blob: 8a1097cf8a83b78a3dea7a3b64485ab752cfc946 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 lne390.c
3
4 Linux driver for Mylex LNE390 EISA Network Adapter
5
6 Copyright (C) 1996-1998, Paul Gortmaker.
7
8 This software may be used and distributed according to the terms
9 of the GNU General Public License, incorporated herein by reference.
10
11 Information and Code Sources:
12
13 1) Based upon framework of es3210 driver.
14 2) The existing myriad of other Linux 8390 drivers by Donald Becker.
15 3) Russ Nelson's asm packet driver provided additional info.
16 4) Info for getting IRQ and sh-mem gleaned from the EISA cfg files.
17
18 The LNE390 is an EISA shared memory NS8390 implementation. Note
19 that all memory copies to/from the board must be 32bit transfers.
20 There are two versions of the card: the lne390a and the lne390b.
21 Going by the EISA cfg files, the "a" has jumpers to select between
22 BNC/AUI, but the "b" also has RJ-45 and selection is via the SCU.
23 The shared memory address selection is also slightly different.
24 Note that shared memory address > 1MB are supported with this driver.
25
26 You can try <http://www.mylex.com> if you want more info, as I've
27 never even seen one of these cards. :)
28
29 Arnaldo Carvalho de Melo <acme@conectiva.com.br> - 2000/09/01
30 - get rid of check_region
31 - no need to check if dev == NULL in lne390_probe1
32*/
33
34static const char *version =
35 "lne390.c: Driver revision v0.99.1, 01/09/2000\n";
36
37#include <linux/module.h>
38#include <linux/eisa.h>
39#include <linux/kernel.h>
40#include <linux/errno.h>
41#include <linux/string.h>
42#include <linux/delay.h>
43#include <linux/init.h>
44#include <linux/netdevice.h>
45#include <linux/etherdevice.h>
46
47#include <asm/io.h>
48#include <asm/system.h>
49
50#include "8390.h"
51
52#define DRV_NAME "lne390"
53
54static int lne390_probe1(struct net_device *dev, int ioaddr);
55
Linus Torvalds1da177e2005-04-16 15:20:36 -070056static void lne390_reset_8390(struct net_device *dev);
57
58static void lne390_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page);
59static void lne390_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset);
60static void lne390_block_output(struct net_device *dev, int count, const unsigned char *buf, const int start_page);
61
62#define LNE390_START_PG 0x00 /* First page of TX buffer */
63#define LNE390_STOP_PG 0x80 /* Last page +1 of RX ring */
64
65#define LNE390_ID_PORT 0xc80 /* Same for all EISA cards */
66#define LNE390_IO_EXTENT 0x20
67#define LNE390_SA_PROM 0x16 /* Start of e'net addr. */
68#define LNE390_RESET_PORT 0xc84 /* From the pkt driver source */
69#define LNE390_NIC_OFFSET 0x00 /* Hello, the 8390 is *here* */
70
71#define LNE390_ADDR0 0x00 /* 3 byte vendor prefix */
72#define LNE390_ADDR1 0x80
73#define LNE390_ADDR2 0xe5
74
75#define LNE390_ID0 0x10009835 /* 0x3598 = 01101 01100 11000 = mlx */
76#define LNE390_ID1 0x11009835 /* above is the 390A, this is 390B */
77
78#define LNE390_CFG1 0xc84 /* NB: 0xc84 is also "reset" port. */
79#define LNE390_CFG2 0xc90
80
81/*
82 * You can OR any of the following bits together and assign it
83 * to LNE390_DEBUG to get verbose driver info during operation.
84 * Currently only the probe one is implemented.
85 */
86
87#define LNE390_D_PROBE 0x01
88#define LNE390_D_RX_PKT 0x02
89#define LNE390_D_TX_PKT 0x04
90#define LNE390_D_IRQ 0x08
91
92#define LNE390_DEBUG 0
93
94static unsigned char irq_map[] __initdata = {15, 12, 11, 10, 9, 7, 5, 3};
95static unsigned int shmem_mapA[] __initdata = {0xff, 0xfe, 0xfd, 0xfff, 0xffe, 0xffc, 0x0d, 0x0};
96static unsigned int shmem_mapB[] __initdata = {0xff, 0xfe, 0x0e, 0xfff, 0xffe, 0xffc, 0x0d, 0x0};
97
98/*
99 * Probe for the card. The best way is to read the EISA ID if it
100 * is known. Then we can check the prefix of the station address
101 * PROM for a match against the value assigned to Mylex.
102 */
103
104static int __init do_lne390_probe(struct net_device *dev)
105{
106 unsigned short ioaddr = dev->base_addr;
107 int irq = dev->irq;
108 int mem_start = dev->mem_start;
109 int ret;
110
Linus Torvalds1da177e2005-04-16 15:20:36 -0700111 if (ioaddr > 0x1ff) { /* Check a single specified location. */
112 if (!request_region(ioaddr, LNE390_IO_EXTENT, DRV_NAME))
113 return -EBUSY;
114 ret = lne390_probe1(dev, ioaddr);
115 if (ret)
116 release_region(ioaddr, LNE390_IO_EXTENT);
117 return ret;
118 }
119 else if (ioaddr > 0) /* Don't probe at all. */
120 return -ENXIO;
121
122 if (!EISA_bus) {
123#if LNE390_DEBUG & LNE390_D_PROBE
124 printk("lne390-debug: Not an EISA bus. Not probing high ports.\n");
125#endif
126 return -ENXIO;
127 }
128
129 /* EISA spec allows for up to 16 slots, but 8 is typical. */
130 for (ioaddr = 0x1000; ioaddr < 0x9000; ioaddr += 0x1000) {
131 if (!request_region(ioaddr, LNE390_IO_EXTENT, DRV_NAME))
132 continue;
133 if (lne390_probe1(dev, ioaddr) == 0)
134 return 0;
135 release_region(ioaddr, LNE390_IO_EXTENT);
136 dev->irq = irq;
137 dev->mem_start = mem_start;
138 }
139
140 return -ENODEV;
141}
142
Linus Torvalds1da177e2005-04-16 15:20:36 -0700143#ifndef MODULE
144struct net_device * __init lne390_probe(int unit)
145{
146 struct net_device *dev = alloc_ei_netdev();
147 int err;
148
149 if (!dev)
150 return ERR_PTR(-ENOMEM);
151
152 sprintf(dev->name, "eth%d", unit);
153 netdev_boot_setup_check(dev);
154
155 err = do_lne390_probe(dev);
156 if (err)
157 goto out;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700158 return dev;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700159out:
160 free_netdev(dev);
161 return ERR_PTR(err);
162}
163#endif
164
165static int __init lne390_probe1(struct net_device *dev, int ioaddr)
166{
167 int i, revision, ret;
168 unsigned long eisa_id;
169
170 if (inb_p(ioaddr + LNE390_ID_PORT) == 0xff) return -ENODEV;
171
172#if LNE390_DEBUG & LNE390_D_PROBE
173 printk("lne390-debug: probe at %#x, ID %#8x\n", ioaddr, inl(ioaddr + LNE390_ID_PORT));
174 printk("lne390-debug: config regs: %#x %#x\n",
175 inb(ioaddr + LNE390_CFG1), inb(ioaddr + LNE390_CFG2));
176#endif
177
178
179/* Check the EISA ID of the card. */
180 eisa_id = inl(ioaddr + LNE390_ID_PORT);
181 if ((eisa_id != LNE390_ID0) && (eisa_id != LNE390_ID1)) {
182 return -ENODEV;
183 }
184
185 revision = (eisa_id >> 24) & 0x01; /* 0 = rev A, 1 rev B */
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400186
Linus Torvalds1da177e2005-04-16 15:20:36 -0700187#if 0
188/* Check the Mylex vendor ID as well. Not really required. */
189 if (inb(ioaddr + LNE390_SA_PROM + 0) != LNE390_ADDR0
190 || inb(ioaddr + LNE390_SA_PROM + 1) != LNE390_ADDR1
191 || inb(ioaddr + LNE390_SA_PROM + 2) != LNE390_ADDR2 ) {
192 printk("lne390.c: card not found");
193 for(i = 0; i < ETHER_ADDR_LEN; i++)
194 printk(" %02x", inb(ioaddr + LNE390_SA_PROM + i));
195 printk(" (invalid prefix).\n");
196 return -ENODEV;
197 }
198#endif
199
Linus Torvalds1da177e2005-04-16 15:20:36 -0700200 for(i = 0; i < ETHER_ADDR_LEN; i++)
Joe Perches0795af52007-10-03 17:59:30 -0700201 dev->dev_addr[i] = inb(ioaddr + LNE390_SA_PROM + i);
Johannes Berge1749612008-10-27 15:59:26 -0700202 printk("lne390.c: LNE390%X in EISA slot %d, address %pM.\n",
203 0xa+revision, ioaddr/0x1000, dev->dev_addr);
Joe Perches0795af52007-10-03 17:59:30 -0700204
205 printk("lne390.c: ");
Linus Torvalds1da177e2005-04-16 15:20:36 -0700206
207 /* Snarf the interrupt now. CFG file has them all listed as `edge' with share=NO */
208 if (dev->irq == 0) {
209 unsigned char irq_reg = inb(ioaddr + LNE390_CFG2) >> 3;
210 dev->irq = irq_map[irq_reg & 0x07];
211 printk("using");
212 } else {
213 /* This is useless unless we reprogram the card here too */
214 if (dev->irq == 2) dev->irq = 9; /* Doh! */
215 printk("assigning");
216 }
217 printk(" IRQ %d,", dev->irq);
218
219 if ((ret = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev))) {
220 printk (" unable to get IRQ %d.\n", dev->irq);
221 return ret;
222 }
223
224 if (dev->mem_start == 0) {
225 unsigned char mem_reg = inb(ioaddr + LNE390_CFG2) & 0x07;
226
227 if (revision) /* LNE390B */
228 dev->mem_start = shmem_mapB[mem_reg] * 0x10000;
229 else /* LNE390A */
230 dev->mem_start = shmem_mapA[mem_reg] * 0x10000;
231 printk(" using ");
232 } else {
233 /* Should check for value in shmem_map and reprogram the card to use it */
234 dev->mem_start &= 0xfff0000;
235 printk(" assigning ");
236 }
237
238 printk("%dkB memory at physical address %#lx\n",
239 LNE390_STOP_PG/4, dev->mem_start);
240
241 /*
242 BEWARE!! Some dain-bramaged EISA SCUs will allow you to put
243 the card mem within the region covered by `normal' RAM !!!
244
245 ioremap() will fail in that case.
246 */
247 ei_status.mem = ioremap(dev->mem_start, LNE390_STOP_PG*0x100);
248 if (!ei_status.mem) {
249 printk(KERN_ERR "lne390.c: Unable to remap card memory above 1MB !!\n");
250 printk(KERN_ERR "lne390.c: Try using EISA SCU to set memory below 1MB.\n");
251 printk(KERN_ERR "lne390.c: Driver NOT installed.\n");
252 ret = -EAGAIN;
253 goto cleanup;
254 }
255 printk("lne390.c: remapped %dkB card memory to virtual address %p\n",
256 LNE390_STOP_PG/4, ei_status.mem);
257
258 dev->mem_start = (unsigned long)ei_status.mem;
259 dev->mem_end = dev->mem_start + (LNE390_STOP_PG - LNE390_START_PG)*256;
260
261 /* The 8390 offset is zero for the LNE390 */
262 dev->base_addr = ioaddr;
263
264 ei_status.name = "LNE390";
265 ei_status.tx_start_page = LNE390_START_PG;
266 ei_status.rx_start_page = LNE390_START_PG + TX_PAGES;
267 ei_status.stop_page = LNE390_STOP_PG;
268 ei_status.word16 = 1;
269
270 if (ei_debug > 0)
271 printk(version);
272
273 ei_status.reset_8390 = &lne390_reset_8390;
274 ei_status.block_input = &lne390_block_input;
275 ei_status.block_output = &lne390_block_output;
276 ei_status.get_8390_hdr = &lne390_get_8390_hdr;
277
Stephen Hemminger0ec4d4f2008-11-25 18:24:38 -0800278 dev->netdev_ops = &ei_netdev_ops;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700279 NS8390_init(dev, 0);
b1fc5502005-05-12 20:11:55 -0400280
281 ret = register_netdev(dev);
282 if (ret)
283 goto unmap;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700284 return 0;
b1fc5502005-05-12 20:11:55 -0400285unmap:
286 if (ei_status.reg0)
viro@ZenIV.linux.org.uk387d8902005-09-09 17:22:14 +0100287 iounmap(ei_status.mem);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700288cleanup:
289 free_irq(dev->irq, dev);
290 return ret;
291}
292
293/*
294 * Reset as per the packet driver method. Judging by the EISA cfg
295 * file, this just toggles the "Board Enable" bits (bit 2 and 0).
296 */
297
298static void lne390_reset_8390(struct net_device *dev)
299{
300 unsigned short ioaddr = dev->base_addr;
301
302 outb(0x04, ioaddr + LNE390_RESET_PORT);
303 if (ei_debug > 1) printk("%s: resetting the LNE390...", dev->name);
304
305 mdelay(2);
306
307 ei_status.txing = 0;
308 outb(0x01, ioaddr + LNE390_RESET_PORT);
309 if (ei_debug > 1) printk("reset done\n");
Linus Torvalds1da177e2005-04-16 15:20:36 -0700310}
311
312/*
313 * Note: In the following three functions is the implicit assumption
314 * that the associated memcpy will only use "rep; movsl" as long as
315 * we keep the counts as some multiple of doublewords. This is a
316 * requirement of the hardware, and also prevents us from using
317 * eth_io_copy_and_sum() since we can't guarantee it will limit
318 * itself to doubleword access.
319 */
320
321/*
322 * Grab the 8390 specific header. Similar to the block_input routine, but
323 * we don't need to be concerned with ring wrap as the header will be at
324 * the start of a page, so we optimize accordingly. (A single doubleword.)
325 */
326
327static void
328lne390_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
329{
330 void __iomem *hdr_start = ei_status.mem + ((ring_page - LNE390_START_PG)<<8);
331 memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
332 hdr->count = (hdr->count + 3) & ~3; /* Round up allocation. */
333}
334
Jeff Garzik6aa20a22006-09-13 13:24:59 -0400335/*
Linus Torvalds1da177e2005-04-16 15:20:36 -0700336 * Block input and output are easy on shared memory ethercards, the only
337 * complication is when the ring buffer wraps. The count will already
338 * be rounded up to a doubleword value via lne390_get_8390_hdr() above.
339 */
340
341static void lne390_block_input(struct net_device *dev, int count, struct sk_buff *skb,
342 int ring_offset)
343{
344 void __iomem *xfer_start = ei_status.mem + ring_offset - (LNE390_START_PG<<8);
345
346 if (ring_offset + count > (LNE390_STOP_PG<<8)) {
347 /* Packet wraps over end of ring buffer. */
348 int semi_count = (LNE390_STOP_PG<<8) - ring_offset;
349 memcpy_fromio(skb->data, xfer_start, semi_count);
350 count -= semi_count;
351 memcpy_fromio(skb->data + semi_count,
352 ei_status.mem + (TX_PAGES<<8), count);
353 } else {
354 /* Packet is in one chunk. */
355 memcpy_fromio(skb->data, xfer_start, count);
356 }
357}
358
359static void lne390_block_output(struct net_device *dev, int count,
360 const unsigned char *buf, int start_page)
361{
362 void __iomem *shmem = ei_status.mem + ((start_page - LNE390_START_PG)<<8);
363
364 count = (count + 3) & ~3; /* Round up to doubleword */
365 memcpy_toio(shmem, buf, count);
366}
367
Linus Torvalds1da177e2005-04-16 15:20:36 -0700368
369#ifdef MODULE
370#define MAX_LNE_CARDS 4 /* Max number of LNE390 cards per module */
371static struct net_device *dev_lne[MAX_LNE_CARDS];
372static int io[MAX_LNE_CARDS];
373static int irq[MAX_LNE_CARDS];
374static int mem[MAX_LNE_CARDS];
375
376module_param_array(io, int, NULL, 0);
377module_param_array(irq, int, NULL, 0);
378module_param_array(mem, int, NULL, 0);
379MODULE_PARM_DESC(io, "I/O base address(es)");
380MODULE_PARM_DESC(irq, "IRQ number(s)");
381MODULE_PARM_DESC(mem, "memory base address(es)");
382MODULE_DESCRIPTION("Mylex LNE390A/B EISA Ethernet driver");
383MODULE_LICENSE("GPL");
384
Andrew Mortondab3d022006-08-14 23:00:04 -0700385int __init init_module(void)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700386{
387 struct net_device *dev;
388 int this_dev, found = 0;
389
390 for (this_dev = 0; this_dev < MAX_LNE_CARDS; this_dev++) {
391 if (io[this_dev] == 0 && this_dev != 0)
392 break;
393 dev = alloc_ei_netdev();
394 if (!dev)
395 break;
396 dev->irq = irq[this_dev];
397 dev->base_addr = io[this_dev];
398 dev->mem_start = mem[this_dev];
399 if (do_lne390_probe(dev) == 0) {
b1fc5502005-05-12 20:11:55 -0400400 dev_lne[found++] = dev;
401 continue;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700402 }
403 free_netdev(dev);
404 printk(KERN_WARNING "lne390.c: No LNE390 card found (i/o = 0x%x).\n", io[this_dev]);
405 break;
406 }
407 if (found)
408 return 0;
409 return -ENXIO;
410}
411
Denis Vlasenko64916f12006-01-05 22:45:47 -0800412static void cleanup_card(struct net_device *dev)
413{
414 free_irq(dev->irq, dev);
415 release_region(dev->base_addr, LNE390_IO_EXTENT);
416 iounmap(ei_status.mem);
417}
418
Al Viroafc8eb42006-06-14 18:50:53 -0400419void __exit cleanup_module(void)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700420{
421 int this_dev;
422
423 for (this_dev = 0; this_dev < MAX_LNE_CARDS; this_dev++) {
424 struct net_device *dev = dev_lne[this_dev];
425 if (dev) {
426 unregister_netdev(dev);
427 cleanup_card(dev);
428 free_netdev(dev);
429 }
430 }
431}
432#endif /* MODULE */
433