blob: 35866d5872ad1c82bdc487909cd359a84dabb790 [file] [log] [blame]
Alan Cox7831d562009-04-08 20:13:16 +01001/*
2 *
3 * Copyright (C) 2008 Christian Pellegrin <chripell@evolware.org>
4 *
5 * This program is free software; you can redistribute it and/or modify
6 * it under the terms of the GNU General Public License as published by
7 * the Free Software Foundation; either version 2 of the License, or
8 * (at your option) any later version.
9 *
10 *
11 * Notes: the MAX3100 doesn't provide an interrupt on CTS so we have
12 * to use polling for flow control. TX empty IRQ is unusable, since
13 * writing conf clears FIFO buffer and we cannot have this interrupt
14 * always asking us for attention.
15 *
16 * Example platform data:
17
18 static struct plat_max3100 max3100_plat_data = {
19 .loopback = 0,
20 .crystal = 0,
21 .poll_time = 100,
22 };
23
24 static struct spi_board_info spi_board_info[] = {
25 {
26 .modalias = "max3100",
27 .platform_data = &max3100_plat_data,
28 .irq = IRQ_EINT12,
29 .max_speed_hz = 5*1000*1000,
30 .chip_select = 0,
31 },
32 };
33
34 * The initial minor number is 209 in the low-density serial port:
35 * mknod /dev/ttyMAX0 c 204 209
36 */
37
38#define MAX3100_MAJOR 204
39#define MAX3100_MINOR 209
40/* 4 MAX3100s should be enough for everyone */
41#define MAX_MAX3100 4
42
43#include <linux/delay.h>
Tejun Heo5a0e3ad2010-03-24 17:04:11 +090044#include <linux/slab.h>
Alan Cox7831d562009-04-08 20:13:16 +010045#include <linux/device.h>
Paul Gortmaker578b9ce2011-05-27 16:14:23 -040046#include <linux/module.h>
Alan Cox7831d562009-04-08 20:13:16 +010047#include <linux/serial_core.h>
48#include <linux/serial.h>
49#include <linux/spi/spi.h>
50#include <linux/freezer.h>
Jiri Slabyee160a32011-09-01 16:20:57 +020051#include <linux/tty.h>
52#include <linux/tty_flip.h>
Alan Cox7831d562009-04-08 20:13:16 +010053
54#include <linux/serial_max3100.h>
55
56#define MAX3100_C (1<<14)
57#define MAX3100_D (0<<14)
58#define MAX3100_W (1<<15)
59#define MAX3100_RX (0<<15)
60
61#define MAX3100_WC (MAX3100_W | MAX3100_C)
62#define MAX3100_RC (MAX3100_RX | MAX3100_C)
63#define MAX3100_WD (MAX3100_W | MAX3100_D)
64#define MAX3100_RD (MAX3100_RX | MAX3100_D)
65#define MAX3100_CMD (3 << 14)
66
67#define MAX3100_T (1<<14)
68#define MAX3100_R (1<<15)
69
70#define MAX3100_FEN (1<<13)
71#define MAX3100_SHDN (1<<12)
72#define MAX3100_TM (1<<11)
73#define MAX3100_RM (1<<10)
74#define MAX3100_PM (1<<9)
75#define MAX3100_RAM (1<<8)
76#define MAX3100_IR (1<<7)
77#define MAX3100_ST (1<<6)
78#define MAX3100_PE (1<<5)
79#define MAX3100_L (1<<4)
80#define MAX3100_BAUD (0xf)
81
82#define MAX3100_TE (1<<10)
83#define MAX3100_RAFE (1<<10)
84#define MAX3100_RTS (1<<9)
85#define MAX3100_CTS (1<<9)
86#define MAX3100_PT (1<<8)
87#define MAX3100_DATA (0xff)
88
89#define MAX3100_RT (MAX3100_R | MAX3100_T)
90#define MAX3100_RTC (MAX3100_RT | MAX3100_CTS | MAX3100_RAFE)
91
92/* the following simulate a status reg for ignore_status_mask */
93#define MAX3100_STATUS_PE 1
94#define MAX3100_STATUS_FE 2
95#define MAX3100_STATUS_OE 4
96
97struct max3100_port {
98 struct uart_port port;
99 struct spi_device *spi;
100
101 int cts; /* last CTS received for flow ctrl */
102 int tx_empty; /* last TX empty bit */
103
104 spinlock_t conf_lock; /* shared data */
105 int conf_commit; /* need to make changes */
106 int conf; /* configuration for the MAX31000
107 * (bits 0-7, bits 8-11 are irqs) */
108 int rts_commit; /* need to change rts */
109 int rts; /* rts status */
110 int baud; /* current baud rate */
111
112 int parity; /* keeps track if we should send parity */
113#define MAX3100_PARITY_ON 1
114#define MAX3100_PARITY_ODD 2
115#define MAX3100_7BIT 4
116 int rx_enabled; /* if we should rx chars */
117
118 int irq; /* irq assigned to the max3100 */
119
120 int minor; /* minor number */
121 int crystal; /* 1 if 3.6864Mhz crystal 0 for 1.8432 */
122 int loopback; /* 1 if we are in loopback mode */
123
124 /* for handling irqs: need workqueue since we do spi_sync */
125 struct workqueue_struct *workqueue;
126 struct work_struct work;
127 /* set to 1 to make the workhandler exit as soon as possible */
128 int force_end_work;
129 /* need to know we are suspending to avoid deadlock on workqueue */
130 int suspending;
131
132 /* hook for suspending MAX3100 via dedicated pin */
133 void (*max3100_hw_suspend) (int suspend);
134
135 /* poll time (in ms) for ctrl lines */
136 int poll_time;
137 /* and its timer */
138 struct timer_list timer;
139};
140
141static struct max3100_port *max3100s[MAX_MAX3100]; /* the chips */
142static DEFINE_MUTEX(max3100s_lock); /* race on probe */
143
144static int max3100_do_parity(struct max3100_port *s, u16 c)
145{
146 int parity;
147
148 if (s->parity & MAX3100_PARITY_ODD)
149 parity = 1;
150 else
151 parity = 0;
152
153 if (s->parity & MAX3100_7BIT)
154 c &= 0x7f;
155 else
156 c &= 0xff;
157
158 parity = parity ^ (hweight8(c) & 1);
159 return parity;
160}
161
162static int max3100_check_parity(struct max3100_port *s, u16 c)
163{
164 return max3100_do_parity(s, c) == ((c >> 8) & 1);
165}
166
167static void max3100_calc_parity(struct max3100_port *s, u16 *c)
168{
169 if (s->parity & MAX3100_7BIT)
170 *c &= 0x7f;
171 else
172 *c &= 0xff;
173
174 if (s->parity & MAX3100_PARITY_ON)
175 *c |= max3100_do_parity(s, *c) << 8;
176}
177
178static void max3100_work(struct work_struct *w);
179
180static void max3100_dowork(struct max3100_port *s)
181{
Tejun Heo79980052012-12-21 17:57:11 -0800182 if (!s->force_end_work && !freezing(current) && !s->suspending)
Alan Cox7831d562009-04-08 20:13:16 +0100183 queue_work(s->workqueue, &s->work);
184}
185
186static void max3100_timeout(unsigned long data)
187{
188 struct max3100_port *s = (struct max3100_port *)data;
189
Alan Coxebd2c8f2009-09-19 13:13:28 -0700190 if (s->port.state) {
Alan Cox7831d562009-04-08 20:13:16 +0100191 max3100_dowork(s);
192 mod_timer(&s->timer, jiffies + s->poll_time);
193 }
194}
195
196static int max3100_sr(struct max3100_port *s, u16 tx, u16 *rx)
197{
198 struct spi_message message;
199 u16 etx, erx;
200 int status;
201 struct spi_transfer tran = {
202 .tx_buf = &etx,
203 .rx_buf = &erx,
204 .len = 2,
205 };
206
207 etx = cpu_to_be16(tx);
208 spi_message_init(&message);
209 spi_message_add_tail(&tran, &message);
210 status = spi_sync(s->spi, &message);
211 if (status) {
212 dev_warn(&s->spi->dev, "error while calling spi_sync\n");
213 return -EIO;
214 }
215 *rx = be16_to_cpu(erx);
216 s->tx_empty = (*rx & MAX3100_T) > 0;
217 dev_dbg(&s->spi->dev, "%04x - %04x\n", tx, *rx);
218 return 0;
219}
220
221static int max3100_handlerx(struct max3100_port *s, u16 rx)
222{
223 unsigned int ch, flg, status = 0;
224 int ret = 0, cts;
225
226 if (rx & MAX3100_R && s->rx_enabled) {
227 dev_dbg(&s->spi->dev, "%s\n", __func__);
228 ch = rx & (s->parity & MAX3100_7BIT ? 0x7f : 0xff);
229 if (rx & MAX3100_RAFE) {
230 s->port.icount.frame++;
231 flg = TTY_FRAME;
232 status |= MAX3100_STATUS_FE;
233 } else {
234 if (s->parity & MAX3100_PARITY_ON) {
235 if (max3100_check_parity(s, rx)) {
236 s->port.icount.rx++;
237 flg = TTY_NORMAL;
238 } else {
239 s->port.icount.parity++;
240 flg = TTY_PARITY;
241 status |= MAX3100_STATUS_PE;
242 }
243 } else {
244 s->port.icount.rx++;
245 flg = TTY_NORMAL;
246 }
247 }
248 uart_insert_char(&s->port, status, MAX3100_STATUS_OE, ch, flg);
249 ret = 1;
250 }
251
252 cts = (rx & MAX3100_CTS) > 0;
253 if (s->cts != cts) {
254 s->cts = cts;
255 uart_handle_cts_change(&s->port, cts ? TIOCM_CTS : 0);
256 }
257
258 return ret;
259}
260
261static void max3100_work(struct work_struct *w)
262{
263 struct max3100_port *s = container_of(w, struct max3100_port, work);
264 int rxchars;
265 u16 tx, rx;
266 int conf, cconf, rts, crts;
Alan Coxebd2c8f2009-09-19 13:13:28 -0700267 struct circ_buf *xmit = &s->port.state->xmit;
Alan Cox7831d562009-04-08 20:13:16 +0100268
269 dev_dbg(&s->spi->dev, "%s\n", __func__);
270
271 rxchars = 0;
272 do {
273 spin_lock(&s->conf_lock);
274 conf = s->conf;
275 cconf = s->conf_commit;
276 s->conf_commit = 0;
277 rts = s->rts;
278 crts = s->rts_commit;
279 s->rts_commit = 0;
280 spin_unlock(&s->conf_lock);
281 if (cconf)
282 max3100_sr(s, MAX3100_WC | conf, &rx);
283 if (crts) {
284 max3100_sr(s, MAX3100_WD | MAX3100_TE |
285 (s->rts ? MAX3100_RTS : 0), &rx);
286 rxchars += max3100_handlerx(s, rx);
287 }
288
289 max3100_sr(s, MAX3100_RD, &rx);
290 rxchars += max3100_handlerx(s, rx);
291
292 if (rx & MAX3100_T) {
293 tx = 0xffff;
294 if (s->port.x_char) {
295 tx = s->port.x_char;
296 s->port.icount.tx++;
297 s->port.x_char = 0;
298 } else if (!uart_circ_empty(xmit) &&
299 !uart_tx_stopped(&s->port)) {
300 tx = xmit->buf[xmit->tail];
301 xmit->tail = (xmit->tail + 1) &
302 (UART_XMIT_SIZE - 1);
303 s->port.icount.tx++;
304 }
305 if (tx != 0xffff) {
306 max3100_calc_parity(s, &tx);
307 tx |= MAX3100_WD | (s->rts ? MAX3100_RTS : 0);
308 max3100_sr(s, tx, &rx);
309 rxchars += max3100_handlerx(s, rx);
310 }
311 }
312
Jiri Slaby2e124b42013-01-03 15:53:06 +0100313 if (rxchars > 16) {
314 tty_flip_buffer_push(&s->port.state->port);
Alan Cox7831d562009-04-08 20:13:16 +0100315 rxchars = 0;
316 }
317 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
318 uart_write_wakeup(&s->port);
319
320 } while (!s->force_end_work &&
321 !freezing(current) &&
322 ((rx & MAX3100_R) ||
323 (!uart_circ_empty(xmit) &&
324 !uart_tx_stopped(&s->port))));
325
Jiri Slaby2e124b42013-01-03 15:53:06 +0100326 if (rxchars > 0)
327 tty_flip_buffer_push(&s->port.state->port);
Alan Cox7831d562009-04-08 20:13:16 +0100328}
329
330static irqreturn_t max3100_irq(int irqno, void *dev_id)
331{
332 struct max3100_port *s = dev_id;
333
334 dev_dbg(&s->spi->dev, "%s\n", __func__);
335
336 max3100_dowork(s);
337 return IRQ_HANDLED;
338}
339
340static void max3100_enable_ms(struct uart_port *port)
341{
342 struct max3100_port *s = container_of(port,
343 struct max3100_port,
344 port);
345
346 if (s->poll_time > 0)
347 mod_timer(&s->timer, jiffies);
348 dev_dbg(&s->spi->dev, "%s\n", __func__);
349}
350
351static void max3100_start_tx(struct uart_port *port)
352{
353 struct max3100_port *s = container_of(port,
354 struct max3100_port,
355 port);
356
357 dev_dbg(&s->spi->dev, "%s\n", __func__);
358
359 max3100_dowork(s);
360}
361
362static void max3100_stop_rx(struct uart_port *port)
363{
364 struct max3100_port *s = container_of(port,
365 struct max3100_port,
366 port);
367
368 dev_dbg(&s->spi->dev, "%s\n", __func__);
369
370 s->rx_enabled = 0;
371 spin_lock(&s->conf_lock);
372 s->conf &= ~MAX3100_RM;
373 s->conf_commit = 1;
374 spin_unlock(&s->conf_lock);
375 max3100_dowork(s);
376}
377
378static unsigned int max3100_tx_empty(struct uart_port *port)
379{
380 struct max3100_port *s = container_of(port,
381 struct max3100_port,
382 port);
383
384 dev_dbg(&s->spi->dev, "%s\n", __func__);
385
386 /* may not be truly up-to-date */
387 max3100_dowork(s);
388 return s->tx_empty;
389}
390
391static unsigned int max3100_get_mctrl(struct uart_port *port)
392{
393 struct max3100_port *s = container_of(port,
394 struct max3100_port,
395 port);
396
397 dev_dbg(&s->spi->dev, "%s\n", __func__);
398
399 /* may not be truly up-to-date */
400 max3100_dowork(s);
401 /* always assert DCD and DSR since these lines are not wired */
402 return (s->cts ? TIOCM_CTS : 0) | TIOCM_DSR | TIOCM_CAR;
403}
404
405static void max3100_set_mctrl(struct uart_port *port, unsigned int mctrl)
406{
407 struct max3100_port *s = container_of(port,
408 struct max3100_port,
409 port);
410 int rts;
411
412 dev_dbg(&s->spi->dev, "%s\n", __func__);
413
414 rts = (mctrl & TIOCM_RTS) > 0;
415
416 spin_lock(&s->conf_lock);
417 if (s->rts != rts) {
418 s->rts = rts;
419 s->rts_commit = 1;
420 max3100_dowork(s);
421 }
422 spin_unlock(&s->conf_lock);
423}
424
425static void
426max3100_set_termios(struct uart_port *port, struct ktermios *termios,
427 struct ktermios *old)
428{
429 struct max3100_port *s = container_of(port,
430 struct max3100_port,
431 port);
432 int baud = 0;
433 unsigned cflag;
434 u32 param_new, param_mask, parity = 0;
Alan Cox7831d562009-04-08 20:13:16 +0100435
436 dev_dbg(&s->spi->dev, "%s\n", __func__);
Alan Cox7831d562009-04-08 20:13:16 +0100437
438 cflag = termios->c_cflag;
439 param_new = 0;
440 param_mask = 0;
441
Alan Coxeab4f5a2010-06-01 22:52:52 +0200442 baud = tty_termios_baud_rate(termios);
Alan Cox7831d562009-04-08 20:13:16 +0100443 param_new = s->conf & MAX3100_BAUD;
444 switch (baud) {
445 case 300:
446 if (s->crystal)
447 baud = s->baud;
448 else
449 param_new = 15;
450 break;
451 case 600:
452 param_new = 14 + s->crystal;
453 break;
454 case 1200:
455 param_new = 13 + s->crystal;
456 break;
457 case 2400:
458 param_new = 12 + s->crystal;
459 break;
460 case 4800:
461 param_new = 11 + s->crystal;
462 break;
463 case 9600:
464 param_new = 10 + s->crystal;
465 break;
466 case 19200:
467 param_new = 9 + s->crystal;
468 break;
469 case 38400:
470 param_new = 8 + s->crystal;
471 break;
472 case 57600:
473 param_new = 1 + s->crystal;
474 break;
475 case 115200:
476 param_new = 0 + s->crystal;
477 break;
478 case 230400:
479 if (s->crystal)
480 param_new = 0;
481 else
482 baud = s->baud;
483 break;
484 default:
485 baud = s->baud;
486 }
Alan Coxeab4f5a2010-06-01 22:52:52 +0200487 tty_termios_encode_baud_rate(termios, baud, baud);
Alan Cox7831d562009-04-08 20:13:16 +0100488 s->baud = baud;
489 param_mask |= MAX3100_BAUD;
490
491 if ((cflag & CSIZE) == CS8) {
492 param_new &= ~MAX3100_L;
493 parity &= ~MAX3100_7BIT;
494 } else {
495 param_new |= MAX3100_L;
496 parity |= MAX3100_7BIT;
497 cflag = (cflag & ~CSIZE) | CS7;
498 }
499 param_mask |= MAX3100_L;
500
501 if (cflag & CSTOPB)
502 param_new |= MAX3100_ST;
503 else
504 param_new &= ~MAX3100_ST;
505 param_mask |= MAX3100_ST;
506
507 if (cflag & PARENB) {
508 param_new |= MAX3100_PE;
509 parity |= MAX3100_PARITY_ON;
510 } else {
511 param_new &= ~MAX3100_PE;
512 parity &= ~MAX3100_PARITY_ON;
513 }
514 param_mask |= MAX3100_PE;
515
516 if (cflag & PARODD)
517 parity |= MAX3100_PARITY_ODD;
518 else
519 parity &= ~MAX3100_PARITY_ODD;
520
521 /* mask termios capabilities we don't support */
522 cflag &= ~CMSPAR;
523 termios->c_cflag = cflag;
524
525 s->port.ignore_status_mask = 0;
526 if (termios->c_iflag & IGNPAR)
527 s->port.ignore_status_mask |=
528 MAX3100_STATUS_PE | MAX3100_STATUS_FE |
529 MAX3100_STATUS_OE;
530
531 /* we are sending char from a workqueue so enable */
Jiri Slabyd6c53c02013-01-03 15:53:05 +0100532 s->port.state->port.low_latency = 1;
Alan Cox7831d562009-04-08 20:13:16 +0100533
534 if (s->poll_time > 0)
535 del_timer_sync(&s->timer);
536
537 uart_update_timeout(port, termios->c_cflag, baud);
538
539 spin_lock(&s->conf_lock);
540 s->conf = (s->conf & ~param_mask) | (param_new & param_mask);
541 s->conf_commit = 1;
542 s->parity = parity;
543 spin_unlock(&s->conf_lock);
544 max3100_dowork(s);
545
546 if (UART_ENABLE_MS(&s->port, termios->c_cflag))
547 max3100_enable_ms(&s->port);
548}
549
550static void max3100_shutdown(struct uart_port *port)
551{
552 struct max3100_port *s = container_of(port,
553 struct max3100_port,
554 port);
555
556 dev_dbg(&s->spi->dev, "%s\n", __func__);
557
558 if (s->suspending)
559 return;
560
561 s->force_end_work = 1;
562
563 if (s->poll_time > 0)
564 del_timer_sync(&s->timer);
565
566 if (s->workqueue) {
567 flush_workqueue(s->workqueue);
568 destroy_workqueue(s->workqueue);
569 s->workqueue = NULL;
570 }
571 if (s->irq)
572 free_irq(s->irq, s);
573
574 /* set shutdown mode to save power */
575 if (s->max3100_hw_suspend)
576 s->max3100_hw_suspend(1);
577 else {
578 u16 tx, rx;
579
580 tx = MAX3100_WC | MAX3100_SHDN;
581 max3100_sr(s, tx, &rx);
582 }
583}
584
585static int max3100_startup(struct uart_port *port)
586{
587 struct max3100_port *s = container_of(port,
588 struct max3100_port,
589 port);
590 char b[12];
591
592 dev_dbg(&s->spi->dev, "%s\n", __func__);
593
594 s->conf = MAX3100_RM;
595 s->baud = s->crystal ? 230400 : 115200;
596 s->rx_enabled = 1;
597
598 if (s->suspending)
599 return 0;
600
601 s->force_end_work = 0;
602 s->parity = 0;
603 s->rts = 0;
604
605 sprintf(b, "max3100-%d", s->minor);
Tejun Heo58a69cb2011-02-16 09:25:31 +0100606 s->workqueue = create_freezable_workqueue(b);
Alan Cox7831d562009-04-08 20:13:16 +0100607 if (!s->workqueue) {
608 dev_warn(&s->spi->dev, "cannot create workqueue\n");
609 return -EBUSY;
610 }
611 INIT_WORK(&s->work, max3100_work);
612
613 if (request_irq(s->irq, max3100_irq,
614 IRQF_TRIGGER_FALLING, "max3100", s) < 0) {
615 dev_warn(&s->spi->dev, "cannot allocate irq %d\n", s->irq);
616 s->irq = 0;
617 destroy_workqueue(s->workqueue);
618 s->workqueue = NULL;
619 return -EBUSY;
620 }
621
622 if (s->loopback) {
623 u16 tx, rx;
624 tx = 0x4001;
625 max3100_sr(s, tx, &rx);
626 }
627
628 if (s->max3100_hw_suspend)
629 s->max3100_hw_suspend(0);
630 s->conf_commit = 1;
631 max3100_dowork(s);
632 /* wait for clock to settle */
633 msleep(50);
634
635 max3100_enable_ms(&s->port);
636
637 return 0;
638}
639
640static const char *max3100_type(struct uart_port *port)
641{
642 struct max3100_port *s = container_of(port,
643 struct max3100_port,
644 port);
645
646 dev_dbg(&s->spi->dev, "%s\n", __func__);
647
648 return s->port.type == PORT_MAX3100 ? "MAX3100" : NULL;
649}
650
651static void max3100_release_port(struct uart_port *port)
652{
653 struct max3100_port *s = container_of(port,
654 struct max3100_port,
655 port);
656
657 dev_dbg(&s->spi->dev, "%s\n", __func__);
658}
659
660static void max3100_config_port(struct uart_port *port, int flags)
661{
662 struct max3100_port *s = container_of(port,
663 struct max3100_port,
664 port);
665
666 dev_dbg(&s->spi->dev, "%s\n", __func__);
667
668 if (flags & UART_CONFIG_TYPE)
669 s->port.type = PORT_MAX3100;
670}
671
672static int max3100_verify_port(struct uart_port *port,
673 struct serial_struct *ser)
674{
675 struct max3100_port *s = container_of(port,
676 struct max3100_port,
677 port);
678 int ret = -EINVAL;
679
680 dev_dbg(&s->spi->dev, "%s\n", __func__);
681
682 if (ser->type == PORT_UNKNOWN || ser->type == PORT_MAX3100)
683 ret = 0;
684 return ret;
685}
686
687static void max3100_stop_tx(struct uart_port *port)
688{
689 struct max3100_port *s = container_of(port,
690 struct max3100_port,
691 port);
692
693 dev_dbg(&s->spi->dev, "%s\n", __func__);
694}
695
696static int max3100_request_port(struct uart_port *port)
697{
698 struct max3100_port *s = container_of(port,
699 struct max3100_port,
700 port);
701
702 dev_dbg(&s->spi->dev, "%s\n", __func__);
703 return 0;
704}
705
706static void max3100_break_ctl(struct uart_port *port, int break_state)
707{
708 struct max3100_port *s = container_of(port,
709 struct max3100_port,
710 port);
711
712 dev_dbg(&s->spi->dev, "%s\n", __func__);
713}
714
715static struct uart_ops max3100_ops = {
716 .tx_empty = max3100_tx_empty,
717 .set_mctrl = max3100_set_mctrl,
718 .get_mctrl = max3100_get_mctrl,
719 .stop_tx = max3100_stop_tx,
720 .start_tx = max3100_start_tx,
721 .stop_rx = max3100_stop_rx,
722 .enable_ms = max3100_enable_ms,
723 .break_ctl = max3100_break_ctl,
724 .startup = max3100_startup,
725 .shutdown = max3100_shutdown,
726 .set_termios = max3100_set_termios,
727 .type = max3100_type,
728 .release_port = max3100_release_port,
729 .request_port = max3100_request_port,
730 .config_port = max3100_config_port,
731 .verify_port = max3100_verify_port,
732};
733
734static struct uart_driver max3100_uart_driver = {
735 .owner = THIS_MODULE,
736 .driver_name = "ttyMAX",
737 .dev_name = "ttyMAX",
738 .major = MAX3100_MAJOR,
739 .minor = MAX3100_MINOR,
740 .nr = MAX_MAX3100,
741};
742static int uart_driver_registered;
743
Bill Pemberton9671f092012-11-19 13:21:50 -0500744static int max3100_probe(struct spi_device *spi)
Alan Cox7831d562009-04-08 20:13:16 +0100745{
746 int i, retval;
747 struct plat_max3100 *pdata;
748 u16 tx, rx;
749
750 mutex_lock(&max3100s_lock);
751
752 if (!uart_driver_registered) {
753 uart_driver_registered = 1;
754 retval = uart_register_driver(&max3100_uart_driver);
755 if (retval) {
756 printk(KERN_ERR "Couldn't register max3100 uart driver\n");
757 mutex_unlock(&max3100s_lock);
758 return retval;
759 }
760 }
761
762 for (i = 0; i < MAX_MAX3100; i++)
763 if (!max3100s[i])
764 break;
765 if (i == MAX_MAX3100) {
766 dev_warn(&spi->dev, "too many MAX3100 chips\n");
767 mutex_unlock(&max3100s_lock);
768 return -ENOMEM;
769 }
770
771 max3100s[i] = kzalloc(sizeof(struct max3100_port), GFP_KERNEL);
772 if (!max3100s[i]) {
773 dev_warn(&spi->dev,
774 "kmalloc for max3100 structure %d failed!\n", i);
775 mutex_unlock(&max3100s_lock);
776 return -ENOMEM;
777 }
778 max3100s[i]->spi = spi;
779 max3100s[i]->irq = spi->irq;
780 spin_lock_init(&max3100s[i]->conf_lock);
Jingoo Han31bdfc62013-04-05 10:54:05 +0900781 spi_set_drvdata(spi, max3100s[i]);
Alan Cox7831d562009-04-08 20:13:16 +0100782 pdata = spi->dev.platform_data;
783 max3100s[i]->crystal = pdata->crystal;
784 max3100s[i]->loopback = pdata->loopback;
785 max3100s[i]->poll_time = pdata->poll_time * HZ / 1000;
786 if (pdata->poll_time > 0 && max3100s[i]->poll_time == 0)
787 max3100s[i]->poll_time = 1;
788 max3100s[i]->max3100_hw_suspend = pdata->max3100_hw_suspend;
789 max3100s[i]->minor = i;
790 init_timer(&max3100s[i]->timer);
791 max3100s[i]->timer.function = max3100_timeout;
792 max3100s[i]->timer.data = (unsigned long) max3100s[i];
793
794 dev_dbg(&spi->dev, "%s: adding port %d\n", __func__, i);
795 max3100s[i]->port.irq = max3100s[i]->irq;
796 max3100s[i]->port.uartclk = max3100s[i]->crystal ? 3686400 : 1843200;
797 max3100s[i]->port.fifosize = 16;
798 max3100s[i]->port.ops = &max3100_ops;
799 max3100s[i]->port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF;
800 max3100s[i]->port.line = i;
801 max3100s[i]->port.type = PORT_MAX3100;
802 max3100s[i]->port.dev = &spi->dev;
803 retval = uart_add_one_port(&max3100_uart_driver, &max3100s[i]->port);
804 if (retval < 0)
805 dev_warn(&spi->dev,
806 "uart_add_one_port failed for line %d with error %d\n",
807 i, retval);
808
809 /* set shutdown mode to save power. Will be woken-up on open */
810 if (max3100s[i]->max3100_hw_suspend)
811 max3100s[i]->max3100_hw_suspend(1);
812 else {
813 tx = MAX3100_WC | MAX3100_SHDN;
814 max3100_sr(max3100s[i], tx, &rx);
815 }
816 mutex_unlock(&max3100s_lock);
817 return 0;
818}
819
Bill Pembertonae8d8a12012-11-19 13:26:18 -0500820static int max3100_remove(struct spi_device *spi)
Alan Cox7831d562009-04-08 20:13:16 +0100821{
Jingoo Han31bdfc62013-04-05 10:54:05 +0900822 struct max3100_port *s = spi_get_drvdata(spi);
Alan Cox7831d562009-04-08 20:13:16 +0100823 int i;
824
825 mutex_lock(&max3100s_lock);
826
827 /* find out the index for the chip we are removing */
828 for (i = 0; i < MAX_MAX3100; i++)
Alan Cox41fda9c2012-09-17 12:00:44 +0100829 if (max3100s[i] == s) {
830 dev_dbg(&spi->dev, "%s: removing port %d\n", __func__, i);
831 uart_remove_one_port(&max3100_uart_driver, &max3100s[i]->port);
832 kfree(max3100s[i]);
833 max3100s[i] = NULL;
Alan Cox7831d562009-04-08 20:13:16 +0100834 break;
Alan Cox41fda9c2012-09-17 12:00:44 +0100835 }
Alan Cox7831d562009-04-08 20:13:16 +0100836
Alan Cox41fda9c2012-09-17 12:00:44 +0100837 WARN_ON(i == MAX_MAX3100);
838
Alan Cox7831d562009-04-08 20:13:16 +0100839 /* check if this is the last chip we have */
840 for (i = 0; i < MAX_MAX3100; i++)
841 if (max3100s[i]) {
842 mutex_unlock(&max3100s_lock);
843 return 0;
844 }
845 pr_debug("removing max3100 driver\n");
846 uart_unregister_driver(&max3100_uart_driver);
847
848 mutex_unlock(&max3100s_lock);
849 return 0;
850}
851
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100852#ifdef CONFIG_PM_SLEEP
Alan Cox7831d562009-04-08 20:13:16 +0100853
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100854static int max3100_suspend(struct device *dev)
Alan Cox7831d562009-04-08 20:13:16 +0100855{
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100856 struct max3100_port *s = dev_get_drvdata(dev);
Alan Cox7831d562009-04-08 20:13:16 +0100857
858 dev_dbg(&s->spi->dev, "%s\n", __func__);
859
860 disable_irq(s->irq);
861
862 s->suspending = 1;
863 uart_suspend_port(&max3100_uart_driver, &s->port);
864
865 if (s->max3100_hw_suspend)
866 s->max3100_hw_suspend(1);
867 else {
868 /* no HW suspend, so do SW one */
869 u16 tx, rx;
870
871 tx = MAX3100_WC | MAX3100_SHDN;
872 max3100_sr(s, tx, &rx);
873 }
874 return 0;
875}
876
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100877static int max3100_resume(struct device *dev)
Alan Cox7831d562009-04-08 20:13:16 +0100878{
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100879 struct max3100_port *s = dev_get_drvdata(dev);
Alan Cox7831d562009-04-08 20:13:16 +0100880
881 dev_dbg(&s->spi->dev, "%s\n", __func__);
882
883 if (s->max3100_hw_suspend)
884 s->max3100_hw_suspend(0);
885 uart_resume_port(&max3100_uart_driver, &s->port);
886 s->suspending = 0;
887
888 enable_irq(s->irq);
889
890 s->conf_commit = 1;
891 if (s->workqueue)
892 max3100_dowork(s);
893
894 return 0;
895}
896
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100897static SIMPLE_DEV_PM_OPS(max3100_pm_ops, max3100_suspend, max3100_resume);
898#define MAX3100_PM_OPS (&max3100_pm_ops)
899
Alan Cox7831d562009-04-08 20:13:16 +0100900#else
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100901#define MAX3100_PM_OPS NULL
Alan Cox7831d562009-04-08 20:13:16 +0100902#endif
903
904static struct spi_driver max3100_driver = {
905 .driver = {
906 .name = "max3100",
Alan Cox7831d562009-04-08 20:13:16 +0100907 .owner = THIS_MODULE,
Lars-Peter Clausenc47ddc22013-03-11 18:44:49 +0100908 .pm = MAX3100_PM_OPS,
Alan Cox7831d562009-04-08 20:13:16 +0100909 },
Alan Cox7831d562009-04-08 20:13:16 +0100910 .probe = max3100_probe,
Bill Pemberton2d47b712012-11-19 13:21:34 -0500911 .remove = max3100_remove,
Alan Cox7831d562009-04-08 20:13:16 +0100912};
913
Devendra Nagac0fc2082012-08-24 03:34:42 +0530914module_spi_driver(max3100_driver);
Alan Cox7831d562009-04-08 20:13:16 +0100915
916MODULE_DESCRIPTION("MAX3100 driver");
917MODULE_AUTHOR("Christian Pellegrin <chripell@evolware.org>");
918MODULE_LICENSE("GPL");
Anton Vorontsove0626e32009-09-22 16:46:08 -0700919MODULE_ALIAS("spi:max3100");