Catalin Marinas | 8ad68bb | 2005-10-31 14:25:02 +0000 | [diff] [blame] | 1 | /* |
| 2 | * include/asm-arm/arch-realview/entry-macro.S |
| 3 | * |
| 4 | * Low-level IRQ helper macros for RealView platforms |
| 5 | * |
| 6 | * This file is licensed under the terms of the GNU General Public |
| 7 | * License version 2. This program is licensed "as is" without any |
| 8 | * warranty of any kind, whether express or implied. |
| 9 | */ |
| 10 | |
| 11 | #include <asm/hardware/gic.h> |
| 12 | |
| 13 | .macro disable_fiq |
| 14 | .endm |
| 15 | |
| 16 | /* |
| 17 | * The interrupt numbering scheme is defined in the |
| 18 | * interrupt controller spec. To wit: |
| 19 | * |
| 20 | * Interrupts 0-15 are IPI |
| 21 | * 16-28 are reserved |
| 22 | * 29-31 are local. We allow 30 to be used for the watchdog. |
| 23 | * 32-1020 are global |
| 24 | * 1021-1022 are reserved |
| 25 | * 1023 is "spurious" (no interrupt) |
| 26 | * |
| 27 | * For now, we ignore all local interrupts so only return an interrupt if it's |
| 28 | * between 30 and 1020. The test_for_ipi routine below will pick up on IPIs. |
| 29 | * |
| 30 | * A simple read from the controller will tell us the number of the highest |
| 31 | * priority enabled interrupt. We then just need to check whether it is in the |
| 32 | * valid range for an IRQ (30-1020 inclusive). |
| 33 | */ |
| 34 | |
| 35 | .macro get_irqnr_and_base, irqnr, irqstat, base, tmp |
| 36 | |
| 37 | ldr \base, =IO_ADDRESS(REALVIEW_GIC_CPU_BASE) |
| 38 | ldr \irqstat, [\base, #GIC_CPU_INTACK] /* bits 12-10 = src CPU, 9-0 = int # */ |
| 39 | |
| 40 | ldr \tmp, =1021 |
| 41 | |
| 42 | bic \irqnr, \irqstat, #0x1c00 |
| 43 | |
| 44 | cmp \irqnr, #29 |
| 45 | cmpcc \irqnr, \irqnr |
| 46 | cmpne \irqnr, \tmp |
| 47 | cmpcs \irqnr, \irqnr |
| 48 | |
| 49 | .endm |
Russell King | 862184f | 2005-11-07 21:05:42 +0000 | [diff] [blame] | 50 | |
| 51 | /* We assume that irqstat (the raw value of the IRQ acknowledge |
| 52 | * register) is preserved from the macro above. |
| 53 | * If there is an IPI, we immediately signal end of interrupt on the |
| 54 | * controller, since this requires the original irqstat value which |
| 55 | * we won't easily be able to recreate later. |
| 56 | */ |
| 57 | |
| 58 | .macro test_for_ipi, irqnr, irqstat, base, tmp |
| 59 | bic \irqnr, \irqstat, #0x1c00 |
| 60 | cmp \irqnr, #16 |
| 61 | strcc \irqstat, [\base, #GIC_CPU_EOI] |
| 62 | cmpcs \irqnr, \irqnr |
| 63 | .endm |