blob: 6e4c715c5d26e102200a8794980ff2391a8c5792 [file] [log] [blame]
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001/*
2 * This file is subject to the terms and conditions of the GNU General Public
3 * License. See the file "COPYING" in the main directory of this archive
4 * for more details.
5 *
6 * Copyright (C) 2005 Silicon Graphics, Inc. All Rights Reserved.
7 */
8
9/*
10 * This file contains a module version of the ioc3 serial driver. This
11 * includes all the support functions needed (support functions, etc.)
12 * and the serial driver itself.
13 */
14#include <linux/errno.h>
15#include <linux/tty.h>
Jiri Slabyee160a32011-09-01 16:20:57 +020016#include <linux/tty_flip.h>
Patrick Gefre2d0cfb52006-01-14 13:20:40 -080017#include <linux/serial.h>
18#include <linux/circ_buf.h>
19#include <linux/serial_reg.h>
20#include <linux/module.h>
21#include <linux/pci.h>
22#include <linux/serial_core.h>
23#include <linux/ioc3.h>
Tejun Heo5a0e3ad2010-03-24 17:04:11 +090024#include <linux/slab.h>
Patrick Gefre2d0cfb52006-01-14 13:20:40 -080025
26/*
27 * Interesting things about the ioc3
28 */
29
30#define LOGICAL_PORTS 2 /* rs232(0) and rs422(1) */
31#define PORTS_PER_CARD 2
32#define LOGICAL_PORTS_PER_CARD (PORTS_PER_CARD * LOGICAL_PORTS)
33#define MAX_CARDS 8
34#define MAX_LOGICAL_PORTS (LOGICAL_PORTS_PER_CARD * MAX_CARDS)
35
36/* determine given the sio_ir what port it applies to */
37#define GET_PORT_FROM_SIO_IR(_x) (_x & SIO_IR_SA) ? 0 : 1
38
39
40/*
41 * we have 2 logical ports (rs232, rs422) for each physical port
42 * evens are rs232, odds are rs422
43 */
44#define GET_PHYSICAL_PORT(_x) ((_x) >> 1)
45#define GET_LOGICAL_PORT(_x) ((_x) & 1)
46#define IS_PHYSICAL_PORT(_x) !((_x) & 1)
47#define IS_RS232(_x) !((_x) & 1)
48
49static unsigned int Num_of_ioc3_cards;
50static unsigned int Submodule_slot;
51
52/* defining this will get you LOTS of great debug info */
53//#define DEBUG_INTERRUPTS
54#define DPRINT_CONFIG(_x...) ;
55//#define DPRINT_CONFIG(_x...) printk _x
56#define NOT_PROGRESS() ;
Harvey Harrison71cc2c22008-04-30 00:55:10 -070057//#define NOT_PROGRESS() printk("%s : fails %d\n", __func__, __LINE__)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -080058
59/* number of characters we want to transmit to the lower level at a time */
60#define MAX_CHARS 256
61#define FIFO_SIZE (MAX_CHARS-1) /* it's a uchar */
62
63/* Device name we're using */
64#define DEVICE_NAME "ttySIOC"
65#define DEVICE_MAJOR 204
66#define DEVICE_MINOR 116
67
68/* flags for next_char_state */
69#define NCS_BREAK 0x1
70#define NCS_PARITY 0x2
71#define NCS_FRAMING 0x4
72#define NCS_OVERRUN 0x8
73
74/* cause we need SOME parameters ... */
75#define MIN_BAUD_SUPPORTED 1200
76#define MAX_BAUD_SUPPORTED 115200
77
78/* protocol types supported */
79#define PROTO_RS232 0
80#define PROTO_RS422 1
81
82/* Notification types */
83#define N_DATA_READY 0x01
84#define N_OUTPUT_LOWAT 0x02
85#define N_BREAK 0x04
86#define N_PARITY_ERROR 0x08
87#define N_FRAMING_ERROR 0x10
88#define N_OVERRUN_ERROR 0x20
89#define N_DDCD 0x40
90#define N_DCTS 0x80
91
92#define N_ALL_INPUT (N_DATA_READY | N_BREAK \
93 | N_PARITY_ERROR | N_FRAMING_ERROR \
94 | N_OVERRUN_ERROR | N_DDCD | N_DCTS)
95
96#define N_ALL_OUTPUT N_OUTPUT_LOWAT
97
98#define N_ALL_ERRORS (N_PARITY_ERROR | N_FRAMING_ERROR \
99 | N_OVERRUN_ERROR)
100
101#define N_ALL (N_DATA_READY | N_OUTPUT_LOWAT | N_BREAK \
102 | N_PARITY_ERROR | N_FRAMING_ERROR \
103 | N_OVERRUN_ERROR | N_DDCD | N_DCTS)
104
105#define SER_CLK_SPEED(prediv) ((22000000 << 1) / prediv)
106#define SER_DIVISOR(x, clk) (((clk) + (x) * 8) / ((x) * 16))
107#define DIVISOR_TO_BAUD(div, clk) ((clk) / 16 / (div))
108
109/* Some masks */
110#define LCR_MASK_BITS_CHAR (UART_LCR_WLEN5 | UART_LCR_WLEN6 \
111 | UART_LCR_WLEN7 | UART_LCR_WLEN8)
112#define LCR_MASK_STOP_BITS (UART_LCR_STOP)
113
114#define PENDING(_a, _p) (readl(&(_p)->vma->sio_ir) & (_a)->ic_enable)
115
116#define RING_BUF_SIZE 4096
117#define BUF_SIZE_BIT SBBR_L_SIZE
118#define PROD_CONS_MASK PROD_CONS_PTR_4K
119
120#define TOTAL_RING_BUF_SIZE (RING_BUF_SIZE * 4)
121
122/* driver specific - one per card */
123struct ioc3_card {
124 struct {
125 /* uart ports are allocated here */
126 struct uart_port icp_uart_port[LOGICAL_PORTS];
127 /* the ioc3_port used for this port */
128 struct ioc3_port *icp_port;
129 } ic_port[PORTS_PER_CARD];
130 /* currently enabled interrupts */
131 uint32_t ic_enable;
132};
133
134/* Local port info for each IOC3 serial port */
135struct ioc3_port {
136 /* handy reference material */
137 struct uart_port *ip_port;
138 struct ioc3_card *ip_card;
139 struct ioc3_driver_data *ip_idd;
140 struct ioc3_submodule *ip_is;
141
142 /* pci mem addresses for this port */
143 struct ioc3_serialregs __iomem *ip_serial_regs;
144 struct ioc3_uartregs __iomem *ip_uart_regs;
145
146 /* Ring buffer page for this port */
147 dma_addr_t ip_dma_ringbuf;
148 /* vaddr of ring buffer */
149 struct ring_buffer *ip_cpu_ringbuf;
150
151 /* Rings for this port */
152 struct ring *ip_inring;
153 struct ring *ip_outring;
154
155 /* Hook to port specific values */
156 struct port_hooks *ip_hooks;
157
158 spinlock_t ip_lock;
159
160 /* Various rx/tx parameters */
161 int ip_baud;
162 int ip_tx_lowat;
163 int ip_rx_timeout;
164
165 /* Copy of notification bits */
166 int ip_notify;
167
168 /* Shadow copies of various registers so we don't need to PIO
169 * read them constantly
170 */
171 uint32_t ip_sscr;
172 uint32_t ip_tx_prod;
173 uint32_t ip_rx_cons;
174 unsigned char ip_flags;
175};
176
177/* tx low water mark. We need to notify the driver whenever tx is getting
178 * close to empty so it can refill the tx buffer and keep things going.
179 * Let's assume that if we interrupt 1 ms before the tx goes idle, we'll
180 * have no trouble getting in more chars in time (I certainly hope so).
181 */
182#define TX_LOWAT_LATENCY 1000
183#define TX_LOWAT_HZ (1000000 / TX_LOWAT_LATENCY)
184#define TX_LOWAT_CHARS(baud) (baud / 10 / TX_LOWAT_HZ)
185
186/* Flags per port */
187#define INPUT_HIGH 0x01
188 /* used to signify that we have turned off the rx_high
189 * temporarily - we need to drain the fifo and don't
190 * want to get blasted with interrupts.
191 */
192#define DCD_ON 0x02
193 /* DCD state is on */
194#define LOWAT_WRITTEN 0x04
195#define READ_ABORTED 0x08
196 /* the read was aborted - used to avaoid infinate looping
197 * in the interrupt handler
198 */
199#define INPUT_ENABLE 0x10
200
201/* Since each port has different register offsets and bitmasks
202 * for everything, we'll store those that we need in tables so we
203 * don't have to be constantly checking the port we are dealing with.
204 */
205struct port_hooks {
206 uint32_t intr_delta_dcd;
207 uint32_t intr_delta_cts;
208 uint32_t intr_tx_mt;
209 uint32_t intr_rx_timer;
210 uint32_t intr_rx_high;
211 uint32_t intr_tx_explicit;
212 uint32_t intr_clear;
213 uint32_t intr_all;
214 char rs422_select_pin;
215};
216
217static struct port_hooks hooks_array[PORTS_PER_CARD] = {
218 /* values for port A */
219 {
220 .intr_delta_dcd = SIO_IR_SA_DELTA_DCD,
221 .intr_delta_cts = SIO_IR_SA_DELTA_CTS,
222 .intr_tx_mt = SIO_IR_SA_TX_MT,
223 .intr_rx_timer = SIO_IR_SA_RX_TIMER,
224 .intr_rx_high = SIO_IR_SA_RX_HIGH,
225 .intr_tx_explicit = SIO_IR_SA_TX_EXPLICIT,
226 .intr_clear = (SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL
227 | SIO_IR_SA_RX_HIGH
228 | SIO_IR_SA_RX_TIMER
229 | SIO_IR_SA_DELTA_DCD
230 | SIO_IR_SA_DELTA_CTS
231 | SIO_IR_SA_INT
232 | SIO_IR_SA_TX_EXPLICIT
233 | SIO_IR_SA_MEMERR),
234 .intr_all = SIO_IR_SA,
235 .rs422_select_pin = GPPR_UARTA_MODESEL_PIN,
236 },
237
238 /* values for port B */
239 {
240 .intr_delta_dcd = SIO_IR_SB_DELTA_DCD,
241 .intr_delta_cts = SIO_IR_SB_DELTA_CTS,
242 .intr_tx_mt = SIO_IR_SB_TX_MT,
243 .intr_rx_timer = SIO_IR_SB_RX_TIMER,
244 .intr_rx_high = SIO_IR_SB_RX_HIGH,
245 .intr_tx_explicit = SIO_IR_SB_TX_EXPLICIT,
246 .intr_clear = (SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL
247 | SIO_IR_SB_RX_HIGH
248 | SIO_IR_SB_RX_TIMER
249 | SIO_IR_SB_DELTA_DCD
250 | SIO_IR_SB_DELTA_CTS
251 | SIO_IR_SB_INT
252 | SIO_IR_SB_TX_EXPLICIT
253 | SIO_IR_SB_MEMERR),
254 .intr_all = SIO_IR_SB,
255 .rs422_select_pin = GPPR_UARTB_MODESEL_PIN,
256 }
257};
258
259struct ring_entry {
260 union {
261 struct {
262 uint32_t alldata;
263 uint32_t allsc;
264 } all;
265 struct {
266 char data[4]; /* data bytes */
267 char sc[4]; /* status/control */
268 } s;
269 } u;
270};
271
272/* Test the valid bits in any of the 4 sc chars using "allsc" member */
273#define RING_ANY_VALID \
274 ((uint32_t)(RXSB_MODEM_VALID | RXSB_DATA_VALID) * 0x01010101)
275
276#define ring_sc u.s.sc
277#define ring_data u.s.data
278#define ring_allsc u.all.allsc
279
280/* Number of entries per ring buffer. */
281#define ENTRIES_PER_RING (RING_BUF_SIZE / (int) sizeof(struct ring_entry))
282
283/* An individual ring */
284struct ring {
285 struct ring_entry entries[ENTRIES_PER_RING];
286};
287
288/* The whole enchilada */
289struct ring_buffer {
290 struct ring TX_A;
291 struct ring RX_A;
292 struct ring TX_B;
293 struct ring RX_B;
294};
295
296/* Get a ring from a port struct */
297#define RING(_p, _wh) &(((struct ring_buffer *)((_p)->ip_cpu_ringbuf))->_wh)
298
299/* for Infinite loop detection */
300#define MAXITER 10000000
301
302
303/**
304 * set_baud - Baud rate setting code
305 * @port: port to set
306 * @baud: baud rate to use
307 */
308static int set_baud(struct ioc3_port *port, int baud)
309{
310 int divisor;
311 int actual_baud;
312 int diff;
313 int lcr, prediv;
314 struct ioc3_uartregs __iomem *uart;
315
316 for (prediv = 6; prediv < 64; prediv++) {
317 divisor = SER_DIVISOR(baud, SER_CLK_SPEED(prediv));
318 if (!divisor)
319 continue; /* invalid divisor */
320 actual_baud = DIVISOR_TO_BAUD(divisor, SER_CLK_SPEED(prediv));
321
322 diff = actual_baud - baud;
323 if (diff < 0)
324 diff = -diff;
325
326 /* if we're within 1% we've found a match */
327 if (diff * 100 <= actual_baud)
328 break;
329 }
330
331 /* if the above loop completed, we didn't match
332 * the baud rate. give up.
333 */
334 if (prediv == 64) {
335 NOT_PROGRESS();
336 return 1;
337 }
338
339 uart = port->ip_uart_regs;
340 lcr = readb(&uart->iu_lcr);
341
342 writeb(lcr | UART_LCR_DLAB, &uart->iu_lcr);
343 writeb((unsigned char)divisor, &uart->iu_dll);
344 writeb((unsigned char)(divisor >> 8), &uart->iu_dlm);
345 writeb((unsigned char)prediv, &uart->iu_scr);
346 writeb((unsigned char)lcr, &uart->iu_lcr);
347
348 return 0;
349}
350
351/**
352 * get_ioc3_port - given a uart port, return the control structure
353 * @the_port: uart port to find
354 */
355static struct ioc3_port *get_ioc3_port(struct uart_port *the_port)
356{
357 struct ioc3_driver_data *idd = dev_get_drvdata(the_port->dev);
358 struct ioc3_card *card_ptr = idd->data[Submodule_slot];
359 int ii, jj;
360
361 if (!card_ptr) {
362 NOT_PROGRESS();
363 return NULL;
364 }
365 for (ii = 0; ii < PORTS_PER_CARD; ii++) {
366 for (jj = 0; jj < LOGICAL_PORTS; jj++) {
367 if (the_port == &card_ptr->ic_port[ii].icp_uart_port[jj])
368 return card_ptr->ic_port[ii].icp_port;
369 }
370 }
371 NOT_PROGRESS();
372 return NULL;
373}
374
375/**
376 * port_init - Initialize the sio and ioc3 hardware for a given port
377 * called per port from attach...
378 * @port: port to initialize
379 */
380static int inline port_init(struct ioc3_port *port)
381{
382 uint32_t sio_cr;
383 struct port_hooks *hooks = port->ip_hooks;
384 struct ioc3_uartregs __iomem *uart;
385 int reset_loop_counter = 0xfffff;
386 struct ioc3_driver_data *idd = port->ip_idd;
387
388 /* Idle the IOC3 serial interface */
389 writel(SSCR_RESET, &port->ip_serial_regs->sscr);
390
391 /* Wait until any pending bus activity for this port has ceased */
392 do {
393 sio_cr = readl(&idd->vma->sio_cr);
394 if (reset_loop_counter-- <= 0) {
395 printk(KERN_WARNING
396 "IOC3 unable to come out of reset"
397 " scr 0x%x\n", sio_cr);
398 return -1;
399 }
400 } while (!(sio_cr & SIO_CR_ARB_DIAG_IDLE) &&
401 (((sio_cr &= SIO_CR_ARB_DIAG) == SIO_CR_ARB_DIAG_TXA)
402 || sio_cr == SIO_CR_ARB_DIAG_TXB
403 || sio_cr == SIO_CR_ARB_DIAG_RXA
404 || sio_cr == SIO_CR_ARB_DIAG_RXB));
405
406 /* Finish reset sequence */
407 writel(0, &port->ip_serial_regs->sscr);
408
409 /* Once RESET is done, reload cached tx_prod and rx_cons values
410 * and set rings to empty by making prod == cons
411 */
412 port->ip_tx_prod = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
413 writel(port->ip_tx_prod, &port->ip_serial_regs->stpir);
414 port->ip_rx_cons = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
415 writel(port->ip_rx_cons | SRCIR_ARM, &port->ip_serial_regs->srcir);
416
417 /* Disable interrupts for this 16550 */
418 uart = port->ip_uart_regs;
419 writeb(0, &uart->iu_lcr);
420 writeb(0, &uart->iu_ier);
421
422 /* Set the default baud */
423 set_baud(port, port->ip_baud);
424
425 /* Set line control to 8 bits no parity */
426 writeb(UART_LCR_WLEN8 | 0, &uart->iu_lcr);
427 /* UART_LCR_STOP == 1 stop */
428
429 /* Enable the FIFOs */
430 writeb(UART_FCR_ENABLE_FIFO, &uart->iu_fcr);
431 /* then reset 16550 FIFOs */
432 writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
433 &uart->iu_fcr);
434
435 /* Clear modem control register */
436 writeb(0, &uart->iu_mcr);
437
438 /* Clear deltas in modem status register */
439 writel(0, &port->ip_serial_regs->shadow);
440
441 /* Only do this once per port pair */
442 if (port->ip_hooks == &hooks_array[0]) {
443 unsigned long ring_pci_addr;
444 uint32_t __iomem *sbbr_l, *sbbr_h;
445
446 sbbr_l = &idd->vma->sbbr_l;
447 sbbr_h = &idd->vma->sbbr_h;
448 ring_pci_addr = (unsigned long __iomem)port->ip_dma_ringbuf;
449 DPRINT_CONFIG(("%s: ring_pci_addr 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700450 __func__, (void *)ring_pci_addr));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800451
452 writel((unsigned int)((uint64_t) ring_pci_addr >> 32), sbbr_h);
453 writel((unsigned int)ring_pci_addr | BUF_SIZE_BIT, sbbr_l);
454 }
455
456 /* Set the receive timeout value to 10 msec */
457 writel(SRTR_HZ / 100, &port->ip_serial_regs->srtr);
458
459 /* Set rx threshold, enable DMA */
460 /* Set high water mark at 3/4 of full ring */
461 port->ip_sscr = (ENTRIES_PER_RING * 3 / 4);
462
463 /* uart experiences pauses at high baud rate reducing actual
464 * throughput by 10% or so unless we enable high speed polling
465 * XXX when this hardware bug is resolved we should revert to
466 * normal polling speed
467 */
468 port->ip_sscr |= SSCR_HIGH_SPD;
469
470 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
471
472 /* Disable and clear all serial related interrupt bits */
473 port->ip_card->ic_enable &= ~hooks->intr_clear;
474 ioc3_disable(port->ip_is, idd, hooks->intr_clear);
475 ioc3_ack(port->ip_is, idd, hooks->intr_clear);
476 return 0;
477}
478
479/**
480 * enable_intrs - enable interrupts
481 * @port: port to enable
482 * @mask: mask to use
483 */
484static void enable_intrs(struct ioc3_port *port, uint32_t mask)
485{
486 if ((port->ip_card->ic_enable & mask) != mask) {
487 port->ip_card->ic_enable |= mask;
488 ioc3_enable(port->ip_is, port->ip_idd, mask);
489 }
490}
491
492/**
493 * local_open - local open a port
494 * @port: port to open
495 */
496static inline int local_open(struct ioc3_port *port)
497{
498 int spiniter = 0;
499
500 port->ip_flags = INPUT_ENABLE;
501
502 /* Pause the DMA interface if necessary */
503 if (port->ip_sscr & SSCR_DMA_EN) {
504 writel(port->ip_sscr | SSCR_DMA_PAUSE,
505 &port->ip_serial_regs->sscr);
506 while ((readl(&port->ip_serial_regs->sscr)
507 & SSCR_PAUSE_STATE) == 0) {
508 spiniter++;
509 if (spiniter > MAXITER) {
510 NOT_PROGRESS();
511 return -1;
512 }
513 }
514 }
515
516 /* Reset the input fifo. If the uart received chars while the port
517 * was closed and DMA is not enabled, the uart may have a bunch of
518 * chars hanging around in its rx fifo which will not be discarded
519 * by rclr in the upper layer. We must get rid of them here.
520 */
521 writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR,
522 &port->ip_uart_regs->iu_fcr);
523
524 writeb(UART_LCR_WLEN8, &port->ip_uart_regs->iu_lcr);
525 /* UART_LCR_STOP == 1 stop */
526
527 /* Re-enable DMA, set default threshold to intr whenever there is
528 * data available.
529 */
530 port->ip_sscr &= ~SSCR_RX_THRESHOLD;
531 port->ip_sscr |= 1; /* default threshold */
532
533 /* Plug in the new sscr. This implicitly clears the DMA_PAUSE
534 * flag if it was set above
535 */
536 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
537 port->ip_tx_lowat = 1;
538 return 0;
539}
540
541/**
542 * set_rx_timeout - Set rx timeout and threshold values.
543 * @port: port to use
544 * @timeout: timeout value in ticks
545 */
546static inline int set_rx_timeout(struct ioc3_port *port, int timeout)
547{
548 int threshold;
549
550 port->ip_rx_timeout = timeout;
551
552 /* Timeout is in ticks. Let's figure out how many chars we
553 * can receive at the current baud rate in that interval
554 * and set the rx threshold to that amount. There are 4 chars
555 * per ring entry, so we'll divide the number of chars that will
556 * arrive in timeout by 4.
557 * So .... timeout * baud / 10 / HZ / 4, with HZ = 100.
558 */
559 threshold = timeout * port->ip_baud / 4000;
560 if (threshold == 0)
561 threshold = 1; /* otherwise we'll intr all the time! */
562
563 if ((unsigned)threshold > (unsigned)SSCR_RX_THRESHOLD)
564 return 1;
565
566 port->ip_sscr &= ~SSCR_RX_THRESHOLD;
567 port->ip_sscr |= threshold;
568 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
569
570 /* Now set the rx timeout to the given value
571 * again timeout * SRTR_HZ / HZ
572 */
573 timeout = timeout * SRTR_HZ / 100;
574 if (timeout > SRTR_CNT)
575 timeout = SRTR_CNT;
576 writel(timeout, &port->ip_serial_regs->srtr);
577 return 0;
578}
579
580/**
581 * config_port - config the hardware
582 * @port: port to config
583 * @baud: baud rate for the port
584 * @byte_size: data size
585 * @stop_bits: number of stop bits
586 * @parenb: parity enable ?
587 * @parodd: odd parity ?
588 */
589static inline int
590config_port(struct ioc3_port *port,
591 int baud, int byte_size, int stop_bits, int parenb, int parodd)
592{
593 char lcr, sizebits;
594 int spiniter = 0;
595
596 DPRINT_CONFIG(("%s: line %d baud %d byte_size %d stop %d parenb %d "
597 "parodd %d\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700598 __func__, ((struct uart_port *)port->ip_port)->line,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800599 baud, byte_size, stop_bits, parenb, parodd));
600
601 if (set_baud(port, baud))
602 return 1;
603
604 switch (byte_size) {
605 case 5:
606 sizebits = UART_LCR_WLEN5;
607 break;
608 case 6:
609 sizebits = UART_LCR_WLEN6;
610 break;
611 case 7:
612 sizebits = UART_LCR_WLEN7;
613 break;
614 case 8:
615 sizebits = UART_LCR_WLEN8;
616 break;
617 default:
618 return 1;
619 }
620
621 /* Pause the DMA interface if necessary */
622 if (port->ip_sscr & SSCR_DMA_EN) {
623 writel(port->ip_sscr | SSCR_DMA_PAUSE,
624 &port->ip_serial_regs->sscr);
625 while ((readl(&port->ip_serial_regs->sscr)
626 & SSCR_PAUSE_STATE) == 0) {
627 spiniter++;
628 if (spiniter > MAXITER)
629 return -1;
630 }
631 }
632
633 /* Clear relevant fields in lcr */
634 lcr = readb(&port->ip_uart_regs->iu_lcr);
635 lcr &= ~(LCR_MASK_BITS_CHAR | UART_LCR_EPAR |
636 UART_LCR_PARITY | LCR_MASK_STOP_BITS);
637
638 /* Set byte size in lcr */
639 lcr |= sizebits;
640
641 /* Set parity */
642 if (parenb) {
643 lcr |= UART_LCR_PARITY;
644 if (!parodd)
645 lcr |= UART_LCR_EPAR;
646 }
647
648 /* Set stop bits */
649 if (stop_bits)
650 lcr |= UART_LCR_STOP /* 2 stop bits */ ;
651
652 writeb(lcr, &port->ip_uart_regs->iu_lcr);
653
654 /* Re-enable the DMA interface if necessary */
655 if (port->ip_sscr & SSCR_DMA_EN) {
656 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
657 }
658 port->ip_baud = baud;
659
660 /* When we get within this number of ring entries of filling the
661 * entire ring on tx, place an EXPLICIT intr to generate a lowat
662 * notification when output has drained.
663 */
664 port->ip_tx_lowat = (TX_LOWAT_CHARS(baud) + 3) / 4;
665 if (port->ip_tx_lowat == 0)
666 port->ip_tx_lowat = 1;
667
668 set_rx_timeout(port, 2);
669 return 0;
670}
671
672/**
673 * do_write - Write bytes to the port. Returns the number of bytes
674 * actually written. Called from transmit_chars
675 * @port: port to use
676 * @buf: the stuff to write
677 * @len: how many bytes in 'buf'
678 */
679static inline int do_write(struct ioc3_port *port, char *buf, int len)
680{
681 int prod_ptr, cons_ptr, total = 0;
682 struct ring *outring;
683 struct ring_entry *entry;
684 struct port_hooks *hooks = port->ip_hooks;
685
686 BUG_ON(!(len >= 0));
687
688 prod_ptr = port->ip_tx_prod;
689 cons_ptr = readl(&port->ip_serial_regs->stcir) & PROD_CONS_MASK;
690 outring = port->ip_outring;
691
692 /* Maintain a 1-entry red-zone. The ring buffer is full when
693 * (cons - prod) % ring_size is 1. Rather than do this subtraction
694 * in the body of the loop, I'll do it now.
695 */
696 cons_ptr = (cons_ptr - (int)sizeof(struct ring_entry)) & PROD_CONS_MASK;
697
698 /* Stuff the bytes into the output */
699 while ((prod_ptr != cons_ptr) && (len > 0)) {
700 int xx;
701
702 /* Get 4 bytes (one ring entry) at a time */
703 entry = (struct ring_entry *)((caddr_t) outring + prod_ptr);
704
705 /* Invalidate all entries */
706 entry->ring_allsc = 0;
707
708 /* Copy in some bytes */
709 for (xx = 0; (xx < 4) && (len > 0); xx++) {
710 entry->ring_data[xx] = *buf++;
711 entry->ring_sc[xx] = TXCB_VALID;
712 len--;
713 total++;
714 }
715
716 /* If we are within some small threshold of filling up the
717 * entire ring buffer, we must place an EXPLICIT intr here
718 * to generate a lowat interrupt in case we subsequently
719 * really do fill up the ring and the caller goes to sleep.
720 * No need to place more than one though.
721 */
722 if (!(port->ip_flags & LOWAT_WRITTEN) &&
723 ((cons_ptr - prod_ptr) & PROD_CONS_MASK)
724 <= port->ip_tx_lowat * (int)sizeof(struct ring_entry)) {
725 port->ip_flags |= LOWAT_WRITTEN;
726 entry->ring_sc[0] |= TXCB_INT_WHEN_DONE;
727 }
728
729 /* Go on to next entry */
730 prod_ptr += sizeof(struct ring_entry);
731 prod_ptr &= PROD_CONS_MASK;
732 }
733
734 /* If we sent something, start DMA if necessary */
735 if (total > 0 && !(port->ip_sscr & SSCR_DMA_EN)) {
736 port->ip_sscr |= SSCR_DMA_EN;
737 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
738 }
739
740 /* Store the new producer pointer. If tx is disabled, we stuff the
741 * data into the ring buffer, but we don't actually start tx.
742 */
743 if (!uart_tx_stopped(port->ip_port)) {
744 writel(prod_ptr, &port->ip_serial_regs->stpir);
745
746 /* If we are now transmitting, enable tx_mt interrupt so we
747 * can disable DMA if necessary when the tx finishes.
748 */
749 if (total > 0)
750 enable_intrs(port, hooks->intr_tx_mt);
751 }
752 port->ip_tx_prod = prod_ptr;
753
754 return total;
755}
756
757/**
758 * disable_intrs - disable interrupts
759 * @port: port to enable
760 * @mask: mask to use
761 */
762static inline void disable_intrs(struct ioc3_port *port, uint32_t mask)
763{
764 if (port->ip_card->ic_enable & mask) {
765 ioc3_disable(port->ip_is, port->ip_idd, mask);
766 port->ip_card->ic_enable &= ~mask;
767 }
768}
769
770/**
771 * set_notification - Modify event notification
772 * @port: port to use
773 * @mask: events mask
774 * @set_on: set ?
775 */
776static int set_notification(struct ioc3_port *port, int mask, int set_on)
777{
778 struct port_hooks *hooks = port->ip_hooks;
779 uint32_t intrbits, sscrbits;
780
781 BUG_ON(!mask);
782
783 intrbits = sscrbits = 0;
784
785 if (mask & N_DATA_READY)
786 intrbits |= (hooks->intr_rx_timer | hooks->intr_rx_high);
787 if (mask & N_OUTPUT_LOWAT)
788 intrbits |= hooks->intr_tx_explicit;
789 if (mask & N_DDCD) {
790 intrbits |= hooks->intr_delta_dcd;
791 sscrbits |= SSCR_RX_RING_DCD;
792 }
793 if (mask & N_DCTS)
794 intrbits |= hooks->intr_delta_cts;
795
796 if (set_on) {
797 enable_intrs(port, intrbits);
798 port->ip_notify |= mask;
799 port->ip_sscr |= sscrbits;
800 } else {
801 disable_intrs(port, intrbits);
802 port->ip_notify &= ~mask;
803 port->ip_sscr &= ~sscrbits;
804 }
805
806 /* We require DMA if either DATA_READY or DDCD notification is
807 * currently requested. If neither of these is requested and
808 * there is currently no tx in progress, DMA may be disabled.
809 */
810 if (port->ip_notify & (N_DATA_READY | N_DDCD))
811 port->ip_sscr |= SSCR_DMA_EN;
812 else if (!(port->ip_card->ic_enable & hooks->intr_tx_mt))
813 port->ip_sscr &= ~SSCR_DMA_EN;
814
815 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
816 return 0;
817}
818
819/**
820 * set_mcr - set the master control reg
821 * @the_port: port to use
822 * @mask1: mcr mask
823 * @mask2: shadow mask
824 */
825static inline int set_mcr(struct uart_port *the_port,
826 int mask1, int mask2)
827{
828 struct ioc3_port *port = get_ioc3_port(the_port);
829 uint32_t shadow;
830 int spiniter = 0;
831 char mcr;
832
833 if (!port)
834 return -1;
835
836 /* Pause the DMA interface if necessary */
837 if (port->ip_sscr & SSCR_DMA_EN) {
838 writel(port->ip_sscr | SSCR_DMA_PAUSE,
839 &port->ip_serial_regs->sscr);
840 while ((readl(&port->ip_serial_regs->sscr)
841 & SSCR_PAUSE_STATE) == 0) {
842 spiniter++;
843 if (spiniter > MAXITER)
844 return -1;
845 }
846 }
847 shadow = readl(&port->ip_serial_regs->shadow);
848 mcr = (shadow & 0xff000000) >> 24;
849
850 /* Set new value */
851 mcr |= mask1;
852 shadow |= mask2;
853 writeb(mcr, &port->ip_uart_regs->iu_mcr);
854 writel(shadow, &port->ip_serial_regs->shadow);
855
856 /* Re-enable the DMA interface if necessary */
857 if (port->ip_sscr & SSCR_DMA_EN) {
858 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
859 }
860 return 0;
861}
862
863/**
864 * ioc3_set_proto - set the protocol for the port
865 * @port: port to use
866 * @proto: protocol to use
867 */
868static int ioc3_set_proto(struct ioc3_port *port, int proto)
869{
870 struct port_hooks *hooks = port->ip_hooks;
871
872 switch (proto) {
873 default:
874 case PROTO_RS232:
875 /* Clear the appropriate GIO pin */
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700876 DPRINT_CONFIG(("%s: rs232\n", __func__));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800877 writel(0, (&port->ip_idd->vma->gppr[0]
878 + hooks->rs422_select_pin));
879 break;
880
881 case PROTO_RS422:
882 /* Set the appropriate GIO pin */
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700883 DPRINT_CONFIG(("%s: rs422\n", __func__));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800884 writel(1, (&port->ip_idd->vma->gppr[0]
885 + hooks->rs422_select_pin));
886 break;
887 }
888 return 0;
889}
890
891/**
892 * transmit_chars - upper level write, called with the_port->lock
893 * @the_port: port to write
894 */
895static void transmit_chars(struct uart_port *the_port)
896{
897 int xmit_count, tail, head;
898 int result;
899 char *start;
900 struct tty_struct *tty;
901 struct ioc3_port *port = get_ioc3_port(the_port);
Alan Coxebd2c8f2009-09-19 13:13:28 -0700902 struct uart_state *state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800903
904 if (!the_port)
905 return;
906 if (!port)
907 return;
908
Alan Coxebd2c8f2009-09-19 13:13:28 -0700909 state = the_port->state;
910 tty = state->port.tty;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800911
Alan Coxebd2c8f2009-09-19 13:13:28 -0700912 if (uart_circ_empty(&state->xmit) || uart_tx_stopped(the_port)) {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800913 /* Nothing to do or hw stopped */
914 set_notification(port, N_ALL_OUTPUT, 0);
915 return;
916 }
917
Alan Coxebd2c8f2009-09-19 13:13:28 -0700918 head = state->xmit.head;
919 tail = state->xmit.tail;
920 start = (char *)&state->xmit.buf[tail];
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800921
922 /* write out all the data or until the end of the buffer */
923 xmit_count = (head < tail) ? (UART_XMIT_SIZE - tail) : (head - tail);
924 if (xmit_count > 0) {
925 result = do_write(port, start, xmit_count);
926 if (result > 0) {
927 /* booking */
928 xmit_count -= result;
929 the_port->icount.tx += result;
930 /* advance the pointers */
931 tail += result;
932 tail &= UART_XMIT_SIZE - 1;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700933 state->xmit.tail = tail;
934 start = (char *)&state->xmit.buf[tail];
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800935 }
936 }
Alan Coxebd2c8f2009-09-19 13:13:28 -0700937 if (uart_circ_chars_pending(&state->xmit) < WAKEUP_CHARS)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800938 uart_write_wakeup(the_port);
939
Alan Coxebd2c8f2009-09-19 13:13:28 -0700940 if (uart_circ_empty(&state->xmit)) {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800941 set_notification(port, N_OUTPUT_LOWAT, 0);
942 } else {
943 set_notification(port, N_OUTPUT_LOWAT, 1);
944 }
945}
946
947/**
948 * ioc3_change_speed - change the speed of the port
949 * @the_port: port to change
950 * @new_termios: new termios settings
951 * @old_termios: old termios settings
952 */
953static void
954ioc3_change_speed(struct uart_port *the_port,
Alan Cox606d0992006-12-08 02:38:45 -0800955 struct ktermios *new_termios, struct ktermios *old_termios)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800956{
957 struct ioc3_port *port = get_ioc3_port(the_port);
Alan Coxeab4f5a2010-06-01 22:52:52 +0200958 unsigned int cflag, iflag;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800959 int baud;
960 int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700961 struct uart_state *state = the_port->state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800962
963 cflag = new_termios->c_cflag;
Alan Coxeab4f5a2010-06-01 22:52:52 +0200964 iflag = new_termios->c_iflag;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800965
966 switch (cflag & CSIZE) {
967 case CS5:
968 new_data = 5;
969 break;
970 case CS6:
971 new_data = 6;
972 break;
973 case CS7:
974 new_data = 7;
975 break;
976 case CS8:
977 new_data = 8;
978 break;
979 default:
980 /* cuz we always need a default ... */
981 new_data = 5;
982 break;
983 }
984 if (cflag & CSTOPB) {
985 new_stop = 1;
986 }
987 if (cflag & PARENB) {
988 new_parity_enable = 1;
989 if (cflag & PARODD)
990 new_parity = 1;
991 }
992 baud = uart_get_baud_rate(the_port, new_termios, old_termios,
993 MIN_BAUD_SUPPORTED, MAX_BAUD_SUPPORTED);
Harvey Harrison71cc2c22008-04-30 00:55:10 -0700994 DPRINT_CONFIG(("%s: returned baud %d for line %d\n", __func__, baud,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -0800995 the_port->line));
996
997 if (!the_port->fifosize)
998 the_port->fifosize = FIFO_SIZE;
999 uart_update_timeout(the_port, cflag, baud);
1000
1001 the_port->ignore_status_mask = N_ALL_INPUT;
1002
Jiri Slabyd6c53c02013-01-03 15:53:05 +01001003 state->port.low_latency = 1;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001004
Alan Coxeab4f5a2010-06-01 22:52:52 +02001005 if (iflag & IGNPAR)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001006 the_port->ignore_status_mask &= ~(N_PARITY_ERROR
1007 | N_FRAMING_ERROR);
Alan Coxeab4f5a2010-06-01 22:52:52 +02001008 if (iflag & IGNBRK) {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001009 the_port->ignore_status_mask &= ~N_BREAK;
Alan Coxeab4f5a2010-06-01 22:52:52 +02001010 if (iflag & IGNPAR)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001011 the_port->ignore_status_mask &= ~N_OVERRUN_ERROR;
1012 }
1013 if (!(cflag & CREAD)) {
1014 /* ignore everything */
1015 the_port->ignore_status_mask &= ~N_DATA_READY;
1016 }
1017
1018 if (cflag & CRTSCTS) {
1019 /* enable hardware flow control */
1020 port->ip_sscr |= SSCR_HFC_EN;
1021 }
1022 else {
1023 /* disable hardware flow control */
1024 port->ip_sscr &= ~SSCR_HFC_EN;
1025 }
1026 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
1027
1028 /* Set the configuration and proper notification call */
1029 DPRINT_CONFIG(("%s : port 0x%p line %d cflag 0%o "
1030 "config_port(baud %d data %d stop %d penable %d "
1031 " parity %d), notification 0x%x\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001032 __func__, (void *)port, the_port->line, cflag, baud,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001033 new_data, new_stop, new_parity_enable, new_parity,
1034 the_port->ignore_status_mask));
1035
1036 if ((config_port(port, baud, /* baud */
1037 new_data, /* byte size */
1038 new_stop, /* stop bits */
1039 new_parity_enable, /* set parity */
1040 new_parity)) >= 0) { /* parity 1==odd */
1041 set_notification(port, the_port->ignore_status_mask, 1);
1042 }
1043}
1044
1045/**
1046 * ic3_startup_local - Start up the serial port - returns >= 0 if no errors
1047 * @the_port: Port to operate on
1048 */
1049static inline int ic3_startup_local(struct uart_port *the_port)
1050{
1051 struct ioc3_port *port;
1052
1053 if (!the_port) {
1054 NOT_PROGRESS();
1055 return -1;
1056 }
1057
1058 port = get_ioc3_port(the_port);
1059 if (!port) {
1060 NOT_PROGRESS();
1061 return -1;
1062 }
1063
1064 local_open(port);
1065
1066 /* set the protocol */
1067 ioc3_set_proto(port, IS_RS232(the_port->line) ? PROTO_RS232 :
1068 PROTO_RS422);
1069 return 0;
1070}
1071
1072/*
1073 * ioc3_cb_output_lowat - called when the output low water mark is hit
1074 * @port: port to output
1075 */
1076static void ioc3_cb_output_lowat(struct ioc3_port *port)
1077{
1078 unsigned long pflags;
1079
1080 /* the_port->lock is set on the call here */
1081 if (port->ip_port) {
1082 spin_lock_irqsave(&port->ip_port->lock, pflags);
1083 transmit_chars(port->ip_port);
1084 spin_unlock_irqrestore(&port->ip_port->lock, pflags);
1085 }
1086}
1087
1088/*
1089 * ioc3_cb_post_ncs - called for some basic errors
1090 * @port: port to use
1091 * @ncs: event
1092 */
1093static void ioc3_cb_post_ncs(struct uart_port *the_port, int ncs)
1094{
1095 struct uart_icount *icount;
1096
1097 icount = &the_port->icount;
1098
1099 if (ncs & NCS_BREAK)
1100 icount->brk++;
1101 if (ncs & NCS_FRAMING)
1102 icount->frame++;
1103 if (ncs & NCS_OVERRUN)
1104 icount->overrun++;
1105 if (ncs & NCS_PARITY)
1106 icount->parity++;
1107}
1108
1109/**
1110 * do_read - Read in bytes from the port. Return the number of bytes
1111 * actually read.
1112 * @the_port: port to use
1113 * @buf: place to put the stuff we read
1114 * @len: how big 'buf' is
1115 */
1116
1117static inline int do_read(struct uart_port *the_port, char *buf, int len)
1118{
1119 int prod_ptr, cons_ptr, total;
1120 struct ioc3_port *port = get_ioc3_port(the_port);
1121 struct ring *inring;
1122 struct ring_entry *entry;
Wei Yongjun3d39aa62012-09-07 14:53:49 +08001123 struct port_hooks *hooks;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001124 int byte_num;
1125 char *sc;
1126 int loop_counter;
1127
1128 BUG_ON(!(len >= 0));
1129 BUG_ON(!port);
Wei Yongjun3d39aa62012-09-07 14:53:49 +08001130 hooks = port->ip_hooks;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001131
1132 /* There is a nasty timing issue in the IOC3. When the rx_timer
1133 * expires or the rx_high condition arises, we take an interrupt.
1134 * At some point while servicing the interrupt, we read bytes from
1135 * the ring buffer and re-arm the rx_timer. However the rx_timer is
1136 * not started until the first byte is received *after* it is armed,
1137 * and any bytes pending in the rx construction buffers are not drained
1138 * to memory until either there are 4 bytes available or the rx_timer
1139 * expires. This leads to a potential situation where data is left
1140 * in the construction buffers forever - 1 to 3 bytes were received
1141 * after the interrupt was generated but before the rx_timer was
1142 * re-armed. At that point as long as no subsequent bytes are received
1143 * the timer will never be started and the bytes will remain in the
1144 * construction buffer forever. The solution is to execute a DRAIN
1145 * command after rearming the timer. This way any bytes received before
1146 * the DRAIN will be drained to memory, and any bytes received after
1147 * the DRAIN will start the TIMER and be drained when it expires.
1148 * Luckily, this only needs to be done when the DMA buffer is empty
1149 * since there is no requirement that this function return all
1150 * available data as long as it returns some.
1151 */
1152 /* Re-arm the timer */
1153
1154 writel(port->ip_rx_cons | SRCIR_ARM, &port->ip_serial_regs->srcir);
1155
1156 prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
1157 cons_ptr = port->ip_rx_cons;
1158
1159 if (prod_ptr == cons_ptr) {
1160 int reset_dma = 0;
1161
1162 /* Input buffer appears empty, do a flush. */
1163
1164 /* DMA must be enabled for this to work. */
1165 if (!(port->ip_sscr & SSCR_DMA_EN)) {
1166 port->ip_sscr |= SSCR_DMA_EN;
1167 reset_dma = 1;
1168 }
1169
1170 /* Potential race condition: we must reload the srpir after
1171 * issuing the drain command, otherwise we could think the rx
1172 * buffer is empty, then take a very long interrupt, and when
1173 * we come back it's full and we wait forever for the drain to
1174 * complete.
1175 */
1176 writel(port->ip_sscr | SSCR_RX_DRAIN,
1177 &port->ip_serial_regs->sscr);
1178 prod_ptr = readl(&port->ip_serial_regs->srpir) & PROD_CONS_MASK;
1179
1180 /* We must not wait for the DRAIN to complete unless there are
1181 * at least 8 bytes (2 ring entries) available to receive the
1182 * data otherwise the DRAIN will never complete and we'll
1183 * deadlock here.
1184 * In fact, to make things easier, I'll just ignore the flush if
1185 * there is any data at all now available.
1186 */
1187 if (prod_ptr == cons_ptr) {
1188 loop_counter = 0;
1189 while (readl(&port->ip_serial_regs->sscr) &
1190 SSCR_RX_DRAIN) {
1191 loop_counter++;
1192 if (loop_counter > MAXITER)
1193 return -1;
1194 }
1195
1196 /* SIGH. We have to reload the prod_ptr *again* since
1197 * the drain may have caused it to change
1198 */
1199 prod_ptr = readl(&port->ip_serial_regs->srpir)
1200 & PROD_CONS_MASK;
1201 }
1202 if (reset_dma) {
1203 port->ip_sscr &= ~SSCR_DMA_EN;
1204 writel(port->ip_sscr, &port->ip_serial_regs->sscr);
1205 }
1206 }
1207 inring = port->ip_inring;
1208 port->ip_flags &= ~READ_ABORTED;
1209
1210 total = 0;
1211 loop_counter = 0xfffff; /* to avoid hangs */
1212
1213 /* Grab bytes from the hardware */
1214 while ((prod_ptr != cons_ptr) && (len > 0)) {
1215 entry = (struct ring_entry *)((caddr_t) inring + cons_ptr);
1216
1217 if (loop_counter-- <= 0) {
1218 printk(KERN_WARNING "IOC3 serial: "
1219 "possible hang condition/"
1220 "port stuck on read (line %d).\n",
1221 the_port->line);
1222 break;
1223 }
1224
1225 /* According to the producer pointer, this ring entry
1226 * must contain some data. But if the PIO happened faster
1227 * than the DMA, the data may not be available yet, so let's
1228 * wait until it arrives.
1229 */
1230 if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
1231 /* Indicate the read is aborted so we don't disable
1232 * the interrupt thinking that the consumer is
1233 * congested.
1234 */
1235 port->ip_flags |= READ_ABORTED;
1236 len = 0;
1237 break;
1238 }
1239
1240 /* Load the bytes/status out of the ring entry */
1241 for (byte_num = 0; byte_num < 4 && len > 0; byte_num++) {
1242 sc = &(entry->ring_sc[byte_num]);
1243
1244 /* Check for change in modem state or overrun */
1245 if ((*sc & RXSB_MODEM_VALID)
1246 && (port->ip_notify & N_DDCD)) {
1247 /* Notify upper layer if DCD dropped */
1248 if ((port->ip_flags & DCD_ON)
1249 && !(*sc & RXSB_DCD)) {
1250 /* If we have already copied some data,
1251 * return it. We'll pick up the carrier
1252 * drop on the next pass. That way we
1253 * don't throw away the data that has
1254 * already been copied back to
1255 * the caller's buffer.
1256 */
1257 if (total > 0) {
1258 len = 0;
1259 break;
1260 }
1261 port->ip_flags &= ~DCD_ON;
1262
1263 /* Turn off this notification so the
1264 * carrier drop protocol won't see it
1265 * again when it does a read.
1266 */
1267 *sc &= ~RXSB_MODEM_VALID;
1268
1269 /* To keep things consistent, we need
1270 * to update the consumer pointer so
1271 * the next reader won't come in and
1272 * try to read the same ring entries
1273 * again. This must be done here before
1274 * the dcd change.
1275 */
1276
1277 if ((entry->ring_allsc & RING_ANY_VALID)
1278 == 0) {
1279 cons_ptr += (int)sizeof
1280 (struct ring_entry);
1281 cons_ptr &= PROD_CONS_MASK;
1282 }
1283 writel(cons_ptr,
1284 &port->ip_serial_regs->srcir);
1285 port->ip_rx_cons = cons_ptr;
1286
1287 /* Notify upper layer of carrier drop */
1288 if ((port->ip_notify & N_DDCD)
1289 && port->ip_port) {
1290 uart_handle_dcd_change
1291 (port->ip_port, 0);
1292 wake_up_interruptible
Alan Coxebd2c8f2009-09-19 13:13:28 -07001293 (&the_port->state->
Alan Coxbdc04e32009-09-19 13:13:31 -07001294 port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001295 }
1296
1297 /* If we had any data to return, we
1298 * would have returned it above.
1299 */
1300 return 0;
1301 }
1302 }
1303 if (*sc & RXSB_MODEM_VALID) {
1304 /* Notify that an input overrun occurred */
1305 if ((*sc & RXSB_OVERRUN)
1306 && (port->ip_notify & N_OVERRUN_ERROR)) {
1307 ioc3_cb_post_ncs(the_port, NCS_OVERRUN);
1308 }
1309 /* Don't look at this byte again */
1310 *sc &= ~RXSB_MODEM_VALID;
1311 }
1312
1313 /* Check for valid data or RX errors */
1314 if ((*sc & RXSB_DATA_VALID) &&
1315 ((*sc & (RXSB_PAR_ERR
1316 | RXSB_FRAME_ERR | RXSB_BREAK))
1317 && (port->ip_notify & (N_PARITY_ERROR
1318 | N_FRAMING_ERROR
1319 | N_BREAK)))) {
1320 /* There is an error condition on the next byte.
1321 * If we have already transferred some bytes,
1322 * we'll stop here. Otherwise if this is the
1323 * first byte to be read, we'll just transfer
1324 * it alone after notifying the
1325 * upper layer of its status.
1326 */
1327 if (total > 0) {
1328 len = 0;
1329 break;
1330 } else {
1331 if ((*sc & RXSB_PAR_ERR) &&
1332 (port->
1333 ip_notify & N_PARITY_ERROR)) {
1334 ioc3_cb_post_ncs(the_port,
1335 NCS_PARITY);
1336 }
1337 if ((*sc & RXSB_FRAME_ERR) &&
1338 (port->
1339 ip_notify & N_FRAMING_ERROR)) {
1340 ioc3_cb_post_ncs(the_port,
1341 NCS_FRAMING);
1342 }
1343 if ((*sc & RXSB_BREAK)
1344 && (port->ip_notify & N_BREAK)) {
1345 ioc3_cb_post_ncs
1346 (the_port, NCS_BREAK);
1347 }
1348 len = 1;
1349 }
1350 }
1351 if (*sc & RXSB_DATA_VALID) {
1352 *sc &= ~RXSB_DATA_VALID;
1353 *buf = entry->ring_data[byte_num];
1354 buf++;
1355 len--;
1356 total++;
1357 }
1358 }
1359
1360 /* If we used up this entry entirely, go on to the next one,
1361 * otherwise we must have run out of buffer space, so
1362 * leave the consumer pointer here for the next read in case
1363 * there are still unread bytes in this entry.
1364 */
1365 if ((entry->ring_allsc & RING_ANY_VALID) == 0) {
1366 cons_ptr += (int)sizeof(struct ring_entry);
1367 cons_ptr &= PROD_CONS_MASK;
1368 }
1369 }
1370
1371 /* Update consumer pointer and re-arm rx timer interrupt */
1372 writel(cons_ptr, &port->ip_serial_regs->srcir);
1373 port->ip_rx_cons = cons_ptr;
1374
1375 /* If we have now dipped below the rx high water mark and we have
1376 * rx_high interrupt turned off, we can now turn it back on again.
1377 */
1378 if ((port->ip_flags & INPUT_HIGH) && (((prod_ptr - cons_ptr)
1379 & PROD_CONS_MASK) <
1380 ((port->
1381 ip_sscr &
1382 SSCR_RX_THRESHOLD)
1383 << PROD_CONS_PTR_OFF))) {
1384 port->ip_flags &= ~INPUT_HIGH;
1385 enable_intrs(port, hooks->intr_rx_high);
1386 }
1387 return total;
1388}
1389
1390/**
1391 * receive_chars - upper level read.
1392 * @the_port: port to read from
1393 */
1394static int receive_chars(struct uart_port *the_port)
1395{
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001396 unsigned char ch[MAX_CHARS];
1397 int read_count = 0, read_room, flip = 0;
Alan Coxebd2c8f2009-09-19 13:13:28 -07001398 struct uart_state *state = the_port->state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001399 struct ioc3_port *port = get_ioc3_port(the_port);
1400 unsigned long pflags;
1401
1402 /* Make sure all the pointers are "good" ones */
Alan Coxebd2c8f2009-09-19 13:13:28 -07001403 if (!state)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001404 return 0;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001405
1406 if (!(port->ip_flags & INPUT_ENABLE))
1407 return 0;
1408
1409 spin_lock_irqsave(&the_port->lock, pflags);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001410
1411 read_count = do_read(the_port, ch, MAX_CHARS);
1412 if (read_count > 0) {
1413 flip = 1;
Jiri Slaby05c7cd32013-01-03 15:53:04 +01001414 read_room = tty_insert_flip_string(&state->port, ch,
1415 read_count);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001416 the_port->icount.rx += read_count;
1417 }
1418 spin_unlock_irqrestore(&the_port->lock, pflags);
1419
1420 if (flip)
Jiri Slaby2e124b42013-01-03 15:53:06 +01001421 tty_flip_buffer_push(&state->port);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001422
1423 return read_count;
1424}
1425
1426/**
1427 * ioc3uart_intr_one - lowest level (per port) interrupt handler.
1428 * @is : submodule
1429 * @idd: driver data
1430 * @pending: interrupts to handle
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001431 */
1432
1433static int inline
1434ioc3uart_intr_one(struct ioc3_submodule *is,
1435 struct ioc3_driver_data *idd,
David Howells7d12e782006-10-05 14:55:46 +01001436 unsigned int pending)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001437{
1438 int port_num = GET_PORT_FROM_SIO_IR(pending);
1439 struct port_hooks *hooks;
1440 unsigned int rx_high_rd_aborted = 0;
1441 unsigned long flags;
1442 struct uart_port *the_port;
1443 struct ioc3_port *port;
1444 int loop_counter;
1445 struct ioc3_card *card_ptr;
1446 unsigned int sio_ir;
1447
1448 card_ptr = idd->data[is->id];
1449 port = card_ptr->ic_port[port_num].icp_port;
1450 hooks = port->ip_hooks;
1451
1452 /* Possible race condition here: The tx_mt interrupt bit may be
1453 * cleared without the intervention of the interrupt handler,
1454 * e.g. by a write. If the top level interrupt handler reads a
1455 * tx_mt, then some other processor does a write, starting up
1456 * output, then we come in here, see the tx_mt and stop DMA, the
1457 * output started by the other processor will hang. Thus we can
1458 * only rely on tx_mt being legitimate if it is read while the
1459 * port lock is held. Therefore this bit must be ignored in the
1460 * passed in interrupt mask which was read by the top level
1461 * interrupt handler since the port lock was not held at the time
1462 * it was read. We can only rely on this bit being accurate if it
1463 * is read while the port lock is held. So we'll clear it for now,
1464 * and reload it later once we have the port lock.
1465 */
1466
1467 sio_ir = pending & ~(hooks->intr_tx_mt);
1468 spin_lock_irqsave(&port->ip_lock, flags);
1469
1470 loop_counter = MAXITER; /* to avoid hangs */
1471
1472 do {
1473 uint32_t shadow;
1474
1475 if (loop_counter-- <= 0) {
1476 printk(KERN_WARNING "IOC3 serial: "
1477 "possible hang condition/"
1478 "port stuck on interrupt (line %d).\n",
1479 ((struct uart_port *)port->ip_port)->line);
1480 break;
1481 }
1482 /* Handle a DCD change */
1483 if (sio_ir & hooks->intr_delta_dcd) {
1484 ioc3_ack(is, idd, hooks->intr_delta_dcd);
1485 shadow = readl(&port->ip_serial_regs->shadow);
1486
1487 if ((port->ip_notify & N_DDCD)
1488 && (shadow & SHADOW_DCD)
1489 && (port->ip_port)) {
1490 the_port = port->ip_port;
1491 uart_handle_dcd_change(the_port,
1492 shadow & SHADOW_DCD);
1493 wake_up_interruptible
Alan Coxbdc04e32009-09-19 13:13:31 -07001494 (&the_port->state->port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001495 } else if ((port->ip_notify & N_DDCD)
1496 && !(shadow & SHADOW_DCD)) {
1497 /* Flag delta DCD/no DCD */
1498 uart_handle_dcd_change(port->ip_port,
1499 shadow & SHADOW_DCD);
1500 port->ip_flags |= DCD_ON;
1501 }
1502 }
1503
1504 /* Handle a CTS change */
1505 if (sio_ir & hooks->intr_delta_cts) {
1506 ioc3_ack(is, idd, hooks->intr_delta_cts);
1507 shadow = readl(&port->ip_serial_regs->shadow);
1508
1509 if ((port->ip_notify & N_DCTS) && (port->ip_port)) {
1510 the_port = port->ip_port;
1511 uart_handle_cts_change(the_port, shadow
1512 & SHADOW_CTS);
1513 wake_up_interruptible
Alan Coxbdc04e32009-09-19 13:13:31 -07001514 (&the_port->state->port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001515 }
1516 }
1517
1518 /* rx timeout interrupt. Must be some data available. Put this
1519 * before the check for rx_high since servicing this condition
1520 * may cause that condition to clear.
1521 */
1522 if (sio_ir & hooks->intr_rx_timer) {
1523 ioc3_ack(is, idd, hooks->intr_rx_timer);
1524 if ((port->ip_notify & N_DATA_READY)
1525 && (port->ip_port)) {
1526 receive_chars(port->ip_port);
1527 }
1528 }
1529
1530 /* rx high interrupt. Must be after rx_timer. */
1531 else if (sio_ir & hooks->intr_rx_high) {
1532 /* Data available, notify upper layer */
1533 if ((port->ip_notify & N_DATA_READY) && port->ip_port) {
1534 receive_chars(port->ip_port);
1535 }
1536
1537 /* We can't ACK this interrupt. If receive_chars didn't
1538 * cause the condition to clear, we'll have to disable
1539 * the interrupt until the data is drained.
1540 * If the read was aborted, don't disable the interrupt
1541 * as this may cause us to hang indefinitely. An
1542 * aborted read generally means that this interrupt
1543 * hasn't been delivered to the cpu yet anyway, even
1544 * though we see it as asserted when we read the sio_ir.
1545 */
1546 if ((sio_ir = PENDING(card_ptr, idd))
1547 & hooks->intr_rx_high) {
1548 if (port->ip_flags & READ_ABORTED) {
1549 rx_high_rd_aborted++;
1550 }
1551 else {
1552 card_ptr->ic_enable &= ~hooks->intr_rx_high;
1553 port->ip_flags |= INPUT_HIGH;
1554 }
1555 }
1556 }
1557
1558 /* We got a low water interrupt: notify upper layer to
1559 * send more data. Must come before tx_mt since servicing
1560 * this condition may cause that condition to clear.
1561 */
1562 if (sio_ir & hooks->intr_tx_explicit) {
1563 port->ip_flags &= ~LOWAT_WRITTEN;
1564 ioc3_ack(is, idd, hooks->intr_tx_explicit);
1565 if (port->ip_notify & N_OUTPUT_LOWAT)
1566 ioc3_cb_output_lowat(port);
1567 }
1568
1569 /* Handle tx_mt. Must come after tx_explicit. */
1570 else if (sio_ir & hooks->intr_tx_mt) {
1571 /* If we are expecting a lowat notification
1572 * and we get to this point it probably means that for
1573 * some reason the tx_explicit didn't work as expected
1574 * (that can legitimately happen if the output buffer is
1575 * filled up in just the right way).
1576 * So send the notification now.
1577 */
1578 if (port->ip_notify & N_OUTPUT_LOWAT) {
1579 ioc3_cb_output_lowat(port);
1580
1581 /* We need to reload the sio_ir since the lowat
1582 * call may have caused another write to occur,
1583 * clearing the tx_mt condition.
1584 */
1585 sio_ir = PENDING(card_ptr, idd);
1586 }
1587
1588 /* If the tx_mt condition still persists even after the
1589 * lowat call, we've got some work to do.
1590 */
1591 if (sio_ir & hooks->intr_tx_mt) {
1592 /* If we are not currently expecting DMA input,
1593 * and the transmitter has just gone idle,
1594 * there is no longer any reason for DMA, so
1595 * disable it.
1596 */
1597 if (!(port->ip_notify
1598 & (N_DATA_READY | N_DDCD))) {
1599 BUG_ON(!(port->ip_sscr
1600 & SSCR_DMA_EN));
1601 port->ip_sscr &= ~SSCR_DMA_EN;
1602 writel(port->ip_sscr,
1603 &port->ip_serial_regs->sscr);
1604 }
1605 /* Prevent infinite tx_mt interrupt */
1606 card_ptr->ic_enable &= ~hooks->intr_tx_mt;
1607 }
1608 }
1609 sio_ir = PENDING(card_ptr, idd);
1610
1611 /* if the read was aborted and only hooks->intr_rx_high,
1612 * clear hooks->intr_rx_high, so we do not loop forever.
1613 */
1614
1615 if (rx_high_rd_aborted && (sio_ir == hooks->intr_rx_high)) {
1616 sio_ir &= ~hooks->intr_rx_high;
1617 }
1618 } while (sio_ir & hooks->intr_all);
1619
1620 spin_unlock_irqrestore(&port->ip_lock, flags);
1621 ioc3_enable(is, idd, card_ptr->ic_enable);
1622 return 0;
1623}
1624
1625/**
1626 * ioc3uart_intr - field all serial interrupts
1627 * @is : submodule
1628 * @idd: driver data
1629 * @pending: interrupts to handle
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001630 *
1631 */
1632
1633static int ioc3uart_intr(struct ioc3_submodule *is,
1634 struct ioc3_driver_data *idd,
David Howells7d12e782006-10-05 14:55:46 +01001635 unsigned int pending)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001636{
1637 int ret = 0;
1638
1639 /*
1640 * The upper level interrupt handler sends interrupts for both ports
1641 * here. So we need to call for each port with its interrupts.
1642 */
1643
1644 if (pending & SIO_IR_SA)
David Howells7d12e782006-10-05 14:55:46 +01001645 ret |= ioc3uart_intr_one(is, idd, pending & SIO_IR_SA);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001646 if (pending & SIO_IR_SB)
David Howells7d12e782006-10-05 14:55:46 +01001647 ret |= ioc3uart_intr_one(is, idd, pending & SIO_IR_SB);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001648
1649 return ret;
1650}
1651
1652/**
1653 * ic3_type
1654 * @port: Port to operate with (we ignore since we only have one port)
1655 *
1656 */
1657static const char *ic3_type(struct uart_port *the_port)
1658{
1659 if (IS_RS232(the_port->line))
1660 return "SGI IOC3 Serial [rs232]";
1661 else
1662 return "SGI IOC3 Serial [rs422]";
1663}
1664
1665/**
1666 * ic3_tx_empty - Is the transmitter empty?
1667 * @port: Port to operate on
1668 *
1669 */
1670static unsigned int ic3_tx_empty(struct uart_port *the_port)
1671{
1672 unsigned int ret = 0;
1673 struct ioc3_port *port = get_ioc3_port(the_port);
1674
1675 if (readl(&port->ip_serial_regs->shadow) & SHADOW_TEMT)
1676 ret = TIOCSER_TEMT;
1677 return ret;
1678}
1679
1680/**
1681 * ic3_stop_tx - stop the transmitter
1682 * @port: Port to operate on
1683 *
1684 */
1685static void ic3_stop_tx(struct uart_port *the_port)
1686{
1687 struct ioc3_port *port = get_ioc3_port(the_port);
1688
1689 if (port)
1690 set_notification(port, N_OUTPUT_LOWAT, 0);
1691}
1692
1693/**
1694 * ic3_stop_rx - stop the receiver
1695 * @port: Port to operate on
1696 *
1697 */
1698static void ic3_stop_rx(struct uart_port *the_port)
1699{
1700 struct ioc3_port *port = get_ioc3_port(the_port);
1701
1702 if (port)
1703 port->ip_flags &= ~INPUT_ENABLE;
1704}
1705
1706/**
1707 * null_void_function
1708 * @port: Port to operate on
1709 *
1710 */
1711static void null_void_function(struct uart_port *the_port)
1712{
1713}
1714
1715/**
1716 * ic3_shutdown - shut down the port - free irq and disable
1717 * @port: port to shut down
1718 *
1719 */
1720static void ic3_shutdown(struct uart_port *the_port)
1721{
1722 unsigned long port_flags;
1723 struct ioc3_port *port;
Alan Coxebd2c8f2009-09-19 13:13:28 -07001724 struct uart_state *state;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001725
1726 port = get_ioc3_port(the_port);
1727 if (!port)
1728 return;
1729
Alan Coxebd2c8f2009-09-19 13:13:28 -07001730 state = the_port->state;
Alan Coxbdc04e32009-09-19 13:13:31 -07001731 wake_up_interruptible(&state->port.delta_msr_wait);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001732
1733 spin_lock_irqsave(&the_port->lock, port_flags);
1734 set_notification(port, N_ALL, 0);
1735 spin_unlock_irqrestore(&the_port->lock, port_flags);
1736}
1737
1738/**
1739 * ic3_set_mctrl - set control lines (dtr, rts, etc)
1740 * @port: Port to operate on
1741 * @mctrl: Lines to set/unset
1742 *
1743 */
1744static void ic3_set_mctrl(struct uart_port *the_port, unsigned int mctrl)
1745{
1746 unsigned char mcr = 0;
1747
1748 if (mctrl & TIOCM_RTS)
1749 mcr |= UART_MCR_RTS;
1750 if (mctrl & TIOCM_DTR)
1751 mcr |= UART_MCR_DTR;
1752 if (mctrl & TIOCM_OUT1)
1753 mcr |= UART_MCR_OUT1;
1754 if (mctrl & TIOCM_OUT2)
1755 mcr |= UART_MCR_OUT2;
1756 if (mctrl & TIOCM_LOOP)
1757 mcr |= UART_MCR_LOOP;
1758
1759 set_mcr(the_port, mcr, SHADOW_DTR);
1760}
1761
1762/**
1763 * ic3_get_mctrl - get control line info
1764 * @port: port to operate on
1765 *
1766 */
1767static unsigned int ic3_get_mctrl(struct uart_port *the_port)
1768{
1769 struct ioc3_port *port = get_ioc3_port(the_port);
1770 uint32_t shadow;
1771 unsigned int ret = 0;
1772
1773 if (!port)
1774 return 0;
1775
1776 shadow = readl(&port->ip_serial_regs->shadow);
1777 if (shadow & SHADOW_DCD)
1778 ret |= TIOCM_CD;
1779 if (shadow & SHADOW_DR)
1780 ret |= TIOCM_DSR;
1781 if (shadow & SHADOW_CTS)
1782 ret |= TIOCM_CTS;
1783 return ret;
1784}
1785
1786/**
1787 * ic3_start_tx - Start transmitter. Called with the_port->lock
1788 * @port: Port to operate on
1789 *
1790 */
1791static void ic3_start_tx(struct uart_port *the_port)
1792{
1793 struct ioc3_port *port = get_ioc3_port(the_port);
1794
1795 if (port) {
1796 set_notification(port, N_OUTPUT_LOWAT, 1);
1797 enable_intrs(port, port->ip_hooks->intr_tx_mt);
1798 }
1799}
1800
1801/**
1802 * ic3_break_ctl - handle breaks
1803 * @port: Port to operate on
1804 * @break_state: Break state
1805 *
1806 */
1807static void ic3_break_ctl(struct uart_port *the_port, int break_state)
1808{
1809}
1810
1811/**
1812 * ic3_startup - Start up the serial port - always return 0 (We're always on)
1813 * @port: Port to operate on
1814 *
1815 */
1816static int ic3_startup(struct uart_port *the_port)
1817{
1818 int retval;
1819 struct ioc3_port *port;
1820 struct ioc3_card *card_ptr;
1821 unsigned long port_flags;
1822
1823 if (!the_port) {
1824 NOT_PROGRESS();
1825 return -ENODEV;
1826 }
1827 port = get_ioc3_port(the_port);
1828 if (!port) {
1829 NOT_PROGRESS();
1830 return -ENODEV;
1831 }
1832 card_ptr = port->ip_card;
1833 port->ip_port = the_port;
1834
1835 if (!card_ptr) {
1836 NOT_PROGRESS();
1837 return -ENODEV;
1838 }
1839
1840 /* Start up the serial port */
1841 spin_lock_irqsave(&the_port->lock, port_flags);
1842 retval = ic3_startup_local(the_port);
1843 spin_unlock_irqrestore(&the_port->lock, port_flags);
1844 return retval;
1845}
1846
1847/**
1848 * ic3_set_termios - set termios stuff
1849 * @port: port to operate on
1850 * @termios: New settings
1851 * @termios: Old
1852 *
1853 */
1854static void
1855ic3_set_termios(struct uart_port *the_port,
Alan Cox606d0992006-12-08 02:38:45 -08001856 struct ktermios *termios, struct ktermios *old_termios)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001857{
1858 unsigned long port_flags;
1859
1860 spin_lock_irqsave(&the_port->lock, port_flags);
1861 ioc3_change_speed(the_port, termios, old_termios);
1862 spin_unlock_irqrestore(&the_port->lock, port_flags);
1863}
1864
1865/**
1866 * ic3_request_port - allocate resources for port - no op....
1867 * @port: port to operate on
1868 *
1869 */
1870static int ic3_request_port(struct uart_port *port)
1871{
1872 return 0;
1873}
1874
1875/* Associate the uart functions above - given to serial core */
1876static struct uart_ops ioc3_ops = {
1877 .tx_empty = ic3_tx_empty,
1878 .set_mctrl = ic3_set_mctrl,
1879 .get_mctrl = ic3_get_mctrl,
1880 .stop_tx = ic3_stop_tx,
1881 .start_tx = ic3_start_tx,
1882 .stop_rx = ic3_stop_rx,
1883 .enable_ms = null_void_function,
1884 .break_ctl = ic3_break_ctl,
1885 .startup = ic3_startup,
1886 .shutdown = ic3_shutdown,
1887 .set_termios = ic3_set_termios,
1888 .type = ic3_type,
1889 .release_port = null_void_function,
1890 .request_port = ic3_request_port,
1891};
1892
1893/*
1894 * Boot-time initialization code
1895 */
1896
1897static struct uart_driver ioc3_uart = {
1898 .owner = THIS_MODULE,
1899 .driver_name = "ioc3_serial",
1900 .dev_name = DEVICE_NAME,
1901 .major = DEVICE_MAJOR,
1902 .minor = DEVICE_MINOR,
1903 .nr = MAX_LOGICAL_PORTS
1904};
1905
1906/**
1907 * ioc3_serial_core_attach - register with serial core
1908 * This is done during pci probing
1909 * @is: submodule struct for this
1910 * @idd: handle for this card
1911 */
1912static inline int ioc3_serial_core_attach( struct ioc3_submodule *is,
1913 struct ioc3_driver_data *idd)
1914{
1915 struct ioc3_port *port;
1916 struct uart_port *the_port;
1917 struct ioc3_card *card_ptr = idd->data[is->id];
1918 int ii, phys_port;
1919 struct pci_dev *pdev = idd->pdev;
1920
1921 DPRINT_CONFIG(("%s: attach pdev 0x%p - card_ptr 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001922 __func__, pdev, (void *)card_ptr));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001923
1924 if (!card_ptr)
1925 return -ENODEV;
1926
1927 /* once around for each logical port on this card */
1928 for (ii = 0; ii < LOGICAL_PORTS_PER_CARD; ii++) {
1929 phys_port = GET_PHYSICAL_PORT(ii);
1930 the_port = &card_ptr->ic_port[phys_port].
1931 icp_uart_port[GET_LOGICAL_PORT(ii)];
1932 port = card_ptr->ic_port[phys_port].icp_port;
1933 port->ip_port = the_port;
1934
1935 DPRINT_CONFIG(("%s: attach the_port 0x%p / port 0x%p [%d/%d]\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001936 __func__, (void *)the_port, (void *)port,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001937 phys_port, ii));
1938
1939 /* membase, iobase and mapbase just need to be non-0 */
1940 the_port->membase = (unsigned char __iomem *)1;
1941 the_port->iobase = (pdev->bus->number << 16) | ii;
1942 the_port->line = (Num_of_ioc3_cards << 2) | ii;
1943 the_port->mapbase = 1;
1944 the_port->type = PORT_16550A;
1945 the_port->fifosize = FIFO_SIZE;
1946 the_port->ops = &ioc3_ops;
1947 the_port->irq = idd->irq_io;
1948 the_port->dev = &pdev->dev;
1949
1950 if (uart_add_one_port(&ioc3_uart, the_port) < 0) {
1951 printk(KERN_WARNING
1952 "%s: unable to add port %d bus %d\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07001953 __func__, the_port->line, pdev->bus->number);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08001954 } else {
1955 DPRINT_CONFIG(("IOC3 serial port %d irq %d bus %d\n",
1956 the_port->line, the_port->irq, pdev->bus->number));
1957 }
1958
1959 /* all ports are rs232 for now */
1960 if (IS_PHYSICAL_PORT(ii))
1961 ioc3_set_proto(port, PROTO_RS232);
1962 }
1963 return 0;
1964}
1965
1966/**
1967 * ioc3uart_remove - register detach function
1968 * @is: submodule struct for this submodule
1969 * @idd: ioc3 driver data for this submodule
1970 */
1971
1972static int ioc3uart_remove(struct ioc3_submodule *is,
1973 struct ioc3_driver_data *idd)
1974{
1975 struct ioc3_card *card_ptr = idd->data[is->id];
1976 struct uart_port *the_port;
1977 struct ioc3_port *port;
1978 int ii;
1979
1980 if (card_ptr) {
1981 for (ii = 0; ii < LOGICAL_PORTS_PER_CARD; ii++) {
1982 the_port = &card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].
1983 icp_uart_port[GET_LOGICAL_PORT(ii)];
1984 if (the_port)
1985 uart_remove_one_port(&ioc3_uart, the_port);
1986 port = card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].icp_port;
1987 if (port && IS_PHYSICAL_PORT(ii)
1988 && (GET_PHYSICAL_PORT(ii) == 0)) {
1989 pci_free_consistent(port->ip_idd->pdev,
1990 TOTAL_RING_BUF_SIZE,
1991 (void *)port->ip_cpu_ringbuf,
1992 port->ip_dma_ringbuf);
1993 kfree(port);
1994 card_ptr->ic_port[GET_PHYSICAL_PORT(ii)].
1995 icp_port = NULL;
1996 }
1997 }
1998 kfree(card_ptr);
1999 idd->data[is->id] = NULL;
2000 }
2001 return 0;
2002}
2003
2004/**
2005 * ioc3uart_probe - card probe function called from shim driver
2006 * @is: submodule struct for this submodule
2007 * @idd: ioc3 driver data for this card
2008 */
2009
Bill Pemberton9671f092012-11-19 13:21:50 -05002010static int
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002011ioc3uart_probe(struct ioc3_submodule *is, struct ioc3_driver_data *idd)
2012{
2013 struct pci_dev *pdev = idd->pdev;
2014 struct ioc3_card *card_ptr;
2015 int ret = 0;
2016 struct ioc3_port *port;
2017 struct ioc3_port *ports[PORTS_PER_CARD];
2018 int phys_port;
Rahul Ruikar35ed1672010-10-01 13:32:45 -07002019 int cnt;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002020
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002021 DPRINT_CONFIG(("%s (0x%p, 0x%p)\n", __func__, is, idd));
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002022
Burman Yan8f31bb32007-02-14 00:33:07 -08002023 card_ptr = kzalloc(sizeof(struct ioc3_card), GFP_KERNEL);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002024 if (!card_ptr) {
2025 printk(KERN_WARNING "ioc3_attach_one"
2026 ": unable to get memory for the IOC3\n");
2027 return -ENOMEM;
2028 }
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002029 idd->data[is->id] = card_ptr;
2030 Submodule_slot = is->id;
2031
2032 writel(((UARTA_BASE >> 3) << SIO_CR_SER_A_BASE_SHIFT) |
2033 ((UARTB_BASE >> 3) << SIO_CR_SER_B_BASE_SHIFT) |
2034 (0xf << SIO_CR_CMD_PULSE_SHIFT), &idd->vma->sio_cr);
2035
2036 pci_write_config_dword(pdev, PCI_LAT, 0xff00);
2037
2038 /* Enable serial port mode select generic PIO pins as outputs */
2039 ioc3_gpcr_set(idd, GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL);
2040
2041 /* Create port structures for each port */
2042 for (phys_port = 0; phys_port < PORTS_PER_CARD; phys_port++) {
Burman Yan8f31bb32007-02-14 00:33:07 -08002043 port = kzalloc(sizeof(struct ioc3_port), GFP_KERNEL);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002044 if (!port) {
2045 printk(KERN_WARNING
2046 "IOC3 serial memory not available for port\n");
Julia Lawall6cc0cc42010-10-15 15:00:09 +02002047 ret = -ENOMEM;
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002048 goto out4;
2049 }
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002050 spin_lock_init(&port->ip_lock);
2051
2052 /* we need to remember the previous ones, to point back to
2053 * them farther down - setting up the ring buffers.
2054 */
2055 ports[phys_port] = port;
2056
2057 /* init to something useful */
2058 card_ptr->ic_port[phys_port].icp_port = port;
2059 port->ip_is = is;
2060 port->ip_idd = idd;
2061 port->ip_baud = 9600;
2062 port->ip_card = card_ptr;
2063 port->ip_hooks = &hooks_array[phys_port];
2064
2065 /* Setup each port */
2066 if (phys_port == 0) {
2067 port->ip_serial_regs = &idd->vma->port_a;
2068 port->ip_uart_regs = &idd->vma->sregs.uarta;
2069
2070 DPRINT_CONFIG(("%s : Port A ip_serial_regs 0x%p "
2071 "ip_uart_regs 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002072 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002073 (void *)port->ip_serial_regs,
2074 (void *)port->ip_uart_regs));
2075
2076 /* setup ring buffers */
2077 port->ip_cpu_ringbuf = pci_alloc_consistent(pdev,
2078 TOTAL_RING_BUF_SIZE, &port->ip_dma_ringbuf);
2079
2080 BUG_ON(!((((int64_t) port->ip_dma_ringbuf) &
2081 (TOTAL_RING_BUF_SIZE - 1)) == 0));
2082 port->ip_inring = RING(port, RX_A);
2083 port->ip_outring = RING(port, TX_A);
2084 DPRINT_CONFIG(("%s : Port A ip_cpu_ringbuf 0x%p "
2085 "ip_dma_ringbuf 0x%p, ip_inring 0x%p "
2086 "ip_outring 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002087 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002088 (void *)port->ip_cpu_ringbuf,
2089 (void *)port->ip_dma_ringbuf,
2090 (void *)port->ip_inring,
2091 (void *)port->ip_outring));
2092 }
2093 else {
2094 port->ip_serial_regs = &idd->vma->port_b;
2095 port->ip_uart_regs = &idd->vma->sregs.uartb;
2096
2097 DPRINT_CONFIG(("%s : Port B ip_serial_regs 0x%p "
2098 "ip_uart_regs 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002099 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002100 (void *)port->ip_serial_regs,
2101 (void *)port->ip_uart_regs));
2102
2103 /* share the ring buffers */
2104 port->ip_dma_ringbuf =
2105 ports[phys_port - 1]->ip_dma_ringbuf;
2106 port->ip_cpu_ringbuf =
2107 ports[phys_port - 1]->ip_cpu_ringbuf;
2108 port->ip_inring = RING(port, RX_B);
2109 port->ip_outring = RING(port, TX_B);
2110 DPRINT_CONFIG(("%s : Port B ip_cpu_ringbuf 0x%p "
2111 "ip_dma_ringbuf 0x%p, ip_inring 0x%p "
2112 "ip_outring 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002113 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002114 (void *)port->ip_cpu_ringbuf,
2115 (void *)port->ip_dma_ringbuf,
2116 (void *)port->ip_inring,
2117 (void *)port->ip_outring));
2118 }
2119
2120 DPRINT_CONFIG(("%s : port %d [addr 0x%p] card_ptr 0x%p",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002121 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002122 phys_port, (void *)port, (void *)card_ptr));
2123 DPRINT_CONFIG((" ip_serial_regs 0x%p ip_uart_regs 0x%p\n",
2124 (void *)port->ip_serial_regs,
2125 (void *)port->ip_uart_regs));
2126
2127 /* Initialize the hardware for IOC3 */
2128 port_init(port);
2129
2130 DPRINT_CONFIG(("%s: phys_port %d port 0x%p inring 0x%p "
2131 "outring 0x%p\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002132 __func__,
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002133 phys_port, (void *)port,
2134 (void *)port->ip_inring,
2135 (void *)port->ip_outring));
2136
2137 }
2138
2139 /* register port with the serial core */
2140
2141 if ((ret = ioc3_serial_core_attach(is, idd)))
2142 goto out4;
2143
2144 Num_of_ioc3_cards++;
2145
2146 return ret;
2147
2148 /* error exits that give back resources */
2149out4:
Rahul Ruikar35ed1672010-10-01 13:32:45 -07002150 for (cnt = 0; cnt < phys_port; cnt++)
2151 kfree(ports[cnt]);
2152
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002153 kfree(card_ptr);
2154 return ret;
2155}
2156
Tony Luck3c0db892008-12-08 16:16:21 -08002157static struct ioc3_submodule ioc3uart_ops = {
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002158 .name = "IOC3uart",
2159 .probe = ioc3uart_probe,
2160 .remove = ioc3uart_remove,
2161 /* call .intr for both ports initially */
2162 .irq_mask = SIO_IR_SA | SIO_IR_SB,
2163 .intr = ioc3uart_intr,
2164 .owner = THIS_MODULE,
2165};
2166
2167/**
2168 * ioc3_detect - module init called,
2169 */
Jean Delvare2ea5d352009-12-14 18:00:27 -08002170static int __init ioc3uart_init(void)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002171{
2172 int ret;
2173
2174 /* register with serial core */
2175 if ((ret = uart_register_driver(&ioc3_uart)) < 0) {
2176 printk(KERN_WARNING
2177 "%s: Couldn't register IOC3 uart serial driver\n",
Harvey Harrison71cc2c22008-04-30 00:55:10 -07002178 __func__);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002179 return ret;
2180 }
Tony Luck3c0db892008-12-08 16:16:21 -08002181 ret = ioc3_register_submodule(&ioc3uart_ops);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002182 if (ret)
2183 uart_unregister_driver(&ioc3_uart);
2184 return ret;
2185}
2186
Jean Delvare2ea5d352009-12-14 18:00:27 -08002187static void __exit ioc3uart_exit(void)
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002188{
Tony Luck3c0db892008-12-08 16:16:21 -08002189 ioc3_unregister_submodule(&ioc3uart_ops);
Patrick Gefre2d0cfb52006-01-14 13:20:40 -08002190 uart_unregister_driver(&ioc3_uart);
2191}
2192
2193module_init(ioc3uart_init);
2194module_exit(ioc3uart_exit);
2195
2196MODULE_AUTHOR("Pat Gefre - Silicon Graphics Inc. (SGI) <pfg@sgi.com>");
2197MODULE_DESCRIPTION("Serial PCI driver module for SGI IOC3 card");
2198MODULE_LICENSE("GPL");