Caesar Wang | 6962ad5 | 2014-11-24 12:58:58 +0800 | [diff] [blame] | 1 | * Temperature Sensor ADC (TSADC) on rockchip SoCs |
| 2 | |
| 3 | Required properties: |
Caesar Wang | a519c27 | 2015-11-05 13:17:57 +0800 | [diff] [blame] | 4 | - compatible : should be "rockchip,<name>-tsadc" |
Caesar Wang | 4be0253 | 2015-12-03 16:48:41 +0800 | [diff] [blame] | 5 | "rockchip,rk3228-tsadc": found on RK3228 SoCs |
Caesar Wang | a519c27 | 2015-11-05 13:17:57 +0800 | [diff] [blame] | 6 | "rockchip,rk3288-tsadc": found on RK3288 SoCs |
| 7 | "rockchip,rk3368-tsadc": found on RK3368 SoCs |
Caesar Wang | 4be0253 | 2015-12-03 16:48:41 +0800 | [diff] [blame] | 8 | "rockchip,rk3399-tsadc": found on RK3399 SoCs |
Caesar Wang | 6962ad5 | 2014-11-24 12:58:58 +0800 | [diff] [blame] | 9 | - reg : physical base address of the controller and length of memory mapped |
| 10 | region. |
| 11 | - interrupts : The interrupt number to the cpu. The interrupt specifier format |
| 12 | depends on the interrupt controller. |
| 13 | - clocks : Must contain an entry for each entry in clock-names. |
| 14 | - clock-names : Shall be "tsadc" for the converter-clock, and "apb_pclk" for |
| 15 | the peripheral clock. |
| 16 | - resets : Must contain an entry for each entry in reset-names. |
| 17 | See ../reset/reset.txt for details. |
| 18 | - reset-names : Must include the name "tsadc-apb". |
Caesar Wang | 9aba783 | 2015-10-23 19:25:26 +0800 | [diff] [blame] | 19 | - pinctrl-names : The pin control state names; |
| 20 | - pinctrl-0 : The "init" pinctrl state, it will be set before device probe. |
| 21 | - pinctrl-1 : The "default" pinctrl state, it will be set after reset the |
| 22 | TSADC controller. |
| 23 | - pinctrl-2 : The "sleep" pinctrl state, it will be in for suspend. |
Caesar Wang | 6962ad5 | 2014-11-24 12:58:58 +0800 | [diff] [blame] | 24 | - #thermal-sensor-cells : Should be 1. See ./thermal.txt for a description. |
| 25 | - rockchip,hw-tshut-temp : The hardware-controlled shutdown temperature value. |
| 26 | - rockchip,hw-tshut-mode : The hardware-controlled shutdown mode 0:CRU 1:GPIO. |
| 27 | - rockchip,hw-tshut-polarity : The hardware-controlled active polarity 0:LOW |
| 28 | 1:HIGH. |
| 29 | |
| 30 | Exiample: |
| 31 | tsadc: tsadc@ff280000 { |
| 32 | compatible = "rockchip,rk3288-tsadc"; |
| 33 | reg = <0xff280000 0x100>; |
| 34 | interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| 35 | clocks = <&cru SCLK_TSADC>, <&cru PCLK_TSADC>; |
| 36 | clock-names = "tsadc", "apb_pclk"; |
| 37 | resets = <&cru SRST_TSADC>; |
| 38 | reset-names = "tsadc-apb"; |
Caesar Wang | 9aba783 | 2015-10-23 19:25:26 +0800 | [diff] [blame] | 39 | pinctrl-names = "init", "default", "sleep"; |
| 40 | pinctrl-0 = <&otp_gpio>; |
| 41 | pinctrl-1 = <&otp_out>; |
| 42 | pinctrl-2 = <&otp_gpio>; |
Caesar Wang | 6962ad5 | 2014-11-24 12:58:58 +0800 | [diff] [blame] | 43 | #thermal-sensor-cells = <1>; |
| 44 | rockchip,hw-tshut-temp = <95000>; |
| 45 | rockchip,hw-tshut-mode = <0>; |
| 46 | rockchip,hw-tshut-polarity = <0>; |
| 47 | }; |
| 48 | |
| 49 | Example: referring to thermal sensors: |
| 50 | thermal-zones { |
| 51 | cpu_thermal: cpu_thermal { |
| 52 | polling-delay-passive = <1000>; /* milliseconds */ |
| 53 | polling-delay = <5000>; /* milliseconds */ |
| 54 | |
| 55 | /* sensor ID */ |
| 56 | thermal-sensors = <&tsadc 1>; |
| 57 | |
| 58 | trips { |
| 59 | cpu_alert0: cpu_alert { |
| 60 | temperature = <70000>; /* millicelsius */ |
| 61 | hysteresis = <2000>; /* millicelsius */ |
| 62 | type = "passive"; |
| 63 | }; |
| 64 | cpu_crit: cpu_crit { |
| 65 | temperature = <90000>; /* millicelsius */ |
| 66 | hysteresis = <2000>; /* millicelsius */ |
| 67 | type = "critical"; |
| 68 | }; |
| 69 | }; |
| 70 | |
| 71 | cooling-maps { |
| 72 | map0 { |
| 73 | trip = <&cpu_alert0>; |
| 74 | cooling-device = |
| 75 | <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| 76 | }; |
| 77 | }; |
| 78 | }; |
| 79 | }; |