blob: f10baabbf5db5ae2f266aed4f7559d258962f267 [file] [log] [blame]
Jeff Garzik669a5db2006-08-29 18:12:40 -04001/*
2 * IDE tuning and bus mastering support for the CS5510/CS5520
3 * chipsets
4 *
5 * The CS5510/CS5520 are slightly unusual devices. Unlike the
6 * typical IDE controllers they do bus mastering with the drive in
7 * PIO mode and smarter silicon.
8 *
9 * The practical upshot of this is that we must always tune the
10 * drive for the right PIO mode. We must also ignore all the blacklists
11 * and the drive bus mastering DMA information. Also to confuse matters
12 * further we can do DMA on PIO only drives.
13 *
14 * DMA on the 5510 also requires we disable_hlt() during DMA on early
15 * revisions.
16 *
17 * *** This driver is strictly experimental ***
18 *
19 * (c) Copyright Red Hat Inc 2002
20 *
21 * This program is free software; you can redistribute it and/or modify it
22 * under the terms of the GNU General Public License as published by the
23 * Free Software Foundation; either version 2, or (at your option) any
24 * later version.
25 *
26 * This program is distributed in the hope that it will be useful, but
27 * WITHOUT ANY WARRANTY; without even the implied warranty of
28 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
29 * General Public License for more details.
30 *
31 * Documentation:
Lucas De Marchi25985ed2011-03-30 22:57:33 -030032 * Not publicly available.
Jeff Garzik669a5db2006-08-29 18:12:40 -040033 */
34#include <linux/kernel.h>
35#include <linux/module.h>
36#include <linux/pci.h>
37#include <linux/init.h>
38#include <linux/blkdev.h>
39#include <linux/delay.h>
40#include <scsi/scsi_host.h>
41#include <linux/libata.h>
42
43#define DRV_NAME "pata_cs5520"
Jeff Garzik2a3103c2007-08-31 04:54:06 -040044#define DRV_VERSION "0.6.6"
Jeff Garzik669a5db2006-08-29 18:12:40 -040045
46struct pio_clocks
47{
48 int address;
49 int assert;
50 int recovery;
51};
52
53static const struct pio_clocks cs5520_pio_clocks[]={
54 {3, 6, 11},
55 {2, 5, 6},
56 {1, 4, 3},
57 {1, 3, 2},
58 {1, 2, 1}
59};
60
61/**
62 * cs5520_set_timings - program PIO timings
63 * @ap: ATA port
64 * @adev: ATA device
65 *
66 * Program the PIO mode timings for the controller according to the pio
67 * clocking table.
68 */
69
70static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio)
71{
72 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
73 int slave = adev->devno;
74
75 pio -= XFER_PIO_0;
76
77 /* Channel command timing */
78 pci_write_config_byte(pdev, 0x62 + ap->port_no,
79 (cs5520_pio_clocks[pio].recovery << 4) |
80 (cs5520_pio_clocks[pio].assert));
81 /* FIXME: should these use address ? */
82 /* Read command timing */
83 pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave,
84 (cs5520_pio_clocks[pio].recovery << 4) |
85 (cs5520_pio_clocks[pio].assert));
86 /* Write command timing */
87 pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave,
88 (cs5520_pio_clocks[pio].recovery << 4) |
89 (cs5520_pio_clocks[pio].assert));
90}
91
92/**
Jeff Garzik669a5db2006-08-29 18:12:40 -040093 * cs5520_set_piomode - program PIO timings
94 * @ap: ATA port
95 * @adev: ATA device
96 *
97 * Program the PIO mode timings for the controller according to the pio
Bartlomiej Zolnierkiewicz940a68d2009-12-03 20:32:09 +010098 * clocking table.
Jeff Garzik669a5db2006-08-29 18:12:40 -040099 */
100
101static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
102{
103 cs5520_set_timings(ap, adev, adev->pio_mode);
104}
105
Jeff Garzik669a5db2006-08-29 18:12:40 -0400106static struct scsi_host_template cs5520_sht = {
Tejun Heo68d1d072008-03-25 12:22:49 +0900107 ATA_BMDMA_SHT(DRV_NAME),
Alan Coxd26fc952007-07-06 19:13:52 -0400108 .sg_tablesize = LIBATA_DUMB_MAX_PRD,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400109};
110
111static struct ata_port_operations cs5520_port_ops = {
Tejun Heo029cfd62008-03-25 12:22:49 +0900112 .inherits = &ata_bmdma_port_ops,
Tejun Heof47451c2010-05-10 21:41:40 +0200113 .qc_prep = ata_bmdma_dumb_qc_prep,
Tejun Heo029cfd62008-03-25 12:22:49 +0900114 .cable_detect = ata_cable_40wire,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400115 .set_piomode = cs5520_set_piomode,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400116};
117
Greg Kroah-Hartman0ec24912012-12-21 13:19:58 -0800118static int cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400119{
Tejun Heocbcdd872007-08-18 13:14:55 +0900120 static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
121 static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
Tejun Heo5d728822007-04-17 23:44:08 +0900122 struct ata_port_info pi = {
123 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100124 .pio_mask = ATA_PIO4,
Tejun Heo5d728822007-04-17 23:44:08 +0900125 .port_ops = &cs5520_port_ops,
126 };
127 const struct ata_port_info *ppi[2];
Jeff Garzik669a5db2006-08-29 18:12:40 -0400128 u8 pcicfg;
Al Viro4ca4e432007-12-30 09:32:22 +0000129 void __iomem *iomap[5];
Tejun Heo5d728822007-04-17 23:44:08 +0900130 struct ata_host *host;
131 struct ata_ioports *ioaddr;
132 int i, rc;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400133
Tejun Heof08048e2008-03-25 12:22:47 +0900134 rc = pcim_enable_device(pdev);
135 if (rc)
136 return rc;
137
Jeff Garzik669a5db2006-08-29 18:12:40 -0400138 /* IDE port enable bits */
Tejun Heo5d728822007-04-17 23:44:08 +0900139 pci_read_config_byte(pdev, 0x60, &pcicfg);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400140
141 /* Check if the ATA ports are enabled */
142 if ((pcicfg & 3) == 0)
143 return -ENODEV;
144
Tejun Heo5d728822007-04-17 23:44:08 +0900145 ppi[0] = ppi[1] = &ata_dummy_port_info;
146 if (pcicfg & 1)
147 ppi[0] = &pi;
148 if (pcicfg & 2)
149 ppi[1] = &pi;
150
Jeff Garzik669a5db2006-08-29 18:12:40 -0400151 if ((pcicfg & 0x40) == 0) {
Joe Perchesa44fec12011-04-15 15:51:58 -0700152 dev_warn(&pdev->dev, "DMA mode disabled. Enabling.\n");
Tejun Heo5d728822007-04-17 23:44:08 +0900153 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400154 }
155
Tejun Heo5d728822007-04-17 23:44:08 +0900156 pi.mwdma_mask = id->driver_data;
157
158 host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
159 if (!host)
160 return -ENOMEM;
161
Jeff Garzik669a5db2006-08-29 18:12:40 -0400162 /* Perform set up for DMA */
Benjamin Herrenschmidt09483912007-12-20 15:28:09 +1100163 if (pci_enable_device_io(pdev)) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400164 printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
165 return -ENODEV;
166 }
Tejun Heo5d728822007-04-17 23:44:08 +0900167
Yang Hongyang284901a2009-04-06 19:01:15 -0700168 if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400169 printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
170 return -ENODEV;
171 }
Yang Hongyang284901a2009-04-06 19:01:15 -0700172 if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400173 printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
174 return -ENODEV;
175 }
176
Tejun Heo5d728822007-04-17 23:44:08 +0900177 /* Map IO ports and initialize host accordingly */
Tejun Heocbcdd872007-08-18 13:14:55 +0900178 iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
179 iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
180 iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
181 iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
Tejun Heo5d728822007-04-17 23:44:08 +0900182 iomap[4] = pcim_iomap(pdev, 2, 0);
Tejun Heo0d5ff562007-02-01 15:06:36 +0900183
184 if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
185 return -ENOMEM;
186
Tejun Heo5d728822007-04-17 23:44:08 +0900187 ioaddr = &host->ports[0]->ioaddr;
188 ioaddr->cmd_addr = iomap[0];
189 ioaddr->ctl_addr = iomap[1];
190 ioaddr->altstatus_addr = iomap[1];
191 ioaddr->bmdma_addr = iomap[4];
Tejun Heo9363c382008-04-07 22:47:16 +0900192 ata_sff_std_ports(ioaddr);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400193
Tejun Heocbcdd872007-08-18 13:14:55 +0900194 ata_port_desc(host->ports[0],
195 "cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
196 ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
197
Tejun Heo5d728822007-04-17 23:44:08 +0900198 ioaddr = &host->ports[1]->ioaddr;
199 ioaddr->cmd_addr = iomap[2];
200 ioaddr->ctl_addr = iomap[3];
201 ioaddr->altstatus_addr = iomap[3];
202 ioaddr->bmdma_addr = iomap[4] + 8;
Tejun Heo9363c382008-04-07 22:47:16 +0900203 ata_sff_std_ports(ioaddr);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400204
Tejun Heocbcdd872007-08-18 13:14:55 +0900205 ata_port_desc(host->ports[1],
206 "cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
207 ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
208
Tejun Heo5d728822007-04-17 23:44:08 +0900209 /* activate the host */
210 pci_set_master(pdev);
211 rc = ata_host_start(host);
212 if (rc)
213 return rc;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400214
Tejun Heo5d728822007-04-17 23:44:08 +0900215 for (i = 0; i < 2; i++) {
216 static const int irq[] = { 14, 15 };
Alan Cox8c6b0652007-07-20 15:36:31 +0100217 struct ata_port *ap = host->ports[i];
Jeff Garzik669a5db2006-08-29 18:12:40 -0400218
Tejun Heo5d728822007-04-17 23:44:08 +0900219 if (ata_port_is_dummy(ap))
220 continue;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400221
Tejun Heo5d728822007-04-17 23:44:08 +0900222 rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
Tejun Heoc3b28892010-05-19 22:10:21 +0200223 ata_bmdma_interrupt, 0, DRV_NAME, host);
Tejun Heo5d728822007-04-17 23:44:08 +0900224 if (rc)
225 return rc;
Tejun Heo40318262007-07-03 01:38:47 +0900226
Tejun Heocbcdd872007-08-18 13:14:55 +0900227 ata_port_desc(ap, "irq %d", irq[i]);
Tejun Heo5d728822007-04-17 23:44:08 +0900228 }
229
230 return ata_host_register(host, &cs5520_sht);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400231}
232
Tejun Heo438ac6d2007-03-02 17:31:26 +0900233#ifdef CONFIG_PM
Alan85011202006-11-22 17:01:06 +0000234/**
235 * cs5520_reinit_one - device resume
236 * @pdev: PCI device
237 *
238 * Do any reconfiguration work needed by a resume from RAM. We need
239 * to restore DMA mode support on BIOSen which disabled it
240 */
Jeff Garzikf20b16f2006-12-11 11:14:06 -0500241
Alan85011202006-11-22 17:01:06 +0000242static int cs5520_reinit_one(struct pci_dev *pdev)
243{
Jingoo Han0a86e1c2013-06-03 14:05:36 +0900244 struct ata_host *host = pci_get_drvdata(pdev);
Alan85011202006-11-22 17:01:06 +0000245 u8 pcicfg;
Tejun Heof08048e2008-03-25 12:22:47 +0900246 int rc;
247
248 rc = ata_pci_device_do_resume(pdev);
249 if (rc)
250 return rc;
251
Alan85011202006-11-22 17:01:06 +0000252 pci_read_config_byte(pdev, 0x60, &pcicfg);
253 if ((pcicfg & 0x40) == 0)
254 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
Tejun Heof08048e2008-03-25 12:22:47 +0900255
256 ata_host_resume(host);
257 return 0;
Alan85011202006-11-22 17:01:06 +0000258}
Alanaa6de492007-02-20 17:44:25 +0000259
260/**
261 * cs5520_pci_device_suspend - device suspend
262 * @pdev: PCI device
263 *
264 * We have to cut and waste bits from the standard method because
265 * the 5520 is a bit odd and not just a pure ATA device. As a result
266 * we must not disable it. The needed code is short and this avoids
267 * chip specific mess in the core code.
268 */
269
270static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
271{
Jingoo Han0a86e1c2013-06-03 14:05:36 +0900272 struct ata_host *host = pci_get_drvdata(pdev);
Alanaa6de492007-02-20 17:44:25 +0000273 int rc = 0;
274
275 rc = ata_host_suspend(host, mesg);
276 if (rc)
277 return rc;
278
279 pci_save_state(pdev);
280 return 0;
281}
Tejun Heo438ac6d2007-03-02 17:31:26 +0900282#endif /* CONFIG_PM */
Jeff Garzika84471f2007-02-26 05:51:33 -0500283
Jeff Garzik669a5db2006-08-29 18:12:40 -0400284/* For now keep DMA off. We can set it for all but A rev CS5510 once the
285 core ATA code can handle it */
286
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400287static const struct pci_device_id pata_cs5520[] = {
288 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
289 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
290
291 { },
Jeff Garzik669a5db2006-08-29 18:12:40 -0400292};
293
294static struct pci_driver cs5520_pci_driver = {
295 .name = DRV_NAME,
296 .id_table = pata_cs5520,
297 .probe = cs5520_init_one,
Jeff Garzik28555682007-10-11 17:12:35 -0400298 .remove = ata_pci_remove_one,
Tejun Heo438ac6d2007-03-02 17:31:26 +0900299#ifdef CONFIG_PM
Alanaa6de492007-02-20 17:44:25 +0000300 .suspend = cs5520_pci_device_suspend,
Alan85011202006-11-22 17:01:06 +0000301 .resume = cs5520_reinit_one,
Tejun Heo438ac6d2007-03-02 17:31:26 +0900302#endif
Jeff Garzik669a5db2006-08-29 18:12:40 -0400303};
304
Axel Lin2fc75da2012-04-19 13:43:05 +0800305module_pci_driver(cs5520_pci_driver);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400306
307MODULE_AUTHOR("Alan Cox");
308MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
309MODULE_LICENSE("GPL");
310MODULE_DEVICE_TABLE(pci, pata_cs5520);
311MODULE_VERSION(DRV_VERSION);