blob: ab4973695c7133007cc05871d4c07634823d423b [file] [log] [blame]
Tony Lindgrenc2d43e32008-07-03 12:24:38 +03001/*
2 * linux/arch/arm/mach-omap2/sram243x.S
3 *
4 * Omap2 specific functions that need to be run in internal SRAM
5 *
6 * (C) Copyright 2004
7 * Texas Instruments, <www.ti.com>
8 * Richard Woodruff <r-woodruff2@ti.com>
9 *
10 * This program is free software; you can redistribute it and/or
11 * modify it under the terms of the GNU General Public License as
12 * published by the Free Software Foundation; either version 2 of
13 * the License, or (at your option) any later version.
14 *
15 * This program is distributed in the hope that it will be useful,
16 * but WITHOUT ANY WARRANTY; without even the implied warranty of
17 * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
18 * GNU General Public License for more details.
19 *
20 * You should have received a copy of the GNU General Public License
21 * along with this program; if not, write to the Free Software
22 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
23 * MA 02111-1307 USA
24 */
25#include <linux/linkage.h>
26#include <asm/assembler.h>
Russell Kinga09e64f2008-08-05 16:14:15 +010027#include <mach/io.h>
28#include <mach/hardware.h>
Tony Lindgrenc2d43e32008-07-03 12:24:38 +030029
30#include "prm.h"
31#include "cm.h"
32#include "sdrc.h"
33
34 .text
35
36ENTRY(omap243x_sram_ddr_init)
37 stmfd sp!, {r0 - r12, lr} @ save registers on stack
38
39 mov r12, r2 @ capture CS1 vs CS0
40 mov r8, r3 @ capture force parameter
41
42 /* frequency shift down */
43 ldr r2, omap243x_sdi_cm_clksel2_pll @ get address of dpllout reg
44 mov r3, #0x1 @ value for 1x operation
45 str r3, [r2] @ go to L1-freq operation
46
47 /* voltage shift down */
48 mov r9, #0x1 @ set up for L1 voltage call
49 bl voltage_shift @ go drop voltage
50
51 /* dll lock mode */
52 ldr r11, omap243x_sdi_sdrc_dlla_ctrl @ addr of dlla ctrl
53 ldr r10, [r11] @ get current val
54 cmp r12, #0x1 @ cs1 base (2422 es2.05/1)
55 addeq r11, r11, #0x8 @ if cs1 base, move to DLLB
56 mvn r9, #0x4 @ mask to get clear bit2
57 and r10, r10, r9 @ clear bit2 for lock mode.
58 orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
59 orr r10, r10, #0x2 @ 90 degree phase for all below 133Mhz
60 str r10, [r11] @ commit to DLLA_CTRL
61 bl i_dll_wait @ wait for dll to lock
62
63 /* get dll value */
64 add r11, r11, #0x4 @ get addr of status reg
65 ldr r10, [r11] @ get locked value
66
67 /* voltage shift up */
68 mov r9, #0x0 @ shift back to L0-voltage
69 bl voltage_shift @ go raise voltage
70
71 /* frequency shift up */
72 mov r3, #0x2 @ value for 2x operation
73 str r3, [r2] @ go to L0-freq operation
74
75 /* reset entry mode for dllctrl */
76 sub r11, r11, #0x4 @ move from status to ctrl
77 cmp r12, #0x1 @ normalize if cs1 based
78 subeq r11, r11, #0x8 @ possibly back to DLLA
79 cmp r8, #0x1 @ if forced unlock exit
80 orreq r1, r1, #0x4 @ make sure exit with unlocked value
81 str r1, [r11] @ restore DLLA_CTRL high value
82 add r11, r11, #0x8 @ move to DLLB_CTRL addr
83 str r1, [r11] @ set value DLLB_CTRL
84 bl i_dll_wait @ wait for possible lock
85
86 /* set up for return, DDR should be good */
87 str r10, [r0] @ write dll_status and return counter
88 ldmfd sp!, {r0 - r12, pc} @ restore regs and return
89
90 /* ensure the DLL has relocked */
91i_dll_wait:
92 mov r4, #0x800 @ delay DLL relock, min 0x400 L3 clocks
93i_dll_delay:
94 subs r4, r4, #0x1
95 bne i_dll_delay
96 mov pc, lr
97
98 /*
99 * shift up or down voltage, use R9 as input to tell level.
100 * wait for it to finish, use 32k sync counter, 1tick=31uS.
101 */
102voltage_shift:
103 ldr r4, omap243x_sdi_prcm_voltctrl @ get addr of volt ctrl.
104 ldr r5, [r4] @ get value.
105 ldr r6, prcm_mask_val @ get value of mask
106 and r5, r5, r6 @ apply mask to clear bits
107 orr r5, r5, r9 @ bulld value for L0/L1-volt operation.
108 str r5, [r4] @ set up for change.
109 mov r3, #0x4000 @ get val for force
110 orr r5, r5, r3 @ build value for force
111 str r5, [r4] @ Force transition to L1
112
113 ldr r3, omap243x_sdi_timer_32ksynct_cr @ get addr of counter
114 ldr r5, [r3] @ get value
115 add r5, r5, #0x3 @ give it at most 93uS
116volt_delay:
117 ldr r7, [r3] @ get timer value
118 cmp r5, r7 @ time up?
119 bhi volt_delay @ not yet->branch
120 mov pc, lr @ back to caller.
121
122omap243x_sdi_cm_clksel2_pll:
123 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
124omap243x_sdi_sdrc_dlla_ctrl:
125 .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
126omap243x_sdi_prcm_voltctrl:
Tony Lindgren8e3bd352009-05-25 11:26:42 -0700127 .word OMAP2430_PRCM_VOLTCTRL
Tony Lindgrenc2d43e32008-07-03 12:24:38 +0300128prcm_mask_val:
129 .word 0xFFFF3FFC
130omap243x_sdi_timer_32ksynct_cr:
Santosh Shilimkar233fd642009-10-19 15:25:31 -0700131 .word OMAP2_L4_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
Tony Lindgrenc2d43e32008-07-03 12:24:38 +0300132ENTRY(omap243x_sram_ddr_init_sz)
133 .word . - omap243x_sram_ddr_init
134
135/*
136 * Reprograms memory timings.
137 * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR]
138 * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0
139 */
140ENTRY(omap243x_sram_reprogram_sdrc)
141 stmfd sp!, {r0 - r10, lr} @ save registers on stack
142 mov r3, #0x0 @ clear for mrc call
143 mcr p15, 0, r3, c7, c10, 4 @ memory barrier, finish ARM SDR/DDR
144 nop
145 nop
146 ldr r6, omap243x_srs_sdrc_rfr_ctrl @ get addr of refresh reg
147 ldr r5, [r6] @ get value
148 mov r5, r5, lsr #8 @ isolate rfr field and drop burst
149
150 cmp r0, #0x1 @ going to half speed?
151 movne r9, #0x0 @ if up set flag up for pre up, hi volt
152
153 blne voltage_shift_c @ adjust voltage
154
155 cmp r0, #0x1 @ going to half speed (post branch link)
156 moveq r5, r5, lsr #1 @ divide by 2 if to half
157 movne r5, r5, lsl #1 @ mult by 2 if to full
158 mov r5, r5, lsl #8 @ put rfr field back into place
159 add r5, r5, #0x1 @ turn on burst of 1
160 ldr r4, omap243x_srs_cm_clksel2_pll @ get address of out reg
161 ldr r3, [r4] @ get curr value
162 orr r3, r3, #0x3
163 bic r3, r3, #0x3 @ clear lower bits
164 orr r3, r3, r0 @ new state value
165 str r3, [r4] @ set new state (pll/x, x=1 or 2)
166 nop
167 nop
168
169 moveq r9, #0x1 @ if speed down, post down, drop volt
170 bleq voltage_shift_c
171
172 mcr p15, 0, r3, c7, c10, 4 @ memory barrier
173 str r5, [r6] @ set new RFR_1 value
174 add r6, r6, #0x30 @ get RFR_2 addr
175 str r5, [r6] @ set RFR_2
176 nop
177 cmp r2, #0x1 @ (SDR or DDR) do we need to adjust DLL
178 bne freq_out @ leave if SDR, no DLL function
179
180 /* With DDR, we need to take care of the DLL for the frequency change */
181 ldr r2, omap243x_srs_sdrc_dlla_ctrl @ addr of dlla ctrl
182 str r1, [r2] @ write out new SDRC_DLLA_CTRL
183 add r2, r2, #0x8 @ addr to SDRC_DLLB_CTRL
184 str r1, [r2] @ commit to SDRC_DLLB_CTRL
185 mov r1, #0x2000 @ wait DLL relock, min 0x400 L3 clocks
186dll_wait:
187 subs r1, r1, #0x1
188 bne dll_wait
189freq_out:
190 ldmfd sp!, {r0 - r10, pc} @ restore regs and return
191
192 /*
193 * shift up or down voltage, use R9 as input to tell level.
194 * wait for it to finish, use 32k sync counter, 1tick=31uS.
195 */
196voltage_shift_c:
197 ldr r10, omap243x_srs_prcm_voltctrl @ get addr of volt ctrl
198 ldr r8, [r10] @ get value
199 ldr r7, ddr_prcm_mask_val @ get value of mask
200 and r8, r8, r7 @ apply mask to clear bits
201 orr r8, r8, r9 @ bulld value for L0/L1-volt operation.
202 str r8, [r10] @ set up for change.
203 mov r7, #0x4000 @ get val for force
204 orr r8, r8, r7 @ build value for force
205 str r8, [r10] @ Force transition to L1
206
207 ldr r10, omap243x_srs_timer_32ksynct @ get addr of counter
208 ldr r8, [r10] @ get value
209 add r8, r8, #0x2 @ give it at most 62uS (min 31+)
210volt_delay_c:
211 ldr r7, [r10] @ get timer value
212 cmp r8, r7 @ time up?
213 bhi volt_delay_c @ not yet->branch
214 mov pc, lr @ back to caller
215
216omap243x_srs_cm_clksel2_pll:
217 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
218omap243x_srs_sdrc_dlla_ctrl:
219 .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
220omap243x_srs_sdrc_rfr_ctrl:
221 .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
222omap243x_srs_prcm_voltctrl:
Tony Lindgren8e3bd352009-05-25 11:26:42 -0700223 .word OMAP2430_PRCM_VOLTCTRL
Tony Lindgrenc2d43e32008-07-03 12:24:38 +0300224ddr_prcm_mask_val:
225 .word 0xFFFF3FFC
226omap243x_srs_timer_32ksynct:
Santosh Shilimkar233fd642009-10-19 15:25:31 -0700227 .word OMAP2_L4_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
Tony Lindgrenc2d43e32008-07-03 12:24:38 +0300228
229ENTRY(omap243x_sram_reprogram_sdrc_sz)
230 .word . - omap243x_sram_reprogram_sdrc
231
232/*
233 * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode.
234 */
235ENTRY(omap243x_sram_set_prcm)
236 stmfd sp!, {r0-r12, lr} @ regs to stack
237 adr r4, pbegin @ addr of preload start
238 adr r8, pend @ addr of preload end
239 mcrr p15, 1, r8, r4, c12 @ preload into icache
240pbegin:
241 /* move into fast relock bypass */
242 ldr r8, omap243x_ssp_pll_ctl @ get addr
243 ldr r5, [r8] @ get val
244 mvn r6, #0x3 @ clear mask
245 and r5, r5, r6 @ clear field
246 orr r7, r5, #0x2 @ fast relock val
247 str r7, [r8] @ go to fast relock
248 ldr r4, omap243x_ssp_pll_stat @ addr of stat
249block:
250 /* wait for bypass */
251 ldr r8, [r4] @ stat value
252 and r8, r8, #0x3 @ mask for stat
253 cmp r8, #0x1 @ there yet
254 bne block @ loop if not
255
256 /* set new dpll dividers _after_ in bypass */
257 ldr r4, omap243x_ssp_pll_div @ get addr
258 str r0, [r4] @ set dpll ctrl val
259
260 ldr r4, omap243x_ssp_set_config @ get addr
261 mov r8, #1 @ valid cfg msk
262 str r8, [r4] @ make dividers take
263
264 mov r4, #100 @ dead spin a bit
265wait_a_bit:
266 subs r4, r4, #1 @ dec loop
267 bne wait_a_bit @ delay done?
268
269 /* check if staying in bypass */
270 cmp r2, #0x1 @ stay in bypass?
271 beq pend @ jump over dpll relock
272
273 /* relock DPLL with new vals */
274 ldr r5, omap243x_ssp_pll_stat @ get addr
275 ldr r4, omap243x_ssp_pll_ctl @ get addr
276 orr r8, r7, #0x3 @ val for lock dpll
277 str r8, [r4] @ set val
278 mov r0, #1000 @ dead spin a bit
279wait_more:
280 subs r0, r0, #1 @ dec loop
281 bne wait_more @ delay done?
282wait_lock:
283 ldr r8, [r5] @ get lock val
284 and r8, r8, #3 @ isolate field
285 cmp r8, #2 @ locked?
286 bne wait_lock @ wait if not
287pend:
288 /* update memory timings & briefly lock dll */
289 ldr r4, omap243x_ssp_sdrc_rfr @ get addr
290 str r1, [r4] @ update refresh timing
291 ldr r11, omap243x_ssp_dlla_ctrl @ get addr of DLLA ctrl
292 ldr r10, [r11] @ get current val
293 mvn r9, #0x4 @ mask to get clear bit2
294 and r10, r10, r9 @ clear bit2 for lock mode
295 orr r10, r10, #0x8 @ make sure DLL on (es2 bit pos)
296 str r10, [r11] @ commit to DLLA_CTRL
297 add r11, r11, #0x8 @ move to dllb
298 str r10, [r11] @ hit DLLB also
299
300 mov r4, #0x800 @ relock time (min 0x400 L3 clocks)
301wait_dll_lock:
302 subs r4, r4, #0x1
303 bne wait_dll_lock
304 nop
305 ldmfd sp!, {r0-r12, pc} @ restore regs and return
306
307omap243x_ssp_set_config:
Tony Lindgren8e3bd352009-05-25 11:26:42 -0700308 .word OMAP2430_PRCM_CLKCFG_CTRL
Tony Lindgrenc2d43e32008-07-03 12:24:38 +0300309omap243x_ssp_pll_ctl:
310 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKEN)
311omap243x_ssp_pll_stat:
312 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_IDLEST)
313omap243x_ssp_pll_div:
314 .word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL1)
315omap243x_ssp_sdrc_rfr:
316 .word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
317omap243x_ssp_dlla_ctrl:
318 .word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
319
320ENTRY(omap243x_sram_set_prcm_sz)
321 .word . - omap243x_sram_set_prcm