drivers/net/wireless/iwlegacy/iwl-3945.c

/******************************************************************************
 *
 * Copyright(c) 2003 - 2011 Intel Corporation. All rights reserved.
 *
 * This program is free software; you can redistribute it and/or modify it
 * under the terms of version 2 of the GNU General Public License as
 * published by the Free Software Foundation.
 *
 * This program is distributed in the hope that it will be useful, but WITHOUT
 * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
 * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
 * more details.
 *
 * You should have received a copy of the GNU General Public License along with
 * this program; if not, write to the Free Software Foundation, Inc.,
 * 51 Franklin Street, Fifth Floor, Boston, MA 02110, USA
 *
 * The full GNU General Public License is included in this distribution in the
 * file called LICENSE.
 *
 * Contact Information:
 *  Intel Linux Wireless <ilw@linux.intel.com>
 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
 *
 *****************************************************************************/

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/dma-mapping.h>
#include <linux/delay.h>
#include <linux/sched.h>
#include <linux/skbuff.h>
#include <linux/netdevice.h>
#include <linux/firmware.h>
#include <linux/etherdevice.h>
#include <asm/unaligned.h>
#include <net/mac80211.h>

#include "iwl-fh.h"
#include "iwl-3945-fh.h"
#include "iwl-commands.h"
#include "iwl-sta.h"
#include "iwl-3945.h"
#include "iwl-eeprom.h"
#include "iwl-core.h"
#include "iwl-helpers.h"
#include "iwl-led.h"
#include "iwl-3945-led.h"
#include "iwl-3945-debugfs.h"

#define IL_DECLARE_RATE_INFO(r, ip, in, rp, rn, pp, np)    \
	[IL_RATE_##r##M_INDEX] = { IL_RATE_##r##M_PLCP,   \
				    IL_RATE_##r##M_IEEE,   \
				    IL_RATE_##ip##M_INDEX, \
				    IL_RATE_##in##M_INDEX, \
				    IL_RATE_##rp##M_INDEX, \
				    IL_RATE_##rn##M_INDEX, \
				    IL_RATE_##pp##M_INDEX, \
				    IL_RATE_##np##M_INDEX, \
				    IL_RATE_##r##M_INDEX_TABLE, \
				    IL_RATE_##ip##M_INDEX_TABLE }

/*
 * Parameter order:
 *   rate, prev rate, next rate, prev tgg rate, next tgg rate
 *
 * If there isn't a valid next or previous rate then INV is used which
 * maps to IL_RATE_INVALID
 *
 */
const struct il3945_rate_info il3945_rates[IL_RATE_COUNT_3945] = {
	IL_DECLARE_RATE_INFO(1, INV, 2, INV, 2, INV, 2),    /*  1mbps */
	IL_DECLARE_RATE_INFO(2, 1, 5, 1, 5, 1, 5),          /*  2mbps */
	IL_DECLARE_RATE_INFO(5, 2, 6, 2, 11, 2, 11),        /*5.5mbps */
	IL_DECLARE_RATE_INFO(11, 9, 12, 5, 12, 5, 18),      /* 11mbps */
	IL_DECLARE_RATE_INFO(6, 5, 9, 5, 11, 5, 11),        /*  6mbps */
	IL_DECLARE_RATE_INFO(9, 6, 11, 5, 11, 5, 11),       /*  9mbps */
	IL_DECLARE_RATE_INFO(12, 11, 18, 11, 18, 11, 18),   /* 12mbps */
	IL_DECLARE_RATE_INFO(18, 12, 24, 12, 24, 11, 24),   /* 18mbps */
	IL_DECLARE_RATE_INFO(24, 18, 36, 18, 36, 18, 36),   /* 24mbps */
	IL_DECLARE_RATE_INFO(36, 24, 48, 24, 48, 24, 48),   /* 36mbps */
	IL_DECLARE_RATE_INFO(48, 36, 54, 36, 54, 36, 54),   /* 48mbps */
	IL_DECLARE_RATE_INFO(54, 48, INV, 48, INV, 48, INV),/* 54mbps */
};

static inline u8 il3945_get_prev_ieee_rate(u8 rate_index)
{
	u8 rate = il3945_rates[rate_index].prev_ieee;

	if (rate == IL_RATE_INVALID)
		rate = rate_index;
	return rate;
}

/* 1 = enable the il3945_disable_events() function */
#define IL_EVT_DISABLE (0)
#define IL_EVT_DISABLE_SIZE (1532/32)

/**
 * il3945_disable_events - Disable selected events in uCode event log
 *
 * Disable an event by writing "1"s into "disable"
 *   bitmap in SRAM.  Bit position corresponds to Event # (id/type).
 *   Default values of 0 enable uCode events to be logged.
 * Use for only special debugging.  This function is just a placeholder as-is,
 *   you'll need to provide the special bits! ...
 *   ... and set IL_EVT_DISABLE to 1. */
void il3945_disable_events(struct il_priv *il)
{
	int i;
	u32 base;		/* SRAM address of event log header */
	u32 disable_ptr;	/* SRAM address of event-disable bitmap array */
	u32 array_size;		/* # of u32 entries in array */
	static const u32 evt_disable[IL_EVT_DISABLE_SIZE] = {
		0x00000000,	/*   31 -    0  Event id numbers */
		0x00000000,	/*   63 -   32 */
		0x00000000,	/*   95 -   64 */
		0x00000000,	/*  127 -   96 */
		0x00000000,	/*  159 -  128 */
		0x00000000,	/*  191 -  160 */
		0x00000000,	/*  223 -  192 */
		0x00000000,	/*  255 -  224 */
		0x00000000,	/*  287 -  256 */
		0x00000000,	/*  319 -  288 */
		0x00000000,	/*  351 -  320 */
		0x00000000,	/*  383 -  352 */
		0x00000000,	/*  415 -  384 */
		0x00000000,	/*  447 -  416 */
		0x00000000,	/*  479 -  448 */
		0x00000000,	/*  511 -  480 */
		0x00000000,	/*  543 -  512 */
		0x00000000,	/*  575 -  544 */
		0x00000000,	/*  607 -  576 */
		0x00000000,	/*  639 -  608 */
		0x00000000,	/*  671 -  640 */
		0x00000000,	/*  703 -  672 */
		0x00000000,	/*  735 -  704 */
		0x00000000,	/*  767 -  736 */
		0x00000000,	/*  799 -  768 */
		0x00000000,	/*  831 -  800 */
		0x00000000,	/*  863 -  832 */
		0x00000000,	/*  895 -  864 */
		0x00000000,	/*  927 -  896 */
		0x00000000,	/*  959 -  928 */
		0x00000000,	/*  991 -  960 */
		0x00000000,	/* 1023 -  992 */
		0x00000000,	/* 1055 - 1024 */
		0x00000000,	/* 1087 - 1056 */
		0x00000000,	/* 1119 - 1088 */
		0x00000000,	/* 1151 - 1120 */
		0x00000000,	/* 1183 - 1152 */
		0x00000000,	/* 1215 - 1184 */
		0x00000000,	/* 1247 - 1216 */
		0x00000000,	/* 1279 - 1248 */
		0x00000000,	/* 1311 - 1280 */
		0x00000000,	/* 1343 - 1312 */
		0x00000000,	/* 1375 - 1344 */
		0x00000000,	/* 1407 - 1376 */
		0x00000000,	/* 1439 - 1408 */
		0x00000000,	/* 1471 - 1440 */
		0x00000000,	/* 1503 - 1472 */
	};

	base = le32_to_cpu(il->card_alive.log_event_table_ptr);
	if (!il3945_hw_valid_rtc_data_addr(base)) {
		IL_ERR("Invalid event log pointer 0x%08X\n", base);
		return;
	}

	disable_ptr = il_read_targ_mem(il, base + (4 * sizeof(u32)));
	array_size = il_read_targ_mem(il, base + (5 * sizeof(u32)));

	if (IL_EVT_DISABLE && array_size == IL_EVT_DISABLE_SIZE) {
		D_INFO("Disabling selected uCode log events at 0x%x\n",
			       disable_ptr);
		for (i = 0; i < IL_EVT_DISABLE_SIZE; i++)
			il_write_targ_mem(il,
					   disable_ptr + (i * sizeof(u32)),
					   evt_disable[i]);

	} else {
		D_INFO("Selected uCode log events may be disabled\n");
		D_INFO("  by writing \"1\"s into disable bitmap\n");
		D_INFO("  in SRAM at 0x%x, size %d u32s\n",
			       disable_ptr, array_size);
	}

}

static int il3945_hwrate_to_plcp_idx(u8 plcp)
{
	int idx;

	for (idx = 0; idx < IL_RATE_COUNT_3945; idx++)
		if (il3945_rates[idx].plcp == plcp)
			return idx;
	return -1;
}

#ifdef CONFIG_IWLWIFI_LEGACY_DEBUG
#define TX_STATUS_ENTRY(x) case TX_3945_STATUS_FAIL_ ## x: return #x

static const char *il3945_get_tx_fail_reason(u32 status)
{
	switch (status & TX_STATUS_MSK) {
	case TX_3945_STATUS_SUCCESS:
		return "SUCCESS";
		TX_STATUS_ENTRY(SHORT_LIMIT);
		TX_STATUS_ENTRY(LONG_LIMIT);
		TX_STATUS_ENTRY(FIFO_UNDERRUN);
		TX_STATUS_ENTRY(MGMNT_ABORT);
		TX_STATUS_ENTRY(NEXT_FRAG);
		TX_STATUS_ENTRY(LIFE_EXPIRE);
		TX_STATUS_ENTRY(DEST_PS);
		TX_STATUS_ENTRY(ABORTED);
		TX_STATUS_ENTRY(BT_RETRY);
		TX_STATUS_ENTRY(STA_INVALID);
		TX_STATUS_ENTRY(FRAG_DROPPED);
		TX_STATUS_ENTRY(TID_DISABLE);
		TX_STATUS_ENTRY(FRAME_FLUSHED);
		TX_STATUS_ENTRY(INSUFFICIENT_CF_POLL);
		TX_STATUS_ENTRY(TX_LOCKED);
		TX_STATUS_ENTRY(NO_BEACON_ON_RADAR);
	}

	return "UNKNOWN";
}
#else
static inline const char *il3945_get_tx_fail_reason(u32 status)
{
	return "";
}
#endif

/*
 * get ieee prev rate from rate scale table.
 * for A and B mode we need to overright prev
 * value
 */
int il3945_rs_next_rate(struct il_priv *il, int rate)
{
	int next_rate = il3945_get_prev_ieee_rate(rate);

	switch (il->band) {
	case IEEE80211_BAND_5GHZ:
		if (rate == IL_RATE_12M_INDEX)
			next_rate = IL_RATE_9M_INDEX;
		else if (rate == IL_RATE_6M_INDEX)
			next_rate = IL_RATE_6M_INDEX;
		break;
	case IEEE80211_BAND_2GHZ:
		if (!(il->_3945.sta_supp_rates & IL_OFDM_RATES_MASK) &&
		    il_is_associated(il, IL_RXON_CTX_BSS)) {
			if (rate == IL_RATE_11M_INDEX)
				next_rate = IL_RATE_5M_INDEX;
		}
		break;

	default:
		break;
	}

	return next_rate;
}


/**
 * il3945_tx_queue_reclaim - Reclaim Tx queue entries already Tx'd
 *
 * When FW advances 'R' index, all entries between old and new 'R' index
 * need to be reclaimed. As result, some free space forms. If there is
 * enough free space (> low mark), wake the stack that feeds us.
 */
static void il3945_tx_queue_reclaim(struct il_priv *il,
				     int txq_id, int index)
{
	struct il_tx_queue *txq = &il->txq[txq_id];
	struct il_queue *q = &txq->q;
	struct il_tx_info *tx_info;

	BUG_ON(txq_id == IWL39_CMD_QUEUE_NUM);

	for (index = il_queue_inc_wrap(index, q->n_bd);
		q->read_ptr != index;
		q->read_ptr = il_queue_inc_wrap(q->read_ptr, q->n_bd)) {

		tx_info = &txq->txb[txq->q.read_ptr];
		ieee80211_tx_status_irqsafe(il->hw, tx_info->skb);
		tx_info->skb = NULL;
		il->cfg->ops->lib->txq_free_tfd(il, txq);
	}

	if (il_queue_space(q) > q->low_mark && txq_id >= 0 &&
	    txq_id != IWL39_CMD_QUEUE_NUM && il->mac80211_registered)
		il_wake_queue(il, txq);
}

/**
 * il3945_rx_reply_tx - Handle Tx response
 */
static void il3945_rx_reply_tx(struct il_priv *il,
				struct il_rx_mem_buffer *rxb)
{
	struct il_rx_packet *pkt = rxb_addr(rxb);
	u16 sequence = le16_to_cpu(pkt->hdr.sequence);
	int txq_id = SEQ_TO_QUEUE(sequence);
	int index = SEQ_TO_INDEX(sequence);
	struct il_tx_queue *txq = &il->txq[txq_id];
	struct ieee80211_tx_info *info;
	struct il3945_tx_resp *tx_resp = (void *)&pkt->u.raw[0];
	u32  status = le32_to_cpu(tx_resp->status);
	int rate_idx;
	int fail;

	if (index >= txq->q.n_bd || il_queue_used(&txq->q, index) == 0) {
		IL_ERR("Read index for DMA queue txq_id (%d) index %d "
			  "is out of range [0-%d] %d %d\n", txq_id,
			  index, txq->q.n_bd, txq->q.write_ptr,
			  txq->q.read_ptr);
		return;
	}

	txq->time_stamp = jiffies;
	info = IEEE80211_SKB_CB(txq->txb[txq->q.read_ptr].skb);
	ieee80211_tx_info_clear_status(info);

	/* Fill the MRR chain with some info about on-chip retransmissions */
	rate_idx = il3945_hwrate_to_plcp_idx(tx_resp->rate);
	if (info->band == IEEE80211_BAND_5GHZ)
		rate_idx -= IL_FIRST_OFDM_RATE;

	fail = tx_resp->failure_frame;

	info->status.rates[0].idx = rate_idx;
	info->status.rates[0].count = fail + 1; /* add final attempt */

	/* tx_status->rts_retry_count = tx_resp->failure_rts; */
	info->flags |= ((status & TX_STATUS_MSK) == TX_STATUS_SUCCESS) ?
				IEEE80211_TX_STAT_ACK : 0;

	D_TX("Tx queue %d Status %s (0x%08x) plcp rate %d retries %d\n",
			txq_id, il3945_get_tx_fail_reason(status), status,
			tx_resp->rate, tx_resp->failure_frame);

	D_TX_REPLY("Tx queue reclaim %d\n", index);
	il3945_tx_queue_reclaim(il, txq_id, index);

	if (status & TX_ABORT_REQUIRED_MSK)
		IL_ERR("TODO:  Implement Tx ABORT REQUIRED!!!\n");
}



/*****************************************************************************
 *
 * Intel PRO/Wireless 3945ABG/BG Network Connection
 *
 *  RX handler implementations
 *
 *****************************************************************************/
#ifdef CONFIG_IWLWIFI_LEGACY_DEBUGFS
static void il3945_accumulative_statistics(struct il_priv *il,
					    __le32 *stats)
{
	int i;
	__le32 *prev_stats;
	u32 *accum_stats;
	u32 *delta, *max_delta;

	prev_stats = (__le32 *)&il->_3945.statistics;
	accum_stats = (u32 *)&il->_3945.accum_statistics;
	delta = (u32 *)&il->_3945.delta_statistics;
	max_delta = (u32 *)&il->_3945.max_delta;

	for (i = sizeof(__le32); i < sizeof(struct il3945_notif_statistics);
	     i += sizeof(__le32), stats++, prev_stats++, delta++,
	     max_delta++, accum_stats++) {
		if (le32_to_cpu(*stats) > le32_to_cpu(*prev_stats)) {
			*delta = (le32_to_cpu(*stats) -
				le32_to_cpu(*prev_stats));
			*accum_stats += *delta;
			if (*delta > *max_delta)
				*max_delta = *delta;
		}
	}

	/* reset accumulative statistics for "no-counter" type statistics */
	il->_3945.accum_statistics.general.temperature =
		il->_3945.statistics.general.temperature;
	il->_3945.accum_statistics.general.ttl_timestamp =
		il->_3945.statistics.general.ttl_timestamp;
}
#endif

void il3945_hw_rx_statistics(struct il_priv *il,
		struct il_rx_mem_buffer *rxb)
{
	struct il_rx_packet *pkt = rxb_addr(rxb);

	D_RX("Statistics notification received (%d vs %d).\n",
		     (int)sizeof(struct il3945_notif_statistics),
		     le32_to_cpu(pkt->len_n_flags) & FH_RSCSR_FRAME_SIZE_MSK);
#ifdef CONFIG_IWLWIFI_LEGACY_DEBUGFS
	il3945_accumulative_statistics(il, (__le32 *)&pkt->u.raw);
#endif

	memcpy(&il->_3945.statistics, pkt->u.raw, sizeof(il->_3945.statistics));
}

void il3945_reply_statistics(struct il_priv *il,
			      struct il_rx_mem_buffer *rxb)
{
	struct il_rx_packet *pkt = rxb_addr(rxb);
	__le32 *flag = (__le32 *)&pkt->u.raw;

	if (le32_to_cpu(*flag) & UCODE_STATISTICS_CLEAR_MSK) {
#ifdef CONFIG_IWLWIFI_LEGACY_DEBUGFS
		memset(&il->_3945.accum_statistics, 0,
			sizeof(struct il3945_notif_statistics));
		memset(&il->_3945.delta_statistics, 0,
			sizeof(struct il3945_notif_statistics));
		memset(&il->_3945.max_delta, 0,
			sizeof(struct il3945_notif_statistics));
#endif
		D_RX("Statistics have been cleared\n");
	}
	il3945_hw_rx_statistics(il, rxb);
}


/******************************************************************************
 *
 * Misc. internal state and helper functions
 *
 ******************************************************************************/

/* This is necessary only for a number of statistics, see the caller. */
static int il3945_is_network_packet(struct il_priv *il,
		struct ieee80211_hdr *header)
{
	/* Filter incoming packets to determine if they are targeted toward
	 * this network, discarding packets coming from ourselves */
	switch (il->iw_mode) {
	case NL80211_IFTYPE_ADHOC: /* Header: Dest. | Source    | BSSID */
		/* packets to our IBSS update information */
		return !compare_ether_addr(header->addr3, il->bssid);
	case NL80211_IFTYPE_STATION: /* Header: Dest. | AP{BSSID} | Source */
		/* packets to our IBSS update information */
		return !compare_ether_addr(header->addr2, il->bssid);
	default:
		return 1;
	}
}

static void il3945_pass_packet_to_mac80211(struct il_priv *il,
				   struct il_rx_mem_buffer *rxb,
				   struct ieee80211_rx_status *stats)
{
	struct il_rx_packet *pkt = rxb_addr(rxb);
	struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)IL_RX_DATA(pkt);
	struct il3945_rx_frame_hdr *rx_hdr = IL_RX_HDR(pkt);
	struct il3945_rx_frame_end *rx_end = IL_RX_END(pkt);
	u16 len = le16_to_cpu(rx_hdr->len);
	struct sk_buff *skb;
	__le16 fc = hdr->frame_control;

	/* We received data from the HW, so stop the watchdog */
	if (unlikely(len + IWL39_RX_FRAME_SIZE >
		     PAGE_SIZE << il->hw_params.rx_page_order)) {
		D_DROP("Corruption detected!\n");
		return;
	}

	/* We only process data packets if the interface is open */
	if (unlikely(!il->is_open)) {
		D_DROP(
			"Dropping packet while interface is not open.\n");
		return;
	}

	skb = dev_alloc_skb(128);
	if (!skb) {
		IL_ERR("dev_alloc_skb failed\n");
		return;
	}

	if (!il3945_mod_params.sw_crypto)
		il_set_decrypted_flag(il,
				       (struct ieee80211_hdr *)rxb_addr(rxb),
				       le32_to_cpu(rx_end->status), stats);

	skb_add_rx_frag(skb, 0, rxb->page,
			(void *)rx_hdr->payload - (void *)pkt, len);

	il_update_stats(il, false, fc, len);
	memcpy(IEEE80211_SKB_RXCB(skb), stats, sizeof(*stats));

	ieee80211_rx(il->hw, skb);
	il->alloc_rxb_page--;
	rxb->page = NULL;
}

#define IL_DELAY_NEXT_SCAN_AFTER_ASSOC (HZ*6)

static void il3945_rx_reply_rx(struct il_priv *il,
				struct il_rx_mem_buffer *rxb)
{
	struct ieee80211_hdr *header;
	struct ieee80211_rx_status rx_status;
	struct il_rx_packet *pkt = rxb_addr(rxb);
	struct il3945_rx_frame_stats *rx_stats = IL_RX_STATS(pkt);
	struct il3945_rx_frame_hdr *rx_hdr = IL_RX_HDR(pkt);
	struct il3945_rx_frame_end *rx_end = IL_RX_END(pkt);
	u16 rx_stats_sig_avg __maybe_unused = le16_to_cpu(rx_stats->sig_avg);
	u16 rx_stats_noise_diff __maybe_unused = le16_to_cpu(rx_stats->noise_diff);
	u8 network_packet;

	rx_status.flag = 0;
	rx_status.mactime = le64_to_cpu(rx_end->timestamp);
	rx_status.band = (rx_hdr->phy_flags & RX_RES_PHY_FLAGS_BAND_24_MSK) ?
				IEEE80211_BAND_2GHZ : IEEE80211_BAND_5GHZ;
	rx_status.freq =
		ieee80211_channel_to_frequency(le16_to_cpu(rx_hdr->channel),
					       rx_status.band);

	rx_status.rate_idx = il3945_hwrate_to_plcp_idx(rx_hdr->rate);
	if (rx_status.band == IEEE80211_BAND_5GHZ)
		rx_status.rate_idx -= IL_FIRST_OFDM_RATE;

	rx_status.antenna = (le16_to_cpu(rx_hdr->phy_flags) &
					RX_RES_PHY_FLAGS_ANTENNA_MSK) >> 4;

	/* set the preamble flag if appropriate */
	if (rx_hdr->phy_flags & RX_RES_PHY_FLAGS_SHORT_PREAMBLE_MSK)
		rx_status.flag |= RX_FLAG_SHORTPRE;

	if ((unlikely(rx_stats->phy_count > 20))) {
		D_DROP("dsp size out of range [0,20]: %d/n",
				rx_stats->phy_count);
		return;
	}

	if (!(rx_end->status & RX_RES_STATUS_NO_CRC32_ERROR) ||
	    !(rx_end->status & RX_RES_STATUS_NO_RXE_OVERFLOW)) {
		D_RX("Bad CRC or FIFO: 0x%08X.\n", rx_end->status);
		return;
	}



	/* Convert 3945's rssi indicator to dBm */
	rx_status.signal = rx_stats->rssi - IWL39_RSSI_OFFSET;

	D_STATS("Rssi %d sig_avg %d noise_diff %d\n",
			rx_status.signal, rx_stats_sig_avg,
			rx_stats_noise_diff);

	header = (struct ieee80211_hdr *)IL_RX_DATA(pkt);

	network_packet = il3945_is_network_packet(il, header);

	D_STATS("[%c] %d RSSI:%d Signal:%u, Rate:%u\n",
			      network_packet ? '*' : ' ',
			      le16_to_cpu(rx_hdr->channel),
			      rx_status.signal, rx_status.signal,
			      rx_status.rate_idx);

	il_dbg_log_rx_data_frame(il, le16_to_cpu(rx_hdr->len),
						header);

	if (network_packet) {
		il->_3945.last_beacon_time =
			le32_to_cpu(rx_end->beacon_timestamp);
		il->_3945.last_tsf = le64_to_cpu(rx_end->timestamp);
		il->_3945.last_rx_rssi = rx_status.signal;
	}

	il3945_pass_packet_to_mac80211(il, rxb, &rx_status);
}

int il3945_hw_txq_attach_buf_to_tfd(struct il_priv *il,
				     struct il_tx_queue *txq,
				     dma_addr_t addr, u16 len, u8 reset, u8 pad)
{
	int count;
	struct il_queue *q;
	struct il3945_tfd *tfd, *tfd_tmp;

	q = &txq->q;
	tfd_tmp = (struct il3945_tfd *)txq->tfds;
	tfd = &tfd_tmp[q->write_ptr];

	if (reset)
		memset(tfd, 0, sizeof(*tfd));

	count = TFD_CTL_COUNT_GET(le32_to_cpu(tfd->control_flags));

	if (count >= NUM_TFD_CHUNKS || count < 0) {
		IL_ERR("Error can not send more than %d chunks\n",
			  NUM_TFD_CHUNKS);
		return -EINVAL;
	}

	tfd->tbs[count].addr = cpu_to_le32(addr);
	tfd->tbs[count].len = cpu_to_le32(len);

	count++;

	tfd->control_flags = cpu_to_le32(TFD_CTL_COUNT_SET(count) |
					 TFD_CTL_PAD_SET(pad));

	return 0;
}

/**
 * il3945_hw_txq_free_tfd - Free one TFD, those at index [txq->q.read_ptr]
 *
 * Does NOT advance any indexes
 */
void il3945_hw_txq_free_tfd(struct il_priv *il, struct il_tx_queue *txq)
{
	struct il3945_tfd *tfd_tmp = (struct il3945_tfd *)txq->tfds;
	int index = txq->q.read_ptr;
	struct il3945_tfd *tfd = &tfd_tmp[index];
	struct pci_dev *dev = il->pci_dev;
	int i;
	int counter;

	/* sanity check */
	counter = TFD_CTL_COUNT_GET(le32_to_cpu(tfd->control_flags));
	if (counter > NUM_TFD_CHUNKS) {
		IL_ERR("Too many chunks: %i\n", counter);
		/* @todo issue fatal error, it is quite serious situation */
		return;
	}

	/* Unmap tx_cmd */
	if (counter)
		pci_unmap_single(dev,
				dma_unmap_addr(&txq->meta[index], mapping),
				dma_unmap_len(&txq->meta[index], len),
				PCI_DMA_TODEVICE);

	/* unmap chunks if any */

	for (i = 1; i < counter; i++)
		pci_unmap_single(dev, le32_to_cpu(tfd->tbs[i].addr),
			 le32_to_cpu(tfd->tbs[i].len), PCI_DMA_TODEVICE);

	/* free SKB */
	if (txq->txb) {
		struct sk_buff *skb;

		skb = txq->txb[txq->q.read_ptr].skb;

		/* can be called from irqs-disabled context */
		if (skb) {
			dev_kfree_skb_any(skb);
			txq->txb[txq->q.read_ptr].skb = NULL;
		}
	}
}

/**
 * il3945_hw_build_tx_cmd_rate - Add rate portion to TX_CMD:
 *
*/
void il3945_hw_build_tx_cmd_rate(struct il_priv *il,
				  struct il_device_cmd *cmd,
				  struct ieee80211_tx_info *info,
				  struct ieee80211_hdr *hdr,
				  int sta_id, int tx_id)
{
	u16 hw_value = ieee80211_get_tx_rate(il->hw, info)->hw_value;
	u16 rate_index = min(hw_value & 0xffff, IL_RATE_COUNT_3945);
	u16 rate_mask;
	int rate;
	u8 rts_retry_limit;
	u8 data_retry_limit;
	__le32 tx_flags;
	__le16 fc = hdr->frame_control;
	struct il3945_tx_cmd *tx_cmd = (struct il3945_tx_cmd *)cmd->cmd.payload;

	rate = il3945_rates[rate_index].plcp;
	tx_flags = tx_cmd->tx_flags;

	/* We need to figure out how to get the sta->supp_rates while
	 * in this running context */
	rate_mask = IL_RATES_MASK_3945;

	/* Set retry limit on DATA packets and Probe Responses*/
	if (ieee80211_is_probe_resp(fc))
		data_retry_limit = 3;
	else
		data_retry_limit = IL_DEFAULT_TX_RETRY;
	tx_cmd->data_retry_limit = data_retry_limit;

	if (tx_id >= IWL39_CMD_QUEUE_NUM)
		rts_retry_limit = 3;
	else
		rts_retry_limit = 7;

	if (data_retry_limit < rts_retry_limit)
		rts_retry_limit = data_retry_limit;
	tx_cmd->rts_retry_limit = rts_retry_limit;

	tx_cmd->rate = rate;
	tx_cmd->tx_flags = tx_flags;

	/* OFDM */
	tx_cmd->supp_rates[0] =
	   ((rate_mask & IL_OFDM_RATES_MASK) >> IL_FIRST_OFDM_RATE) & 0xFF;

	/* CCK */
	tx_cmd->supp_rates[1] = (rate_mask & 0xF);

	D_RATE("Tx sta id: %d, rate: %d (plcp), flags: 0x%4X "
		       "cck/ofdm mask: 0x%x/0x%x\n", sta_id,
		       tx_cmd->rate, le32_to_cpu(tx_cmd->tx_flags),
		       tx_cmd->supp_rates[1], tx_cmd->supp_rates[0]);
}

static u8 il3945_sync_sta(struct il_priv *il, int sta_id, u16 tx_rate)
{
	unsigned long flags_spin;
	struct il_station_entry *station;

	if (sta_id == IL_INVALID_STATION)
		return IL_INVALID_STATION;

	spin_lock_irqsave(&il->sta_lock, flags_spin);
	station = &il->stations[sta_id];

	station->sta.sta.modify_mask = STA_MODIFY_TX_RATE_MSK;
	station->sta.rate_n_flags = cpu_to_le16(tx_rate);
	station->sta.mode = STA_CONTROL_MODIFY_MSK;
	il_send_add_sta(il, &station->sta, CMD_ASYNC);
	spin_unlock_irqrestore(&il->sta_lock, flags_spin);

	D_RATE("SCALE sync station %d to rate %d\n",
			sta_id, tx_rate);
	return sta_id;
}

static void il3945_set_pwr_vmain(struct il_priv *il)
{
/*
 * (for documentation purposes)
 * to set power to V_AUX, do

		if (pci_pme_capable(il->pci_dev, PCI_D3cold)) {
			il_set_bits_mask_prph(il, APMG_PS_CTRL_REG,
					APMG_PS_CTRL_VAL_PWR_SRC_VAUX,
					~APMG_PS_CTRL_MSK_PWR_SRC);

			_il_poll_bit(il, CSR_GPIO_IN,
				     CSR_GPIO_IN_VAL_VAUX_PWR_SRC,
				     CSR_GPIO_IN_BIT_AUX_POWER, 5000);
		}
 */

	il_set_bits_mask_prph(il, APMG_PS_CTRL_REG,
			APMG_PS_CTRL_VAL_PWR_SRC_VMAIN,
			~APMG_PS_CTRL_MSK_PWR_SRC);

	_il_poll_bit(il, CSR_GPIO_IN, CSR_GPIO_IN_VAL_VMAIN_PWR_SRC,
		     CSR_GPIO_IN_BIT_AUX_POWER, 5000);	/* uS */
}

static int il3945_rx_init(struct il_priv *il, struct il_rx_queue *rxq)
{
	il_wr(il, FH39_RCSR_RBD_BASE(0), rxq->bd_dma);
	il_wr(il, FH39_RCSR_RPTR_ADDR(0),
					rxq->rb_stts_dma);
	il_wr(il, FH39_RCSR_WPTR(0), 0);
	il_wr(il, FH39_RCSR_CONFIG(0),
		FH39_RCSR_RX_CONFIG_REG_VAL_DMA_CHNL_EN_ENABLE |
		FH39_RCSR_RX_CONFIG_REG_VAL_RDRBD_EN_ENABLE |
		FH39_RCSR_RX_CONFIG_REG_BIT_WR_STTS_EN |
		FH39_RCSR_RX_CONFIG_REG_VAL_MAX_FRAG_SIZE_128 |
		(RX_QUEUE_SIZE_LOG << FH39_RCSR_RX_CONFIG_REG_POS_RBDC_SIZE) |
		FH39_RCSR_RX_CONFIG_REG_VAL_IRQ_DEST_INT_HOST |
		(1 << FH39_RCSR_RX_CONFIG_REG_POS_IRQ_RBTH) |
		FH39_RCSR_RX_CONFIG_REG_VAL_MSG_MODE_FH);

	/* fake read to flush all prev I/O */
	il_rd(il, FH39_RSSR_CTRL);

	return 0;
}

static int il3945_tx_reset(struct il_priv *il)
{

	/* bypass mode */
	il_wr_prph(il, ALM_SCD_MODE_REG, 0x2);

	/* RA 0 is active */
	il_wr_prph(il, ALM_SCD_ARASTAT_REG, 0x01);

	/* all 6 fifo are active */
	il_wr_prph(il, ALM_SCD_TXFACT_REG, 0x3f);

	il_wr_prph(il, ALM_SCD_SBYP_MODE_1_REG, 0x010000);
	il_wr_prph(il, ALM_SCD_SBYP_MODE_2_REG, 0x030002);
	il_wr_prph(il, ALM_SCD_TXF4MF_REG, 0x000004);
	il_wr_prph(il, ALM_SCD_TXF5MF_REG, 0x000005);

	il_wr(il, FH39_TSSR_CBB_BASE,
			     il->_3945.shared_phys);

	il_wr(il, FH39_TSSR_MSG_CONFIG,
		FH39_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TXPD_ON |
		FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_TXPD_ON |
		FH39_TSSR_TX_MSG_CONFIG_REG_VAL_MAX_FRAG_SIZE_128B |
		FH39_TSSR_TX_MSG_CONFIG_REG_VAL_SNOOP_RD_TFD_ON |
		FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RD_CBB_ON |
		FH39_TSSR_TX_MSG_CONFIG_REG_VAL_ORDER_RSP_WAIT_TH |
		FH39_TSSR_TX_MSG_CONFIG_REG_VAL_RSP_WAIT_TH);


	return 0;
}

/**
 * il3945_txq_ctx_reset - Reset TX queue context
 *
 * Destroys all DMA structures and initialize them again
 */
static int il3945_txq_ctx_reset(struct il_priv *il)
{
	int rc;
	int txq_id, slots_num;

	il3945_hw_txq_ctx_free(il);

	/* allocate tx queue structure */
	rc = il_alloc_txq_mem(il);
	if (rc)
		return rc;

	/* Tx CMD queue */
	rc = il3945_tx_reset(il);
	if (rc)
		goto error;

	/* Tx queue(s) */
	for (txq_id = 0; txq_id < il->hw_params.max_txq_num; txq_id++) {
		slots_num = (txq_id == IWL39_CMD_QUEUE_NUM) ?
				TFD_CMD_SLOTS : TFD_TX_CMD_SLOTS;
		rc = il_tx_queue_init(il, &il->txq[txq_id],
						slots_num, txq_id);
		if (rc) {
			IL_ERR("Tx %d queue init failed\n", txq_id);
			goto error;
		}
	}

	return rc;

 error:
	il3945_hw_txq_ctx_free(il);
	return rc;
}


/*
 * Start up 3945's basic functionality after it has been reset
 * (e.g. after platform boot, or shutdown via il_apm_stop())
 * NOTE:  This does not load uCode nor start the embedded processor
 */
static int il3945_apm_init(struct il_priv *il)
{
	int ret = il_apm_init(il);

	/* Clear APMG (NIC's internal power management) interrupts */
	il_wr_prph(il, APMG_RTC_INT_MSK_REG, 0x0);
	il_wr_prph(il, APMG_RTC_INT_STT_REG, 0xFFFFFFFF);

	/* Reset radio chip */
	il_set_bits_prph(il, APMG_PS_CTRL_REG,
				APMG_PS_CTRL_VAL_RESET_REQ);
	udelay(5);
	il_clear_bits_prph(il, APMG_PS_CTRL_REG,
				APMG_PS_CTRL_VAL_RESET_REQ);

	return ret;
}

static void il3945_nic_config(struct il_priv *il)
{
	struct il3945_eeprom *eeprom = (struct il3945_eeprom *)il->eeprom;
	unsigned long flags;
	u8 rev_id = il->pci_dev->revision;

	spin_lock_irqsave(&il->lock, flags);

	/* Determine HW type */
	D_INFO("HW Revision ID = 0x%X\n", rev_id);

	if (rev_id & PCI_CFG_REV_ID_BIT_RTP)
		D_INFO("RTP type\n");
	else if (rev_id & PCI_CFG_REV_ID_BIT_BASIC_SKU) {
		D_INFO("3945 RADIO-MB type\n");
		il_set_bit(il, CSR_HW_IF_CONFIG_REG,
			    CSR39_HW_IF_CONFIG_REG_BIT_3945_MB);
	} else {
		D_INFO("3945 RADIO-MM type\n");
		il_set_bit(il, CSR_HW_IF_CONFIG_REG,
			    CSR39_HW_IF_CONFIG_REG_BIT_3945_MM);
	}

	if (EEPROM_SKU_CAP_OP_MODE_MRC == eeprom->sku_cap) {
		D_INFO("SKU OP mode is mrc\n");
		il_set_bit(il, CSR_HW_IF_CONFIG_REG,
			    CSR39_HW_IF_CONFIG_REG_BIT_SKU_MRC);
	} else
		D_INFO("SKU OP mode is basic\n");

	if ((eeprom->board_revision & 0xF0) == 0xD0) {
		D_INFO("3945ABG revision is 0x%X\n",
			       eeprom->board_revision);
		il_set_bit(il, CSR_HW_IF_CONFIG_REG,
			    CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE);
	} else {
		D_INFO("3945ABG revision is 0x%X\n",
			       eeprom->board_revision);
		il_clear_bit(il, CSR_HW_IF_CONFIG_REG,
			      CSR39_HW_IF_CONFIG_REG_BIT_BOARD_TYPE);
	}

	if (eeprom->almgor_m_version <= 1) {
		il_set_bit(il, CSR_HW_IF_CONFIG_REG,
			    CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_A);
		D_INFO("Card M type A version is 0x%X\n",
			       eeprom->almgor_m_version);
	} else {
		D_INFO("Card M type B version is 0x%X\n",
			       eeprom->almgor_m_version);
		il_set_bit(il, CSR_HW_IF_CONFIG_REG,
			    CSR39_HW_IF_CONFIG_REG_BITS_SILICON_TYPE_B);
	}
	spin_unlock_irqrestore(&il->lock, flags);

	if (eeprom->sku_cap & EEPROM_SKU_CAP_SW_RF_KILL_ENABLE)
		D_RF_KILL("SW RF KILL supported in EEPROM.\n");

	if (eeprom->sku_cap & EEPROM_SKU_CAP_HW_RF_KILL_ENABLE)
		D_RF_KILL("HW RF KILL supported in EEPROM.\n");
}

int il3945_hw_nic_init(struct il_priv *il)
{
	int rc;
	unsigned long flags;
	struct il_rx_queue *rxq = &il->rxq;

	spin_lock_irqsave(&il->lock, flags);
	il->cfg->ops->lib->apm_ops.init(il);
	spin_unlock_irqrestore(&il->lock, flags);

	il3945_set_pwr_vmain(il);

	il->cfg->ops->lib->apm_ops.config(il);

	/* Allocate the RX queue, or reset if it is already allocated */
	if (!rxq->bd) {
		rc = il_rx_queue_alloc(il);
		if (rc) {
			IL_ERR("Unable to initialize Rx queue\n");
			return -ENOMEM;
		}
	} else
		il3945_rx_queue_reset(il, rxq);

	il3945_rx_replenish(il);

	il3945_rx_init(il, rxq);


	/* Look at using this instead:
	rxq->need_update = 1;
	il_rx_queue_update_write_ptr(il, rxq);
	*/

	il_wr(il, FH39_RCSR_WPTR(0), rxq->write & ~7);

	rc = il3945_txq_ctx_reset(il);
	if (rc)
		return rc;

	set_bit(STATUS_INIT, &il->status);

	return 0;
}

/**
 * il3945_hw_txq_ctx_free - Free TXQ Context
 *
 * Destroy all TX DMA queues and structures
 */
void il3945_hw_txq_ctx_free(struct il_priv *il)
{
	int txq_id;

	/* Tx queues */
	if (il->txq)
		for (txq_id = 0; txq_id < il->hw_params.max_txq_num;
		     txq_id++)
			if (txq_id == IWL39_CMD_QUEUE_NUM)
				il_cmd_queue_free(il);
			else
				il_tx_queue_free(il, txq_id);

	/* free tx queue structure */
	il_txq_mem(il);
}

void il3945_hw_txq_ctx_stop(struct il_priv *il)
{
	int txq_id;

	/* stop SCD */
	il_wr_prph(il, ALM_SCD_MODE_REG, 0);
	il_wr_prph(il, ALM_SCD_TXFACT_REG, 0);

	/* reset TFD queues */
	for (txq_id = 0; txq_id < il->hw_params.max_txq_num; txq_id++) {
		il_wr(il, FH39_TCSR_CONFIG(txq_id), 0x0);
		il_poll_bit(il, FH39_TSSR_TX_STATUS,
				FH39_TSSR_TX_STATUS_REG_MSK_CHNL_IDLE(txq_id),
				1000);
	}

	il3945_hw_txq_ctx_free(il);
}

/**
 * il3945_hw_reg_adjust_power_by_temp
 * return index delta into power gain settings table
*/
static int il3945_hw_reg_adjust_power_by_temp(int new_reading, int old_reading)
{
	return (new_reading - old_reading) * (-11) / 100;
}

/**
 * il3945_hw_reg_temp_out_of_range - Keep temperature in sane range
 */
static inline int il3945_hw_reg_temp_out_of_range(int temperature)
{
	return (temperature < -260 || temperature > 25) ? 1 : 0;
}

int il3945_hw_get_temperature(struct il_priv *il)
{
	return _il_rd(il, CSR_UCODE_DRV_GP2);
}

/**
 * il3945_hw_reg_txpower_get_temperature
 * get the current temperature by reading from NIC
*/
static int il3945_hw_reg_txpower_get_temperature(struct il_priv *il)
{
	struct il3945_eeprom *eeprom = (struct il3945_eeprom *)il->eeprom;
	int temperature;

	temperature = il3945_hw_get_temperature(il);

	/* driver's okay range is -260 to +25.
	 *   human readable okay range is 0 to +285 */
	D_INFO("Temperature: %d\n", temperature + IL_TEMP_CONVERT);

	/* handle insane temp reading */
	if (il3945_hw_reg_temp_out_of_range(temperature)) {
		IL_ERR("Error bad temperature value  %d\n", temperature);

		/* if really really hot(?),
		 *   substitute the 3rd band/group's temp measured at factory */
		if (il->last_temperature > 100)
			temperature = eeprom->groups[2].temperature;
		else /* else use most recent "sane" value from driver */
			temperature = il->last_temperature;
	}

	return temperature;	/* raw, not "human readable" */
}

/* Adjust Txpower only if temperature variance is greater than threshold.
 *
 * Both are lower than older versions' 9 degrees */
#define IL_TEMPERATURE_LIMIT_TIMER   6

/**
 * il3945_is_temp_calib_needed - determines if new calibration is needed
 *
 * records new temperature in tx_mgr->temperature.
 * replaces tx_mgr->last_temperature *only* if calib needed
 *    (assumes caller will actually do the calibration!). */
static int il3945_is_temp_calib_needed(struct il_priv *il)
{
	int temp_diff;

	il->temperature = il3945_hw_reg_txpower_get_temperature(il);
	temp_diff = il->temperature - il->last_temperature;

	/* get absolute value */
	if (temp_diff < 0) {
		D_POWER("Getting cooler, delta %d,\n", temp_diff);
		temp_diff = -temp_diff;
	} else if (temp_diff == 0)
		D_POWER("Same temp,\n");
	else
		D_POWER("Getting warmer, delta %d,\n", temp_diff);

	/* if we don't need calibration, *don't* update last_temperature */
	if (temp_diff < IL_TEMPERATURE_LIMIT_TIMER) {
		D_POWER("Timed thermal calib not needed\n");
		return 0;
	}

	D_POWER("Timed thermal calib needed\n");

	/* assume that caller will actually do calib ...
	 *   update the "last temperature" value */
	il->last_temperature = il->temperature;
	return 1;
}

#define IL_MAX_GAIN_ENTRIES 78
#define IL_CCK_FROM_OFDM_POWER_DIFF  -5
#define IL_CCK_FROM_OFDM_INDEX_DIFF (10)

/* radio and DSP power table, each step is 1/2 dB.
 * 1st number is for RF analog gain, 2nd number is for DSP pre-DAC gain. */
static struct il3945_tx_power power_gain_table[2][IL_MAX_GAIN_ENTRIES] = {
	{
	 {251, 127},		/* 2.4 GHz, highest power */
	 {251, 127},
	 {251, 127},
	 {251, 127},
	 {251, 125},
	 {251, 110},
	 {251, 105},
	 {251, 98},
	 {187, 125},
	 {187, 115},
	 {187, 108},
	 {187, 99},
	 {243, 119},
	 {243, 111},
	 {243, 105},
	 {243, 97},
	 {243, 92},
	 {211, 106},
	 {211, 100},
	 {179, 120},
	 {179, 113},
	 {179, 107},
	 {147, 125},
	 {147, 119},
	 {147, 112},
	 {147, 106},
	 {147, 101},
	 {147, 97},
	 {147, 91},
	 {115, 107},
	 {235, 121},
	 {235, 115},
	 {235, 109},
	 {203, 127},
	 {203, 121},
	 {203, 115},
	 {203, 108},
	 {203, 102},
	 {203, 96},
	 {203, 92},
	 {171, 110},
	 {171, 104},
	 {171, 98},
	 {139, 116},
	 {227, 125},
	 {227, 119},
	 {227, 113},
	 {227, 107},
	 {227, 101},
	 {227, 96},
	 {195, 113},
	 {195, 106},
	 {195, 102},
	 {195, 95},
	 {163, 113},
	 {163, 106},
	 {163, 102},
	 {163, 95},
	 {131, 113},
	 {131, 106},
	 {131, 102},
	 {131, 95},
	 {99, 113},
	 {99, 106},
	 {99, 102},
	 {99, 95},
	 {67, 113},
	 {67, 106},
	 {67, 102},
	 {67, 95},
	 {35, 113},
	 {35, 106},
	 {35, 102},
	 {35, 95},
	 {3, 113},
	 {3, 106},
	 {3, 102},
	 {3, 95} },		/* 2.4 GHz, lowest power */
	{
	 {251, 127},		/* 5.x GHz, highest power */
	 {251, 120},
	 {251, 114},
	 {219, 119},
	 {219, 101},
	 {187, 113},
	 {187, 102},
	 {155, 114},
	 {155, 103},
	 {123, 117},
	 {123, 107},
	 {123, 99},
	 {123, 92},
	 {91, 108},
	 {59, 125},
	 {59, 118},
	 {59, 109},
	 {59, 102},
	 {59, 96},
	 {59, 90},
	 {27, 104},
	 {27, 98},
	 {27, 92},
	 {115, 118},
	 {115, 111},
	 {115, 104},
	 {83, 126},
	 {83, 121},
	 {83, 113},
	 {83, 105},
	 {83, 99},
	 {51, 118},
	 {51, 111},
	 {51, 104},
	 {51, 98},
	 {19, 116},
	 {19, 109},
	 {19, 102},
	 {19, 98},
	 {19, 93},
	 {171, 113},
	 {171, 107},
	 {171, 99},
	 {139, 120},
	 {139, 113},
	 {139, 107},
	 {139, 99},
	 {107, 120},
	 {107, 113},
	 {107, 107},
	 {107, 99},
	 {75, 120},
	 {75, 113},
	 {75, 107},
	 {75, 99},
	 {43, 120},
	 {43, 113},
	 {43, 107},
	 {43, 99},
	 {11, 120},
	 {11, 113},
	 {11, 107},
	 {11, 99},
	 {131, 107},
	 {131, 99},
	 {99, 120},
	 {99, 113},
	 {99, 107},
	 {99, 99},
	 {67, 120},
	 {67, 113},
	 {67, 107},
	 {67, 99},
	 {35, 120},
	 {35, 113},
	 {35, 107},
	 {35, 99},
	 {3, 120} }		/* 5.x GHz, lowest power */
};

static inline u8 il3945_hw_reg_fix_power_index(int index)
{
	if (index < 0)
		return 0;
	if (index >= IL_MAX_GAIN_ENTRIES)
		return IL_MAX_GAIN_ENTRIES - 1;
	return (u8) index;
}

/* Kick off thermal recalibration check every 60 seconds */
#define REG_RECALIB_PERIOD (60)

/**
 * il3945_hw_reg_set_scan_power - Set Tx power for scan probe requests
 *
 * Set (in our channel info database) the direct scan Tx power for 1 Mbit (CCK)
 * or 6 Mbit (OFDM) rates.
 */
static void il3945_hw_reg_set_scan_power(struct il_priv *il, u32 scan_tbl_index,
			       s32 rate_index, const s8 *clip_pwrs,
			       struct il_channel_info *ch_info,
			       int band_index)
{
	struct il3945_scan_power_info *scan_power_info;
	s8 power;
	u8 power_index;

	scan_power_info = &ch_info->scan_pwr_info[scan_tbl_index];

	/* use this channel group's 6Mbit clipping/saturation pwr,
	 *   but cap at regulatory scan power restriction (set during init
	 *   based on eeprom channel data) for this channel.  */
	power = min(ch_info->scan_power, clip_pwrs[IL_RATE_6M_INDEX_TABLE]);

	power = min(power, il->tx_power_user_lmt);
	scan_power_info->requested_power = power;

	/* find difference between new scan *power* and current "normal"
	 *   Tx *power* for 6Mb.  Use this difference (x2) to adjust the
	 *   current "normal" temperature-compensated Tx power *index* for
	 *   this rate (1Mb or 6Mb) to yield new temp-compensated scan power
	 *   *index*. */
	power_index = ch_info->power_info[rate_index].power_table_index
	    - (power - ch_info->power_info
	       [IL_RATE_6M_INDEX_TABLE].requested_power) * 2;

	/* store reference index that we use when adjusting *all* scan
	 *   powers.  So we can accommodate user (all channel) or spectrum
	 *   management (single channel) power changes "between" temperature
	 *   feedback compensation procedures.
	 * don't force fit this reference index into gain table; it may be a
	 *   negative number.  This will help avoid errors when we're at
	 *   the lower bounds (highest gains, for warmest temperatures)
	 *   of the table. */

	/* don't exceed table bounds for "real" setting */
	power_index = il3945_hw_reg_fix_power_index(power_index);

	scan_power_info->power_table_index = power_index;
	scan_power_info->tpc.tx_gain =
	    power_gain_table[band_index][power_index].tx_gain;
	scan_power_info->tpc.dsp_atten =
	    power_gain_table[band_index][power_index].dsp_atten;
}

/**
 * il3945_send_tx_power - fill in Tx Power command with gain settings
 *
 * Configures power settings for all rates for the current channel,
 * using values from channel info struct, and send to NIC
 */
static int il3945_send_tx_power(struct il_priv *il)
{
	int rate_idx, i;
	const struct il_channel_info *ch_info = NULL;
	struct il3945_txpowertable_cmd txpower = {
		.channel = il->contexts[IL_RXON_CTX_BSS].active.channel,
	};
	u16 chan;

	if (WARN_ONCE(test_bit(STATUS_SCAN_HW, &il->status),
		      "TX Power requested while scanning!\n"))
		return -EAGAIN;

	chan = le16_to_cpu(il->contexts[IL_RXON_CTX_BSS].active.channel);

	txpower.band = (il->band == IEEE80211_BAND_5GHZ) ? 0 : 1;
	ch_info = il_get_channel_info(il, il->band, chan);
	if (!ch_info) {
		IL_ERR(
			"Failed to get channel info for channel %d [%d]\n",
			chan, il->band);
		return -EINVAL;
	}

	if (!il_is_channel_valid(ch_info)) {
		D_POWER("Not calling TX_PWR_TABLE_CMD on "
				"non-Tx channel.\n");
		return 0;
	}

	/* fill cmd with power settings for all rates for current channel */
	/* Fill OFDM rate */
	for (rate_idx = IL_FIRST_OFDM_RATE, i = 0;
	     rate_idx <= IWL39_LAST_OFDM_RATE; rate_idx++, i++) {

		txpower.power[i].tpc = ch_info->power_info[i].tpc;
		txpower.power[i].rate = il3945_rates[rate_idx].plcp;

		D_POWER("ch %d:%d rf %d dsp %3d rate code 0x%02x\n",
				le16_to_cpu(txpower.channel),
				txpower.band,
				txpower.power[i].tpc.tx_gain,
				txpower.power[i].tpc.dsp_atten,
				txpower.power[i].rate);
	}
	/* Fill CCK rates */
	for (rate_idx = IL_FIRST_CCK_RATE;
	     rate_idx <= IL_LAST_CCK_RATE; rate_idx++, i++) {
		txpower.power[i].tpc = ch_info->power_info[i].tpc;
		txpower.power[i].rate = il3945_rates[rate_idx].plcp;

		D_POWER("ch %d:%d rf %d dsp %3d rate code 0x%02x\n",
				le16_to_cpu(txpower.channel),
				txpower.band,
				txpower.power[i].tpc.tx_gain,
				txpower.power[i].tpc.dsp_atten,
				txpower.power[i].rate);
	}

	return il_send_cmd_pdu(il, REPLY_TX_PWR_TABLE_CMD,
				sizeof(struct il3945_txpowertable_cmd),
				&txpower);

}

/**
 * il3945_hw_reg_set_new_power - Configures power tables at new levels
 * @ch_info: Channel to update.  Uses power_info.requested_power.
 *
 * Replace requested_power and base_power_index ch_info fields for
 * one channel.
 *
 * Called if user or spectrum management changes power preferences.
 * Takes into account h/w and modulation limitations (clip power).
 *
 * This does *not* send anything to NIC, just sets up ch_info for one channel.
 *
 * NOTE: reg_compensate_for_temperature_dif() *must* be run after this to
 *	 properly fill out the scan powers, and actual h/w gain settings,
 *	 and send changes to NIC
 */
static int il3945_hw_reg_set_new_power(struct il_priv *il,
			     struct il_channel_info *ch_info)
{
	struct il3945_channel_power_info *power_info;
	int power_changed = 0;
	int i;
	const s8 *clip_pwrs;
	int power;

	/* Get this chnlgrp's rate-to-max/clip-powers table */
	clip_pwrs = il->_3945.clip_groups[ch_info->group_index].clip_powers;

	/* Get this channel's rate-to-current-power settings table */
	power_info = ch_info->power_info;

	/* update OFDM Txpower settings */
	for (i = IL_RATE_6M_INDEX_TABLE; i <= IL_RATE_54M_INDEX_TABLE;
	     i++, ++power_info) {
		int delta_idx;

		/* limit new power to be no more than h/w capability */
		power = min(ch_info->curr_txpow, clip_pwrs[i]);
		if (power == power_info->requested_power)
			continue;

		/* find difference between old and new requested powers,
		 *    update base (non-temp-compensated) power index */
		delta_idx = (power - power_info->requested_power) * 2;
		power_info->base_power_index -= delta_idx;

		/* save new requested power value */
		power_info->requested_power = power;

		power_changed = 1;
	}

	/* update CCK Txpower settings, based on OFDM 12M setting ...
	 *    ... all CCK power settings for a given channel are the *same*. */
	if (power_changed) {
		power =
		    ch_info->power_info[IL_RATE_12M_INDEX_TABLE].
		    requested_power + IL_CCK_FROM_OFDM_POWER_DIFF;

		/* do all CCK rates' il3945_channel_power_info structures */
		for (i = IL_RATE_1M_INDEX_TABLE; i <= IL_RATE_11M_INDEX_TABLE; i++) {
			power_info->requested_power = power;
			power_info->base_power_index =
			    ch_info->power_info[IL_RATE_12M_INDEX_TABLE].
			    base_power_index + IL_CCK_FROM_OFDM_INDEX_DIFF;
			++power_info;
		}
	}

	return 0;
}

/**
 * il3945_hw_reg_get_ch_txpower_limit - returns new power limit for channel
 *
 * NOTE: Returned power limit may be less (but not more) than requested,
 *	 based strictly on regulatory (eeprom and spectrum mgt) limitations
 *	 (no consideration for h/w clipping limitations).
 */
static int il3945_hw_reg_get_ch_txpower_limit(struct il_channel_info *ch_info)
{
	s8 max_power;

#if 0
	/* if we're using TGd limits, use lower of TGd or EEPROM */
	if (ch_info->tgd_data.max_power != 0)
		max_power = min(ch_info->tgd_data.max_power,
				ch_info->eeprom.max_power_avg);

	/* else just use EEPROM limits */
	else
#endif
		max_power = ch_info->eeprom.max_power_avg;

	return min(max_power, ch_info->max_power_avg);
}

/**
 * il3945_hw_reg_comp_txpower_temp - Compensate for temperature
 *
 * Compensate txpower settings of *all* channels for temperature.
 * This only accounts for the difference between current temperature
 *   and the factory calibration temperatures, and bases the new settings
 *   on the channel's base_power_index.
 *
 * If RxOn is "associated", this sends the new Txpower to NIC!
 */
static int il3945_hw_reg_comp_txpower_temp(struct il_priv *il)
{
	struct il_channel_info *ch_info = NULL;
	struct il3945_eeprom *eeprom = (struct il3945_eeprom *)il->eeprom;
	int delta_index;
	const s8 *clip_pwrs; /* array of h/w max power levels for each rate */
	u8 a_band;
	u8 rate_index;
	u8 scan_tbl_index;
	u8 i;
	int ref_temp;
	int temperature = il->temperature;

	if (il->disable_tx_power_cal ||
	    test_bit(STATUS_SCANNING, &il->status)) {
		/* do not perform tx power calibration */
		return 0;
	}
	/* set up new Tx power info for each and every channel, 2.4 and 5.x */
	for (i = 0; i < il->channel_count; i++) {
		ch_info = &il->channel_info[i];
		a_band = il_is_channel_a_band(ch_info);

		/* Get this chnlgrp's factory calibration temperature */
		ref_temp = (s16)eeprom->groups[ch_info->group_index].
		    temperature;

		/* get power index adjustment based on current and factory
		 * temps */
		delta_index = il3945_hw_reg_adjust_power_by_temp(temperature,
							      ref_temp);

		/* set tx power value for all rates, OFDM and CCK */
		for (rate_index = 0; rate_index < IL_RATE_COUNT_3945;
		     rate_index++) {
			int power_idx =
			    ch_info->power_info[rate_index].base_power_index;

			/* temperature compensate */
			power_idx += delta_index;

			/* stay within table range */
			power_idx = il3945_hw_reg_fix_power_index(power_idx);
			ch_info->power_info[rate_index].
			    power_table_index = (u8) power_idx;
			ch_info->power_info[rate_index].tpc =
			    power_gain_table[a_band][power_idx];
		}

		/* Get this chnlgrp's rate-to-max/clip-powers table */
		clip_pwrs = il->_3945.clip_groups[ch_info->group_index].clip_powers;

		/* set scan tx power, 1Mbit for CCK, 6Mbit for OFDM */
		for (scan_tbl_index = 0;
		     scan_tbl_index < IL_NUM_SCAN_RATES; scan_tbl_index++) {
			s32 actual_index = (scan_tbl_index == 0) ?
			    IL_RATE_1M_INDEX_TABLE : IL_RATE_6M_INDEX_TABLE;
			il3945_hw_reg_set_scan_power(il, scan_tbl_index,
					   actual_index, clip_pwrs,
					   ch_info, a_band);
		}
	}

	/* send Txpower command for current channel to ucode */
	return il->cfg->ops->lib->send_tx_power(il);
}

int il3945_hw_reg_set_txpower(struct il_priv *il, s8 power)
{
	struct il_channel_info *ch_info;
	s8 max_power;
	u8 a_band;
	u8 i;

	if (il->tx_power_user_lmt == power) {
		D_POWER("Requested Tx power same as current "
				"limit: %ddBm.\n", power);
		return 0;
	}

	D_POWER("Setting upper limit clamp to %ddBm.\n", power);
	il->tx_power_user_lmt = power;

	/* set up new Tx powers for each and every channel, 2.4 and 5.x */

	for (i = 0; i < il->channel_count; i++) {
		ch_info = &il->channel_info[i];
		a_band = il_is_channel_a_band(ch_info);

		/* find minimum power of all user and regulatory constraints
		 *    (does not consider h/w clipping limitations) */
		max_power = il3945_hw_reg_get_ch_txpower_limit(ch_info);
		max_power = min(power, max_power);
		if (max_power != ch_info->curr_txpow) {
			ch_info->curr_txpow = max_power;

			/* this considers the h/w clipping limitations */
			il3945_hw_reg_set_new_power(il, ch_info);
		}
	}

	/* update txpower settings for all channels,
	 *   send to NIC if associated. */
	il3945_is_temp_calib_needed(il);
	il3945_hw_reg_comp_txpower_temp(il);

	return 0;
}

static int il3945_send_rxon_assoc(struct il_priv *il,
				   struct il_rxon_context *ctx)
{
	int rc = 0;
	struct il_rx_packet *pkt;
	struct il3945_rxon_assoc_cmd rxon_assoc;
	struct il_host_cmd cmd = {
		.id = REPLY_RXON_ASSOC,
		.len = sizeof(rxon_assoc),
		.flags = CMD_WANT_SKB,
		.data = &rxon_assoc,
	};
	const struct il_rxon_cmd *rxon1 = &ctx->staging;
	const struct il_rxon_cmd *rxon2 = &ctx->active;

	if (rxon1->flags == rxon2->flags &&
	    rxon1->filter_flags == rxon2->filter_flags &&
	    rxon1->cck_basic_rates == rxon2->cck_basic_rates &&
	    rxon1->ofdm_basic_rates == rxon2->ofdm_basic_rates) {
		D_INFO("Using current RXON_ASSOC.  Not resending.\n");
		return 0;
	}

	rxon_assoc.flags = ctx->staging.flags;
	rxon_assoc.filter_flags = ctx->staging.filter_flags;
	rxon_assoc.ofdm_basic_rates = ctx->staging.ofdm_basic_rates;
	rxon_assoc.cck_basic_rates = ctx->staging.cck_basic_rates;
	rxon_assoc.reserved = 0;

	rc = il_send_cmd_sync(il, &cmd);
	if (rc)
		return rc;

	pkt = (struct il_rx_packet *)cmd.reply_page;
	if (pkt->hdr.flags & IL_CMD_FAILED_MSK) {
		IL_ERR("Bad return from REPLY_RXON_ASSOC command\n");
		rc = -EIO;
	}

	il_free_pages(il, cmd.reply_page);

	return rc;
}

/**
 * il3945_commit_rxon - commit staging_rxon to hardware
 *
 * The RXON command in staging_rxon is committed to the hardware and
 * the active_rxon structure is updated with the new data.  This
 * function correctly transitions out of the RXON_ASSOC_MSK state if
 * a HW tune is required based on the RXON structure changes.
 */
int il3945_commit_rxon(struct il_priv *il, struct il_rxon_context *ctx)
{
	/* cast away the const for active_rxon in this function */
	struct il3945_rxon_cmd *active_rxon = (void *)&ctx->active;
	struct il3945_rxon_cmd *staging_rxon = (void *)&ctx->staging;
	int rc = 0;
	bool new_assoc = !!(staging_rxon->filter_flags & RXON_FILTER_ASSOC_MSK);

	if (test_bit(STATUS_EXIT_PENDING, &il->status))
		return -EINVAL;

	if (!il_is_alive(il))
		return -1;

	/* always get timestamp with Rx frame */
	staging_rxon->flags |= RXON_FLG_TSF2HOST_MSK;

	/* select antenna */
	staging_rxon->flags &=
	    ~(RXON_FLG_DIS_DIV_MSK | RXON_FLG_ANT_SEL_MSK);
	staging_rxon->flags |= il3945_get_antenna_flags(il);

	rc = il_check_rxon_cmd(il, ctx);
	if (rc) {
		IL_ERR("Invalid RXON configuration.  Not committing.\n");
		return -EINVAL;
	}

	/* If we don't need to send a full RXON, we can use
	 * il3945_rxon_assoc_cmd which is used to reconfigure filter
	 * and other flags for the current radio configuration. */
	if (!il_full_rxon_required(il,
			&il->contexts[IL_RXON_CTX_BSS])) {
		rc = il_send_rxon_assoc(il,
					 &il->contexts[IL_RXON_CTX_BSS]);
		if (rc) {
			IL_ERR("Error setting RXON_ASSOC "
				  "configuration (%d).\n", rc);
			return rc;
		}

		memcpy(active_rxon, staging_rxon, sizeof(*active_rxon));
		/*
		 * We do not commit tx power settings while channel changing,
		 * do it now if tx power changed.
		 */
		il_set_tx_power(il, il->tx_power_next, false);
		return 0;
	}

	/* If we are currently associated and the new config requires
	 * an RXON_ASSOC and the new config wants the associated mask enabled,
	 * we must clear the associated from the active configuration
	 * before we apply the new config */
	if (il_is_associated(il, IL_RXON_CTX_BSS) && new_assoc) {
		D_INFO("Toggling associated bit on current RXON\n");
		active_rxon->filter_flags &= ~RXON_FILTER_ASSOC_MSK;

		/*
		 * reserved4 and 5 could have been filled by the iwlcore code.
		 * Let's clear them before pushing to the 3945.
		 */
		active_rxon->reserved4 = 0;
		active_rxon->reserved5 = 0;
		rc = il_send_cmd_pdu(il, REPLY_RXON,
				      sizeof(struct il3945_rxon_cmd),
				      &il->contexts[IL_RXON_CTX_BSS].active);

		/* If the mask clearing failed then we set
		 * active_rxon back to what it was previously */
		if (rc) {
			active_rxon->filter_flags |= RXON_FILTER_ASSOC_MSK;
			IL_ERR("Error clearing ASSOC_MSK on current "
				  "configuration (%d).\n", rc);
			return rc;
		}
		il_clear_ucode_stations(il,
					 &il->contexts[IL_RXON_CTX_BSS]);
		il_restore_stations(il,
					 &il->contexts[IL_RXON_CTX_BSS]);
	}

	D_INFO("Sending RXON\n"
		       "* with%s RXON_FILTER_ASSOC_MSK\n"
		       "* channel = %d\n"
		       "* bssid = %pM\n",
		       (new_assoc ? "" : "out"),
		       le16_to_cpu(staging_rxon->channel),
		       staging_rxon->bssid_addr);

	/*
	 * reserved4 and 5 could have been filled by the iwlcore code.
	 * Let's clear them before pushing to the 3945.
	 */
	staging_rxon->reserved4 = 0;
	staging_rxon->reserved5 = 0;

	il_set_rxon_hwcrypto(il, ctx, !il3945_mod_params.sw_crypto);

	/* Apply the new configuration */
	rc = il_send_cmd_pdu(il, REPLY_RXON,
			      sizeof(struct il3945_rxon_cmd),
			      staging_rxon);
	if (rc) {
		IL_ERR("Error setting new configuration (%d).\n", rc);
		return rc;
	}

	memcpy(active_rxon, staging_rxon, sizeof(*active_rxon));

	if (!new_assoc) {
		il_clear_ucode_stations(il,
					 &il->contexts[IL_RXON_CTX_BSS]);
		il_restore_stations(il,
					&il->contexts[IL_RXON_CTX_BSS]);
	}

	/* If we issue a new RXON command which required a tune then we must
	 * send a new TXPOWER command or we won't be able to Tx any frames */
	rc = il_set_tx_power(il, il->tx_power_next, true);
	if (rc) {
		IL_ERR("Error setting Tx power (%d).\n", rc);
		return rc;
	}

	/* Init the hardware's rate fallback order based on the band */
	rc = il3945_init_hw_rate_table(il);
	if (rc) {
		IL_ERR("Error setting HW rate table: %02X\n", rc);
		return -EIO;
	}

	return 0;
}

/**
 * il3945_reg_txpower_periodic -  called when time to check our temperature.
 *
 * -- reset periodic timer
 * -- see if temp has changed enough to warrant re-calibration ... if so:
 *     -- correct coeffs for temp (can reset temp timer)
 *     -- save this temp as "last",
 *     -- send new set of gain settings to NIC
 * NOTE:  This should continue working, even when we're not associated,
 *   so we can keep our internal table of scan powers current. */
void il3945_reg_txpower_periodic(struct il_priv *il)
{
	/* This will kick in the "brute force"
	 * il3945_hw_reg_comp_txpower_temp() below */
	if (!il3945_is_temp_calib_needed(il))
		goto reschedule;

	/* Set up a new set of temp-adjusted TxPowers, send to NIC.
	 * This is based *only* on current temperature,
	 * ignoring any previous power measurements */
	il3945_hw_reg_comp_txpower_temp(il);

 reschedule:
	queue_delayed_work(il->workqueue,
			   &il->_3945.thermal_periodic, REG_RECALIB_PERIOD * HZ);
}

static void il3945_bg_reg_txpower_periodic(struct work_struct *work)
{
	struct il_priv *il = container_of(work, struct il_priv,
					     _3945.thermal_periodic.work);

	if (test_bit(STATUS_EXIT_PENDING, &il->status))
		return;

	mutex_lock(&il->mutex);
	il3945_reg_txpower_periodic(il);
	mutex_unlock(&il->mutex);
}

/**
 * il3945_hw_reg_get_ch_grp_index - find the channel-group index (0-4)
 * 				   for the channel.
 *
 * This function is used when initializing channel-info structs.
 *
 * NOTE: These channel groups do *NOT* match the bands above!
 *	 These channel groups are based on factory-tested channels;
 *	 on A-band, EEPROM's "group frequency" entries represent the top
 *	 channel in each group 1-4.  Group 5 All B/G channels are in group 0.
 */
static u16 il3945_hw_reg_get_ch_grp_index(struct il_priv *il,
				       const struct il_channel_info *ch_info)
{
	struct il3945_eeprom *eeprom = (struct il3945_eeprom *)il->eeprom;
	struct il3945_eeprom_txpower_group *ch_grp = &eeprom->groups[0];
	u8 group;
	u16 group_index = 0;	/* based on factory calib frequencies */
	u8 grp_channel;

	/* Find the group index for the channel ... don't use index 1(?) */
	if (il_is_channel_a_band(ch_info)) {
		for (group = 1; group < 5; group++) {
			grp_channel = ch_grp[group].group_channel;
			if (ch_info->channel <= grp_channel) {
				group_index = group;
				break;
			}
		}
		/* group 4 has a few channels *above* its factory cal freq */
		if (group == 5)
			group_index = 4;
	} else
		group_index = 0;	/* 2.4 GHz, group 0 */

	D_POWER("Chnl %d mapped to grp %d\n", ch_info->channel,
			group_index);
	return group_index;
}

/**
 * il3945_hw_reg_get_matched_power_index - Interpolate to get nominal index
 *
 * Interpolate to get nominal (i.e. at factory calibration temperature) index
 *   into radio/DSP gain settings table for requested power.
 */
static int il3945_hw_reg_get_matched_power_index(struct il_priv *il,
				       s8 requested_power,
				       s32 setting_index, s32 *new_index)
{
	const struct il3945_eeprom_txpower_group *chnl_grp = NULL;
	struct il3945_eeprom *eeprom = (struct il3945_eeprom *)il->eeprom;
	s32 index0, index1;
	s32 power = 2 * requested_power;
	s32 i;
	const struct il3945_eeprom_txpower_sample *samples;
	s32 gains0, gains1;
	s32 res;
	s32 denominator;

	chnl_grp = &eeprom->groups[setting_index];
	samples = chnl_grp->samples;
	for (i = 0; i < 5; i++) {
		if (power == samples[i].power) {
			*new_index = samples[i].gain_index;
			return 0;
		}
	}

	if (power > samples[1].power) {
		index0 = 0;
		index1 = 1;
	} else if (power > samples[2].power) {
		index0 = 1;
		index1 = 2;
	} else if (power > samples[3].power) {
		index0 = 2;
		index1 = 3;
	} else {
		index0 = 3;
		index1 = 4;
	}

	denominator = (s32) samples[index1].power - (s32) samples[index0].power;
	if (denominator == 0)
		return -EINVAL;
	gains0 = (s32) samples[index0].gain_index * (1 << 19);
	gains1 = (s32) samples[index1].gain_index * (1 << 19);
	res = gains0 + (gains1 - gains0) *
	    ((s32) power - (s32) samples[index0].power) / denominator +
	    (1 << 18);
	*new_index = res >> 19;
	return 0;
}

static void il3945_hw_reg_init_channel_groups(struct il_priv *il)
{
	u32 i;
	s32 rate_index;
	struct il3945_eeprom *eeprom = (struct il3945_eeprom *)il->eeprom;
	const struct il3945_eeprom_txpower_group *group;

	D_POWER("Initializing factory calib info from EEPROM\n");

	for (i = 0; i < IL_NUM_TX_CALIB_GROUPS; i++) {
		s8 *clip_pwrs;	/* table of power levels for each rate */
		s8 satur_pwr;	/* saturation power for each chnl group */
		group = &eeprom->groups[i];

		/* sanity check on factory saturation power value */
		if (group->saturation_power < 40) {
			IL_WARN("Error: saturation power is %d, "
				    "less than minimum expected 40\n",
				    group->saturation_power);
			return;
		}

		/*
		 * Derive requested power levels for each rate, based on
		 *   hardware capabilities (saturation power for band).
		 * Basic value is 3dB down from saturation, with further
		 *   power reductions for highest 3 data rates.  These
		 *   backoffs provide headroom for high rate modulation
		 *   power peaks, without too much distortion (clipping).
		 */
		/* we'll fill in this array with h/w max power levels */
		clip_pwrs = (s8 *) il->_3945.clip_groups[i].clip_powers;

		/* divide factory saturation power by 2 to find -3dB level */
		satur_pwr = (s8) (group->saturation_power >> 1);

		/* fill in channel group's nominal powers for each rate */
		for (rate_index = 0;
		     rate_index < IL_RATE_COUNT_3945; rate_index++, clip_pwrs++) {
			switch (rate_index) {
			case IL_RATE_36M_INDEX_TABLE:
				if (i == 0)	/* B/G */
					*clip_pwrs = satur_pwr;
				else	/* A */
					*clip_pwrs = satur_pwr - 5;
				break;
			case IL_RATE_48M_INDEX_TABLE:
				if (i == 0)
					*clip_pwrs = satur_pwr - 7;
				else
					*clip_pwrs = satur_pwr - 10;
				break;
			case IL_RATE_54M_INDEX_TABLE:
				if (i == 0)
					*clip_pwrs = satur_pwr - 9;
				else
					*clip_pwrs = satur_pwr - 12;
				break;
			default:
				*clip_pwrs = satur_pwr;
				break;
			}
		}
	}
}

/**
 * il3945_txpower_set_from_eeprom - Set channel power info based on EEPROM
 *
 * Second pass (during init) to set up il->channel_info
 *
 * Set up Tx-power settings in our channel info database for each VALID
 * (for this geo/SKU) channel, at all Tx data rates, based on eeprom values
 * and current temperature.
 *
 * Since this is based on current temperature (at init time), these values may
 * not be valid for very long, but it gives us a starting/default point,
 * and allows us to active (i.e. using Tx) scan.
 *
 * This does *not* write values to NIC, just sets up our internal table.
 */
int il3945_txpower_set_from_eeprom(struct il_priv *il)
{
	struct il_channel_info *ch_info = NULL;
	struct il3945_channel_power_info *pwr_info;
	struct il3945_eeprom *eeprom = (struct il3945_eeprom *)il->eeprom;
	int delta_index;
	u8 rate_index;
	u8 scan_tbl_index;
	const s8 *clip_pwrs;	/* array of power levels for each rate */
	u8 gain, dsp_atten;
	s8 power;
	u8 pwr_index, base_pwr_index, a_band;
	u8 i;
	int temperature;

	/* save temperature reference,
	 *   so we can determine next time to calibrate */
	temperature = il3945_hw_reg_txpower_get_temperature(il);
	il->last_temperature = temperature;

	il3945_hw_reg_init_channel_groups(il);

	/* initialize Tx power info for each and every channel, 2.4 and 5.x */
	for (i = 0, ch_info = il->channel_info; i < il->channel_count;
	     i++, ch_info++) {
		a_band = il_is_channel_a_band(ch_info);
		if (!il_is_channel_valid(ch_info))
			continue;

		/* find this channel's channel group (*not* "band") index */
		ch_info->group_index =
			il3945_hw_reg_get_ch_grp_index(il, ch_info);

		/* Get this chnlgrp's rate->max/clip-powers table */
		clip_pwrs = il->_3945.clip_groups[ch_info->group_index].clip_powers;

		/* calculate power index *adjustment* value according to
		 *  diff between current temperature and factory temperature */
		delta_index = il3945_hw_reg_adjust_power_by_temp(temperature,
				eeprom->groups[ch_info->group_index].
				temperature);

		D_POWER("Delta index for channel %d: %d [%d]\n",
				ch_info->channel, delta_index, temperature +
				IL_TEMP_CONVERT);

		/* set tx power value for all OFDM rates */
		for (rate_index = 0; rate_index < IL_OFDM_RATES;
		     rate_index++) {
			s32 uninitialized_var(power_idx);
			int rc;

			/* use channel group's clip-power table,
			 *   but don't exceed channel's max power */
			s8 pwr = min(ch_info->max_power_avg,
				     clip_pwrs[rate_index]);

			pwr_info = &ch_info->power_info[rate_index];

			/* get base (i.e. at factory-measured temperature)
			 *    power table index for this rate's power */
			rc = il3945_hw_reg_get_matched_power_index(il, pwr,
							 ch_info->group_index,
							 &power_idx);
			if (rc) {
				IL_ERR("Invalid power index\n");
				return rc;
			}
			pwr_info->base_power_index = (u8) power_idx;

			/* temperature compensate */
			power_idx += delta_index;

			/* stay within range of gain table */
			power_idx = il3945_hw_reg_fix_power_index(power_idx);

			/* fill 1 OFDM rate's il3945_channel_power_info struct */
			pwr_info->requested_power = pwr;
			pwr_info->power_table_index = (u8) power_idx;
			pwr_info->tpc.tx_gain =
			    power_gain_table[a_band][power_idx].tx_gain;
			pwr_info->tpc.dsp_atten =
			    power_gain_table[a_band][power_idx].dsp_atten;
		}

		/* set tx power for CCK rates, based on OFDM 12 Mbit settings*/
		pwr_info = &ch_info->power_info[IL_RATE_12M_INDEX_TABLE];
		power = pwr_info->requested_power +
			IL_CCK_FROM_OFDM_POWER_DIFF;
		pwr_index = pwr_info->power_table_index +
			IL_CCK_FROM_OFDM_INDEX_DIFF;
		base_pwr_index = pwr_info->base_power_index +
			IL_CCK_FROM_OFDM_INDEX_DIFF;

		/* stay within table range */
		pwr_index = il3945_hw_reg_fix_power_index(pwr_index);
		gain = power_gain_table[a_band][pwr_index].tx_gain;
		dsp_atten = power_gain_table[a_band][pwr_index].dsp_atten;

		/* fill each CCK rate's il3945_channel_power_info structure
		 * NOTE:  All CCK-rate Txpwrs are the same for a given chnl!
		 * NOTE:  CCK rates start at end of OFDM rates! */
		for (rate_index = 0;
		     rate_index < IL_CCK_RATES; rate_index++) {
			pwr_info = &ch_info->power_info[rate_index+IL_OFDM_RATES];
			pwr_info->requested_power = power;
			pwr_info->power_table_index = pwr_index;
			pwr_info->base_power_index = base_pwr_index;
			pwr_info->tpc.tx_gain = gain;
			pwr_info->tpc.dsp_atten = dsp_atten;
		}

		/* set scan tx power, 1Mbit for CCK, 6Mbit for OFDM */
		for (scan_tbl_index = 0;
		     scan_tbl_index < IL_NUM_SCAN_RATES; scan_tbl_index++) {
			s32 actual_index = (scan_tbl_index == 0) ?
				IL_RATE_1M_INDEX_TABLE : IL_RATE_6M_INDEX_TABLE;
			il3945_hw_reg_set_scan_power(il, scan_tbl_index,
				actual_index, clip_pwrs, ch_info, a_band);
		}
	}

	return 0;
}

int il3945_hw_rxq_stop(struct il_priv *il)
{
	int rc;

	il_wr(il, FH39_RCSR_CONFIG(0), 0);
	rc = il_poll_bit(il, FH39_RSSR_STATUS,
			FH39_RSSR_CHNL0_RX_STATUS_CHNL_IDLE, 1000);
	if (rc < 0)
		IL_ERR("Can't stop Rx DMA.\n");

	return 0;
}

int il3945_hw_tx_queue_init(struct il_priv *il, struct il_tx_queue *txq)
{
	int txq_id = txq->q.id;

	struct il3945_shared *shared_data = il->_3945.shared_virt;

	shared_data->tx_base_ptr[txq_id] = cpu_to_le32((u32)txq->q.dma_addr);

	il_wr(il, FH39_CBCC_CTRL(txq_id), 0);
	il_wr(il, FH39_CBCC_BASE(txq_id), 0);

	il_wr(il, FH39_TCSR_CONFIG(txq_id),
		FH39_TCSR_TX_CONFIG_REG_VAL_CIRQ_RTC_NOINT |
		FH39_TCSR_TX_CONFIG_REG_VAL_MSG_MODE_TXF |
		FH39_TCSR_TX_CONFIG_REG_VAL_CIRQ_HOST_IFTFD |
		FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CREDIT_ENABLE_VAL |
		FH39_TCSR_TX_CONFIG_REG_VAL_DMA_CHNL_ENABLE);

	/* fake read to flush all prev. writes */
	_il_rd(il, FH39_TSSR_CBB_BASE);

	return 0;
}

/*
 * HCMD utils
 */
static u16 il3945_get_hcmd_size(u8 cmd_id, u16 len)
{
	switch (cmd_id) {
	case REPLY_RXON:
		return sizeof(struct il3945_rxon_cmd);
	case POWER_TABLE_CMD:
		return sizeof(struct il3945_powertable_cmd);
	default:
		return len;
	}
}


static u16 il3945_build_addsta_hcmd(const struct il_addsta_cmd *cmd,
								u8 *data)
{
	struct il3945_addsta_cmd *addsta = (struct il3945_addsta_cmd *)data;
	addsta->mode = cmd->mode;
	memcpy(&addsta->sta, &cmd->sta, sizeof(struct sta_id_modify));
	memcpy(&addsta->key, &cmd->key, sizeof(struct il4965_keyinfo));
	addsta->station_flags = cmd->station_flags;
	addsta->station_flags_msk = cmd->station_flags_msk;
	addsta->tid_disable_tx = cpu_to_le16(0);
	addsta->rate_n_flags = cmd->rate_n_flags;
	addsta->add_immediate_ba_tid = cmd->add_immediate_ba_tid;
	addsta->remove_immediate_ba_tid = cmd->remove_immediate_ba_tid;
	addsta->add_immediate_ba_ssn = cmd->add_immediate_ba_ssn;

	return (u16)sizeof(struct il3945_addsta_cmd);
}

static int il3945_add_bssid_station(struct il_priv *il,
				     const u8 *addr, u8 *sta_id_r)
{
	struct il_rxon_context *ctx = &il->contexts[IL_RXON_CTX_BSS];
	int ret;
	u8 sta_id;
	unsigned long flags;

	if (sta_id_r)
		*sta_id_r = IL_INVALID_STATION;

	ret = il_add_station_common(il, ctx, addr, 0, NULL, &sta_id);
	if (ret) {
		IL_ERR("Unable to add station %pM\n", addr);
		return ret;
	}

	if (sta_id_r)
		*sta_id_r = sta_id;

	spin_lock_irqsave(&il->sta_lock, flags);
	il->stations[sta_id].used |= IL_STA_LOCAL;
	spin_unlock_irqrestore(&il->sta_lock, flags);

	return 0;
}
static int il3945_manage_ibss_station(struct il_priv *il,
				       struct ieee80211_vif *vif, bool add)
{
	struct il_vif_priv *vif_priv = (void *)vif->drv_priv;
	int ret;

	if (add) {
		ret = il3945_add_bssid_station(il, vif->bss_conf.bssid,
						&vif_priv->ibss_bssid_sta_id);
		if (ret)
			return ret;

		il3945_sync_sta(il, vif_priv->ibss_bssid_sta_id,
				 (il->band == IEEE80211_BAND_5GHZ) ?
				 IL_RATE_6M_PLCP : IL_RATE_1M_PLCP);
		il3945_rate_scale_init(il->hw, vif_priv->ibss_bssid_sta_id);

		return 0;
	}

	return il_remove_station(il, vif_priv->ibss_bssid_sta_id,
				  vif->bss_conf.bssid);
}

/**
 * il3945_init_hw_rate_table - Initialize the hardware rate fallback table
 */
int il3945_init_hw_rate_table(struct il_priv *il)
{
	int rc, i, index, prev_index;
	struct il3945_rate_scaling_cmd rate_cmd = {
		.reserved = {0, 0, 0},
	};
	struct il3945_rate_scaling_info *table = rate_cmd.table;

	for (i = 0; i < ARRAY_SIZE(il3945_rates); i++) {
		index = il3945_rates[i].table_rs_index;

		table[index].rate_n_flags =
			il3945_hw_set_rate_n_flags(il3945_rates[i].plcp, 0);
		table[index].try_cnt = il->retry_rate;
		prev_index = il3945_get_prev_ieee_rate(i);
		table[index].next_rate_index =
				il3945_rates[prev_index].table_rs_index;
	}

	switch (il->band) {
	case IEEE80211_BAND_5GHZ:
		D_RATE("Select A mode rate scale\n");
		/* If one of the following CCK rates is used,
		 * have it fall back to the 6M OFDM rate */
		for (i = IL_RATE_1M_INDEX_TABLE;
			i <= IL_RATE_11M_INDEX_TABLE; i++)
			table[i].next_rate_index =
			  il3945_rates[IL_FIRST_OFDM_RATE].table_rs_index;

		/* Don't fall back to CCK rates */
		table[IL_RATE_12M_INDEX_TABLE].next_rate_index =
						IL_RATE_9M_INDEX_TABLE;

		/* Don't drop out of OFDM rates */
		table[IL_RATE_6M_INDEX_TABLE].next_rate_index =
		    il3945_rates[IL_FIRST_OFDM_RATE].table_rs_index;
		break;

	case IEEE80211_BAND_2GHZ:
		D_RATE("Select B/G mode rate scale\n");
		/* If an OFDM rate is used, have it fall back to the
		 * 1M CCK rates */

		if (!(il->_3945.sta_supp_rates & IL_OFDM_RATES_MASK) &&
		    il_is_associated(il, IL_RXON_CTX_BSS)) {

			index = IL_FIRST_CCK_RATE;
			for (i = IL_RATE_6M_INDEX_TABLE;
			     i <= IL_RATE_54M_INDEX_TABLE; i++)
				table[i].next_rate_index =
					il3945_rates[index].table_rs_index;

			index = IL_RATE_11M_INDEX_TABLE;
			/* CCK shouldn't fall back to OFDM... */
			table[index].next_rate_index = IL_RATE_5M_INDEX_TABLE;
		}
		break;

	default:
		WARN_ON(1);
		break;
	}

	/* Update the rate scaling for control frame Tx */
	rate_cmd.table_id = 0;
	rc = il_send_cmd_pdu(il, REPLY_RATE_SCALE, sizeof(rate_cmd),
			      &rate_cmd);
	if (rc)
		return rc;

	/* Update the rate scaling for data frame Tx */
	rate_cmd.table_id = 1;
	return il_send_cmd_pdu(il, REPLY_RATE_SCALE, sizeof(rate_cmd),
				&rate_cmd);
}

/* Called when initializing driver */
int il3945_hw_set_hw_params(struct il_priv *il)
{
	memset((void *)&il->hw_params, 0,
	       sizeof(struct il_hw_params));

	il->_3945.shared_virt =
		dma_alloc_coherent(&il->pci_dev->dev,
				   sizeof(struct il3945_shared),
				   &il->_3945.shared_phys, GFP_KERNEL);
	if (!il->_3945.shared_virt) {
		IL_ERR("failed to allocate pci memory\n");
		return -ENOMEM;
	}

	/* Assign number of Usable TX queues */
	il->hw_params.max_txq_num = il->cfg->base_params->num_of_queues;

	il->hw_params.tfd_size = sizeof(struct il3945_tfd);
	il->hw_params.rx_page_order = get_order(IL_RX_BUF_SIZE_3K);
	il->hw_params.max_rxq_size = RX_QUEUE_SIZE;
	il->hw_params.max_rxq_log = RX_QUEUE_SIZE_LOG;
	il->hw_params.max_stations = IWL3945_STATION_COUNT;
	il->contexts[IL_RXON_CTX_BSS].bcast_sta_id = IWL3945_BROADCAST_ID;

	il->sta_key_max_num = STA_KEY_MAX_NUM;

	il->hw_params.rx_wrt_ptr_reg = FH39_RSCSR_CHNL0_WPTR;
	il->hw_params.max_beacon_itrvl = IWL39_MAX_UCODE_BEACON_INTERVAL;
	il->hw_params.beacon_time_tsf_bits = IWL3945_EXT_BEACON_TIME_POS;

	return 0;
}

unsigned int il3945_hw_get_beacon_cmd(struct il_priv *il,
			  struct il3945_frame *frame, u8 rate)
{
	struct il3945_tx_beacon_cmd *tx_beacon_cmd;
	unsigned int frame_size;

	tx_beacon_cmd = (struct il3945_tx_beacon_cmd *)&frame->u;
	memset(tx_beacon_cmd, 0, sizeof(*tx_beacon_cmd));

	tx_beacon_cmd->tx.sta_id =
		il->contexts[IL_RXON_CTX_BSS].bcast_sta_id;
	tx_beacon_cmd->tx.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE;

	frame_size = il3945_fill_beacon_frame(il,
				tx_beacon_cmd->frame,
				sizeof(frame->u) - sizeof(*tx_beacon_cmd));

	BUG_ON(frame_size > MAX_MPDU_SIZE);
	tx_beacon_cmd->tx.len = cpu_to_le16((u16)frame_size);

	tx_beacon_cmd->tx.rate = rate;
	tx_beacon_cmd->tx.tx_flags = (TX_CMD_FLG_SEQ_CTL_MSK |
				      TX_CMD_FLG_TSF_MSK);

	/* supp_rates[0] == OFDM start at IL_FIRST_OFDM_RATE*/
	tx_beacon_cmd->tx.supp_rates[0] =
		(IL_OFDM_BASIC_RATES_MASK >> IL_FIRST_OFDM_RATE) & 0xFF;

	tx_beacon_cmd->tx.supp_rates[1] =
		(IL_CCK_BASIC_RATES_MASK & 0xF);

	return sizeof(struct il3945_tx_beacon_cmd) + frame_size;
}

void il3945_hw_rx_handler_setup(struct il_priv *il)
{
	il->rx_handlers[REPLY_TX] = il3945_rx_reply_tx;
	il->rx_handlers[REPLY_3945_RX] = il3945_rx_reply_rx;
}

void il3945_hw_setup_deferred_work(struct il_priv *il)
{
	INIT_DELAYED_WORK(&il->_3945.thermal_periodic,
			  il3945_bg_reg_txpower_periodic);
}

void il3945_hw_cancel_deferred_work(struct il_priv *il)
{
	cancel_delayed_work(&il->_3945.thermal_periodic);
}

/* check contents of special bootstrap uCode SRAM */
static int il3945_verify_bsm(struct il_priv *il)
 {
	__le32 *image = il->ucode_boot.v_addr;
	u32 len = il->ucode_boot.len;
	u32 reg;
	u32 val;

	D_INFO("Begin verify bsm\n");

	/* verify BSM SRAM contents */
	val = il_rd_prph(il, BSM_WR_DWCOUNT_REG);
	for (reg = BSM_SRAM_LOWER_BOUND;
	     reg < BSM_SRAM_LOWER_BOUND + len;
	     reg += sizeof(u32), image++) {
		val = il_rd_prph(il, reg);
		if (val != le32_to_cpu(*image)) {
			IL_ERR("BSM uCode verification failed at "
				  "addr 0x%08X+%u (of %u), is 0x%x, s/b 0x%x\n",
				  BSM_SRAM_LOWER_BOUND,
				  reg - BSM_SRAM_LOWER_BOUND, len,
				  val, le32_to_cpu(*image));
			return -EIO;
		}
	}

	D_INFO("BSM bootstrap uCode image OK\n");

	return 0;
}


/******************************************************************************
 *
 * EEPROM related functions
 *
 ******************************************************************************/

/*
 * Clear the OWNER_MSK, to establish driver (instead of uCode running on
 * embedded controller) as EEPROM reader; each read is a series of pulses
 * to/from the EEPROM chip, not a single event, so even reads could conflict
 * if they weren't arbitrated by some ownership mechanism.  Here, the driver
 * simply claims ownership, which should be safe when this function is called
 * (i.e. before loading uCode!).
 */
static int il3945_eeprom_acquire_semaphore(struct il_priv *il)
{
	_il_clear_bit(il, CSR_EEPROM_GP, CSR_EEPROM_GP_IF_OWNER_MSK);
	return 0;
}


static void il3945_eeprom_release_semaphore(struct il_priv *il)
{
	return;
}

 /**
  * il3945_load_bsm - Load bootstrap instructions
  *
  * BSM operation:
  *
  * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program
  * in special SRAM that does not power down during RFKILL.  When powering back
  * up after power-saving sleeps (or during initial uCode load), the BSM loads
  * the bootstrap program into the on-board processor, and starts it.
  *
  * The bootstrap program loads (via DMA) instructions and data for a new
  * program from host DRAM locations indicated by the host driver in the
  * BSM_DRAM_* registers.  Once the new program is loaded, it starts
  * automatically.
  *
  * When initializing the NIC, the host driver points the BSM to the
  * "initialize" uCode image.  This uCode sets up some internal data, then
  * notifies host via "initialize alive" that it is complete.
  *
  * The host then replaces the BSM_DRAM_* pointer values to point to the
  * normal runtime uCode instructions and a backup uCode data cache buffer
  * (filled initially with starting data values for the on-board processor),
  * then triggers the "initialize" uCode to load and launch the runtime uCode,
  * which begins normal operation.
  *
  * When doing a power-save shutdown, runtime uCode saves data SRAM into
  * the backup data cache in DRAM before SRAM is powered down.
  *
  * When powering back up, the BSM loads the bootstrap program.  This reloads
  * the runtime uCode instructions and the backup data cache into SRAM,
  * and re-launches the runtime uCode from where it left off.
  */
static int il3945_load_bsm(struct il_priv *il)
{
	__le32 *image = il->ucode_boot.v_addr;
	u32 len = il->ucode_boot.len;
	dma_addr_t pinst;
	dma_addr_t pdata;
	u32 inst_len;
	u32 data_len;
	int rc;
	int i;
	u32 done;
	u32 reg_offset;

	D_INFO("Begin load bsm\n");

	/* make sure bootstrap program is no larger than BSM's SRAM size */
	if (len > IWL39_MAX_BSM_SIZE)
		return -EINVAL;

	/* Tell bootstrap uCode where to find the "Initialize" uCode
	*   in host DRAM ... host DRAM physical address bits 31:0 for 3945.
	* NOTE:  il3945_initialize_alive_start() will replace these values,
	*        after the "initialize" uCode has run, to point to
	*        runtime/protocol instructions and backup data cache. */
	pinst = il->ucode_init.p_addr;
	pdata = il->ucode_init_data.p_addr;
	inst_len = il->ucode_init.len;
	data_len = il->ucode_init_data.len;

	il_wr_prph(il, BSM_DRAM_INST_PTR_REG, pinst);
	il_wr_prph(il, BSM_DRAM_DATA_PTR_REG, pdata);
	il_wr_prph(il, BSM_DRAM_INST_BYTECOUNT_REG, inst_len);
	il_wr_prph(il, BSM_DRAM_DATA_BYTECOUNT_REG, data_len);

	/* Fill BSM memory with bootstrap instructions */
	for (reg_offset = BSM_SRAM_LOWER_BOUND;
	     reg_offset < BSM_SRAM_LOWER_BOUND + len;
	     reg_offset += sizeof(u32), image++)
		_il_wr_prph(il, reg_offset,
					  le32_to_cpu(*image));

	rc = il3945_verify_bsm(il);
	if (rc)
		return rc;

	/* Tell BSM to copy from BSM SRAM into instruction SRAM, when asked */
	il_wr_prph(il, BSM_WR_MEM_SRC_REG, 0x0);
	il_wr_prph(il, BSM_WR_MEM_DST_REG,
				 IWL39_RTC_INST_LOWER_BOUND);
	il_wr_prph(il, BSM_WR_DWCOUNT_REG, len / sizeof(u32));

	/* Load bootstrap code into instruction SRAM now,
	 *   to prepare to load "initialize" uCode */
	il_wr_prph(il, BSM_WR_CTRL_REG,
		BSM_WR_CTRL_REG_BIT_START);

	/* Wait for load of bootstrap uCode to finish */
	for (i = 0; i < 100; i++) {
		done = il_rd_prph(il, BSM_WR_CTRL_REG);
		if (!(done & BSM_WR_CTRL_REG_BIT_START))
			break;
		udelay(10);
	}
	if (i < 100)
		D_INFO("BSM write complete, poll %d iterations\n", i);
	else {
		IL_ERR("BSM write did not complete!\n");
		return -EIO;
	}

	/* Enable future boot loads whenever power management unit triggers it
	 *   (e.g. when powering back up after power-save shutdown) */
	il_wr_prph(il, BSM_WR_CTRL_REG,
		BSM_WR_CTRL_REG_BIT_START_EN);

	return 0;
}

static struct il_hcmd_ops il3945_hcmd = {
	.rxon_assoc = il3945_send_rxon_assoc,
	.commit_rxon = il3945_commit_rxon,
};

static struct il_lib_ops il3945_lib = {
	.txq_attach_buf_to_tfd = il3945_hw_txq_attach_buf_to_tfd,
	.txq_free_tfd = il3945_hw_txq_free_tfd,
	.txq_init = il3945_hw_tx_queue_init,
	.load_ucode = il3945_load_bsm,
	.dump_nic_error_log = il3945_dump_nic_error_log,
	.apm_ops = {
		.init = il3945_apm_init,
		.config = il3945_nic_config,
	},
	.eeprom_ops = {
		.regulatory_bands = {
			EEPROM_REGULATORY_BAND_1_CHANNELS,
			EEPROM_REGULATORY_BAND_2_CHANNELS,
			EEPROM_REGULATORY_BAND_3_CHANNELS,
			EEPROM_REGULATORY_BAND_4_CHANNELS,
			EEPROM_REGULATORY_BAND_5_CHANNELS,
			EEPROM_REGULATORY_BAND_NO_HT40,
			EEPROM_REGULATORY_BAND_NO_HT40,
		},
		.acquire_semaphore = il3945_eeprom_acquire_semaphore,
		.release_semaphore = il3945_eeprom_release_semaphore,
	},
	.send_tx_power	= il3945_send_tx_power,
	.is_valid_rtc_data_addr = il3945_hw_valid_rtc_data_addr,

	.debugfs_ops = {
		.rx_stats_read = il3945_ucode_rx_stats_read,
		.tx_stats_read = il3945_ucode_tx_stats_read,
		.general_stats_read = il3945_ucode_general_stats_read,
	},
};

static const struct il_legacy_ops il3945_legacy_ops = {
	.post_associate = il3945_post_associate,
	.config_ap = il3945_config_ap,
	.manage_ibss_station = il3945_manage_ibss_station,
};

static struct il_hcmd_utils_ops il3945_hcmd_utils = {
	.get_hcmd_size = il3945_get_hcmd_size,
	.build_addsta_hcmd = il3945_build_addsta_hcmd,
	.request_scan = il3945_request_scan,
	.post_scan = il3945_post_scan,
};

static const struct il_ops il3945_ops = {
	.lib = &il3945_lib,
	.hcmd = &il3945_hcmd,
	.utils = &il3945_hcmd_utils,
	.led = &il3945_led_ops,
	.legacy = &il3945_legacy_ops,
	.ieee80211_ops = &il3945_hw_ops,
};

static struct il_base_params il3945_base_params = {
	.eeprom_size = IWL3945_EEPROM_IMG_SIZE,
	.num_of_queues = IWL39_NUM_QUEUES,
	.pll_cfg_val = CSR39_ANA_PLL_CFG_VAL,
	.set_l0s = false,
	.use_bsm = true,
	.led_compensation = 64,
	.wd_timeout = IL_DEF_WD_TIMEOUT,
};

static struct il_cfg il3945_bg_cfg = {
	.name = "3945BG",
	.fw_name_pre = IWL3945_FW_PRE,
	.ucode_api_max = IWL3945_UCODE_API_MAX,
	.ucode_api_min = IWL3945_UCODE_API_MIN,
	.sku = IL_SKU_G,
	.eeprom_ver = EEPROM_3945_EEPROM_VERSION,
	.ops = &il3945_ops,
	.mod_params = &il3945_mod_params,
	.base_params = &il3945_base_params,
	.led_mode = IL_LED_BLINK,
};

static struct il_cfg il3945_abg_cfg = {
	.name = "3945ABG",
	.fw_name_pre = IWL3945_FW_PRE,
	.ucode_api_max = IWL3945_UCODE_API_MAX,
	.ucode_api_min = IWL3945_UCODE_API_MIN,
	.sku = IL_SKU_A|IL_SKU_G,
	.eeprom_ver = EEPROM_3945_EEPROM_VERSION,
	.ops = &il3945_ops,
	.mod_params = &il3945_mod_params,
	.base_params = &il3945_base_params,
	.led_mode = IL_LED_BLINK,
};

DEFINE_PCI_DEVICE_TABLE(il3945_hw_card_ids) = {
	{IL_PCI_DEVICE(0x4222, 0x1005, il3945_bg_cfg)},
	{IL_PCI_DEVICE(0x4222, 0x1034, il3945_bg_cfg)},
	{IL_PCI_DEVICE(0x4222, 0x1044, il3945_bg_cfg)},
	{IL_PCI_DEVICE(0x4227, 0x1014, il3945_bg_cfg)},
	{IL_PCI_DEVICE(0x4222, PCI_ANY_ID, il3945_abg_cfg)},
	{IL_PCI_DEVICE(0x4227, PCI_ANY_ID, il3945_abg_cfg)},
	{0}
};

MODULE_DEVICE_TABLE(pci, il3945_hw_card_ids);