David Collins | bbed9aa | 2017-03-10 11:53:10 -0800 | [diff] [blame] | 1 | /* Copyright (c) 2016-2017, The Linux Foundation. All rights reserved. |
| 2 | * |
| 3 | * This program is free software; you can redistribute it and/or modify |
| 4 | * it under the terms of the GNU General Public License version 2 and |
| 5 | * only version 2 as published by the Free Software Foundation. |
| 6 | * |
| 7 | * This program is distributed in the hope that it will be useful, |
| 8 | * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| 9 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| 10 | * GNU General Public License for more details. |
| 11 | */ |
| 12 | |
| 13 | #include <dt-bindings/spmi/spmi.h> |
| 14 | #include <dt-bindings/interrupt-controller/irq.h> |
| 15 | |
| 16 | &spmi_bus { |
| 17 | qcom,pmi8998@2 { |
| 18 | compatible = "qcom,spmi-pmic"; |
| 19 | reg = <0x2 SPMI_USID>; |
| 20 | #address-cells = <2>; |
| 21 | #size-cells = <0>; |
| 22 | |
| 23 | pmi8998_revid: qcom,revid@100 { |
| 24 | compatible = "qcom,qpnp-revid"; |
| 25 | reg = <0x100 0x100>; |
| 26 | qcom,fab-id-valid; |
| 27 | }; |
| 28 | |
| 29 | qcom,power-on@800 { |
| 30 | compatible = "qcom,qpnp-power-on"; |
| 31 | reg = <0x800 0x100>; |
| 32 | }; |
| 33 | |
| 34 | qcom,temp-alarm@2400 { |
| 35 | compatible = "qcom,qpnp-temp-alarm"; |
| 36 | reg = <0x2400 0x100>; |
| 37 | interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_RISING>; |
| 38 | label = "pmi8998_tz"; |
| 39 | }; |
| 40 | |
Fenglin Wu | 5a50fc8 | 2017-03-22 12:27:31 +0800 | [diff] [blame] | 41 | pmi8998_gpios: pinctrl@c000 { |
| 42 | compatible = "qcom,spmi-gpio"; |
| 43 | reg = <0xc000 0xe00>; |
| 44 | interrupts = <0x2 0xc0 0 IRQ_TYPE_NONE>, |
| 45 | <0x2 0xc1 0 IRQ_TYPE_NONE>, |
| 46 | <0x2 0xc2 0 IRQ_TYPE_NONE>, |
| 47 | <0x2 0xc4 0 IRQ_TYPE_NONE>, |
| 48 | <0x2 0xc5 0 IRQ_TYPE_NONE>, |
| 49 | <0x2 0xc7 0 IRQ_TYPE_NONE>, |
| 50 | <0x2 0xc8 0 IRQ_TYPE_NONE>, |
| 51 | <0x2 0xc9 0 IRQ_TYPE_NONE>, |
| 52 | <0x2 0xca 0 IRQ_TYPE_NONE>, |
| 53 | <0x2 0xcb 0 IRQ_TYPE_NONE>, |
| 54 | <0x2 0xcd 0 IRQ_TYPE_NONE>; |
| 55 | interrupt-names = "pmi8998_gpio1", "pmi8998_gpio2", |
| 56 | "pmi8998_gpio3", "pmi8998_gpio5", |
| 57 | "pmi8998_gpio6", "pmi8998_gpio8", |
| 58 | "pmi8998_gpio9", "pmi8998_gpio10", |
| 59 | "pmi8998_gpio11", "pmi8998_gpio12", |
| 60 | "pmi8998_gpio14"; |
David Collins | bbed9aa | 2017-03-10 11:53:10 -0800 | [diff] [blame] | 61 | gpio-controller; |
| 62 | #gpio-cells = <2>; |
Fenglin Wu | 5a50fc8 | 2017-03-22 12:27:31 +0800 | [diff] [blame] | 63 | qcom,gpios-disallowed = <4 7 13>; |
David Collins | bbed9aa | 2017-03-10 11:53:10 -0800 | [diff] [blame] | 64 | }; |
| 65 | |
| 66 | pmi8998_rradc: rradc@4500 { |
| 67 | compatible = "qcom,rradc"; |
| 68 | reg = <0x4500 0x100>; |
| 69 | #address-cells = <1>; |
| 70 | #size-cells = <0>; |
| 71 | #io-channel-cells = <1>; |
| 72 | qcom,pmic-revid = <&pmi8998_revid>; |
| 73 | }; |
| 74 | }; |
| 75 | |
| 76 | qcom,pmi8998@3 { |
| 77 | compatible ="qcom,spmi-pmic"; |
| 78 | reg = <0x3 SPMI_USID>; |
| 79 | #address-cells = <2>; |
| 80 | #size-cells = <0>; |
| 81 | |
| 82 | pmi8998_pwm_1: pwm@b100 { |
| 83 | compatible = "qcom,qpnp-pwm"; |
| 84 | reg = <0xb100 0x100>, |
| 85 | <0xb042 0x7e>; |
| 86 | reg-names = "qpnp-lpg-channel-base", |
| 87 | "qpnp-lpg-lut-base"; |
| 88 | qcom,lpg-lut-size = <0x7e>; |
| 89 | qcom,channel-id = <1>; |
| 90 | qcom,supported-sizes = <6>, <9>; |
| 91 | qcom,ramp-index = <0>; |
| 92 | #pwm-cells = <2>; |
| 93 | status = "disabled"; |
| 94 | }; |
| 95 | |
| 96 | pmi8998_pwm_2: pwm@b200 { |
| 97 | compatible = "qcom,qpnp-pwm"; |
| 98 | reg = <0xb200 0x100>, |
| 99 | <0xb042 0x7e>; |
| 100 | reg-names = "qpnp-lpg-channel-base", |
| 101 | "qpnp-lpg-lut-base"; |
| 102 | qcom,lpg-lut-size = <0x7e>; |
| 103 | qcom,channel-id = <2>; |
| 104 | qcom,supported-sizes = <6>, <9>; |
| 105 | qcom,ramp-index = <1>; |
| 106 | #pwm-cells = <2>; |
| 107 | status = "disabled"; |
| 108 | }; |
| 109 | |
| 110 | pmi8998_pwm_3: pwm@b300 { |
| 111 | compatible = "qcom,qpnp-pwm"; |
| 112 | reg = <0xb300 0x100>, |
| 113 | <0xb042 0x7e>; |
| 114 | reg-names = "qpnp-lpg-channel-base", |
| 115 | "qpnp-lpg-lut-base"; |
| 116 | qcom,lpg-lut-size = <0x7e>; |
| 117 | qcom,channel-id = <3>; |
| 118 | qcom,supported-sizes = <6>, <9>; |
| 119 | qcom,ramp-index = <2>; |
| 120 | #pwm-cells = <2>; |
| 121 | }; |
| 122 | |
| 123 | pmi8998_pwm_4: pwm@b400 { |
| 124 | compatible = "qcom,qpnp-pwm"; |
| 125 | reg = <0xb400 0x100>, |
| 126 | <0xb042 0x7e>; |
| 127 | reg-names = "qpnp-lpg-channel-base", |
| 128 | "qpnp-lpg-lut-base"; |
| 129 | qcom,lpg-lut-size = <0x7e>; |
| 130 | qcom,channel-id = <4>; |
| 131 | qcom,supported-sizes = <6>, <9>; |
| 132 | qcom,ramp-index = <3>; |
| 133 | #pwm-cells = <2>; |
| 134 | }; |
| 135 | |
| 136 | pmi8998_pwm_5: pwm@b500 { |
| 137 | compatible = "qcom,qpnp-pwm"; |
| 138 | reg = <0xb500 0x100>, |
| 139 | <0xb042 0x7e>; |
| 140 | reg-names = "qpnp-lpg-channel-base", |
| 141 | "qpnp-lpg-lut-base"; |
| 142 | qcom,lpg-lut-size = <0x7e>; |
| 143 | qcom,channel-id = <5>; |
| 144 | qcom,supported-sizes = <6>, <9>; |
| 145 | qcom,ramp-index = <4>; |
| 146 | #pwm-cells = <2>; |
| 147 | }; |
| 148 | |
| 149 | pmi8998_pwm_6: pwm@b600 { |
| 150 | compatible = "qcom,qpnp-pwm"; |
| 151 | reg = <0xb600 0x100>, |
| 152 | <0xb042 0x7e>; |
| 153 | reg-names = "qpnp-lpg-channel-base", |
| 154 | "qpnp-lpg-lut-base"; |
| 155 | qcom,lpg-lut-size = <0x7e>; |
| 156 | qcom,channel-id = <6>; |
| 157 | qcom,supported-sizes = <6>, <9>; |
| 158 | qcom,ramp-index = <5>; |
| 159 | #pwm-cells = <2>; |
| 160 | status = "disabled"; |
| 161 | }; |
| 162 | |
| 163 | qcom,leds@d000 { |
| 164 | compatible = "qcom,leds-qpnp"; |
| 165 | reg = <0xd000 0x100>; |
| 166 | label = "rgb"; |
| 167 | status = "okay"; |
| 168 | |
| 169 | red_led: qcom,rgb_0 { |
| 170 | label = "rgb"; |
| 171 | qcom,id = <3>; |
| 172 | qcom,mode = "pwm"; |
| 173 | pwms = <&pmi8998_pwm_5 0 0>; |
| 174 | qcom,pwm-us = <1000>; |
| 175 | qcom,max-current = <12>; |
| 176 | qcom,default-state = "off"; |
| 177 | linux,name = "red"; |
| 178 | linux,default-trigger = "battery-charging"; |
| 179 | }; |
| 180 | |
| 181 | green_led: qcom,rgb_1 { |
| 182 | label = "rgb"; |
| 183 | qcom,id = <4>; |
| 184 | qcom,mode = "pwm"; |
| 185 | pwms = <&pmi8998_pwm_4 0 0>; |
| 186 | qcom,pwm-us = <1000>; |
| 187 | qcom,max-current = <12>; |
| 188 | qcom,default-state = "off"; |
| 189 | linux,name = "green"; |
| 190 | linux,default-trigger = "battery-full"; |
| 191 | }; |
| 192 | |
| 193 | blue_led: qcom,rgb_2 { |
| 194 | label = "rgb"; |
| 195 | qcom,id = <5>; |
| 196 | qcom,mode = "pwm"; |
| 197 | pwms = <&pmi8998_pwm_3 0 0>; |
| 198 | qcom,pwm-us = <1000>; |
| 199 | qcom,max-current = <12>; |
| 200 | qcom,default-state = "off"; |
| 201 | linux,name = "blue"; |
| 202 | linux,default-trigger = "boot-indication"; |
| 203 | }; |
| 204 | }; |
| 205 | |
| 206 | labibb: qpnp-labibb-regulator { |
| 207 | compatible = "qcom,qpnp-labibb-regulator"; |
| 208 | #address-cells = <1>; |
| 209 | #size-cells = <1>; |
| 210 | qcom,pmic-revid = <&pmi8998_revid>; |
| 211 | status = "disabled"; |
| 212 | |
| 213 | ibb_regulator: qcom,ibb@dc00 { |
| 214 | reg = <0xdc00 0x100>; |
| 215 | reg-names = "ibb_reg"; |
| 216 | regulator-name = "ibb_reg"; |
| 217 | |
| 218 | regulator-min-microvolt = <4600000>; |
| 219 | regulator-max-microvolt = <6000000>; |
| 220 | |
| 221 | qcom,qpnp-ibb-min-voltage = <1400000>; |
| 222 | qcom,qpnp-ibb-step-size = <100000>; |
| 223 | qcom,qpnp-ibb-slew-rate = <2000000>; |
| 224 | qcom,qpnp-ibb-use-default-voltage; |
| 225 | qcom,qpnp-ibb-init-voltage = <5500000>; |
| 226 | qcom,qpnp-ibb-init-amoled-voltage = <4000000>; |
| 227 | qcom,qpnp-ibb-init-lcd-voltage = <5500000>; |
| 228 | |
| 229 | qcom,qpnp-ibb-soft-start = <1000>; |
| 230 | |
| 231 | qcom,qpnp-ibb-lab-pwrup-delay = <8000>; |
| 232 | qcom,qpnp-ibb-lab-pwrdn-delay = <8000>; |
| 233 | qcom,qpnp-ibb-en-discharge; |
| 234 | |
| 235 | qcom,qpnp-ibb-full-pull-down; |
| 236 | qcom,qpnp-ibb-pull-down-enable; |
| 237 | qcom,qpnp-ibb-switching-clock-frequency = |
| 238 | <1480>; |
| 239 | qcom,qpnp-ibb-limit-maximum-current = <1550>; |
| 240 | qcom,qpnp-ibb-debounce-cycle = <16>; |
| 241 | qcom,qpnp-ibb-limit-max-current-enable; |
| 242 | qcom,qpnp-ibb-ps-enable; |
| 243 | }; |
| 244 | |
| 245 | lab_regulator: qcom,lab@de00 { |
| 246 | reg = <0xde00 0x100>; |
| 247 | reg-names = "lab"; |
| 248 | regulator-name = "lab_reg"; |
| 249 | |
| 250 | regulator-min-microvolt = <4600000>; |
| 251 | regulator-max-microvolt = <6000000>; |
| 252 | |
| 253 | interrupts = <0x3 0xde 0x0 |
| 254 | IRQ_TYPE_EDGE_RISING>; |
| 255 | interrupt-names = "lab-vreg-ok"; |
| 256 | qcom,qpnp-lab-min-voltage = <4600000>; |
| 257 | qcom,qpnp-lab-step-size = <100000>; |
| 258 | qcom,qpnp-lab-slew-rate = <5000>; |
| 259 | qcom,qpnp-lab-use-default-voltage; |
| 260 | qcom,qpnp-lab-init-voltage = <5500000>; |
| 261 | qcom,qpnp-lab-init-amoled-voltage = <4600000>; |
| 262 | qcom,qpnp-lab-init-lcd-voltage = <5500000>; |
| 263 | |
| 264 | qcom,qpnp-lab-soft-start = <800>; |
| 265 | |
| 266 | qcom,qpnp-lab-full-pull-down; |
| 267 | qcom,qpnp-lab-pull-down-enable; |
| 268 | qcom,qpnp-lab-switching-clock-frequency = |
| 269 | <1600>; |
| 270 | qcom,qpnp-lab-limit-maximum-current = <1600>; |
| 271 | qcom,qpnp-lab-limit-max-current-enable; |
| 272 | qcom,qpnp-lab-ps-threshold = <20>; |
| 273 | qcom,qpnp-lab-ps-enable; |
| 274 | qcom,qpnp-lab-nfet-size = <100>; |
| 275 | qcom,qpnp-lab-pfet-size = <100>; |
| 276 | qcom,qpnp-lab-max-precharge-time = <500>; |
| 277 | }; |
| 278 | }; |
| 279 | |
| 280 | pmi8998_wled: qcom,leds@d800 { |
| 281 | compatible = "qcom,qpnp-wled"; |
| 282 | reg = <0xd800 0x100>, |
| 283 | <0xd900 0x100>; |
| 284 | reg-names = "qpnp-wled-ctrl-base", |
| 285 | "qpnp-wled-sink-base"; |
| 286 | interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>, |
| 287 | <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>; |
| 288 | interrupt-names = "ovp-irq", "sc-irq"; |
| 289 | linux,name = "wled"; |
| 290 | linux,default-trigger = "bkl-trigger"; |
| 291 | qcom,fdbk-output = "auto"; |
| 292 | qcom,vref-uv = <127500>; |
| 293 | qcom,switch-freq-khz = <800>; |
| 294 | qcom,ovp-mv = <29600>; |
| 295 | qcom,ilim-ma = <970>; |
| 296 | qcom,boost-duty-ns = <26>; |
| 297 | qcom,mod-freq-khz = <9600>; |
| 298 | qcom,dim-mode = "hybrid"; |
| 299 | qcom,hyb-thres = <625>; |
| 300 | qcom,sync-dly-us = <800>; |
| 301 | qcom,fs-curr-ua = <25000>; |
| 302 | qcom,cons-sync-write-delay-us = <1000>; |
| 303 | qcom,led-strings-list = [00 01 02 03]; |
| 304 | qcom,en-ext-pfet-sc-pro; |
| 305 | qcom,pmic-revid = <&pmi8998_revid>; |
| 306 | qcom,loop-auto-gm-en; |
Subbaraman Narayanamurthy | 1f92fc1 | 2017-03-30 15:41:45 -0700 | [diff] [blame^] | 307 | status = "disabled"; |
David Collins | bbed9aa | 2017-03-10 11:53:10 -0800 | [diff] [blame] | 308 | }; |
| 309 | |
| 310 | flash_led: qcom,leds@d300 { |
| 311 | compatible = "qcom,qpnp-flash-led-v2"; |
| 312 | status = "okay"; |
| 313 | reg = <0xd300 0x100>; |
| 314 | label = "flash"; |
| 315 | interrupts = <0x3 0xd3 0x0 IRQ_TYPE_EDGE_RISING>, |
| 316 | <0x3 0xd3 0x3 IRQ_TYPE_EDGE_RISING>, |
| 317 | <0x3 0xd3 0x4 IRQ_TYPE_EDGE_RISING>; |
| 318 | interrupt-names = "led-fault-irq", |
| 319 | "all-ramp-down-done-irq", |
| 320 | "all-ramp-up-done-irq"; |
| 321 | qcom,hdrm-auto-mode; |
| 322 | qcom,short-circuit-det; |
| 323 | qcom,open-circuit-det; |
| 324 | qcom,vph-droop-det; |
| 325 | qcom,thermal-derate-en; |
| 326 | qcom,thermal-derate-current = <200 500 1000>; |
| 327 | qcom,isc-delay = <192>; |
| 328 | qcom,pmic-revid = <&pmi8998_revid>; |
| 329 | |
| 330 | pmi8998_flash0: qcom,flash_0 { |
| 331 | label = "flash"; |
| 332 | qcom,led-name = "led:flash_0"; |
| 333 | qcom,max-current = <1500>; |
| 334 | qcom,default-led-trigger = "flash0_trigger"; |
| 335 | qcom,id = <0>; |
| 336 | qcom,current-ma = <1000>; |
| 337 | qcom,duration-ms = <1280>; |
| 338 | qcom,ires-ua = <12500>; |
| 339 | qcom,hdrm-voltage-mv = <325>; |
| 340 | qcom,hdrm-vol-hi-lo-win-mv = <100>; |
| 341 | }; |
| 342 | |
| 343 | pmi8998_flash1: qcom,flash_1 { |
| 344 | label = "flash"; |
| 345 | qcom,led-name = "led:flash_1"; |
| 346 | qcom,max-current = <1500>; |
| 347 | qcom,default-led-trigger = "flash1_trigger"; |
| 348 | qcom,id = <1>; |
| 349 | qcom,current-ma = <1000>; |
| 350 | qcom,duration-ms = <1280>; |
| 351 | qcom,ires-ua = <12500>; |
| 352 | qcom,hdrm-voltage-mv = <325>; |
| 353 | qcom,hdrm-vol-hi-lo-win-mv = <100>; |
| 354 | }; |
| 355 | |
| 356 | pmi8998_flash2: qcom,flash_2 { |
| 357 | label = "flash"; |
| 358 | qcom,led-name = "led:flash_2"; |
| 359 | qcom,max-current = <750>; |
| 360 | qcom,default-led-trigger = "flash2_trigger"; |
| 361 | qcom,id = <2>; |
| 362 | qcom,current-ma = <500>; |
| 363 | qcom,duration-ms = <1280>; |
| 364 | qcom,ires-ua = <12500>; |
| 365 | qcom,hdrm-voltage-mv = <325>; |
| 366 | qcom,hdrm-vol-hi-lo-win-mv = <100>; |
| 367 | }; |
| 368 | |
| 369 | pmi8998_torch0: qcom,torch_0 { |
| 370 | label = "torch"; |
| 371 | qcom,led-name = "led:torch_0"; |
| 372 | qcom,max-current = <500>; |
| 373 | qcom,default-led-trigger = "torch0_trigger"; |
| 374 | qcom,id = <0>; |
| 375 | qcom,current-ma = <300>; |
| 376 | qcom,ires-ua = <12500>; |
| 377 | qcom,hdrm-voltage-mv = <325>; |
| 378 | qcom,hdrm-vol-hi-lo-win-mv = <100>; |
| 379 | }; |
| 380 | |
| 381 | pmi8998_torch1: qcom,torch_1 { |
| 382 | label = "torch"; |
| 383 | qcom,led-name = "led:torch_1"; |
| 384 | qcom,max-current = <500>; |
| 385 | qcom,default-led-trigger = "torch1_trigger"; |
| 386 | qcom,id = <1>; |
| 387 | qcom,current-ma = <300>; |
| 388 | qcom,ires-ua = <12500>; |
| 389 | qcom,hdrm-voltage-mv = <325>; |
| 390 | qcom,hdrm-vol-hi-lo-win-mv = <100>; |
| 391 | }; |
| 392 | |
| 393 | pmi8998_torch2: qcom,torch_2 { |
| 394 | label = "torch"; |
| 395 | qcom,led-name = "led:torch_2"; |
| 396 | qcom,max-current = <500>; |
| 397 | qcom,default-led-trigger = "torch2_trigger"; |
| 398 | qcom,id = <2>; |
| 399 | qcom,current-ma = <300>; |
| 400 | qcom,ires-ua = <12500>; |
| 401 | qcom,hdrm-voltage-mv = <325>; |
| 402 | qcom,hdrm-vol-hi-lo-win-mv = <100>; |
| 403 | }; |
| 404 | |
| 405 | pmi8998_switch0: qcom,led_switch_0 { |
| 406 | label = "switch"; |
| 407 | qcom,led-name = "led:switch_0"; |
| 408 | qcom,led-mask = <3>; |
| 409 | qcom,default-led-trigger = "switch0_trigger"; |
| 410 | }; |
| 411 | |
| 412 | pmi8998_switch1: qcom,led_switch_1 { |
| 413 | label = "switch"; |
| 414 | qcom,led-name = "led:switch_1"; |
| 415 | qcom,led-mask = <4>; |
| 416 | qcom,default-led-trigger = "switch1_trigger"; |
| 417 | }; |
| 418 | }; |
| 419 | }; |
| 420 | }; |