blob: ebff4a1d4bcc04626f519ebd824f94af5f25a506 [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * Driver for Zilog serial chips found on SGI workstations and
3 * servers. This driver could actually be made more generic.
4 *
5 * This is based on the drivers/serial/sunzilog.c code as of 2.6.0-test7 and the
6 * old drivers/sgi/char/sgiserial.c code which itself is based of the original
7 * drivers/sbus/char/zs.c code. A lot of code has been simply moved over
8 * directly from there but much has been rewritten. Credits therefore go out
9 * to David S. Miller, Eddie C. Dost, Pete Zaitcev, Ted Ts'o and Alex Buell
10 * for their work there.
11 *
12 * Copyright (C) 2002 Ralf Baechle (ralf@linux-mips.org)
13 * Copyright (C) 2002 David S. Miller (davem@redhat.com)
14 */
Linus Torvalds1da177e2005-04-16 15:20:36 -070015#include <linux/module.h>
16#include <linux/kernel.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -070017#include <linux/errno.h>
18#include <linux/delay.h>
19#include <linux/tty.h>
20#include <linux/tty_flip.h>
21#include <linux/major.h>
22#include <linux/string.h>
23#include <linux/ptrace.h>
24#include <linux/ioport.h>
25#include <linux/slab.h>
26#include <linux/circ_buf.h>
27#include <linux/serial.h>
28#include <linux/sysrq.h>
29#include <linux/console.h>
30#include <linux/spinlock.h>
31#include <linux/init.h>
32
33#include <asm/io.h>
34#include <asm/irq.h>
35#include <asm/sgialib.h>
36#include <asm/sgi/ioc.h>
37#include <asm/sgi/hpc3.h>
38#include <asm/sgi/ip22.h>
39
40#if defined(CONFIG_SERIAL_IP22_ZILOG_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
41#define SUPPORT_SYSRQ
42#endif
43
44#include <linux/serial_core.h>
45
46#include "ip22zilog.h"
47
Linus Torvalds1da177e2005-04-16 15:20:36 -070048/*
49 * On IP22 we need to delay after register accesses but we do not need to
50 * flush writes.
51 */
52#define ZSDELAY() udelay(5)
53#define ZSDELAY_LONG() udelay(20)
54#define ZS_WSYNC(channel) do { } while (0)
55
56#define NUM_IP22ZILOG 1
57#define NUM_CHANNELS (NUM_IP22ZILOG * 2)
58
59#define ZS_CLOCK 3672000 /* Zilog input clock rate. */
60#define ZS_CLOCK_DIVISOR 16 /* Divisor this driver uses. */
61
62/*
63 * We wrap our port structure around the generic uart_port.
64 */
65struct uart_ip22zilog_port {
66 struct uart_port port;
67
68 /* IRQ servicing chain. */
69 struct uart_ip22zilog_port *next;
70
71 /* Current values of Zilog write registers. */
72 unsigned char curregs[NUM_ZSREGS];
73
74 unsigned int flags;
75#define IP22ZILOG_FLAG_IS_CONS 0x00000004
76#define IP22ZILOG_FLAG_IS_KGDB 0x00000008
77#define IP22ZILOG_FLAG_MODEM_STATUS 0x00000010
78#define IP22ZILOG_FLAG_IS_CHANNEL_A 0x00000020
79#define IP22ZILOG_FLAG_REGS_HELD 0x00000040
80#define IP22ZILOG_FLAG_TX_STOPPED 0x00000080
81#define IP22ZILOG_FLAG_TX_ACTIVE 0x00000100
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -080082#define IP22ZILOG_FLAG_RESET_DONE 0x00000200
Linus Torvalds1da177e2005-04-16 15:20:36 -070083
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -080084 unsigned int tty_break;
Linus Torvalds1da177e2005-04-16 15:20:36 -070085
86 unsigned char parity_mask;
87 unsigned char prev_status;
88};
89
90#define ZILOG_CHANNEL_FROM_PORT(PORT) ((struct zilog_channel *)((PORT)->membase))
91#define UART_ZILOG(PORT) ((struct uart_ip22zilog_port *)(PORT))
92#define IP22ZILOG_GET_CURR_REG(PORT, REGNUM) \
93 (UART_ZILOG(PORT)->curregs[REGNUM])
94#define IP22ZILOG_SET_CURR_REG(PORT, REGNUM, REGVAL) \
95 ((UART_ZILOG(PORT)->curregs[REGNUM]) = (REGVAL))
96#define ZS_IS_CONS(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CONS)
97#define ZS_IS_KGDB(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_KGDB)
98#define ZS_WANTS_MODEM_STATUS(UP) ((UP)->flags & IP22ZILOG_FLAG_MODEM_STATUS)
99#define ZS_IS_CHANNEL_A(UP) ((UP)->flags & IP22ZILOG_FLAG_IS_CHANNEL_A)
100#define ZS_REGS_HELD(UP) ((UP)->flags & IP22ZILOG_FLAG_REGS_HELD)
101#define ZS_TX_STOPPED(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_STOPPED)
102#define ZS_TX_ACTIVE(UP) ((UP)->flags & IP22ZILOG_FLAG_TX_ACTIVE)
103
104/* Reading and writing Zilog8530 registers. The delays are to make this
105 * driver work on the IP22 which needs a settling delay after each chip
106 * register access, other machines handle this in hardware via auxiliary
107 * flip-flops which implement the settle time we do in software.
108 *
109 * The port lock must be held and local IRQs must be disabled
110 * when {read,write}_zsreg is invoked.
111 */
112static unsigned char read_zsreg(struct zilog_channel *channel,
113 unsigned char reg)
114{
115 unsigned char retval;
116
117 writeb(reg, &channel->control);
118 ZSDELAY();
119 retval = readb(&channel->control);
120 ZSDELAY();
121
122 return retval;
123}
124
125static void write_zsreg(struct zilog_channel *channel,
126 unsigned char reg, unsigned char value)
127{
128 writeb(reg, &channel->control);
129 ZSDELAY();
130 writeb(value, &channel->control);
131 ZSDELAY();
132}
133
134static void ip22zilog_clear_fifo(struct zilog_channel *channel)
135{
136 int i;
137
138 for (i = 0; i < 32; i++) {
139 unsigned char regval;
140
141 regval = readb(&channel->control);
142 ZSDELAY();
143 if (regval & Rx_CH_AV)
144 break;
145
146 regval = read_zsreg(channel, R1);
147 readb(&channel->data);
148 ZSDELAY();
149
150 if (regval & (PAR_ERR | Rx_OVR | CRC_ERR)) {
151 writeb(ERR_RES, &channel->control);
152 ZSDELAY();
153 ZS_WSYNC(channel);
154 }
155 }
156}
157
158/* This function must only be called when the TX is not busy. The UART
159 * port lock must be held and local interrupts disabled.
160 */
161static void __load_zsregs(struct zilog_channel *channel, unsigned char *regs)
162{
163 int i;
164
165 /* Let pending transmits finish. */
166 for (i = 0; i < 1000; i++) {
167 unsigned char stat = read_zsreg(channel, R1);
168 if (stat & ALL_SNT)
169 break;
170 udelay(100);
171 }
172
173 writeb(ERR_RES, &channel->control);
174 ZSDELAY();
175 ZS_WSYNC(channel);
176
177 ip22zilog_clear_fifo(channel);
178
179 /* Disable all interrupts. */
180 write_zsreg(channel, R1,
181 regs[R1] & ~(RxINT_MASK | TxINT_ENAB | EXT_INT_ENAB));
182
183 /* Set parity, sync config, stop bits, and clock divisor. */
184 write_zsreg(channel, R4, regs[R4]);
185
186 /* Set misc. TX/RX control bits. */
187 write_zsreg(channel, R10, regs[R10]);
188
189 /* Set TX/RX controls sans the enable bits. */
190 write_zsreg(channel, R3, regs[R3] & ~RxENAB);
191 write_zsreg(channel, R5, regs[R5] & ~TxENAB);
192
193 /* Synchronous mode config. */
194 write_zsreg(channel, R6, regs[R6]);
195 write_zsreg(channel, R7, regs[R7]);
196
197 /* Don't mess with the interrupt vector (R2, unused by us) and
198 * master interrupt control (R9). We make sure this is setup
199 * properly at probe time then never touch it again.
200 */
201
202 /* Disable baud generator. */
203 write_zsreg(channel, R14, regs[R14] & ~BRENAB);
204
205 /* Clock mode control. */
206 write_zsreg(channel, R11, regs[R11]);
207
208 /* Lower and upper byte of baud rate generator divisor. */
209 write_zsreg(channel, R12, regs[R12]);
210 write_zsreg(channel, R13, regs[R13]);
Ralf Baechle7369a8b2006-02-08 21:43:03 +0000211
Linus Torvalds1da177e2005-04-16 15:20:36 -0700212 /* Now rewrite R14, with BRENAB (if set). */
213 write_zsreg(channel, R14, regs[R14]);
214
215 /* External status interrupt control. */
216 write_zsreg(channel, R15, regs[R15]);
217
218 /* Reset external status interrupts. */
219 write_zsreg(channel, R0, RES_EXT_INT);
220 write_zsreg(channel, R0, RES_EXT_INT);
221
222 /* Rewrite R3/R5, this time without enables masked. */
223 write_zsreg(channel, R3, regs[R3]);
224 write_zsreg(channel, R5, regs[R5]);
225
226 /* Rewrite R1, this time without IRQ enabled masked. */
227 write_zsreg(channel, R1, regs[R1]);
228}
229
230/* Reprogram the Zilog channel HW registers with the copies found in the
231 * software state struct. If the transmitter is busy, we defer this update
232 * until the next TX complete interrupt. Else, we do it right now.
233 *
234 * The UART port lock must be held and local interrupts disabled.
235 */
236static void ip22zilog_maybe_update_regs(struct uart_ip22zilog_port *up,
237 struct zilog_channel *channel)
238{
239 if (!ZS_REGS_HELD(up)) {
240 if (ZS_TX_ACTIVE(up)) {
241 up->flags |= IP22ZILOG_FLAG_REGS_HELD;
242 } else {
243 __load_zsregs(channel, up->curregs);
244 }
245 }
246}
247
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800248#define Rx_BRK 0x0100 /* BREAK event software flag. */
249#define Rx_SYS 0x0200 /* SysRq event software flag. */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700250
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800251static struct tty_struct *ip22zilog_receive_chars(struct uart_ip22zilog_port *up,
252 struct zilog_channel *channel)
253{
254 struct tty_struct *tty;
255 unsigned char ch, flag;
256 unsigned int r1;
257
258 tty = NULL;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700259 if (up->port.state != NULL &&
260 up->port.state->port.tty != NULL)
261 tty = up->port.state->port.tty;
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800262
263 for (;;) {
264 ch = readb(&channel->control);
265 ZSDELAY();
266 if (!(ch & Rx_CH_AV))
267 break;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700268
269 r1 = read_zsreg(channel, R1);
270 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR)) {
271 writeb(ERR_RES, &channel->control);
272 ZSDELAY();
273 ZS_WSYNC(channel);
274 }
275
Linus Torvalds1da177e2005-04-16 15:20:36 -0700276 ch = readb(&channel->data);
277 ZSDELAY();
278
279 ch &= up->parity_mask;
280
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800281 /* Handle the null char got when BREAK is removed. */
282 if (!ch)
283 r1 |= up->tty_break;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700284
285 /* A real serial line, record the character and status. */
Alan Cox33f0f882006-01-09 20:54:13 -0800286 flag = TTY_NORMAL;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700287 up->port.icount.rx++;
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800288 if (r1 & (PAR_ERR | Rx_OVR | CRC_ERR | Rx_SYS | Rx_BRK)) {
289 up->tty_break = 0;
290
291 if (r1 & (Rx_SYS | Rx_BRK)) {
Linus Torvalds1da177e2005-04-16 15:20:36 -0700292 up->port.icount.brk++;
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800293 if (r1 & Rx_SYS)
294 continue;
295 r1 &= ~(PAR_ERR | CRC_ERR);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700296 }
297 else if (r1 & PAR_ERR)
298 up->port.icount.parity++;
299 else if (r1 & CRC_ERR)
300 up->port.icount.frame++;
301 if (r1 & Rx_OVR)
302 up->port.icount.overrun++;
303 r1 &= up->port.read_status_mask;
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800304 if (r1 & Rx_BRK)
Alan Cox33f0f882006-01-09 20:54:13 -0800305 flag = TTY_BREAK;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700306 else if (r1 & PAR_ERR)
Alan Cox33f0f882006-01-09 20:54:13 -0800307 flag = TTY_PARITY;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700308 else if (r1 & CRC_ERR)
Alan Cox33f0f882006-01-09 20:54:13 -0800309 flag = TTY_FRAME;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700310 }
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800311
David Howells7d12e782006-10-05 14:55:46 +0100312 if (uart_handle_sysrq_char(&up->port, ch))
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800313 continue;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700314
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800315 if (tty)
316 uart_insert_char(&up->port, r1, Rx_OVR, ch, flag);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700317 }
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800318 return tty;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700319}
320
321static void ip22zilog_status_handle(struct uart_ip22zilog_port *up,
David Howells7d12e782006-10-05 14:55:46 +0100322 struct zilog_channel *channel)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700323{
324 unsigned char status;
325
326 status = readb(&channel->control);
327 ZSDELAY();
328
329 writeb(RES_EXT_INT, &channel->control);
330 ZSDELAY();
331 ZS_WSYNC(channel);
332
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800333 if (up->curregs[R15] & BRKIE) {
334 if ((status & BRK_ABRT) && !(up->prev_status & BRK_ABRT)) {
335 if (uart_handle_break(&up->port))
336 up->tty_break = Rx_SYS;
337 else
338 up->tty_break = Rx_BRK;
339 }
340 }
341
Linus Torvalds1da177e2005-04-16 15:20:36 -0700342 if (ZS_WANTS_MODEM_STATUS(up)) {
343 if (status & SYNC)
344 up->port.icount.dsr++;
345
346 /* The Zilog just gives us an interrupt when DCD/CTS/etc. change.
347 * But it does not tell us which bit has changed, we have to keep
348 * track of this ourselves.
349 */
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800350 if ((status ^ up->prev_status) ^ DCD)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700351 uart_handle_dcd_change(&up->port,
352 (status & DCD));
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800353 if ((status ^ up->prev_status) ^ CTS)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700354 uart_handle_cts_change(&up->port,
355 (status & CTS));
356
Alan Coxbdc04e32009-09-19 13:13:31 -0700357 wake_up_interruptible(&up->port.state->port.delta_msr_wait);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700358 }
359
360 up->prev_status = status;
361}
362
363static void ip22zilog_transmit_chars(struct uart_ip22zilog_port *up,
364 struct zilog_channel *channel)
365{
366 struct circ_buf *xmit;
367
368 if (ZS_IS_CONS(up)) {
369 unsigned char status = readb(&channel->control);
370 ZSDELAY();
371
372 /* TX still busy? Just wait for the next TX done interrupt.
373 *
374 * It can occur because of how we do serial console writes. It would
375 * be nice to transmit console writes just like we normally would for
376 * a TTY line. (ie. buffered and TX interrupt driven). That is not
377 * easy because console writes cannot sleep. One solution might be
378 * to poll on enough port->xmit space becomming free. -DaveM
379 */
380 if (!(status & Tx_BUF_EMP))
381 return;
382 }
383
384 up->flags &= ~IP22ZILOG_FLAG_TX_ACTIVE;
385
386 if (ZS_REGS_HELD(up)) {
387 __load_zsregs(channel, up->curregs);
388 up->flags &= ~IP22ZILOG_FLAG_REGS_HELD;
389 }
390
391 if (ZS_TX_STOPPED(up)) {
392 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
393 goto ack_tx_int;
394 }
395
396 if (up->port.x_char) {
397 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
398 writeb(up->port.x_char, &channel->data);
399 ZSDELAY();
400 ZS_WSYNC(channel);
401
402 up->port.icount.tx++;
403 up->port.x_char = 0;
404 return;
405 }
406
Alan Coxebd2c8f2009-09-19 13:13:28 -0700407 if (up->port.state == NULL)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700408 goto ack_tx_int;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700409 xmit = &up->port.state->xmit;
Martin Michlmayrc4432c42006-03-07 21:04:59 +0000410 if (uart_circ_empty(xmit))
Linus Torvalds1da177e2005-04-16 15:20:36 -0700411 goto ack_tx_int;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700412 if (uart_tx_stopped(&up->port))
413 goto ack_tx_int;
414
415 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
416 writeb(xmit->buf[xmit->tail], &channel->data);
417 ZSDELAY();
418 ZS_WSYNC(channel);
419
420 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
421 up->port.icount.tx++;
422
423 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
424 uart_write_wakeup(&up->port);
425
426 return;
427
428ack_tx_int:
429 writeb(RES_Tx_P, &channel->control);
430 ZSDELAY();
431 ZS_WSYNC(channel);
432}
433
David Howells7d12e782006-10-05 14:55:46 +0100434static irqreturn_t ip22zilog_interrupt(int irq, void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700435{
436 struct uart_ip22zilog_port *up = dev_id;
437
438 while (up) {
439 struct zilog_channel *channel
440 = ZILOG_CHANNEL_FROM_PORT(&up->port);
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800441 struct tty_struct *tty;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700442 unsigned char r3;
443
444 spin_lock(&up->port.lock);
445 r3 = read_zsreg(channel, R3);
446
447 /* Channel A */
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800448 tty = NULL;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700449 if (r3 & (CHAEXT | CHATxIP | CHARxIP)) {
450 writeb(RES_H_IUS, &channel->control);
451 ZSDELAY();
452 ZS_WSYNC(channel);
453
454 if (r3 & CHARxIP)
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800455 tty = ip22zilog_receive_chars(up, channel);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700456 if (r3 & CHAEXT)
David Howells7d12e782006-10-05 14:55:46 +0100457 ip22zilog_status_handle(up, channel);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700458 if (r3 & CHATxIP)
459 ip22zilog_transmit_chars(up, channel);
460 }
461 spin_unlock(&up->port.lock);
462
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800463 if (tty)
464 tty_flip_buffer_push(tty);
465
Linus Torvalds1da177e2005-04-16 15:20:36 -0700466 /* Channel B */
467 up = up->next;
468 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
469
470 spin_lock(&up->port.lock);
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800471 tty = NULL;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700472 if (r3 & (CHBEXT | CHBTxIP | CHBRxIP)) {
473 writeb(RES_H_IUS, &channel->control);
474 ZSDELAY();
475 ZS_WSYNC(channel);
476
477 if (r3 & CHBRxIP)
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800478 tty = ip22zilog_receive_chars(up, channel);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700479 if (r3 & CHBEXT)
David Howells7d12e782006-10-05 14:55:46 +0100480 ip22zilog_status_handle(up, channel);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700481 if (r3 & CHBTxIP)
482 ip22zilog_transmit_chars(up, channel);
483 }
484 spin_unlock(&up->port.lock);
485
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800486 if (tty)
487 tty_flip_buffer_push(tty);
488
Linus Torvalds1da177e2005-04-16 15:20:36 -0700489 up = up->next;
490 }
491
492 return IRQ_HANDLED;
493}
494
495/* A convenient way to quickly get R0 status. The caller must _not_ hold the
496 * port lock, it is acquired here.
497 */
498static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port)
499{
500 struct zilog_channel *channel;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700501 unsigned char status;
502
Linus Torvalds1da177e2005-04-16 15:20:36 -0700503 channel = ZILOG_CHANNEL_FROM_PORT(port);
504 status = readb(&channel->control);
505 ZSDELAY();
506
Linus Torvalds1da177e2005-04-16 15:20:36 -0700507 return status;
508}
509
510/* The port lock is not held. */
511static unsigned int ip22zilog_tx_empty(struct uart_port *port)
512{
Russell Kingc5f46442005-06-29 09:42:38 +0100513 unsigned long flags;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700514 unsigned char status;
515 unsigned int ret;
516
Russell Kingc5f46442005-06-29 09:42:38 +0100517 spin_lock_irqsave(&port->lock, flags);
518
Linus Torvalds1da177e2005-04-16 15:20:36 -0700519 status = ip22zilog_read_channel_status(port);
Russell Kingc5f46442005-06-29 09:42:38 +0100520
521 spin_unlock_irqrestore(&port->lock, flags);
522
Linus Torvalds1da177e2005-04-16 15:20:36 -0700523 if (status & Tx_BUF_EMP)
524 ret = TIOCSER_TEMT;
525 else
526 ret = 0;
527
528 return ret;
529}
530
Russell Kingc5f46442005-06-29 09:42:38 +0100531/* The port lock is held and interrupts are disabled. */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700532static unsigned int ip22zilog_get_mctrl(struct uart_port *port)
533{
534 unsigned char status;
535 unsigned int ret;
536
537 status = ip22zilog_read_channel_status(port);
538
539 ret = 0;
540 if (status & DCD)
541 ret |= TIOCM_CAR;
542 if (status & SYNC)
543 ret |= TIOCM_DSR;
544 if (status & CTS)
545 ret |= TIOCM_CTS;
546
547 return ret;
548}
549
550/* The port lock is held and interrupts are disabled. */
551static void ip22zilog_set_mctrl(struct uart_port *port, unsigned int mctrl)
552{
553 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
554 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
555 unsigned char set_bits, clear_bits;
556
557 set_bits = clear_bits = 0;
558
559 if (mctrl & TIOCM_RTS)
560 set_bits |= RTS;
561 else
562 clear_bits |= RTS;
563 if (mctrl & TIOCM_DTR)
564 set_bits |= DTR;
565 else
566 clear_bits |= DTR;
567
Ralf Baechle7369a8b2006-02-08 21:43:03 +0000568 /* NOTE: Not subject to 'transmitter active' rule. */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700569 up->curregs[R5] |= set_bits;
570 up->curregs[R5] &= ~clear_bits;
571 write_zsreg(channel, R5, up->curregs[R5]);
572}
573
574/* The port lock is held and interrupts are disabled. */
Russell Kingb129a8c2005-08-31 10:12:14 +0100575static void ip22zilog_stop_tx(struct uart_port *port)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700576{
577 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
578
579 up->flags |= IP22ZILOG_FLAG_TX_STOPPED;
580}
581
582/* The port lock is held and interrupts are disabled. */
Russell Kingb129a8c2005-08-31 10:12:14 +0100583static void ip22zilog_start_tx(struct uart_port *port)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700584{
585 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
586 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
587 unsigned char status;
588
589 up->flags |= IP22ZILOG_FLAG_TX_ACTIVE;
590 up->flags &= ~IP22ZILOG_FLAG_TX_STOPPED;
591
592 status = readb(&channel->control);
593 ZSDELAY();
594
595 /* TX busy? Just wait for the TX done interrupt. */
596 if (!(status & Tx_BUF_EMP))
597 return;
598
599 /* Send the first character to jump-start the TX done
600 * IRQ sending engine.
601 */
602 if (port->x_char) {
603 writeb(port->x_char, &channel->data);
604 ZSDELAY();
605 ZS_WSYNC(channel);
606
607 port->icount.tx++;
608 port->x_char = 0;
609 } else {
Alan Coxebd2c8f2009-09-19 13:13:28 -0700610 struct circ_buf *xmit = &port->state->xmit;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700611
612 writeb(xmit->buf[xmit->tail], &channel->data);
613 ZSDELAY();
614 ZS_WSYNC(channel);
615
616 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
617 port->icount.tx++;
618
619 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
620 uart_write_wakeup(&up->port);
621 }
622}
623
624/* The port lock is held and interrupts are disabled. */
625static void ip22zilog_stop_rx(struct uart_port *port)
626{
627 struct uart_ip22zilog_port *up = UART_ZILOG(port);
628 struct zilog_channel *channel;
629
630 if (ZS_IS_CONS(up))
631 return;
632
633 channel = ZILOG_CHANNEL_FROM_PORT(port);
634
635 /* Disable all RX interrupts. */
636 up->curregs[R1] &= ~RxINT_MASK;
637 ip22zilog_maybe_update_regs(up, channel);
638}
639
640/* The port lock is held. */
641static void ip22zilog_enable_ms(struct uart_port *port)
642{
643 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
644 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
645 unsigned char new_reg;
646
647 new_reg = up->curregs[R15] | (DCDIE | SYNCIE | CTSIE);
648 if (new_reg != up->curregs[R15]) {
649 up->curregs[R15] = new_reg;
650
Ralf Baechle7369a8b2006-02-08 21:43:03 +0000651 /* NOTE: Not subject to 'transmitter active' rule. */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700652 write_zsreg(channel, R15, up->curregs[R15]);
653 }
654}
655
656/* The port lock is not held. */
657static void ip22zilog_break_ctl(struct uart_port *port, int break_state)
658{
659 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
660 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
661 unsigned char set_bits, clear_bits, new_reg;
662 unsigned long flags;
663
664 set_bits = clear_bits = 0;
665
666 if (break_state)
667 set_bits |= SND_BRK;
668 else
669 clear_bits |= SND_BRK;
670
671 spin_lock_irqsave(&port->lock, flags);
672
673 new_reg = (up->curregs[R5] | set_bits) & ~clear_bits;
674 if (new_reg != up->curregs[R5]) {
675 up->curregs[R5] = new_reg;
676
Ralf Baechle7369a8b2006-02-08 21:43:03 +0000677 /* NOTE: Not subject to 'transmitter active' rule. */
Linus Torvalds1da177e2005-04-16 15:20:36 -0700678 write_zsreg(channel, R5, up->curregs[R5]);
679 }
680
681 spin_unlock_irqrestore(&port->lock, flags);
682}
683
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800684static void __ip22zilog_reset(struct uart_ip22zilog_port *up)
685{
686 struct zilog_channel *channel;
687 int i;
688
689 if (up->flags & IP22ZILOG_FLAG_RESET_DONE)
690 return;
691
692 /* Let pending transmits finish. */
693 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
694 for (i = 0; i < 1000; i++) {
695 unsigned char stat = read_zsreg(channel, R1);
696 if (stat & ALL_SNT)
697 break;
698 udelay(100);
699 }
700
701 if (!ZS_IS_CHANNEL_A(up)) {
702 up++;
703 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
704 }
705 write_zsreg(channel, R9, FHWRES);
706 ZSDELAY_LONG();
707 (void) read_zsreg(channel, R0);
708
709 up->flags |= IP22ZILOG_FLAG_RESET_DONE;
710 up->next->flags |= IP22ZILOG_FLAG_RESET_DONE;
711}
712
Linus Torvalds1da177e2005-04-16 15:20:36 -0700713static void __ip22zilog_startup(struct uart_ip22zilog_port *up)
714{
715 struct zilog_channel *channel;
716
717 channel = ZILOG_CHANNEL_FROM_PORT(&up->port);
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -0800718
719 __ip22zilog_reset(up);
720
721 __load_zsregs(channel, up->curregs);
722 /* set master interrupt enable */
723 write_zsreg(channel, R9, up->curregs[R9]);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700724 up->prev_status = readb(&channel->control);
725
726 /* Enable receiver and transmitter. */
727 up->curregs[R3] |= RxENAB;
728 up->curregs[R5] |= TxENAB;
729
730 up->curregs[R1] |= EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
731 ip22zilog_maybe_update_regs(up, channel);
732}
733
734static int ip22zilog_startup(struct uart_port *port)
735{
736 struct uart_ip22zilog_port *up = UART_ZILOG(port);
737 unsigned long flags;
738
739 if (ZS_IS_CONS(up))
740 return 0;
741
742 spin_lock_irqsave(&port->lock, flags);
743 __ip22zilog_startup(up);
744 spin_unlock_irqrestore(&port->lock, flags);
745 return 0;
746}
747
748/*
749 * The test for ZS_IS_CONS is explained by the following e-mail:
750 *****
751 * From: Russell King <rmk@arm.linux.org.uk>
752 * Date: Sun, 8 Dec 2002 10:18:38 +0000
753 *
754 * On Sun, Dec 08, 2002 at 02:43:36AM -0500, Pete Zaitcev wrote:
755 * > I boot my 2.5 boxes using "console=ttyS0,9600" argument,
756 * > and I noticed that something is not right with reference
757 * > counting in this case. It seems that when the console
758 * > is open by kernel initially, this is not accounted
759 * > as an open, and uart_startup is not called.
760 *
761 * That is correct. We are unable to call uart_startup when the serial
762 * console is initialised because it may need to allocate memory (as
763 * request_irq does) and the memory allocators may not have been
764 * initialised.
765 *
766 * 1. initialise the port into a state where it can send characters in the
767 * console write method.
768 *
769 * 2. don't do the actual hardware shutdown in your shutdown() method (but
770 * do the normal software shutdown - ie, free irqs etc)
771 *****
772 */
773static void ip22zilog_shutdown(struct uart_port *port)
774{
775 struct uart_ip22zilog_port *up = UART_ZILOG(port);
776 struct zilog_channel *channel;
777 unsigned long flags;
778
779 if (ZS_IS_CONS(up))
780 return;
781
782 spin_lock_irqsave(&port->lock, flags);
783
784 channel = ZILOG_CHANNEL_FROM_PORT(port);
785
786 /* Disable receiver and transmitter. */
787 up->curregs[R3] &= ~RxENAB;
788 up->curregs[R5] &= ~TxENAB;
789
790 /* Disable all interrupts and BRK assertion. */
791 up->curregs[R1] &= ~(EXT_INT_ENAB | TxINT_ENAB | RxINT_MASK);
792 up->curregs[R5] &= ~SND_BRK;
793 ip22zilog_maybe_update_regs(up, channel);
794
795 spin_unlock_irqrestore(&port->lock, flags);
796}
797
798/* Shared by TTY driver and serial console setup. The port lock is held
799 * and local interrupts are disabled.
800 */
801static void
802ip22zilog_convert_to_zs(struct uart_ip22zilog_port *up, unsigned int cflag,
803 unsigned int iflag, int brg)
804{
805
806 up->curregs[R10] = NRZ;
807 up->curregs[R11] = TCBR | RCBR;
808
809 /* Program BAUD and clock source. */
810 up->curregs[R4] &= ~XCLK_MASK;
811 up->curregs[R4] |= X16CLK;
812 up->curregs[R12] = brg & 0xff;
813 up->curregs[R13] = (brg >> 8) & 0xff;
814 up->curregs[R14] = BRENAB;
815
816 /* Character size, stop bits, and parity. */
817 up->curregs[3] &= ~RxN_MASK;
818 up->curregs[5] &= ~TxN_MASK;
819 switch (cflag & CSIZE) {
820 case CS5:
821 up->curregs[3] |= Rx5;
822 up->curregs[5] |= Tx5;
823 up->parity_mask = 0x1f;
824 break;
825 case CS6:
826 up->curregs[3] |= Rx6;
827 up->curregs[5] |= Tx6;
828 up->parity_mask = 0x3f;
829 break;
830 case CS7:
831 up->curregs[3] |= Rx7;
832 up->curregs[5] |= Tx7;
833 up->parity_mask = 0x7f;
834 break;
835 case CS8:
836 default:
837 up->curregs[3] |= Rx8;
838 up->curregs[5] |= Tx8;
839 up->parity_mask = 0xff;
840 break;
841 };
842 up->curregs[4] &= ~0x0c;
843 if (cflag & CSTOPB)
844 up->curregs[4] |= SB2;
845 else
846 up->curregs[4] |= SB1;
847 if (cflag & PARENB)
848 up->curregs[4] |= PAR_ENAB;
849 else
850 up->curregs[4] &= ~PAR_ENAB;
851 if (!(cflag & PARODD))
852 up->curregs[4] |= PAR_EVEN;
853 else
854 up->curregs[4] &= ~PAR_EVEN;
855
856 up->port.read_status_mask = Rx_OVR;
857 if (iflag & INPCK)
858 up->port.read_status_mask |= CRC_ERR | PAR_ERR;
859 if (iflag & (BRKINT | PARMRK))
860 up->port.read_status_mask |= BRK_ABRT;
861
862 up->port.ignore_status_mask = 0;
863 if (iflag & IGNPAR)
864 up->port.ignore_status_mask |= CRC_ERR | PAR_ERR;
865 if (iflag & IGNBRK) {
866 up->port.ignore_status_mask |= BRK_ABRT;
867 if (iflag & IGNPAR)
868 up->port.ignore_status_mask |= Rx_OVR;
869 }
870
871 if ((cflag & CREAD) == 0)
872 up->port.ignore_status_mask = 0xff;
873}
874
875/* The port lock is not held. */
876static void
Alan Cox606d0992006-12-08 02:38:45 -0800877ip22zilog_set_termios(struct uart_port *port, struct ktermios *termios,
878 struct ktermios *old)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700879{
880 struct uart_ip22zilog_port *up = (struct uart_ip22zilog_port *) port;
881 unsigned long flags;
882 int baud, brg;
883
884 baud = uart_get_baud_rate(port, termios, old, 1200, 76800);
885
886 spin_lock_irqsave(&up->port.lock, flags);
887
888 brg = BPS_TO_BRG(baud, ZS_CLOCK / ZS_CLOCK_DIVISOR);
889
890 ip22zilog_convert_to_zs(up, termios->c_cflag, termios->c_iflag, brg);
891
892 if (UART_ENABLE_MS(&up->port, termios->c_cflag))
893 up->flags |= IP22ZILOG_FLAG_MODEM_STATUS;
894 else
895 up->flags &= ~IP22ZILOG_FLAG_MODEM_STATUS;
896
Linus Torvalds1da177e2005-04-16 15:20:36 -0700897 ip22zilog_maybe_update_regs(up, ZILOG_CHANNEL_FROM_PORT(port));
Thiemo Seuferc1fbac42007-07-15 23:39:59 -0700898 uart_update_timeout(port, termios->c_cflag, baud);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700899
900 spin_unlock_irqrestore(&up->port.lock, flags);
901}
902
903static const char *ip22zilog_type(struct uart_port *port)
904{
905 return "IP22-Zilog";
906}
907
908/* We do not request/release mappings of the registers here, this
909 * happens at early serial probe time.
910 */
911static void ip22zilog_release_port(struct uart_port *port)
912{
913}
914
915static int ip22zilog_request_port(struct uart_port *port)
916{
917 return 0;
918}
919
920/* These do not need to do anything interesting either. */
921static void ip22zilog_config_port(struct uart_port *port, int flags)
922{
923}
924
925/* We do not support letting the user mess with the divisor, IRQ, etc. */
926static int ip22zilog_verify_port(struct uart_port *port, struct serial_struct *ser)
927{
928 return -EINVAL;
929}
930
931static struct uart_ops ip22zilog_pops = {
932 .tx_empty = ip22zilog_tx_empty,
933 .set_mctrl = ip22zilog_set_mctrl,
934 .get_mctrl = ip22zilog_get_mctrl,
935 .stop_tx = ip22zilog_stop_tx,
936 .start_tx = ip22zilog_start_tx,
937 .stop_rx = ip22zilog_stop_rx,
938 .enable_ms = ip22zilog_enable_ms,
939 .break_ctl = ip22zilog_break_ctl,
940 .startup = ip22zilog_startup,
941 .shutdown = ip22zilog_shutdown,
942 .set_termios = ip22zilog_set_termios,
943 .type = ip22zilog_type,
944 .release_port = ip22zilog_release_port,
945 .request_port = ip22zilog_request_port,
946 .config_port = ip22zilog_config_port,
947 .verify_port = ip22zilog_verify_port,
948};
949
950static struct uart_ip22zilog_port *ip22zilog_port_table;
951static struct zilog_layout **ip22zilog_chip_regs;
952
953static struct uart_ip22zilog_port *ip22zilog_irq_chain;
954static int zilog_irq = -1;
955
956static void * __init alloc_one_table(unsigned long size)
957{
Burman Yan8f31bb32007-02-14 00:33:07 -0800958 return kzalloc(size, GFP_KERNEL);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700959}
960
961static void __init ip22zilog_alloc_tables(void)
962{
963 ip22zilog_port_table = (struct uart_ip22zilog_port *)
964 alloc_one_table(NUM_CHANNELS * sizeof(struct uart_ip22zilog_port));
965 ip22zilog_chip_regs = (struct zilog_layout **)
966 alloc_one_table(NUM_IP22ZILOG * sizeof(struct zilog_layout *));
967
968 if (ip22zilog_port_table == NULL || ip22zilog_chip_regs == NULL) {
969 panic("IP22-Zilog: Cannot allocate IP22-Zilog tables.");
970 }
971}
972
973/* Get the address of the registers for IP22-Zilog instance CHIP. */
974static struct zilog_layout * __init get_zs(int chip)
975{
976 unsigned long base;
977
978 if (chip < 0 || chip >= NUM_IP22ZILOG) {
979 panic("IP22-Zilog: Illegal chip number %d in get_zs.", chip);
980 }
981
982 /* Not probe-able, hard code it. */
983 base = (unsigned long) &sgioc->uart;
984
985 zilog_irq = SGI_SERIAL_IRQ;
986 request_mem_region(base, 8, "IP22-Zilog");
987
988 return (struct zilog_layout *) base;
989}
990
991#define ZS_PUT_CHAR_MAX_DELAY 2000 /* 10 ms */
992
993#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
Russell Kingd3587882006-03-20 20:00:09 +0000994static void ip22zilog_put_char(struct uart_port *port, int ch)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700995{
Russell Kingd3587882006-03-20 20:00:09 +0000996 struct zilog_channel *channel = ZILOG_CHANNEL_FROM_PORT(port);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700997 int loops = ZS_PUT_CHAR_MAX_DELAY;
998
999 /* This is a timed polling loop so do not switch the explicit
1000 * udelay with ZSDELAY as that is a NOP on some platforms. -DaveM
1001 */
1002 do {
1003 unsigned char val = readb(&channel->control);
1004 if (val & Tx_BUF_EMP) {
1005 ZSDELAY();
1006 break;
1007 }
1008 udelay(5);
1009 } while (--loops);
1010
1011 writeb(ch, &channel->data);
1012 ZSDELAY();
1013 ZS_WSYNC(channel);
1014}
1015
1016static void
1017ip22zilog_console_write(struct console *con, const char *s, unsigned int count)
1018{
1019 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
Linus Torvalds1da177e2005-04-16 15:20:36 -07001020 unsigned long flags;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001021
1022 spin_lock_irqsave(&up->port.lock, flags);
Russell Kingd3587882006-03-20 20:00:09 +00001023 uart_console_write(&up->port, s, count, ip22zilog_put_char);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001024 udelay(2);
1025 spin_unlock_irqrestore(&up->port.lock, flags);
1026}
1027
Linus Torvalds1da177e2005-04-16 15:20:36 -07001028static int __init ip22zilog_console_setup(struct console *con, char *options)
1029{
1030 struct uart_ip22zilog_port *up = &ip22zilog_port_table[con->index];
1031 unsigned long flags;
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -08001032 int baud = 9600, bits = 8;
1033 int parity = 'n';
1034 int flow = 'n';
Linus Torvalds1da177e2005-04-16 15:20:36 -07001035
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -08001036 up->flags |= IP22ZILOG_FLAG_IS_CONS;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001037
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -08001038 printk(KERN_INFO "Console: ttyS%d (IP22-Zilog)\n", con->index);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001039
1040 spin_lock_irqsave(&up->port.lock, flags);
1041
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -08001042 up->curregs[R15] |= BRKIE;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001043
1044 __ip22zilog_startup(up);
1045
1046 spin_unlock_irqrestore(&up->port.lock, flags);
1047
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -08001048 if (options)
1049 uart_parse_options(options, &baud, &parity, &bits, &flow);
1050 return uart_set_options(&up->port, con, baud, parity, bits, flow);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001051}
1052
1053static struct uart_driver ip22zilog_reg;
1054
1055static struct console ip22zilog_console = {
1056 .name = "ttyS",
1057 .write = ip22zilog_console_write,
1058 .device = uart_console_device,
1059 .setup = ip22zilog_console_setup,
1060 .flags = CON_PRINTBUFFER,
1061 .index = -1,
1062 .data = &ip22zilog_reg,
1063};
1064#endif /* CONFIG_SERIAL_IP22_ZILOG_CONSOLE */
1065
1066static struct uart_driver ip22zilog_reg = {
1067 .owner = THIS_MODULE,
1068 .driver_name = "serial",
Linus Torvalds1da177e2005-04-16 15:20:36 -07001069 .dev_name = "ttyS",
1070 .major = TTY_MAJOR,
1071 .minor = 64,
1072 .nr = NUM_CHANNELS,
1073#ifdef CONFIG_SERIAL_IP22_ZILOG_CONSOLE
1074 .cons = &ip22zilog_console,
1075#endif
1076};
1077
1078static void __init ip22zilog_prepare(void)
1079{
1080 struct uart_ip22zilog_port *up;
1081 struct zilog_layout *rp;
1082 int channel, chip;
1083
1084 /*
1085 * Temporary fix.
1086 */
1087 for (channel = 0; channel < NUM_CHANNELS; channel++)
1088 spin_lock_init(&ip22zilog_port_table[channel].port.lock);
1089
1090 ip22zilog_irq_chain = &ip22zilog_port_table[NUM_CHANNELS - 1];
1091 up = &ip22zilog_port_table[0];
1092 for (channel = NUM_CHANNELS - 1 ; channel > 0; channel--)
1093 up[channel].next = &up[channel - 1];
1094 up[channel].next = NULL;
1095
1096 for (chip = 0; chip < NUM_IP22ZILOG; chip++) {
1097 if (!ip22zilog_chip_regs[chip]) {
1098 ip22zilog_chip_regs[chip] = rp = get_zs(chip);
1099
1100 up[(chip * 2) + 0].port.membase = (char *) &rp->channelB;
1101 up[(chip * 2) + 1].port.membase = (char *) &rp->channelA;
1102
1103 /* In theory mapbase is the physical address ... */
1104 up[(chip * 2) + 0].port.mapbase =
1105 (unsigned long) ioremap((unsigned long) &rp->channelB, 8);
1106 up[(chip * 2) + 1].port.mapbase =
1107 (unsigned long) ioremap((unsigned long) &rp->channelA, 8);
1108 }
1109
1110 /* Channel A */
1111 up[(chip * 2) + 0].port.iotype = UPIO_MEM;
1112 up[(chip * 2) + 0].port.irq = zilog_irq;
1113 up[(chip * 2) + 0].port.uartclk = ZS_CLOCK;
1114 up[(chip * 2) + 0].port.fifosize = 1;
1115 up[(chip * 2) + 0].port.ops = &ip22zilog_pops;
1116 up[(chip * 2) + 0].port.type = PORT_IP22ZILOG;
1117 up[(chip * 2) + 0].port.flags = 0;
1118 up[(chip * 2) + 0].port.line = (chip * 2) + 0;
1119 up[(chip * 2) + 0].flags = 0;
1120
1121 /* Channel B */
1122 up[(chip * 2) + 1].port.iotype = UPIO_MEM;
1123 up[(chip * 2) + 1].port.irq = zilog_irq;
1124 up[(chip * 2) + 1].port.uartclk = ZS_CLOCK;
1125 up[(chip * 2) + 1].port.fifosize = 1;
1126 up[(chip * 2) + 1].port.ops = &ip22zilog_pops;
1127 up[(chip * 2) + 1].port.type = PORT_IP22ZILOG;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001128 up[(chip * 2) + 1].port.line = (chip * 2) + 1;
Julien BLACHEc65b15c2006-07-09 20:40:17 +02001129 up[(chip * 2) + 1].flags |= IP22ZILOG_FLAG_IS_CHANNEL_A;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001130 }
Linus Torvalds1da177e2005-04-16 15:20:36 -07001131
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -08001132 for (channel = 0; channel < NUM_CHANNELS; channel++) {
1133 struct uart_ip22zilog_port *up = &ip22zilog_port_table[channel];
1134 int brg;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001135
1136 /* Normal serial TTY. */
1137 up->parity_mask = 0xff;
1138 up->curregs[R1] = EXT_INT_ENAB | INT_ALL_Rx | TxINT_ENAB;
1139 up->curregs[R4] = PAR_EVEN | X16CLK | SB1;
1140 up->curregs[R3] = RxENAB | Rx8;
1141 up->curregs[R5] = TxENAB | Tx8;
1142 up->curregs[R9] = NV | MIE;
1143 up->curregs[R10] = NRZ;
1144 up->curregs[R11] = TCBR | RCBR;
Thomas Bogendoerfer68576cf2007-11-28 16:21:44 -08001145 brg = BPS_TO_BRG(9600, ZS_CLOCK / ZS_CLOCK_DIVISOR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001146 up->curregs[R12] = (brg & 0xff);
1147 up->curregs[R13] = (brg >> 8) & 0xff;
1148 up->curregs[R14] = BRENAB;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001149 }
1150}
1151
1152static int __init ip22zilog_ports_init(void)
1153{
1154 int ret;
1155
1156 printk(KERN_INFO "Serial: IP22 Zilog driver (%d chips).\n", NUM_IP22ZILOG);
1157
1158 ip22zilog_prepare();
1159
1160 if (request_irq(zilog_irq, ip22zilog_interrupt, 0,
1161 "IP22-Zilog", ip22zilog_irq_chain)) {
1162 panic("IP22-Zilog: Unable to register zs interrupt handler.\n");
1163 }
1164
Linus Torvalds1da177e2005-04-16 15:20:36 -07001165 ret = uart_register_driver(&ip22zilog_reg);
1166 if (ret == 0) {
1167 int i;
1168
1169 for (i = 0; i < NUM_CHANNELS; i++) {
1170 struct uart_ip22zilog_port *up = &ip22zilog_port_table[i];
1171
1172 uart_add_one_port(&ip22zilog_reg, &up->port);
1173 }
1174 }
1175
1176 return ret;
1177}
1178
1179static int __init ip22zilog_init(void)
1180{
1181 /* IP22 Zilog setup is hard coded, no probing to do. */
1182 ip22zilog_alloc_tables();
1183 ip22zilog_ports_init();
1184
1185 return 0;
1186}
1187
1188static void __exit ip22zilog_exit(void)
1189{
1190 int i;
Amol Lad6257b3b2006-09-30 23:29:22 -07001191 struct uart_ip22zilog_port *up;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001192
1193 for (i = 0; i < NUM_CHANNELS; i++) {
Amol Lad6257b3b2006-09-30 23:29:22 -07001194 up = &ip22zilog_port_table[i];
Linus Torvalds1da177e2005-04-16 15:20:36 -07001195
1196 uart_remove_one_port(&ip22zilog_reg, &up->port);
1197 }
1198
Amol Lad6257b3b2006-09-30 23:29:22 -07001199 /* Free IO mem */
1200 up = &ip22zilog_port_table[0];
1201 for (i = 0; i < NUM_IP22ZILOG; i++) {
1202 if (up[(i * 2) + 0].port.mapbase) {
1203 iounmap((void*)up[(i * 2) + 0].port.mapbase);
1204 up[(i * 2) + 0].port.mapbase = 0;
1205 }
1206 if (up[(i * 2) + 1].port.mapbase) {
1207 iounmap((void*)up[(i * 2) + 1].port.mapbase);
1208 up[(i * 2) + 1].port.mapbase = 0;
1209 }
1210 }
1211
Linus Torvalds1da177e2005-04-16 15:20:36 -07001212 uart_unregister_driver(&ip22zilog_reg);
1213}
1214
1215module_init(ip22zilog_init);
1216module_exit(ip22zilog_exit);
1217
1218/* David wrote it but I'm to blame for the bugs ... */
1219MODULE_AUTHOR("Ralf Baechle <ralf@linux-mips.org>");
1220MODULE_DESCRIPTION("SGI Zilog serial port driver");
1221MODULE_LICENSE("GPL");