blob: ef6da2df584ba29fbfddcbb19e105d0fe7b1a319 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/* qlogicpti.h: Performance Technologies QlogicISP sbus card defines.
2 *
3 * Copyright (C) 1996 David S. Miller (davem@caipfs.rutgers.edu)
4 */
5
6#ifndef _QLOGICPTI_H
7#define _QLOGICPTI_H
8
9/* Qlogic/SBUS controller registers. */
10#define SBUS_CFG1 0x006UL
11#define SBUS_CTRL 0x008UL
12#define SBUS_STAT 0x00aUL
13#define SBUS_SEMAPHORE 0x00cUL
14#define CMD_DMA_CTRL 0x022UL
15#define DATA_DMA_CTRL 0x042UL
16#define MBOX0 0x080UL
17#define MBOX1 0x082UL
18#define MBOX2 0x084UL
19#define MBOX3 0x086UL
20#define MBOX4 0x088UL
21#define MBOX5 0x08aUL
22#define CPU_CMD 0x214UL
23#define CPU_ORIDE 0x224UL
24#define CPU_PCTRL 0x272UL
25#define CPU_PDIFF 0x276UL
26#define RISC_PSR 0x420UL
27#define RISC_MTREG 0x42EUL
28#define HCCTRL 0x440UL
29
30/* SCSI parameters for this driver. */
31#define MAX_TARGETS 16
32#define MAX_LUNS 8
33
34/* With the qlogic interface, every queue slot can hold a SCSI
35 * command with up to 4 scatter/gather entries. If we need more
36 * than 4 entries, continuation entries can be used that hold
37 * another 7 entries each. Unlike for other drivers, this means
38 * that the maximum number of scatter/gather entries we can
39 * support at any given time is a function of the number of queue
40 * slots available. That is, host->can_queue and host->sg_tablesize
41 * are dynamic and _not_ independent. This all works fine because
42 * requests are queued serially and the scatter/gather limit is
43 * determined for each queue request anew.
44 */
45#define QLOGICPTI_REQ_QUEUE_LEN 255 /* must be power of two - 1 */
46#define QLOGICPTI_MAX_SG(ql) (4 + ((ql) > 0) ? 7*((ql) - 1) : 0)
47
48/* mailbox command complete status codes */
49#define MBOX_COMMAND_COMPLETE 0x4000
50#define INVALID_COMMAND 0x4001
51#define HOST_INTERFACE_ERROR 0x4002
52#define TEST_FAILED 0x4003
53#define COMMAND_ERROR 0x4005
54#define COMMAND_PARAM_ERROR 0x4006
55
56/* async event status codes */
57#define ASYNC_SCSI_BUS_RESET 0x8001
58#define SYSTEM_ERROR 0x8002
59#define REQUEST_TRANSFER_ERROR 0x8003
60#define RESPONSE_TRANSFER_ERROR 0x8004
61#define REQUEST_QUEUE_WAKEUP 0x8005
62#define EXECUTION_TIMEOUT_RESET 0x8006
63
64/* Am I fucking pedantic or what? */
65struct Entry_header {
66#ifdef __BIG_ENDIAN
67 u8 entry_cnt;
68 u8 entry_type;
69 u8 flags;
70 u8 sys_def_1;
71#else /* __LITTLE_ENDIAN */
72 u8 entry_type;
73 u8 entry_cnt;
74 u8 sys_def_1;
75 u8 flags;
76#endif
77};
78
79/* entry header type commands */
80#define ENTRY_COMMAND 1
81#define ENTRY_CONTINUATION 2
82#define ENTRY_STATUS 3
83#define ENTRY_MARKER 4
84#define ENTRY_EXTENDED_COMMAND 5
85
86/* entry header flag definitions */
87#define EFLAG_CONTINUATION 1
88#define EFLAG_BUSY 2
89#define EFLAG_BAD_HEADER 4
90#define EFLAG_BAD_PAYLOAD 8
91
92struct dataseg {
93 u32 d_base;
94 u32 d_count;
95};
96
97struct Command_Entry {
98 struct Entry_header hdr;
99 u32 handle;
100#ifdef __BIG_ENDIAN
101 u8 target_id;
102 u8 target_lun;
103#else /* __LITTLE_ENDIAN */
104 u8 target_lun;
105 u8 target_id;
106#endif
107 u16 cdb_length;
108 u16 control_flags;
109 u16 rsvd;
110 u16 time_out;
111 u16 segment_cnt;
112 u8 cdb[12];
113 struct dataseg dataseg[4];
114};
115
116/* command entry control flag definitions */
117#define CFLAG_NODISC 0x01
118#define CFLAG_HEAD_TAG 0x02
119#define CFLAG_ORDERED_TAG 0x04
120#define CFLAG_SIMPLE_TAG 0x08
121#define CFLAG_TAR_RTN 0x10
122#define CFLAG_READ 0x20
123#define CFLAG_WRITE 0x40
124
125struct Ext_Command_Entry {
126 struct Entry_header hdr;
127 u32 handle;
128#ifdef __BIG_ENDIAN
129 u8 target_id;
130 u8 target_lun;
131#else /* __LITTLE_ENDIAN */
132 u8 target_lun;
133 u8 target_id;
134#endif
135 u16 cdb_length;
136 u16 control_flags;
137 u16 rsvd;
138 u16 time_out;
139 u16 segment_cnt;
140 u8 cdb[44];
141};
142
143struct Continuation_Entry {
144 struct Entry_header hdr;
145 u32 reserved;
146 struct dataseg dataseg[7];
147};
148
149struct Marker_Entry {
150 struct Entry_header hdr;
151 u32 reserved;
152#ifdef __BIG_ENDIAN
153 u8 target_id;
154 u8 target_lun;
155#else /* __LITTLE_ENDIAN */
156 u8 target_lun;
157 u8 target_id;
158#endif
159#ifdef __BIG_ENDIAN
160 u8 rsvd;
161 u8 modifier;
162#else /* __LITTLE_ENDIAN */
163 u8 modifier;
164 u8 rsvd;
165#endif
166 u8 rsvds[52];
167};
168
169/* marker entry modifier definitions */
170#define SYNC_DEVICE 0
171#define SYNC_TARGET 1
172#define SYNC_ALL 2
173
174struct Status_Entry {
175 struct Entry_header hdr;
176 u32 handle;
177 u16 scsi_status;
178 u16 completion_status;
179 u16 state_flags;
180 u16 status_flags;
181 u16 time;
182 u16 req_sense_len;
183 u32 residual;
184 u8 rsvd[8];
185 u8 req_sense_data[32];
186};
187
188/* status entry completion status definitions */
189#define CS_COMPLETE 0x0000
190#define CS_INCOMPLETE 0x0001
191#define CS_DMA_ERROR 0x0002
192#define CS_TRANSPORT_ERROR 0x0003
193#define CS_RESET_OCCURRED 0x0004
194#define CS_ABORTED 0x0005
195#define CS_TIMEOUT 0x0006
196#define CS_DATA_OVERRUN 0x0007
197#define CS_COMMAND_OVERRUN 0x0008
198#define CS_STATUS_OVERRUN 0x0009
199#define CS_BAD_MESSAGE 0x000a
200#define CS_NO_MESSAGE_OUT 0x000b
201#define CS_EXT_ID_FAILED 0x000c
202#define CS_IDE_MSG_FAILED 0x000d
203#define CS_ABORT_MSG_FAILED 0x000e
204#define CS_REJECT_MSG_FAILED 0x000f
205#define CS_NOP_MSG_FAILED 0x0010
206#define CS_PARITY_ERROR_MSG_FAILED 0x0011
207#define CS_DEVICE_RESET_MSG_FAILED 0x0012
208#define CS_ID_MSG_FAILED 0x0013
209#define CS_UNEXP_BUS_FREE 0x0014
210#define CS_DATA_UNDERRUN 0x0015
211#define CS_BUS_RESET 0x001c
212
213/* status entry state flag definitions */
214#define SF_GOT_BUS 0x0100
215#define SF_GOT_TARGET 0x0200
216#define SF_SENT_CDB 0x0400
217#define SF_TRANSFERRED_DATA 0x0800
218#define SF_GOT_STATUS 0x1000
219#define SF_GOT_SENSE 0x2000
220
221/* status entry status flag definitions */
222#define STF_DISCONNECT 0x0001
223#define STF_SYNCHRONOUS 0x0002
224#define STF_PARITY_ERROR 0x0004
225#define STF_BUS_RESET 0x0008
226#define STF_DEVICE_RESET 0x0010
227#define STF_ABORTED 0x0020
228#define STF_TIMEOUT 0x0040
229#define STF_NEGOTIATION 0x0080
230
231/* mailbox commands */
232#define MBOX_NO_OP 0x0000
233#define MBOX_LOAD_RAM 0x0001
234#define MBOX_EXEC_FIRMWARE 0x0002
235#define MBOX_DUMP_RAM 0x0003
236#define MBOX_WRITE_RAM_WORD 0x0004
237#define MBOX_READ_RAM_WORD 0x0005
238#define MBOX_MAILBOX_REG_TEST 0x0006
239#define MBOX_VERIFY_CHECKSUM 0x0007
240#define MBOX_ABOUT_FIRMWARE 0x0008
241#define MBOX_CHECK_FIRMWARE 0x000e
242#define MBOX_INIT_REQ_QUEUE 0x0010
243#define MBOX_INIT_RES_QUEUE 0x0011
244#define MBOX_EXECUTE_IOCB 0x0012
245#define MBOX_WAKE_UP 0x0013
246#define MBOX_STOP_FIRMWARE 0x0014
247#define MBOX_ABORT 0x0015
248#define MBOX_ABORT_DEVICE 0x0016
249#define MBOX_ABORT_TARGET 0x0017
250#define MBOX_BUS_RESET 0x0018
251#define MBOX_STOP_QUEUE 0x0019
252#define MBOX_START_QUEUE 0x001a
253#define MBOX_SINGLE_STEP_QUEUE 0x001b
254#define MBOX_ABORT_QUEUE 0x001c
255#define MBOX_GET_DEV_QUEUE_STATUS 0x001d
256#define MBOX_GET_FIRMWARE_STATUS 0x001f
257#define MBOX_GET_INIT_SCSI_ID 0x0020
258#define MBOX_GET_SELECT_TIMEOUT 0x0021
259#define MBOX_GET_RETRY_COUNT 0x0022
260#define MBOX_GET_TAG_AGE_LIMIT 0x0023
261#define MBOX_GET_CLOCK_RATE 0x0024
262#define MBOX_GET_ACT_NEG_STATE 0x0025
263#define MBOX_GET_ASYNC_DATA_SETUP_TIME 0x0026
264#define MBOX_GET_SBUS_PARAMS 0x0027
265#define MBOX_GET_TARGET_PARAMS 0x0028
266#define MBOX_GET_DEV_QUEUE_PARAMS 0x0029
267#define MBOX_SET_INIT_SCSI_ID 0x0030
268#define MBOX_SET_SELECT_TIMEOUT 0x0031
269#define MBOX_SET_RETRY_COUNT 0x0032
270#define MBOX_SET_TAG_AGE_LIMIT 0x0033
271#define MBOX_SET_CLOCK_RATE 0x0034
272#define MBOX_SET_ACTIVE_NEG_STATE 0x0035
273#define MBOX_SET_ASYNC_DATA_SETUP_TIME 0x0036
274#define MBOX_SET_SBUS_CONTROL_PARAMS 0x0037
275#define MBOX_SET_TARGET_PARAMS 0x0038
276#define MBOX_SET_DEV_QUEUE_PARAMS 0x0039
277
278struct host_param {
279 u_short initiator_scsi_id;
280 u_short bus_reset_delay;
281 u_short retry_count;
282 u_short retry_delay;
283 u_short async_data_setup_time;
284 u_short req_ack_active_negation;
285 u_short data_line_active_negation;
286 u_short data_dma_burst_enable;
287 u_short command_dma_burst_enable;
288 u_short tag_aging;
289 u_short selection_timeout;
290 u_short max_queue_depth;
291};
292
293/*
294 * Device Flags:
295 *
296 * Bit Name
297 * ---------
298 * 7 Disconnect Privilege
299 * 6 Parity Checking
300 * 5 Wide Data Transfers
301 * 4 Synchronous Data Transfers
302 * 3 Tagged Queuing
303 * 2 Automatic Request Sense
304 * 1 Stop Queue on Check Condition
305 * 0 Renegotiate on Error
306 */
307
308struct dev_param {
309 u_short device_flags;
310 u_short execution_throttle;
311 u_short synchronous_period;
312 u_short synchronous_offset;
313 u_short device_enable;
314 u_short reserved; /* pad */
315};
316
317/*
318 * The result queue can be quite a bit smaller since continuation entries
319 * do not show up there:
320 */
321#define RES_QUEUE_LEN 255 /* Must be power of two - 1 */
322#define QUEUE_ENTRY_LEN 64
323
324#define NEXT_REQ_PTR(wheee) (((wheee) + 1) & QLOGICPTI_REQ_QUEUE_LEN)
325#define NEXT_RES_PTR(wheee) (((wheee) + 1) & RES_QUEUE_LEN)
326#define PREV_REQ_PTR(wheee) (((wheee) - 1) & QLOGICPTI_REQ_QUEUE_LEN)
327#define PREV_RES_PTR(wheee) (((wheee) - 1) & RES_QUEUE_LEN)
328
329struct pti_queue_entry {
330 char __opaque[QUEUE_ENTRY_LEN];
331};
332
333struct scsi_cmnd;
334
335/* Software state for the driver. */
336struct qlogicpti {
337 /* These are the hot elements in the cache, so they come first. */
338 void __iomem *qregs; /* Adapter registers */
339 struct pti_queue_entry *res_cpu; /* Ptr to RESPONSE bufs (CPU) */
340 struct pti_queue_entry *req_cpu; /* Ptr to REQUEST bufs (CPU) */
341
342 u_int req_in_ptr; /* index of next request slot */
343 u_int res_out_ptr; /* index of next result slot */
344 long send_marker; /* must we send a marker? */
345 struct sbus_dev *sdev;
346 unsigned long __pad;
347
348 int cmd_count[MAX_TARGETS];
349 unsigned long tag_ages[MAX_TARGETS];
350
351 /* The cmd->handler is only 32-bits, so that things work even on monster
352 * Ex000 sparc64 machines with >4GB of ram we just keep track of the
353 * scsi command pointers here. This is essentially what Matt Jacob does. -DaveM
354 */
355 struct scsi_cmnd *cmd_slots[QLOGICPTI_REQ_QUEUE_LEN + 1];
356
357 /* The rest of the elements are unimportant for performance. */
358 struct qlogicpti *next;
359 __u32 res_dvma; /* Ptr to RESPONSE bufs (DVMA)*/
360 __u32 req_dvma; /* Ptr to REQUEST bufs (DVMA) */
361 u_char fware_majrev, fware_minrev, fware_micrev;
362 struct Scsi_Host *qhost;
363 int qpti_id;
364 int scsi_id;
365 int prom_node;
366 char prom_name[64];
367 int irq;
368 char differential, ultra, clock;
369 unsigned char bursts;
370 struct host_param host_param;
371 struct dev_param dev_param[MAX_TARGETS];
372
373 void __iomem *sreg;
374#define SREG_TPOWER 0x80 /* State of termpwr */
375#define SREG_FUSE 0x40 /* State of on board fuse */
376#define SREG_PDISAB 0x20 /* Disable state for power on */
377#define SREG_DSENSE 0x10 /* Sense for differential */
378#define SREG_IMASK 0x0c /* Interrupt level */
379#define SREG_SPMASK 0x03 /* Mask for switch pack */
380 unsigned char swsreg;
381 unsigned int
382 gotirq : 1, /* this instance got an irq */
Matthew Wilcox9ec76fb2007-10-01 08:07:52 -0600383 is_pti : 1; /* Non-zero if this is a PTI board. */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700384};
385
386/* How to twiddle them bits... */
387
388/* SBUS config register one. */
389#define SBUS_CFG1_EPAR 0x0100 /* Enable parity checking */
390#define SBUS_CFG1_FMASK 0x00f0 /* Forth code cycle mask */
391#define SBUS_CFG1_BENAB 0x0004 /* Burst dvma enable */
392#define SBUS_CFG1_B64 0x0003 /* Enable 64byte bursts */
393#define SBUS_CFG1_B32 0x0002 /* Enable 32byte bursts */
394#define SBUS_CFG1_B16 0x0001 /* Enable 16byte bursts */
395#define SBUS_CFG1_B8 0x0008 /* Enable 8byte bursts */
396
397/* SBUS control register */
398#define SBUS_CTRL_EDIRQ 0x0020 /* Enable Data DVMA Interrupts */
399#define SBUS_CTRL_ECIRQ 0x0010 /* Enable Command DVMA Interrupts */
400#define SBUS_CTRL_ESIRQ 0x0008 /* Enable SCSI Processor Interrupts */
401#define SBUS_CTRL_ERIRQ 0x0004 /* Enable RISC Processor Interrupts */
402#define SBUS_CTRL_GENAB 0x0002 /* Global Interrupt Enable */
403#define SBUS_CTRL_RESET 0x0001 /* Soft Reset */
404
405/* SBUS status register */
406#define SBUS_STAT_DINT 0x0020 /* Data DVMA IRQ pending */
407#define SBUS_STAT_CINT 0x0010 /* Command DVMA IRQ pending */
408#define SBUS_STAT_SINT 0x0008 /* SCSI Processor IRQ pending */
409#define SBUS_STAT_RINT 0x0004 /* RISC Processor IRQ pending */
410#define SBUS_STAT_GINT 0x0002 /* Global IRQ pending */
411
412/* SBUS semaphore register */
413#define SBUS_SEMAPHORE_STAT 0x0002 /* Semaphore status bit */
414#define SBUS_SEMAPHORE_LCK 0x0001 /* Semaphore lock bit */
415
416/* DVMA control register */
417#define DMA_CTRL_CSUSPEND 0x0010 /* DMA channel suspend */
418#define DMA_CTRL_CCLEAR 0x0008 /* DMA channel clear and reset */
419#define DMA_CTRL_FCLEAR 0x0004 /* DMA fifo clear */
420#define DMA_CTRL_CIRQ 0x0002 /* DMA irq clear */
421#define DMA_CTRL_DMASTART 0x0001 /* DMA transfer start */
422
423/* SCSI processor override register */
424#define CPU_ORIDE_ETRIG 0x8000 /* External trigger enable */
425#define CPU_ORIDE_STEP 0x4000 /* Single step mode enable */
426#define CPU_ORIDE_BKPT 0x2000 /* Breakpoint reg enable */
427#define CPU_ORIDE_PWRITE 0x1000 /* SCSI pin write enable */
428#define CPU_ORIDE_OFORCE 0x0800 /* Force outputs on */
429#define CPU_ORIDE_LBACK 0x0400 /* SCSI loopback enable */
430#define CPU_ORIDE_PTEST 0x0200 /* Parity test enable */
431#define CPU_ORIDE_TENAB 0x0100 /* SCSI pins tristate enable */
432#define CPU_ORIDE_TPINS 0x0080 /* SCSI pins enable */
433#define CPU_ORIDE_FRESET 0x0008 /* FIFO reset */
434#define CPU_ORIDE_CTERM 0x0004 /* Command terminate */
435#define CPU_ORIDE_RREG 0x0002 /* Reset SCSI processor regs */
436#define CPU_ORIDE_RMOD 0x0001 /* Reset SCSI processor module */
437
438/* SCSI processor commands */
439#define CPU_CMD_BRESET 0x300b /* Reset SCSI bus */
440
441/* SCSI processor pin control register */
442#define CPU_PCTRL_PVALID 0x8000 /* Phase bits are valid */
443#define CPU_PCTRL_PHI 0x0400 /* Parity bit high */
444#define CPU_PCTRL_PLO 0x0200 /* Parity bit low */
445#define CPU_PCTRL_REQ 0x0100 /* REQ bus signal */
446#define CPU_PCTRL_ACK 0x0080 /* ACK bus signal */
447#define CPU_PCTRL_RST 0x0040 /* RST bus signal */
448#define CPU_PCTRL_BSY 0x0020 /* BSY bus signal */
449#define CPU_PCTRL_SEL 0x0010 /* SEL bus signal */
450#define CPU_PCTRL_ATN 0x0008 /* ATN bus signal */
451#define CPU_PCTRL_MSG 0x0004 /* MSG bus signal */
452#define CPU_PCTRL_CD 0x0002 /* CD bus signal */
453#define CPU_PCTRL_IO 0x0001 /* IO bus signal */
454
455/* SCSI processor differential pins register */
456#define CPU_PDIFF_SENSE 0x0200 /* Differential sense */
457#define CPU_PDIFF_MODE 0x0100 /* Differential mode */
458#define CPU_PDIFF_OENAB 0x0080 /* Outputs enable */
459#define CPU_PDIFF_PMASK 0x007c /* Differential control pins */
460#define CPU_PDIFF_TGT 0x0002 /* Target mode enable */
461#define CPU_PDIFF_INIT 0x0001 /* Initiator mode enable */
462
463/* RISC processor status register */
464#define RISC_PSR_FTRUE 0x8000 /* Force true */
465#define RISC_PSR_LCD 0x4000 /* Loop counter shows done status */
466#define RISC_PSR_RIRQ 0x2000 /* RISC irq status */
467#define RISC_PSR_TOFLOW 0x1000 /* Timer overflow (rollover) */
468#define RISC_PSR_AOFLOW 0x0800 /* Arithmetic overflow */
469#define RISC_PSR_AMSB 0x0400 /* Arithmetic big endian */
470#define RISC_PSR_ACARRY 0x0200 /* Arithmetic carry */
471#define RISC_PSR_AZERO 0x0100 /* Arithmetic zero */
472#define RISC_PSR_ULTRA 0x0020 /* Ultra mode */
473#define RISC_PSR_DIRQ 0x0010 /* DVMA interrupt */
474#define RISC_PSR_SIRQ 0x0008 /* SCSI processor interrupt */
475#define RISC_PSR_HIRQ 0x0004 /* Host interrupt */
476#define RISC_PSR_IPEND 0x0002 /* Interrupt pending */
477#define RISC_PSR_FFALSE 0x0001 /* Force false */
478
479/* RISC processor memory timing register */
480#define RISC_MTREG_P1DFLT 0x1200 /* Default read/write timing, pg1 */
481#define RISC_MTREG_P0DFLT 0x0012 /* Default read/write timing, pg0 */
482#define RISC_MTREG_P1ULTRA 0x2300 /* Ultra-mode rw timing, pg1 */
483#define RISC_MTREG_P0ULTRA 0x0023 /* Ultra-mode rw timing, pg0 */
484
485/* Host command/ctrl register */
486#define HCCTRL_NOP 0x0000 /* CMD: No operation */
487#define HCCTRL_RESET 0x1000 /* CMD: Reset RISC cpu */
488#define HCCTRL_PAUSE 0x2000 /* CMD: Pause RISC cpu */
489#define HCCTRL_REL 0x3000 /* CMD: Release paused RISC cpu */
490#define HCCTRL_STEP 0x4000 /* CMD: Single step RISC cpu */
491#define HCCTRL_SHIRQ 0x5000 /* CMD: Set host irq */
492#define HCCTRL_CHIRQ 0x6000 /* CMD: Clear host irq */
493#define HCCTRL_CRIRQ 0x7000 /* CMD: Clear RISC cpu irq */
494#define HCCTRL_BKPT 0x8000 /* CMD: Breakpoint enables change */
495#define HCCTRL_TMODE 0xf000 /* CMD: Enable test mode */
496#define HCCTRL_HIRQ 0x0080 /* Host IRQ pending */
497#define HCCTRL_RRIP 0x0040 /* RISC cpu reset in happening now */
498#define HCCTRL_RPAUSED 0x0020 /* RISC cpu is paused now */
499#define HCCTRL_EBENAB 0x0010 /* External breakpoint enable */
500#define HCCTRL_B1ENAB 0x0008 /* Breakpoint 1 enable */
501#define HCCTRL_B0ENAB 0x0004 /* Breakpoint 0 enable */
502
503/* For our interrupt engine. */
504#define for_each_qlogicpti(qp) \
505 for((qp) = qptichain; (qp); (qp) = (qp)->next)
506
507#endif /* !(_QLOGICPTI_H) */