| Jeff Kirsher | 33f810b | 2011-07-31 00:06:29 -0700 | [diff] [blame] | 1 | # |
| 2 | # FDDI network device configuration |
| 3 | # |
| 4 | |
| 5 | config FDDI |
| 6 | tristate "FDDI driver support" |
| 7 | depends on PCI || EISA || TC |
| 8 | ---help--- |
| 9 | Fiber Distributed Data Interface is a high speed local area network |
| 10 | design; essentially a replacement for high speed Ethernet. FDDI can |
| 11 | run over copper or fiber. If you are connected to such a network and |
| 12 | want a driver for the FDDI card in your computer, say Y here (and |
| 13 | then also Y to the driver for your FDDI card, below). Most people |
| 14 | will say N. |
| 15 | |
| 16 | if FDDI |
| 17 | |
| 18 | config DEFXX |
| 19 | tristate "Digital DEFTA/DEFEA/DEFPA adapter support" |
| 20 | depends on FDDI && (PCI || EISA || TC) |
| 21 | ---help--- |
| 22 | This is support for the DIGITAL series of TURBOchannel (DEFTA), |
| 23 | EISA (DEFEA) and PCI (DEFPA) controllers which can connect you |
| 24 | to a local FDDI network. |
| 25 | |
| 26 | To compile this driver as a module, choose M here: the module |
| 27 | will be called defxx. If unsure, say N. |
| 28 | |
| 29 | config DEFXX_MMIO |
| 30 | bool |
| 31 | prompt "Use MMIO instead of PIO" if PCI || EISA |
| 32 | depends on DEFXX |
| 33 | default n if PCI || EISA |
| 34 | default y |
| 35 | ---help--- |
| 36 | This instructs the driver to use EISA or PCI memory-mapped I/O |
| 37 | (MMIO) as appropriate instead of programmed I/O ports (PIO). |
| 38 | Enabling this gives an improvement in processing time in parts |
| 39 | of the driver, but it may cause problems with EISA (DEFEA) |
| 40 | adapters. TURBOchannel does not have the concept of I/O ports, |
| 41 | so MMIO is always used for these (DEFTA) adapters. |
| 42 | |
| 43 | If unsure, say N. |
| 44 | |
| 45 | config SKFP |
| 46 | tristate "SysKonnect FDDI PCI support" |
| 47 | depends on FDDI && PCI |
| 48 | select BITREVERSE |
| 49 | ---help--- |
| 50 | Say Y here if you have a SysKonnect FDDI PCI adapter. |
| 51 | The following adapters are supported by this driver: |
| 52 | - SK-5521 (SK-NET FDDI-UP) |
| 53 | - SK-5522 (SK-NET FDDI-UP DAS) |
| 54 | - SK-5541 (SK-NET FDDI-FP) |
| 55 | - SK-5543 (SK-NET FDDI-LP) |
| 56 | - SK-5544 (SK-NET FDDI-LP DAS) |
| 57 | - SK-5821 (SK-NET FDDI-UP64) |
| 58 | - SK-5822 (SK-NET FDDI-UP64 DAS) |
| 59 | - SK-5841 (SK-NET FDDI-FP64) |
| 60 | - SK-5843 (SK-NET FDDI-LP64) |
| 61 | - SK-5844 (SK-NET FDDI-LP64 DAS) |
| 62 | - Netelligent 100 FDDI DAS Fibre SC |
| 63 | - Netelligent 100 FDDI SAS Fibre SC |
| 64 | - Netelligent 100 FDDI DAS UTP |
| 65 | - Netelligent 100 FDDI SAS UTP |
| 66 | - Netelligent 100 FDDI SAS Fibre MIC |
| 67 | |
| 68 | Read <file:Documentation/networking/skfp.txt> for information about |
| 69 | the driver. |
| 70 | |
| 71 | Questions concerning this driver can be addressed to: |
| 72 | <linux@syskonnect.de> |
| 73 | |
| 74 | To compile this driver as a module, choose M here: the module |
| 75 | will be called skfp. This is recommended. |
| 76 | |
| 77 | endif # FDDI |