blob: fd98bb968219f19724b84d19202888b6e564d26d [file] [log] [blame]
Mark Brownfebf1df2008-04-02 00:51:09 -04001
2/*
3 * Register bits and API for Wolfson WM97xx series of codecs
4 */
5
6#ifndef _LINUX_WM97XX_H
7#define _LINUX_WM97XX_H
8
9#include <sound/core.h>
10#include <sound/pcm.h>
11#include <sound/ac97_codec.h>
12#include <sound/initval.h>
13#include <linux/types.h>
14#include <linux/list.h>
15#include <linux/input.h> /* Input device layer */
16#include <linux/platform_device.h>
17
18/*
Marek Vasut99fde512009-07-20 22:28:50 -070019 * WM97xx variants
20 */
21#define WM97xx_GENERIC 0x0000
22#define WM97xx_WM1613 0x1613
23
24/*
Mark Brownfebf1df2008-04-02 00:51:09 -040025 * WM97xx AC97 Touchscreen registers
26 */
27#define AC97_WM97XX_DIGITISER1 0x76
28#define AC97_WM97XX_DIGITISER2 0x78
29#define AC97_WM97XX_DIGITISER_RD 0x7a
30#define AC97_WM9713_DIG1 0x74
31#define AC97_WM9713_DIG2 AC97_WM97XX_DIGITISER1
32#define AC97_WM9713_DIG3 AC97_WM97XX_DIGITISER2
33
34/*
35 * WM97xx register bits
36 */
37#define WM97XX_POLL 0x8000 /* initiate a polling measurement */
38#define WM97XX_ADCSEL_X 0x1000 /* x coord measurement */
39#define WM97XX_ADCSEL_Y 0x2000 /* y coord measurement */
40#define WM97XX_ADCSEL_PRES 0x3000 /* pressure measurement */
Wolfram Sangc8f20522011-07-04 19:22:00 -070041#define WM97XX_AUX_ID1 0x4000
42#define WM97XX_AUX_ID2 0x5000
43#define WM97XX_AUX_ID3 0x6000
44#define WM97XX_AUX_ID4 0x7000
Wolfram Sang24566892011-07-04 19:22:00 -070045#define WM97XX_ADCSEL_MASK 0x7000 /* ADC selection mask */
Mark Brownfebf1df2008-04-02 00:51:09 -040046#define WM97XX_COO 0x0800 /* enable coordinate mode */
47#define WM97XX_CTC 0x0400 /* enable continuous mode */
48#define WM97XX_CM_RATE_93 0x0000 /* 93.75Hz continuous rate */
49#define WM97XX_CM_RATE_187 0x0100 /* 187.5Hz continuous rate */
50#define WM97XX_CM_RATE_375 0x0200 /* 375Hz continuous rate */
51#define WM97XX_CM_RATE_750 0x0300 /* 750Hz continuous rate */
52#define WM97XX_CM_RATE_8K 0x00f0 /* 8kHz continuous rate */
53#define WM97XX_CM_RATE_12K 0x01f0 /* 12kHz continuous rate */
54#define WM97XX_CM_RATE_24K 0x02f0 /* 24kHz continuous rate */
55#define WM97XX_CM_RATE_48K 0x03f0 /* 48kHz continuous rate */
56#define WM97XX_CM_RATE_MASK 0x03f0
57#define WM97XX_RATE(i) (((i & 3) << 8) | ((i & 4) ? 0xf0 : 0))
58#define WM97XX_DELAY(i) ((i << 4) & 0x00f0) /* sample delay times */
59#define WM97XX_DELAY_MASK 0x00f0
60#define WM97XX_SLEN 0x0008 /* slot read back enable */
61#define WM97XX_SLT(i) ((i - 5) & 0x7) /* panel slot (5-11) */
62#define WM97XX_SLT_MASK 0x0007
63#define WM97XX_PRP_DETW 0x4000 /* detect on, digitise off, wake */
64#define WM97XX_PRP_DET 0x8000 /* detect on, digitise off, no wake */
65#define WM97XX_PRP_DET_DIG 0xc000 /* setect on, digitise on */
66#define WM97XX_RPR 0x2000 /* wake up on pen down */
67#define WM97XX_PEN_DOWN 0x8000 /* pen is down */
Mark Brownfebf1df2008-04-02 00:51:09 -040068
Mark Brownfebf1df2008-04-02 00:51:09 -040069/* WM9712 Bits */
70#define WM9712_45W 0x1000 /* set for 5-wire touchscreen */
71#define WM9712_PDEN 0x0800 /* measure only when pen down */
72#define WM9712_WAIT 0x0200 /* wait until adc is read before next sample */
73#define WM9712_PIL 0x0100 /* current used for pressure measurement. set 400uA else 200uA */
74#define WM9712_MASK_HI 0x0040 /* hi on mask pin (47) stops conversions */
75#define WM9712_MASK_EDGE 0x0080 /* rising/falling edge on pin delays sample */
76#define WM9712_MASK_SYNC 0x00c0 /* rising/falling edge on mask initiates sample */
77#define WM9712_RPU(i) (i&0x3f) /* internal pull up on pen detect (64k / rpu) */
78#define WM9712_PD(i) (0x1 << i) /* power management */
79
80/* WM9712 Registers */
81#define AC97_WM9712_POWER 0x24
82#define AC97_WM9712_REV 0x58
83
84/* WM9705 Bits */
85#define WM9705_PDEN 0x1000 /* measure only when pen is down */
86#define WM9705_PINV 0x0800 /* inverts sense of pen down output */
87#define WM9705_BSEN 0x0400 /* BUSY flag enable, pin47 is 1 when busy */
88#define WM9705_BINV 0x0200 /* invert BUSY (pin47) output */
89#define WM9705_WAIT 0x0100 /* wait until adc is read before next sample */
90#define WM9705_PIL 0x0080 /* current used for pressure measurement. set 400uA else 200uA */
91#define WM9705_PHIZ 0x0040 /* set PHONE and PCBEEP inputs to high impedance */
92#define WM9705_MASK_HI 0x0010 /* hi on mask stops conversions */
93#define WM9705_MASK_EDGE 0x0020 /* rising/falling edge on pin delays sample */
94#define WM9705_MASK_SYNC 0x0030 /* rising/falling edge on mask initiates sample */
95#define WM9705_PDD(i) (i & 0x000f) /* pen detect comparator threshold */
96
97
98/* WM9713 Bits */
99#define WM9713_PDPOL 0x0400 /* Pen down polarity */
100#define WM9713_POLL 0x0200 /* initiate a polling measurement */
101#define WM9713_CTC 0x0100 /* enable continuous mode */
102#define WM9713_ADCSEL_X 0x0002 /* X measurement */
103#define WM9713_ADCSEL_Y 0x0004 /* Y measurement */
104#define WM9713_ADCSEL_PRES 0x0008 /* Pressure measurement */
105#define WM9713_COO 0x0001 /* enable coordinate mode */
Mark Brown43f83a82008-05-27 01:37:26 -0400106#define WM9713_45W 0x1000 /* set for 5 wire panel */
Mark Brownfebf1df2008-04-02 00:51:09 -0400107#define WM9713_PDEN 0x0800 /* measure only when pen down */
108#define WM9713_ADCSEL_MASK 0x00fe /* ADC selection mask */
109#define WM9713_WAIT 0x0200 /* coordinate wait */
110
111/* AUX ADC ID's */
112#define TS_COMP1 0x0
113#define TS_COMP2 0x1
114#define TS_BMON 0x2
115#define TS_WIPER 0x3
116
117/* ID numbers */
118#define WM97XX_ID1 0x574d
119#define WM9712_ID2 0x4c12
120#define WM9705_ID2 0x4c05
121#define WM9713_ID2 0x4c13
122
123/* Codec GPIO's */
124#define WM97XX_MAX_GPIO 16
125#define WM97XX_GPIO_1 (1 << 1)
126#define WM97XX_GPIO_2 (1 << 2)
127#define WM97XX_GPIO_3 (1 << 3)
128#define WM97XX_GPIO_4 (1 << 4)
129#define WM97XX_GPIO_5 (1 << 5)
130#define WM97XX_GPIO_6 (1 << 6)
131#define WM97XX_GPIO_7 (1 << 7)
132#define WM97XX_GPIO_8 (1 << 8)
133#define WM97XX_GPIO_9 (1 << 9)
134#define WM97XX_GPIO_10 (1 << 10)
135#define WM97XX_GPIO_11 (1 << 11)
136#define WM97XX_GPIO_12 (1 << 12)
137#define WM97XX_GPIO_13 (1 << 13)
138#define WM97XX_GPIO_14 (1 << 14)
139#define WM97XX_GPIO_15 (1 << 15)
140
141
142#define AC97_LINK_FRAME 21 /* time in uS for AC97 link frame */
143
144
145/*---------------- Return codes from sample reading functions ---------------*/
146
147/* More data is available; call the sample gathering function again */
148#define RC_AGAIN 0x00000001
149/* The returned sample is valid */
150#define RC_VALID 0x00000002
151/* The pen is up (the first RC_VALID without RC_PENUP means pen is down) */
152#define RC_PENUP 0x00000004
153/* The pen is down (RC_VALID implies RC_PENDOWN, but sometimes it is helpful
154 to tell the handler that the pen is down but we don't know yet his coords,
155 so the handler should not sleep or wait for pendown irq) */
156#define RC_PENDOWN 0x00000008
157
158/*
159 * The wm97xx driver provides a private API for writing platform-specific
160 * drivers.
161 */
162
163/* The structure used to return arch specific sampled data into */
164struct wm97xx_data {
165 int x;
166 int y;
167 int p;
168};
169
170/*
171 * Codec GPIO status
172 */
173enum wm97xx_gpio_status {
174 WM97XX_GPIO_HIGH,
175 WM97XX_GPIO_LOW
176};
177
178/*
179 * Codec GPIO direction
180 */
181enum wm97xx_gpio_dir {
182 WM97XX_GPIO_IN,
183 WM97XX_GPIO_OUT
184};
185
186/*
187 * Codec GPIO polarity
188 */
189enum wm97xx_gpio_pol {
190 WM97XX_GPIO_POL_HIGH,
191 WM97XX_GPIO_POL_LOW
192};
193
194/*
195 * Codec GPIO sticky
196 */
197enum wm97xx_gpio_sticky {
198 WM97XX_GPIO_STICKY,
199 WM97XX_GPIO_NOTSTICKY
200};
201
202/*
203 * Codec GPIO wake
204 */
205enum wm97xx_gpio_wake {
206 WM97XX_GPIO_WAKE,
207 WM97XX_GPIO_NOWAKE
208};
209
210/*
211 * Digitiser ioctl commands
212 */
213#define WM97XX_DIG_START 0x1
214#define WM97XX_DIG_STOP 0x2
215#define WM97XX_PHY_INIT 0x3
216#define WM97XX_AUX_PREPARE 0x4
217#define WM97XX_DIG_RESTORE 0x5
218
219struct wm97xx;
220
221extern struct wm97xx_codec_drv wm9705_codec;
222extern struct wm97xx_codec_drv wm9712_codec;
223extern struct wm97xx_codec_drv wm9713_codec;
224
225/*
226 * Codec driver interface - allows mapping to WM9705/12/13 and newer codecs
227 */
228struct wm97xx_codec_drv {
229 u16 id;
230 char *name;
231
232 /* read 1 sample */
233 int (*poll_sample) (struct wm97xx *, int adcsel, int *sample);
234
235 /* read X,Y,[P] in poll */
236 int (*poll_touch) (struct wm97xx *, struct wm97xx_data *);
237
238 int (*acc_enable) (struct wm97xx *, int enable);
239 void (*phy_init) (struct wm97xx *);
240 void (*dig_enable) (struct wm97xx *, int enable);
241 void (*dig_restore) (struct wm97xx *);
242 void (*aux_prepare) (struct wm97xx *);
243};
244
245
246/* Machine specific and accelerated touch operations */
247struct wm97xx_mach_ops {
248
249 /* accelerated touch readback - coords are transmited on AC97 link */
250 int acc_enabled;
251 void (*acc_pen_up) (struct wm97xx *);
252 int (*acc_pen_down) (struct wm97xx *);
253 int (*acc_startup) (struct wm97xx *);
254 void (*acc_shutdown) (struct wm97xx *);
255
256 /* interrupt mask control - required for accelerated operation */
257 void (*irq_enable) (struct wm97xx *, int enable);
258
259 /* GPIO pin used for accelerated operation */
260 int irq_gpio;
261
262 /* pre and post sample - can be used to minimise any analog noise */
263 void (*pre_sample) (int); /* function to run before sampling */
264 void (*post_sample) (int); /* function to run after sampling */
265};
266
267struct wm97xx {
268 u16 dig[3], id, gpio[6], misc; /* Cached codec registers */
269 u16 dig_save[3]; /* saved during aux reading */
270 struct wm97xx_codec_drv *codec; /* attached codec driver*/
271 struct input_dev *input_dev; /* touchscreen input device */
272 struct snd_ac97 *ac97; /* ALSA codec access */
273 struct device *dev; /* ALSA device */
274 struct platform_device *battery_dev;
275 struct platform_device *touch_dev;
276 struct wm97xx_mach_ops *mach_ops;
277 struct mutex codec_mutex;
278 struct delayed_work ts_reader; /* Used to poll touchscreen */
279 unsigned long ts_reader_interval; /* Current interval for timer */
280 unsigned long ts_reader_min_interval; /* Minimum interval */
281 unsigned int pen_irq; /* Pen IRQ number in use */
282 struct workqueue_struct *ts_workq;
283 struct work_struct pen_event_work;
284 u16 acc_slot; /* AC97 slot used for acc touch data */
285 u16 acc_rate; /* acc touch data rate */
286 unsigned pen_is_down:1; /* Pen is down */
287 unsigned aux_waiting:1; /* aux measurement waiting */
288 unsigned pen_probably_down:1; /* used in polling mode */
Marek Vasut99fde512009-07-20 22:28:50 -0700289 u16 variant; /* WM97xx chip variant */
Mark Brown34d27852008-04-17 09:24:58 -0400290 u16 suspend_mode; /* PRP in suspend mode */
Mark Brownfebf1df2008-04-02 00:51:09 -0400291};
292
Marek Vasutb8bdc1d2009-08-31 06:20:12 +0200293struct wm97xx_batt_pdata {
294 int batt_aux;
295 int temp_aux;
296 int charge_gpio;
297 int min_voltage;
298 int max_voltage;
299 int batt_div;
300 int batt_mult;
301 int temp_div;
302 int temp_mult;
303 int batt_tech;
304 char *batt_name;
305};
306
307struct wm97xx_pdata {
308 struct wm97xx_batt_pdata *batt_pdata; /* battery data */
309};
310
Mark Brownfebf1df2008-04-02 00:51:09 -0400311/*
312 * Codec GPIO access (not supported on WM9705)
313 * This can be used to set/get codec GPIO and Virtual GPIO status.
314 */
315enum wm97xx_gpio_status wm97xx_get_gpio(struct wm97xx *wm, u32 gpio);
316void wm97xx_set_gpio(struct wm97xx *wm, u32 gpio,
317 enum wm97xx_gpio_status status);
318void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio,
319 enum wm97xx_gpio_dir dir,
320 enum wm97xx_gpio_pol pol,
321 enum wm97xx_gpio_sticky sticky,
322 enum wm97xx_gpio_wake wake);
323
Mark Brown34d27852008-04-17 09:24:58 -0400324void wm97xx_set_suspend_mode(struct wm97xx *wm, u16 mode);
325
Mark Brownfebf1df2008-04-02 00:51:09 -0400326/* codec AC97 IO access */
327int wm97xx_reg_read(struct wm97xx *wm, u16 reg);
328void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val);
329
330/* aux adc readback */
331int wm97xx_read_aux_adc(struct wm97xx *wm, u16 adcsel);
332
333/* machine ops */
334int wm97xx_register_mach_ops(struct wm97xx *, struct wm97xx_mach_ops *);
335void wm97xx_unregister_mach_ops(struct wm97xx *);
336
337#endif