blob: 7939b6d712706d9e20df1aed03ac4e6796e59a25 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001#ifndef _SUNZILOG_H
2#define _SUNZILOG_H
3
4struct zilog_channel {
5 volatile unsigned char control;
6 volatile unsigned char __pad1;
7 volatile unsigned char data;
8 volatile unsigned char __pad2;
9};
10
11struct zilog_layout {
12 struct zilog_channel channelB;
13 struct zilog_channel channelA;
14};
15
16#define NUM_ZSREGS 16
17
18/* Conversion routines to/from brg time constants from/to bits
19 * per second.
20 */
21#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2))
22#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2)
23
24/* The Zilog register set */
25
26#define FLAG 0x7e
27
28/* Write Register 0 */
29#define R0 0 /* Register selects */
30#define R1 1
31#define R2 2
32#define R3 3
33#define R4 4
34#define R5 5
35#define R6 6
36#define R7 7
37#define R8 8
38#define R9 9
39#define R10 10
40#define R11 11
41#define R12 12
42#define R13 13
43#define R14 14
44#define R15 15
45
46#define NULLCODE 0 /* Null Code */
47#define POINT_HIGH 0x8 /* Select upper half of registers */
48#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */
49#define SEND_ABORT 0x18 /* HDLC Abort */
50#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */
51#define RES_Tx_P 0x28 /* Reset TxINT Pending */
52#define ERR_RES 0x30 /* Error Reset */
53#define RES_H_IUS 0x38 /* Reset highest IUS */
54
55#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */
56#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */
57#define RES_EOM_L 0xC0 /* Reset EOM latch */
58
59/* Write Register 1 */
60
61#define EXT_INT_ENAB 0x1 /* Ext Int Enable */
62#define TxINT_ENAB 0x2 /* Tx Int Enable */
63#define PAR_SPEC 0x4 /* Parity is special condition */
64
65#define RxINT_DISAB 0 /* Rx Int Disable */
66#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */
67#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */
68#define INT_ERR_Rx 0x18 /* Int on error only */
69#define RxINT_MASK 0x18
70
71#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */
72#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */
73#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */
74
75/* Write Register #2 (Interrupt Vector) */
76
77/* Write Register 3 */
78
79#define RxENAB 0x1 /* Rx Enable */
80#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */
81#define ADD_SM 0x4 /* Address Search Mode (SDLC) */
82#define RxCRC_ENAB 0x8 /* Rx CRC Enable */
83#define ENT_HM 0x10 /* Enter Hunt Mode */
84#define AUTO_ENAB 0x20 /* Auto Enables */
85#define Rx5 0x0 /* Rx 5 Bits/Character */
86#define Rx7 0x40 /* Rx 7 Bits/Character */
87#define Rx6 0x80 /* Rx 6 Bits/Character */
88#define Rx8 0xc0 /* Rx 8 Bits/Character */
89#define RxN_MASK 0xc0
90
91/* Write Register 4 */
92
93#define PAR_ENAB 0x1 /* Parity Enable */
94#define PAR_EVEN 0x2 /* Parity Even/Odd* */
95
96#define SYNC_ENAB 0 /* Sync Modes Enable */
97#define SB1 0x4 /* 1 stop bit/char */
98#define SB15 0x8 /* 1.5 stop bits/char */
99#define SB2 0xc /* 2 stop bits/char */
100
101#define MONSYNC 0 /* 8 Bit Sync character */
102#define BISYNC 0x10 /* 16 bit sync character */
103#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */
104#define EXTSYNC 0x30 /* External Sync Mode */
105
106#define X1CLK 0x0 /* x1 clock mode */
107#define X16CLK 0x40 /* x16 clock mode */
108#define X32CLK 0x80 /* x32 clock mode */
109#define X64CLK 0xC0 /* x64 clock mode */
110#define XCLK_MASK 0xC0
111
112/* Write Register 5 */
113
114#define TxCRC_ENAB 0x1 /* Tx CRC Enable */
115#define RTS 0x2 /* RTS */
116#define SDLC_CRC 0x4 /* SDLC/CRC-16 */
117#define TxENAB 0x8 /* Tx Enable */
118#define SND_BRK 0x10 /* Send Break */
119#define Tx5 0x0 /* Tx 5 bits (or less)/character */
120#define Tx7 0x20 /* Tx 7 bits/character */
121#define Tx6 0x40 /* Tx 6 bits/character */
122#define Tx8 0x60 /* Tx 8 bits/character */
123#define TxN_MASK 0x60
124#define DTR 0x80 /* DTR */
125
126/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */
127
128/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */
129
130/* Write Register 8 (transmit buffer) */
131
132/* Write Register 9 (Master interrupt control) */
133#define VIS 1 /* Vector Includes Status */
134#define NV 2 /* No Vector */
135#define DLC 4 /* Disable Lower Chain */
136#define MIE 8 /* Master Interrupt Enable */
137#define STATHI 0x10 /* Status high */
138#define NORESET 0 /* No reset on write to R9 */
139#define CHRB 0x40 /* Reset channel B */
140#define CHRA 0x80 /* Reset channel A */
141#define FHWRES 0xc0 /* Force hardware reset */
142
143/* Write Register 10 (misc control bits) */
144#define BIT6 1 /* 6 bit/8bit sync */
145#define LOOPMODE 2 /* SDLC Loop mode */
146#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */
147#define MARKIDLE 8 /* Mark/flag on idle */
148#define GAOP 0x10 /* Go active on poll */
149#define NRZ 0 /* NRZ mode */
150#define NRZI 0x20 /* NRZI mode */
151#define FM1 0x40 /* FM1 (transition = 1) */
152#define FM0 0x60 /* FM0 (transition = 0) */
153#define CRCPS 0x80 /* CRC Preset I/O */
154
155/* Write Register 11 (Clock Mode control) */
156#define TRxCXT 0 /* TRxC = Xtal output */
157#define TRxCTC 1 /* TRxC = Transmit clock */
158#define TRxCBR 2 /* TRxC = BR Generator Output */
159#define TRxCDP 3 /* TRxC = DPLL output */
160#define TRxCOI 4 /* TRxC O/I */
161#define TCRTxCP 0 /* Transmit clock = RTxC pin */
162#define TCTRxCP 8 /* Transmit clock = TRxC pin */
163#define TCBR 0x10 /* Transmit clock = BR Generator output */
164#define TCDPLL 0x18 /* Transmit clock = DPLL output */
165#define RCRTxCP 0 /* Receive clock = RTxC pin */
166#define RCTRxCP 0x20 /* Receive clock = TRxC pin */
167#define RCBR 0x40 /* Receive clock = BR Generator output */
168#define RCDPLL 0x60 /* Receive clock = DPLL output */
169#define RTxCX 0x80 /* RTxC Xtal/No Xtal */
170
171/* Write Register 12 (lower byte of baud rate generator time constant) */
172
173/* Write Register 13 (upper byte of baud rate generator time constant) */
174
175/* Write Register 14 (Misc control bits) */
176#define BRENAB 1 /* Baud rate generator enable */
177#define BRSRC 2 /* Baud rate generator source */
178#define DTRREQ 4 /* DTR/Request function */
179#define AUTOECHO 8 /* Auto Echo */
180#define LOOPBAK 0x10 /* Local loopback */
181#define SEARCH 0x20 /* Enter search mode */
182#define RMC 0x40 /* Reset missing clock */
183#define DISDPLL 0x60 /* Disable DPLL */
184#define SSBR 0x80 /* Set DPLL source = BR generator */
185#define SSRTxC 0xa0 /* Set DPLL source = RTxC */
186#define SFMM 0xc0 /* Set FM mode */
187#define SNRZI 0xe0 /* Set NRZI mode */
188
189/* Write Register 15 (external/status interrupt control) */
190#define ZCIE 2 /* Zero count IE */
191#define DCDIE 8 /* DCD IE */
192#define SYNCIE 0x10 /* Sync/hunt IE */
193#define CTSIE 0x20 /* CTS IE */
194#define TxUIE 0x40 /* Tx Underrun/EOM IE */
195#define BRKIE 0x80 /* Break/Abort IE */
196
197
198/* Read Register 0 */
199#define Rx_CH_AV 0x1 /* Rx Character Available */
200#define ZCOUNT 0x2 /* Zero count */
201#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */
202#define DCD 0x8 /* DCD */
203#define SYNC 0x10 /* Sync/hunt */
204#define CTS 0x20 /* CTS */
205#define TxEOM 0x40 /* Tx underrun */
206#define BRK_ABRT 0x80 /* Break/Abort */
207
208/* Read Register 1 */
209#define ALL_SNT 0x1 /* All sent */
210/* Residue Data for 8 Rx bits/char programmed */
211#define RES3 0x8 /* 0/3 */
212#define RES4 0x4 /* 0/4 */
213#define RES5 0xc /* 0/5 */
214#define RES6 0x2 /* 0/6 */
215#define RES7 0xa /* 0/7 */
216#define RES8 0x6 /* 0/8 */
217#define RES18 0xe /* 1/8 */
218#define RES28 0x0 /* 2/8 */
219/* Special Rx Condition Interrupts */
220#define PAR_ERR 0x10 /* Parity error */
221#define Rx_OVR 0x20 /* Rx Overrun Error */
222#define CRC_ERR 0x40 /* CRC/Framing Error */
223#define END_FR 0x80 /* End of Frame (SDLC) */
224
225/* Read Register 2 (channel b only) - Interrupt vector */
226#define CHB_Tx_EMPTY 0x00
227#define CHB_EXT_STAT 0x02
228#define CHB_Rx_AVAIL 0x04
229#define CHB_SPECIAL 0x06
230#define CHA_Tx_EMPTY 0x08
231#define CHA_EXT_STAT 0x0a
232#define CHA_Rx_AVAIL 0x0c
233#define CHA_SPECIAL 0x0e
234#define STATUS_MASK 0x0e
235
236/* Read Register 3 (interrupt pending register) ch a only */
237#define CHBEXT 0x1 /* Channel B Ext/Stat IP */
238#define CHBTxIP 0x2 /* Channel B Tx IP */
239#define CHBRxIP 0x4 /* Channel B Rx IP */
240#define CHAEXT 0x8 /* Channel A Ext/Stat IP */
241#define CHATxIP 0x10 /* Channel A Tx IP */
242#define CHARxIP 0x20 /* Channel A Rx IP */
243
244/* Read Register 8 (receive data register) */
245
246/* Read Register 10 (misc status bits) */
247#define ONLOOP 2 /* On loop */
248#define LOOPSEND 0x10 /* Loop sending */
249#define CLK2MIS 0x40 /* Two clocks missing */
250#define CLK1MIS 0x80 /* One clock missing */
251
252/* Read Register 12 (lower byte of baud rate generator constant) */
253
254/* Read Register 13 (upper byte of baud rate generator constant) */
255
256/* Read Register 15 (value of WR 15) */
257
258/* Misc macros */
259#define ZS_CLEARERR(channel) do { sbus_writeb(ERR_RES, &channel->control); \
260 udelay(5); } while(0)
261
262#define ZS_CLEARSTAT(channel) do { sbus_writeb(RES_EXT_INT, &channel->control); \
263 udelay(5); } while(0)
264
265#define ZS_CLEARFIFO(channel) do { sbus_readb(&channel->data); \
266 udelay(2); \
267 sbus_readb(&channel->data); \
268 udelay(2); \
269 sbus_readb(&channel->data); \
270 udelay(2); } while(0)
271
272#endif /* _SUNZILOG_H */