discard_buffer) |
| 828 | dma_free_coherent(ici->v4l2_dev.dev, |
| 829 | pcdev->discard_size, pcdev->discard_buffer, |
| 830 | pcdev->discard_buffer_dma); |
| 831 | |
| 832 | /* |
| 833 | * I didn't manage to properly enable/disable the prp |
| 834 | * on a per frame basis during running transfers, |
| 835 | * thus we allocate a buffer here and use it to |
| 836 | * discard frames when no buffer is available. |
| 837 | * Feel free to work on this ;) |
| 838 | */ |
| 839 | pcdev->discard_size = icd->user_height * bytesperline; |
| 840 | pcdev->discard_buffer = dma_alloc_coherent(ici->v4l2_dev.dev, |
| 841 | pcdev->discard_size, &pcdev->discard_buffer_dma, |
| 842 | GFP_KERNEL); |
| 843 | if (!pcdev->discard_buffer) |
| 844 | return -ENOMEM; |
| 845 | |
| 846 | mx27_camera_emma_buf_init(icd, bytesperline); |
| 847 | } else if (cpu_is_mx25()) { |
| 848 | writel((bytesperline * icd->user_height) >> 2, |
| 849 | pcdev->base_csi + CSIRXCNT); |
| 850 | writel((bytesperline << 16) | icd->user_height, |
| 851 | pcdev->base_csi + CSIIMAG_PARA); |
| 852 | } |
| 853 | |
| 854 | writel(pcdev->csicr1, pcdev->base_csi + CSICR1); |
| 855 | |
| 856 | return 0; |
| 857 | } |
| 858 | |
| 859 | static int mx2_camera_set_crop(struct soc_camera_device *icd, |
| 860 | struct v4l2_crop *a) |
| 861 | { |
| 862 | struct v4l2_rect *rect = &a->c; |
| 863 | struct v4l2_subdev *sd = soc_camera_to_subdev(icd); |
| 864 | struct v4l2_mbus_framefmt mf; |
| 865 | int ret; |
| 866 | |
| 867 | soc_camera_limit_side(&rect->left, &rect->width, 0, 2, 4096); |
| 868 | soc_camera_limit_side(&rect->top, &rect->height, 0, 2, 4096); |
| 869 | |
| 870 | ret = v4l2_subdev_call(sd, video, s_crop, a); |
| 871 | if (ret < 0) |
| 872 | return ret; |
| 873 | |
| 874 | /* The capture device might have changed its output */ |
| 875 | ret = v4l2_subdev_call(sd, video, g_mbus_fmt, &mf); |
| 876 | if (ret < 0) |
| 877 | return ret; |
| 878 | |
| 879 | dev_dbg(icd->dev.parent, "Sensor cropped %dx%d\n", |
| 880 | mf.width, mf.height); |
| 881 | |
| 882 | icd->user_width = mf.width; |
| 883 | icd->user_height = mf.height; |
| 884 | |
| 885 | return ret; |
| 886 | } |
| 887 | |
| 888 | static int mx2_camera_set_fmt(struct soc_camera_device *icd, |
| 889 | struct v4l2_format *f) |
| 890 | { |
| 891 | struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); |
| 892 | struct mx2_camera_dev *pcdev = ici->priv; |
| 893 | struct v4l2_subdev *sd = soc_camera_to_subdev(icd); |
| 894 | const struct soc_camera_format_xlate *xlate; |
| 895 | struct v4l2_pix_format *pix = &f->fmt.pix; |
| 896 | struct v4l2_mbus_framefmt mf; |
| 897 | int ret; |
| 898 | |
| 899 | xlate = soc_camera_xlate_by_fourcc(icd, pix->pixelformat); |
| 900 | if (!xlate) { |
| 901 | dev_warn(icd->dev.parent, "Format %x not found\n", |
| 902 | pix->pixelformat); |
| 903 | return -EINVAL; |
| 904 | } |
| 905 | |
| 906 | /* eMMA can only do RGB565 */ |
| 907 | if (mx27_camera_emma(pcdev) && pix->pixelformat != V4L2_PIX_FMT_RGB565) |
| 908 | return -EINVAL; |
| 909 | |
| 910 | mf.width = pix->width; |
| 911 | mf.height = pix->height; |
| 912 | mf.field = pix->field; |
| 913 | mf.colorspace = pix->colorspace; |
| 914 | mf.code = xlate->code; |
| 915 | |
| 916 | ret = v4l2_subdev_call(sd, video, s_mbus_fmt, &mf); |
| 917 | if (ret < 0 && ret != -ENOIOCTLCMD) |
| 918 | return ret; |
| 919 | |
| 920 | if (mf.code != xlate->code) |
| 921 | return -EINVAL; |
| 922 | |
| 923 | pix->width = mf.width; |
| 924 | pix->height = mf.height; |
| 925 | pix->field = mf.field; |
| 926 | pix->colorspace = mf.colorspace; |
| 927 | icd->current_fmt = xlate; |
| 928 | |
| 929 | return 0; |
| 930 | } |
| 931 | |
| 932 | static int mx2_camera_try_fmt(struct soc_camera_device *icd, |
| 933 | struct v4l2_format *f) |
| 934 | { |
| 935 | struct soc_camera_host *ici = to_soc_camera_host(icd->dev.parent); |
| 936 | struct mx2_camera_dev *pcdev = ici->priv; |
| 937 | struct v4l2_subdev *sd = soc_camera_to_subdev(icd); |
| 938 | const struct soc_camera_format_xlate *xlate; |
| 939 | struct v4l2_pix_format *pix = &f->fmt.pix; |
| 940 | struct v4l2_mbus_framefmt mf; |
| 941 | __u32 pixfmt = pix->pixelformat; |
| 942 | unsigned int width_limit; |
| 943 | int ret; |
| 944 | |
| 945 | xlate = soc_camera_xlate_by_fourcc(icd, pixfmt); |
| 946 | if (pixfmt && !xlate) { |
| 947 | dev_warn(icd->dev.parent, "Format %x not found\n", pixfmt); |
| 948 | return -EINVAL; |
| 949 | } |
| 950 | |
| 951 | /* FIXME: implement MX27 limits */ |
| 952 | |
| 953 | /* eMMA can only do RGB565 */ |
| 954 | if (mx27_camera_emma(pcdev) && pixfmt != V4L2_PIX_FMT_RGB565) |
| 955 | return -EINVAL; |
| 956 | |
| 957 | /* limit to MX25 hardware capabilities */ |
| 958 | if (cpu_is_mx25()) { |
| 959 | if (xlate->host_fmt->bits_per_sample <= 8) |
| 960 | width_limit = 0xffff * 4; |
| 961 | else |
| 962 | width_limit = 0xffff * 2; |
| 963 | /* CSIIMAG_PARA limit */ |
| 964 | if (pix->width > width_limit) |
| 965 | pix->width = width_limit; |
| 966 | if (pix->height > 0xffff) |
| 967 | pix->height = 0xffff; |
| 968 | |
| 969 | pix->bytesperline = soc_mbus_bytes_per_line(pix->width, |
| 970 | xlate->host_fmt); |
| 971 | if (pix->bytesperline < 0) |
| 972 | return pix->bytesperline; |
| 973 | pix->sizeimage = pix->height * pix->bytesperline; |
| 974 | if (pix->sizeimage > (4 * 0x3ffff)) { /* CSIRXCNT limit */ |
| 975 | dev_warn(icd->dev.parent, |
| 976 | "Image size (%u) above limit\n", |
| 977 | pix->sizeimage); |
| 978 | return -EINVAL; |
| 979 | } |
| 980 | } |
| 981 | |
| 982 | /* limit to sensor capabilities */ |
| 983 | mf.width = pix->width; |
| 984 | mf.height = pix->height; |
| 985 | mf.field = pix->field; |
| 986 | mf.colorspace = pix->colorspace; |
| 987 | mf.code = xlate->code; |
| 988 | |
| 989 | ret = v4l2_subdev_call(sd, video, try_mbus_fmt, &mf); |
| 990 | if (ret < 0) |
| 991 | return ret; |
| 992 | |
| 993 | if (mf.field == V4L2_FIELD_ANY) |
| 994 | mf.field = V4L2_FIELD_NONE; |
| 995 | if (mf.field != V4L2_FIELD_NONE) { |
| 996 | dev_err(icd->dev.parent, "Field type %d unsupported.\n", |
| 997 | mf.field); |
| 998 | return -EINVAL; |
| 999 | } |
| 1000 | |
| 1001 | pix->width = mf.width; |
| 1002 | pix->height = mf.height; |
| 1003 | pix->field = mf.field; |
| 1004 | pix->colorspace = mf.colorspace; |
| 1005 | |
| 1006 | return 0; |
| 1007 | } |
| 1008 | |
| 1009 | static int mx2_camera_querycap(struct soc_camera_host *ici, |
| 1010 | struct v4l2_capability *cap) |
| 1011 | { |
| 1012 | /* cap->name is set by the friendly caller:-> */ |
| 1013 | strlcpy(cap->card, MX2_CAM_DRIVER_DESCRIPTION, sizeof(cap->card)); |
| 1014 | cap->version = MX2_CAM_VERSION_CODE; |
| 1015 | cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING; |
| 1016 | |
| 1017 | return 0; |
| 1018 | } |
| 1019 | |
| 1020 | static int mx2_camera_reqbufs(struct soc_camera_file *icf, |
| 1021 | struct v4l2_requestbuffers *p) |
| 1022 | { |
| 1023 | int i; |
| 1024 | |
| 1025 | for (i = 0; i < p->count; i++) { |
| 1026 | struct mx2_buffer *buf = container_of(icf->vb_vidq.bufs[i], |
| 1027 | struct mx2_buffer, vb); |
| 1028 | INIT_LIST_HEAD(&buf->vb.queue); |
| 1029 | } |
| 1030 | |
| 1031 | return 0; |
| 1032 | } |
| 1033 | |
| 1034 | #ifdef CONFIG_MACH_MX27 |
| 1035 | static void mx27_camera_frame_done(struct mx2_camera_dev *pcdev, int state) |
| 1036 | { |
| 1037 | struct videobuf_buffer *vb; |
| 1038 | struct mx2_buffer *buf; |
| 1039 | unsigned long flags; |
| 1040 | int ret; |
| 1041 | |
| 1042 | spin_lock_irqsave(&pcdev->lock, flags); |
| 1043 | |
| 1044 | if (!pcdev->active) { |
| 1045 | dev_err(pcdev->dev, "%s called with no active buffer!\n", |
| 1046 | __func__); |
| 1047 | goto out; |
| 1048 | } |
| 1049 | |
| 1050 | vb = &pcdev->active->vb; |
| 1051 | buf = container_of(vb, struct mx2_buffer, vb); |
| 1052 | WARN_ON(list_empty(&vb->queue)); |
| 1053 | dev_dbg(pcdev->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, |
| 1054 | vb, vb->baddr, vb->bsize); |
| 1055 | |
| 1056 | /* _init is used to debug races, see comment in pxa_camera_reqbufs() */ |
| 1057 | list_del_init(&vb->queue); |
| 1058 | vb->state = state; |
| 1059 | do_gettimeofday(&vb->ts); |
| 1060 | vb->field_count++; |
| 1061 | |
| 1062 | wake_up(&vb->done); |
| 1063 | |
| 1064 | if (list_empty(&pcdev->capture)) { |
| 1065 | pcdev->active = NULL; |
| 1066 | goto out; |
| 1067 | } |
| 1068 | |
| 1069 | pcdev->active = list_entry(pcdev->capture.next, |
| 1070 | struct mx2_buffer, vb.queue); |
| 1071 | |
| 1072 | vb = &pcdev->active->vb; |
| 1073 | vb->state = VIDEOBUF_ACTIVE; |
| 1074 | |
| 1075 | ret = imx_dma_setup_single(pcdev->dma, videobuf_to_dma_contig(vb), |
| 1076 | vb->size, (u32)pcdev->base_dma + 0x10, DMA_MODE_READ); |
| 1077 | |
| 1078 | if (ret) { |
| 1079 | vb->state = VIDEOBUF_ERROR; |
| 1080 | pcdev->active = NULL; |
| 1081 | wake_up(&vb->done); |
| 1082 | } |
| 1083 | |
| 1084 | out: |
| 1085 | spin_unlock_irqrestore(&pcdev->lock, flags); |
| 1086 | } |
| 1087 | |
| 1088 | static void mx27_camera_dma_err_callback(int channel, void *data, int err) |
| 1089 | { |
| 1090 | struct mx2_camera_dev *pcdev = data; |
| 1091 | |
| 1092 | mx27_camera_frame_done(pcdev, VIDEOBUF_ERROR); |
| 1093 | } |
| 1094 | |
| 1095 | static void mx27_camera_dma_callback(int channel, void *data) |
| 1096 | { |
| 1097 | struct mx2_camera_dev *pcdev = data; |
| 1098 | |
| 1099 | mx27_camera_frame_done(pcdev, VIDEOBUF_DONE); |
| 1100 | } |
| 1101 | |
| 1102 | #define DMA_REQ_CSI_RX 31 /* FIXME: Add this to a resource */ |
| 1103 | |
| 1104 | static int __devinit mx27_camera_dma_init(struct platform_device *pdev, |
| 1105 | struct mx2_camera_dev *pcdev) |
| 1106 | { |
| 1107 | int err; |
| 1108 | |
| 1109 | pcdev->dma = imx_dma_request_by_prio("CSI RX DMA", DMA_PRIO_HIGH); |
| 1110 | if (pcdev->dma < 0) { |
| 1111 | dev_err(&pdev->dev, "%s failed to request DMA channel\n", |
| 1112 | __func__); |
| 1113 | return pcdev->dma; |
| 1114 | } |
| 1115 | |
| 1116 | err = imx_dma_setup_handlers(pcdev->dma, mx27_camera_dma_callback, |
| 1117 | mx27_camera_dma_err_callback, pcdev); |
| 1118 | if (err) { |
| 1119 | dev_err(&pdev->dev, "%s failed to set DMA callback\n", |
| 1120 | __func__); |
| 1121 | goto err_out; |
| 1122 | } |
| 1123 | |
| 1124 | err = imx_dma_config_channel(pcdev->dma, |
| 1125 | IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_FIFO, |
| 1126 | IMX_DMA_MEMSIZE_32 | IMX_DMA_TYPE_LINEAR, |
| 1127 | DMA_REQ_CSI_RX, 1); |
| 1128 | if (err) { |
| 1129 | dev_err(&pdev->dev, "%s failed to config DMA channel\n", |
| 1130 | __func__); |
| 1131 | goto err_out; |
| 1132 | } |
| 1133 | |
| 1134 | imx_dma_config_burstlen(pcdev->dma, 64); |
| 1135 | |
| 1136 | return 0; |
| 1137 | |
| 1138 | err_out: |
| 1139 | imx_dma_free(pcdev->dma); |
| 1140 | |
| 1141 | return err; |
| 1142 | } |
| 1143 | #endif /* CONFIG_MACH_MX27 */ |
| 1144 | |
| 1145 | static unsigned int mx2_camera_poll(struct file *file, poll_table *pt) |
| 1146 | { |
| 1147 | struct soc_camera_file *icf = file->private_data; |
| 1148 | |
| 1149 | return videobuf_poll_stream(file, &icf->vb_vidq, pt); |
| 1150 | } |
| 1151 | |
| 1152 | static struct soc_camera_host_ops mx2_soc_camera_host_ops = { |
| 1153 | .owner = THIS_MODULE, |
| 1154 | .add = mx2_camera_add_device, |
| 1155 | .remove = mx2_camera_remove_device, |
| 1156 | .set_fmt = mx2_camera_set_fmt, |
| 1157 | .set_crop = mx2_camera_set_crop, |
| 1158 | .try_fmt = mx2_camera_try_fmt, |
| 1159 | .init_videobuf = mx2_camera_init_videobuf, |
| 1160 | .reqbufs = mx2_camera_reqbufs, |
| 1161 | .poll = mx2_camera_poll, |
| 1162 | .querycap = mx2_camera_querycap, |
| 1163 | .set_bus_param = mx2_camera_set_bus_param, |
| 1164 | }; |
| 1165 | |
| 1166 | static void mx27_camera_frame_done_emma(struct mx2_camera_dev *pcdev, |
| 1167 | int bufnum, int state) |
| 1168 | { |
| 1169 | struct mx2_buffer *buf; |
| 1170 | struct videobuf_buffer *vb; |
| 1171 | unsigned long phys; |
| 1172 | |
| 1173 | if (!list_empty(&pcdev->active_bufs)) { |
| 1174 | buf = list_entry(pcdev->active_bufs.next, |
| 1175 | struct mx2_buffer, vb.queue); |
| 1176 | |
| 1177 | BUG_ON(buf->bufnum != bufnum); |
| 1178 | |
| 1179 | vb = &buf->vb; |
| 1180 | #ifdef DEBUG |
| 1181 | phys = videobuf_to_dma_contig(vb); |
| 1182 | if (readl(pcdev->base_emma + PRP_DEST_RGB1_PTR + 4 * bufnum) |
| 1183 | != phys) { |
| 1184 | dev_err(pcdev->dev, "%p != %p\n", phys, |
| 1185 | readl(pcdev->base_emma + |
| 1186 | PRP_DEST_RGB1_PTR + |
| 1187 | 4 * bufnum)); |
| 1188 | } |
| 1189 | #endif |
| 1190 | dev_dbg(pcdev->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__, vb, |
| 1191 | vb->baddr, vb->bsize); |
| 1192 | |
| 1193 | list_del(&vb->queue); |
| 1194 | vb->state = state; |
| 1195 | do_gettimeofday(&vb->ts); |
| 1196 | vb->field_count++; |
| 1197 | |
| 1198 | wake_up(&vb->done); |
| 1199 | } |
| 1200 | |
| 1201 | if (list_empty(&pcdev->capture)) { |
| 1202 | writel(pcdev->discard_buffer_dma, pcdev->base_emma + |
| 1203 | PRP_DEST_RGB1_PTR + 4 * bufnum); |
| 1204 | return; |
| 1205 | } |
| 1206 | |
| 1207 | buf = list_entry(pcdev->capture.next, |
| 1208 | struct mx2_buffer, vb.queue); |
| 1209 | |
Michael Grzeschik | cd9ebdb | 2010-08-03 06:37:54 -0300 | [diff] [blame] | 1210 | buf->bufnum = !bufnum; |
Baruch Siach | 2066930 | 2010-07-04 07:55:10 +0300 | [diff] [blame] | 1211 | |
| 1212 | list_move_tail(pcdev->capture.next, &pcdev->active_bufs); |
| 1213 | |
| 1214 | vb = &buf->vb; |
| 1215 | vb->state = VIDEOBUF_ACTIVE; |
| 1216 | |
| 1217 | phys = videobuf_to_dma_contig(vb); |
| 1218 | writel(phys, pcdev->base_emma + PRP_DEST_RGB1_PTR + 4 * bufnum); |
| 1219 | } |
| 1220 | |
| 1221 | static irqreturn_t mx27_camera_emma_irq(int irq_emma, void *data) |
| 1222 | { |
| 1223 | struct mx2_camera_dev *pcdev = data; |
| 1224 | unsigned int status = readl(pcdev->base_emma + PRP_INTRSTATUS); |
| 1225 | struct mx2_buffer *buf; |
| 1226 | |
| 1227 | if (status & (1 << 7)) { /* overflow */ |
| 1228 | u32 cntl; |
| 1229 | /* |
| 1230 | * We only disable channel 1 here since this is the only |
| 1231 | * enabled channel |
| 1232 | * |
| 1233 | * FIXME: the correct DMA overflow handling should be resetting |
| 1234 | * the buffer, returning an error frame, and continuing with |
| 1235 | * the next one. |
| 1236 | */ |
| 1237 | cntl = readl(pcdev->base_emma + PRP_CNTL); |
| 1238 | writel(cntl & ~PRP_CNTL_CH1EN, pcdev->base_emma + PRP_CNTL); |
| 1239 | writel(cntl, pcdev->base_emma + PRP_CNTL); |
| 1240 | } |
| 1241 | if ((status & (3 << 5)) == (3 << 5) |
| 1242 | && !list_empty(&pcdev->active_bufs)) { |
| 1243 | /* |
| 1244 | * Both buffers have triggered, process the one we're expecting |
| 1245 | * to first |
| 1246 | */ |
| 1247 | buf = list_entry(pcdev->active_bufs.next, |
| 1248 | struct mx2_buffer, vb.queue); |
| 1249 | mx27_camera_frame_done_emma(pcdev, buf->bufnum, VIDEOBUF_DONE); |
| 1250 | status &= ~(1 << (6 - buf->bufnum)); /* mark processed */ |
| 1251 | } |
| 1252 | if (status & (1 << 6)) |
| 1253 | mx27_camera_frame_done_emma(pcdev, 0, VIDEOBUF_DONE); |
| 1254 | if (status & (1 << 5)) |
| 1255 | mx27_camera_frame_done_emma(pcdev, 1, VIDEOBUF_DONE); |
| 1256 | |
| 1257 | writel(status, pcdev->base_emma + PRP_INTRSTATUS); |
| 1258 | |
| 1259 | return IRQ_HANDLED; |
| 1260 | } |
| 1261 | |
| 1262 | static int __devinit mx27_camera_emma_init(struct mx2_camera_dev *pcdev) |
| 1263 | { |
| 1264 | struct resource *res_emma = pcdev->res_emma; |
| 1265 | int err = 0; |
| 1266 | |
| 1267 | if (!request_mem_region(res_emma->start, resource_size(res_emma), |
| 1268 | MX2_CAM_DRV_NAME)) { |
| 1269 | err = -EBUSY; |
| 1270 | goto out; |
| 1271 | } |
| 1272 | |
| 1273 | pcdev->base_emma = ioremap(res_emma->start, resource_size(res_emma)); |
| 1274 | if (!pcdev->base_emma) { |
| 1275 | err = -ENOMEM; |
| 1276 | goto exit_release; |
| 1277 | } |
| 1278 | |
| 1279 | err = request_irq(pcdev->irq_emma, mx27_camera_emma_irq, 0, |
| 1280 | MX2_CAM_DRV_NAME, pcdev); |
| 1281 | if (err) { |
| 1282 | dev_err(pcdev->dev, "Camera EMMA interrupt register failed \n"); |
| 1283 | goto exit_iounmap; |
| 1284 | } |
| 1285 | |
| 1286 | pcdev->clk_emma = clk_get(NULL, "emma"); |
| 1287 | if (IS_ERR(pcdev->clk_emma)) { |
| 1288 | err = PTR_ERR(pcdev->clk_emma); |
| 1289 | goto exit_free_irq; |
| 1290 | } |
| 1291 | |
| 1292 | clk_enable(pcdev->clk_emma); |
| 1293 | |
| 1294 | err = mx27_camera_emma_prp_reset(pcdev); |
| 1295 | if (err) |
| 1296 | goto exit_clk_emma_put; |
| 1297 | |
| 1298 | return err; |
| 1299 | |
| 1300 | exit_clk_emma_put: |
| 1301 | clk_disable(pcdev->clk_emma); |
| 1302 | clk_put(pcdev->clk_emma); |
| 1303 | exit_free_irq: |
| 1304 | free_irq(pcdev->irq_emma, pcdev); |
| 1305 | exit_iounmap: |
| 1306 | iounmap(pcdev->base_emma); |
| 1307 | exit_release: |
| 1308 | release_mem_region(res_emma->start, resource_size(res_emma)); |
| 1309 | out: |
| 1310 | return err; |
| 1311 | } |
| 1312 | |
| 1313 | static int __devinit mx2_camera_probe(struct platform_device *pdev) |
| 1314 | { |
| 1315 | struct mx2_camera_dev *pcdev; |
| 1316 | struct resource *res_csi, *res_emma; |
| 1317 | void __iomem *base_csi; |
| 1318 | int irq_csi, irq_emma; |
| 1319 | irq_handler_t mx2_cam_irq_handler = cpu_is_mx25() ? mx25_camera_irq |
| 1320 | : mx27_camera_irq; |
| 1321 | int err = 0; |
| 1322 | |
| 1323 | dev_dbg(&pdev->dev, "initialising\n"); |
| 1324 | |
| 1325 | res_csi = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| 1326 | irq_csi = platform_get_irq(pdev, 0); |
| 1327 | if (res_csi == NULL || irq_csi < 0) { |
| 1328 | dev_err(&pdev->dev, "Missing platform resources data\n"); |
| 1329 | err = -ENODEV; |
| 1330 | goto exit; |
| 1331 | } |
| 1332 | |
| 1333 | pcdev = kzalloc(sizeof(*pcdev), GFP_KERNEL); |
| 1334 | if (!pcdev) { |
| 1335 | dev_err(&pdev->dev, "Could not allocate pcdev\n"); |
| 1336 | err = -ENOMEM; |
| 1337 | goto exit; |
| 1338 | } |
| 1339 | |
| 1340 | pcdev->clk_csi = clk_get(&pdev->dev, NULL); |
| 1341 | if (IS_ERR(pcdev->clk_csi)) { |
| 1342 | err = PTR_ERR(pcdev->clk_csi); |
| 1343 | goto exit_kfree; |
| 1344 | } |
| 1345 | |
| 1346 | dev_dbg(&pdev->dev, "Camera clock frequency: %ld\n", |
| 1347 | clk_get_rate(pcdev->clk_csi)); |
| 1348 | |
| 1349 | /* Initialize DMA */ |
| 1350 | #ifdef CONFIG_MACH_MX27 |
| 1351 | if (cpu_is_mx27()) { |
| 1352 | err = mx27_camera_dma_init(pdev, pcdev); |
| 1353 | if (err) |
| 1354 | goto exit_clk_put; |
| 1355 | } |
| 1356 | #endif /* CONFIG_MACH_MX27 */ |
| 1357 | |
| 1358 | pcdev->res_csi = res_csi; |
| 1359 | pcdev->pdata = pdev->dev.platform_data; |
| 1360 | if (pcdev->pdata) { |
| 1361 | long rate; |
| 1362 | |
| 1363 | pcdev->platform_flags = pcdev->pdata->flags; |
| 1364 | |
| 1365 | rate = clk_round_rate(pcdev->clk_csi, pcdev->pdata->clk * 2); |
| 1366 | if (rate <= 0) { |
| 1367 | err = -ENODEV; |
| 1368 | goto exit_dma_free; |
| 1369 | } |
| 1370 | err = clk_set_rate(pcdev->clk_csi, rate); |
| 1371 | if (err < 0) |
| 1372 | goto exit_dma_free; |
| 1373 | } |
| 1374 | |
| 1375 | INIT_LIST_HEAD(&pcdev->capture); |
| 1376 | INIT_LIST_HEAD(&pcdev->active_bufs); |
| 1377 | spin_lock_init(&pcdev->lock); |
| 1378 | |
| 1379 | /* |
| 1380 | * Request the regions. |
| 1381 | */ |
| 1382 | if (!request_mem_region(res_csi->start, resource_size(res_csi), |
| 1383 | MX2_CAM_DRV_NAME)) { |
| 1384 | err = -EBUSY; |
| 1385 | goto exit_dma_free; |
| 1386 | } |
| 1387 | |
| 1388 | base_csi = ioremap(res_csi->start, resource_size(res_csi)); |
| 1389 | if (!base_csi) { |
| 1390 | err = -ENOMEM; |
| 1391 | goto exit_release; |
| 1392 | } |
| 1393 | pcdev->irq_csi = irq_csi; |
| 1394 | pcdev->base_csi = base_csi; |
| 1395 | pcdev->base_dma = res_csi->start; |
| 1396 | pcdev->dev = &pdev->dev; |
| 1397 | |
| 1398 | err = request_irq(pcdev->irq_csi, mx2_cam_irq_handler, 0, |
| 1399 | MX2_CAM_DRV_NAME, pcdev); |
| 1400 | if (err) { |
| 1401 | dev_err(pcdev->dev, "Camera interrupt register failed \n"); |
| 1402 | goto exit_iounmap; |
| 1403 | } |
| 1404 | |
| 1405 | if (cpu_is_mx27()) { |
| 1406 | /* EMMA support */ |
| 1407 | res_emma = platform_get_resource(pdev, IORESOURCE_MEM, 1); |
| 1408 | irq_emma = platform_get_irq(pdev, 1); |
| 1409 | |
| 1410 | if (res_emma && irq_emma >= 0) { |
| 1411 | dev_info(&pdev->dev, "Using EMMA\n"); |
| 1412 | pcdev->use_emma = 1; |
| 1413 | pcdev->res_emma = res_emma; |
| 1414 | pcdev->irq_emma = irq_emma; |
| 1415 | if (mx27_camera_emma_init(pcdev)) |
| 1416 | goto exit_free_irq; |
| 1417 | } |
| 1418 | } |
| 1419 | |
| 1420 | pcdev->soc_host.drv_name = MX2_CAM_DRV_NAME, |
| 1421 | pcdev->soc_host.ops = &mx2_soc_camera_host_ops, |
| 1422 | pcdev->soc_host.priv = pcdev; |
| 1423 | pcdev->soc_host.v4l2_dev.dev = &pdev->dev; |
| 1424 | pcdev->soc_host.nr = pdev->id; |
| 1425 | err = soc_camera_host_register(&pcdev->soc_host); |
| 1426 | if (err) |
| 1427 | goto exit_free_emma; |
| 1428 | |
| 1429 | return 0; |
| 1430 | |
| 1431 | exit_free_emma: |
| 1432 | if (mx27_camera_emma(pcdev)) { |
| 1433 | free_irq(pcdev->irq_emma, pcdev); |
| 1434 | clk_disable(pcdev->clk_emma); |
| 1435 | clk_put(pcdev->clk_emma); |
| 1436 | iounmap(pcdev->base_emma); |
| 1437 | release_mem_region(res_emma->start, resource_size(res_emma)); |
| 1438 | } |
| 1439 | exit_free_irq: |
| 1440 | free_irq(pcdev->irq_csi, pcdev); |
| 1441 | exit_iounmap: |
| 1442 | iounmap(base_csi); |
| 1443 | exit_release: |
| 1444 | release_mem_region(res_csi->start, resource_size(res_csi)); |
| 1445 | exit_dma_free: |
| 1446 | #ifdef CONFIG_MACH_MX27 |
| 1447 | if (cpu_is_mx27()) |
| 1448 | imx_dma_free(pcdev->dma); |
| 1449 | exit_clk_put: |
| 1450 | clk_put(pcdev->clk_csi); |
| 1451 | #endif /* CONFIG_MACH_MX27 */ |
| 1452 | exit_kfree: |
| 1453 | kfree(pcdev); |
| 1454 | exit: |
| 1455 | return err; |
| 1456 | } |
| 1457 | |
| 1458 | static int __devexit mx2_camera_remove(struct platform_device *pdev) |
| 1459 | { |
| 1460 | struct soc_camera_host *soc_host = to_soc_camera_host(&pdev->dev); |
| 1461 | struct mx2_camera_dev *pcdev = container_of(soc_host, |
| 1462 | struct mx2_camera_dev, soc_host); |
| 1463 | struct resource *res; |
| 1464 | |
| 1465 | clk_put(pcdev->clk_csi); |
| 1466 | #ifdef CONFIG_MACH_MX27 |
| 1467 | if (cpu_is_mx27()) |
| 1468 | imx_dma_free(pcdev->dma); |
| 1469 | #endif /* CONFIG_MACH_MX27 */ |
| 1470 | free_irq(pcdev->irq_csi, pcdev); |
| 1471 | if (mx27_camera_emma(pcdev)) |
| 1472 | free_irq(pcdev->irq_emma, pcdev); |
| 1473 | |
| 1474 | soc_camera_host_unregister(&pcdev->soc_host); |
| 1475 | |
| 1476 | iounmap(pcdev->base_csi); |
| 1477 | |
| 1478 | if (mx27_camera_emma(pcdev)) { |
| 1479 | clk_disable(pcdev->clk_emma); |
| 1480 | clk_put(pcdev->clk_emma); |
| 1481 | iounmap(pcdev->base_emma); |
| 1482 | res = pcdev->res_emma; |
| 1483 | release_mem_region(res->start, resource_size(res)); |
| 1484 | } |
| 1485 | |
| 1486 | res = pcdev->res_csi; |
| 1487 | release_mem_region(res->start, resource_size(res)); |
| 1488 | |
| 1489 | kfree(pcdev); |
| 1490 | |
| 1491 | dev_info(&pdev->dev, "MX2 Camera driver unloaded\n"); |
| 1492 | |
| 1493 | return 0; |
| 1494 | } |
| 1495 | |
| 1496 | static struct platform_driver mx2_camera_driver = { |
| 1497 | .driver = { |
| 1498 | .name = MX2_CAM_DRV_NAME, |
| 1499 | }, |
| 1500 | .remove = __devexit_p(mx2_camera_remove), |
| 1501 | }; |
| 1502 | |
| 1503 | |
| 1504 | static int __init mx2_camera_init(void) |
| 1505 | { |
| 1506 | return platform_driver_probe(&mx2_camera_driver, &mx2_camera_probe); |
| 1507 | } |
| 1508 | |
| 1509 | static void __exit mx2_camera_exit(void) |
| 1510 | { |
| 1511 | return platform_driver_unregister(&mx2_camera_driver); |
| 1512 | } |
| 1513 | |
| 1514 | module_init(mx2_camera_init); |
| 1515 | module_exit(mx2_camera_exit); |
| 1516 | |
| 1517 | MODULE_DESCRIPTION("i.MX27/i.MX25 SoC Camera Host driver"); |
| 1518 | MODULE_AUTHOR("Sascha Hauer <sha@pengutronix.de>"); |
| 1519 | MODULE_LICENSE("GPL"); |