arch/arm/mach-omap2/board-overo.c

/*
 * board-overo.c (Gumstix Overo)
 *
 * Initial code: Steve Sakoman <steve@sakoman.com>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but
 * WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
 * General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
 * 02110-1301 USA
 *
 */

#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/spi/spi.h>

#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mmc/host.h>

#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>

#include <plat/board.h>
#include <plat/common.h>
#include <video/omapdss.h>
#include <video/omap-panel-generic-dpi.h>
#include <video/omap-panel-dvi.h>
#include <plat/gpmc.h>
#include <mach/hardware.h>
#include <plat/nand.h>
#include <plat/mcspi.h>
#include <plat/mux.h>
#include <plat/usb.h>

#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
#include "common-board-devices.h"

#define OVERO_GPIO_BT_XGATE	15
#define OVERO_GPIO_W2W_NRESET	16
#define OVERO_GPIO_PENDOWN	114
#define OVERO_GPIO_BT_NRESET	164
#define OVERO_GPIO_USBH_CPEN	168
#define OVERO_GPIO_USBH_NRESET	183

#define OVERO_SMSC911X_CS      5
#define OVERO_SMSC911X_GPIO    176
#define OVERO_SMSC911X2_CS     4
#define OVERO_SMSC911X2_GPIO   65

#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
	defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)

/* fixed regulator for ads7846 */
static struct regulator_consumer_supply ads7846_supply[] = {
	REGULATOR_SUPPLY("vcc", "spi1.0"),
};

static struct regulator_init_data vads7846_regulator = {
	.constraints = {
		.valid_ops_mask		= REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= ARRAY_SIZE(ads7846_supply),
	.consumer_supplies	= ads7846_supply,
};

static struct fixed_voltage_config vads7846 = {
	.supply_name		= "vads7846",
	.microvolts		= 3300000, /* 3.3V */
	.gpio			= -EINVAL,
	.startup_delay		= 0,
	.init_data		= &vads7846_regulator,
};

static struct platform_device vads7846_device = {
	.name		= "reg-fixed-voltage",
	.id		= 1,
	.dev = {
		.platform_data = &vads7846,
	},
};

static void __init overo_ads7846_init(void)
{
	omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL);
	platform_device_register(&vads7846_device);
}

#else
static inline void __init overo_ads7846_init(void) { return; }
#endif

#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)

#include <linux/smsc911x.h>
#include <plat/gpmc-smsc911x.h>

static struct omap_smsc911x_platform_data smsc911x_cfg = {
	.id		= 0,
	.cs             = OVERO_SMSC911X_CS,
	.gpio_irq       = OVERO_SMSC911X_GPIO,
	.gpio_reset     = -EINVAL,
	.flags		= SMSC911X_USE_32BIT,
};

static struct omap_smsc911x_platform_data smsc911x2_cfg = {
	.id		= 1,
	.cs             = OVERO_SMSC911X2_CS,
	.gpio_irq       = OVERO_SMSC911X2_GPIO,
	.gpio_reset     = -EINVAL,
	.flags		= SMSC911X_USE_32BIT,
};

static void __init overo_init_smsc911x(void)
{
	gpmc_smsc911x_init(&smsc911x_cfg);
	gpmc_smsc911x_init(&smsc911x2_cfg);
}

#else
static inline void __init overo_init_smsc911x(void) { return; }
#endif

/* DSS */
static int lcd_enabled;
static int dvi_enabled;

#define OVERO_GPIO_LCD_EN 144
#define OVERO_GPIO_LCD_BL 145

static struct gpio overo_dss_gpios[] __initdata = {
	{ OVERO_GPIO_LCD_EN, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_EN" },
	{ OVERO_GPIO_LCD_BL, GPIOF_OUT_INIT_HIGH, "OVERO_GPIO_LCD_BL" },
};

static void __init overo_display_init(void)
{
	if (gpio_request_array(overo_dss_gpios, ARRAY_SIZE(overo_dss_gpios))) {
		printk(KERN_ERR "could not obtain DSS control GPIOs\n");
		return;
	}

	gpio_export(OVERO_GPIO_LCD_EN, 0);
	gpio_export(OVERO_GPIO_LCD_BL, 0);
}

static int overo_panel_enable_dvi(struct omap_dss_device *dssdev)
{
	if (lcd_enabled) {
		printk(KERN_ERR "cannot enable DVI, LCD is enabled\n");
		return -EINVAL;
	}
	dvi_enabled = 1;

	return 0;
}

static void overo_panel_disable_dvi(struct omap_dss_device *dssdev)
{
	dvi_enabled = 0;
}

static struct panel_dvi_platform_data dvi_panel = {
	.platform_enable	= overo_panel_enable_dvi,
	.platform_disable	= overo_panel_disable_dvi,
};

static struct omap_dss_device overo_dvi_device = {
	.name			= "dvi",
	.type			= OMAP_DISPLAY_TYPE_DPI,
	.driver_name		= "dvi",
	.data			= &dvi_panel,
	.phy.dpi.data_lines	= 24,
};

static struct omap_dss_device overo_tv_device = {
	.name = "tv",
	.driver_name = "venc",
	.type = OMAP_DISPLAY_TYPE_VENC,
	.phy.venc.type = OMAP_DSS_VENC_TYPE_SVIDEO,
};

static int overo_panel_enable_lcd(struct omap_dss_device *dssdev)
{
	if (dvi_enabled) {
		printk(KERN_ERR "cannot enable LCD, DVI is enabled\n");
		return -EINVAL;
	}

	gpio_set_value(OVERO_GPIO_LCD_EN, 1);
	gpio_set_value(OVERO_GPIO_LCD_BL, 1);
	lcd_enabled = 1;
	return 0;
}

static void overo_panel_disable_lcd(struct omap_dss_device *dssdev)
{
	gpio_set_value(OVERO_GPIO_LCD_EN, 0);
	gpio_set_value(OVERO_GPIO_LCD_BL, 0);
	lcd_enabled = 0;
}

static struct panel_generic_dpi_data lcd43_panel = {
	.name			= "samsung_lte430wq_f0c",
	.platform_enable	= overo_panel_enable_lcd,
	.platform_disable	= overo_panel_disable_lcd,
};

static struct omap_dss_device overo_lcd43_device = {
	.name			= "lcd43",
	.type			= OMAP_DISPLAY_TYPE_DPI,
	.driver_name		= "generic_dpi_panel",
	.data			= &lcd43_panel,
	.phy.dpi.data_lines	= 24,
};

#if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \
	defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE)
static struct omap_dss_device overo_lcd35_device = {
	.type			= OMAP_DISPLAY_TYPE_DPI,
	.name			= "lcd35",
	.driver_name		= "lgphilips_lb035q02_panel",
	.phy.dpi.data_lines	= 24,
	.platform_enable	= overo_panel_enable_lcd,
	.platform_disable	= overo_panel_disable_lcd,
};
#endif

static struct omap_dss_device *overo_dss_devices[] = {
	&overo_dvi_device,
	&overo_tv_device,
#if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \
	defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE)
	&overo_lcd35_device,
#endif
	&overo_lcd43_device,
};

static struct omap_dss_board_info overo_dss_data = {
	.num_devices	= ARRAY_SIZE(overo_dss_devices),
	.devices	= overo_dss_devices,
	.default_device	= &overo_dvi_device,
};

static struct mtd_partition overo_nand_partitions[] = {
	{
		.name           = "xloader",
		.offset         = 0,			/* Offset = 0x00000 */
		.size           = 4 * NAND_BLOCK_SIZE,
		.mask_flags     = MTD_WRITEABLE
	},
	{
		.name           = "uboot",
		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x80000 */
		.size           = 14 * NAND_BLOCK_SIZE,
	},
	{
		.name           = "uboot environment",
		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x240000 */
		.size           = 2 * NAND_BLOCK_SIZE,
	},
	{
		.name           = "linux",
		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x280000 */
		.size           = 32 * NAND_BLOCK_SIZE,
	},
	{
		.name           = "rootfs",
		.offset         = MTDPART_OFS_APPEND,	/* Offset = 0x680000 */
		.size           = MTDPART_SIZ_FULL,
	},
};

static struct omap2_hsmmc_info mmc[] = {
	{
		.mmc		= 1,
		.caps		= MMC_CAP_4_BIT_DATA,
		.gpio_cd	= -EINVAL,
		.gpio_wp	= -EINVAL,
	},
	{
		.mmc		= 2,
		.caps		= MMC_CAP_4_BIT_DATA,
		.gpio_cd	= -EINVAL,
		.gpio_wp	= -EINVAL,
		.transceiver	= true,
		.ocr_mask	= 0x00100000,	/* 3.3V */
	},
	{}	/* Terminator */
};

static struct regulator_consumer_supply overo_vmmc1_supply[] = {
	REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};

#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>

static struct gpio_led gpio_leds[] = {
	{
		.name			= "overo:red:gpio21",
		.default_trigger	= "heartbeat",
		.gpio			= 21,
		.active_low		= true,
	},
	{
		.name			= "overo:blue:gpio22",
		.default_trigger	= "none",
		.gpio			= 22,
		.active_low		= true,
	},
	{
		.name			= "overo:blue:COM",
		.default_trigger	= "mmc0",
		.gpio			= -EINVAL,	/* gets replaced */
		.active_low		= true,
	},
};

static struct gpio_led_platform_data gpio_leds_pdata = {
	.leds		= gpio_leds,
	.num_leds	= ARRAY_SIZE(gpio_leds),
};

static struct platform_device gpio_leds_device = {
	.name	= "leds-gpio",
	.id	= -1,
	.dev	= {
		.platform_data	= &gpio_leds_pdata,
	},
};

static void __init overo_init_led(void)
{
	platform_device_register(&gpio_leds_device);
}

#else
static inline void __init overo_init_led(void) { return; }
#endif

#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
#include <linux/input.h>
#include <linux/gpio_keys.h>

static struct gpio_keys_button gpio_buttons[] = {
	{
		.code			= BTN_0,
		.gpio			= 23,
		.desc			= "button0",
		.wakeup			= 1,
	},
	{
		.code			= BTN_1,
		.gpio			= 14,
		.desc			= "button1",
		.wakeup			= 1,
	},
};

static struct gpio_keys_platform_data gpio_keys_pdata = {
	.buttons	= gpio_buttons,
	.nbuttons	= ARRAY_SIZE(gpio_buttons),
};

static struct platform_device gpio_keys_device = {
	.name	= "gpio-keys",
	.id	= -1,
	.dev	= {
		.platform_data	= &gpio_keys_pdata,
	},
};

static void __init overo_init_keys(void)
{
	platform_device_register(&gpio_keys_device);
}

#else
static inline void __init overo_init_keys(void) { return; }
#endif

static int overo_twl_gpio_setup(struct device *dev,
		unsigned gpio, unsigned ngpio)
{
	omap2_hsmmc_init(mmc);

#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
	/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
	gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif

	return 0;
}

static struct twl4030_gpio_platform_data overo_gpio_data = {
	.gpio_base	= OMAP_MAX_GPIO_LINES,
	.irq_base	= TWL4030_GPIO_IRQ_BASE,
	.irq_end	= TWL4030_GPIO_IRQ_END,
	.use_leds	= true,
	.setup		= overo_twl_gpio_setup,
};

static struct regulator_init_data overo_vmmc1 = {
	.constraints = {
		.min_uV			= 1850000,
		.max_uV			= 3150000,
		.valid_modes_mask	= REGULATOR_MODE_NORMAL
					| REGULATOR_MODE_STANDBY,
		.valid_ops_mask		= REGULATOR_CHANGE_VOLTAGE
					| REGULATOR_CHANGE_MODE
					| REGULATOR_CHANGE_STATUS,
	},
	.num_consumer_supplies	= ARRAY_SIZE(overo_vmmc1_supply),
	.consumer_supplies	= overo_vmmc1_supply,
};

static struct twl4030_platform_data overo_twldata = {
	.gpio		= &overo_gpio_data,
	.vmmc1		= &overo_vmmc1,
};

static int __init overo_i2c_init(void)
{
	omap3_pmic_get_config(&overo_twldata,
			TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
			TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);

	overo_twldata.vpll2->constraints.name = "VDVI";

	omap3_pmic_init("tps65950", &overo_twldata);
	/* i2c2 pins are used for gpio */
	omap_register_i2c_bus(3, 400, NULL, 0);
	return 0;
}

static struct spi_board_info overo_spi_board_info[] __initdata = {
#if defined(CONFIG_PANEL_LGPHILIPS_LB035Q02) || \
	defined(CONFIG_PANEL_LGPHILIPS_LB035Q02_MODULE)
	{
		.modalias		= "lgphilips_lb035q02_panel-spi",
		.bus_num		= 1,
		.chip_select		= 1,
		.max_speed_hz		= 500000,
		.mode			= SPI_MODE_3,
	},
#endif
};

static int __init overo_spi_init(void)
{
	overo_ads7846_init();
	spi_register_board_info(overo_spi_board_info,
			ARRAY_SIZE(overo_spi_board_info));
	return 0;
}

static void __init overo_init_early(void)
{
	omap2_init_common_infrastructure();
	omap2_init_common_devices(mt46h32m32lf6_sdrc_params,
				  mt46h32m32lf6_sdrc_params);
}

static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
	.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
	.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
	.port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
	.phy_reset  = true,
	.reset_gpio_port[0]  = -EINVAL,
	.reset_gpio_port[1]  = OVERO_GPIO_USBH_NRESET,
	.reset_gpio_port[2]  = -EINVAL
};

#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
	{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif

static struct gpio overo_bt_gpios[] __initdata = {
	{ OVERO_GPIO_BT_XGATE,	GPIOF_OUT_INIT_LOW,	"lcd enable"    },
	{ OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH,	"lcd bl enable" },
};

static void __init overo_init(void)
{
	int ret;

	omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
	overo_i2c_init();
	omap_display_init(&overo_dss_data);
	omap_serial_init();
	omap_nand_flash_init(0, overo_nand_partitions,
			     ARRAY_SIZE(overo_nand_partitions));
	usb_musb_init(NULL);
	usbhs_init(&usbhs_bdata);
	overo_spi_init();
	overo_init_smsc911x();
	overo_display_init();
	overo_init_led();
	overo_init_keys();

	/* Ensure SDRC pins are mux'd for self-refresh */
	omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
	omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);

	ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH,
			       "OVERO_GPIO_W2W_NRESET");
	if (ret == 0) {
		gpio_export(OVERO_GPIO_W2W_NRESET, 0);
		gpio_set_value(OVERO_GPIO_W2W_NRESET, 0);
		udelay(10);
		gpio_set_value(OVERO_GPIO_W2W_NRESET, 1);
	} else {
		printk(KERN_ERR "could not obtain gpio for "
					"OVERO_GPIO_W2W_NRESET\n");
	}

	ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios));
	if (ret) {
		pr_err("%s: could not obtain BT gpios\n", __func__);
	} else {
		gpio_export(OVERO_GPIO_BT_XGATE, 0);
		gpio_export(OVERO_GPIO_BT_NRESET, 0);
		gpio_set_value(OVERO_GPIO_BT_NRESET, 0);
		mdelay(6);
		gpio_set_value(OVERO_GPIO_BT_NRESET, 1);
	}

	ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH,
			       "OVERO_GPIO_USBH_CPEN");
	if (ret == 0)
		gpio_export(OVERO_GPIO_USBH_CPEN, 0);
	else
		printk(KERN_ERR "could not obtain gpio for "
					"OVERO_GPIO_USBH_CPEN\n");
}

MACHINE_START(OVERO, "Gumstix Overo")
	.boot_params	= 0x80000100,
	.reserve	= omap_reserve,
	.map_io		= omap3_map_io,
	.init_early	= overo_init_early,
	.init_irq	= omap3_init_irq,
	.init_machine	= overo_init,
	.timer		= &omap3_timer,
MACHINE_END