blob: 0e76ef12e4c60d996fde89cef341f5dc05163160 [file] [log] [blame]
Guenter Roeck4453d732010-08-09 17:21:08 -07001Kernel driver jc42
2==================
3
4Supported chips:
5 * Analog Devices ADT7408
6 Prefix: 'adt7408'
7 Addresses scanned: I2C 0x18 - 0x1f
8 Datasheets:
9 http://www.analog.com/static/imported-files/data_sheets/ADT7408.pdf
10 * IDT TSE2002B3, TS3000B3
11 Prefix: 'tse2002b3', 'ts3000b3'
12 Addresses scanned: I2C 0x18 - 0x1f
13 Datasheets:
14 http://www.idt.com/products/getdoc.cfm?docid=18715691
15 http://www.idt.com/products/getdoc.cfm?docid=18715692
16 * Maxim MAX6604
17 Prefix: 'max6604'
18 Addresses scanned: I2C 0x18 - 0x1f
19 Datasheets:
20 http://datasheets.maxim-ic.com/en/ds/MAX6604.pdf
21 * Microchip MCP9805, MCP98242, MCP98243, MCP9843
22 Prefixes: 'mcp9805', 'mcp98242', 'mcp98243', 'mcp9843'
23 Addresses scanned: I2C 0x18 - 0x1f
24 Datasheets:
25 http://ww1.microchip.com/downloads/en/DeviceDoc/21977b.pdf
26 http://ww1.microchip.com/downloads/en/DeviceDoc/21996a.pdf
27 http://ww1.microchip.com/downloads/en/DeviceDoc/22153c.pdf
28 * NXP Semiconductors SE97, SE97B
29 Prefix: 'se97'
30 Addresses scanned: I2C 0x18 - 0x1f
31 Datasheets:
32 http://www.nxp.com/documents/data_sheet/SE97.pdf
33 http://www.nxp.com/documents/data_sheet/SE97B.pdf
34 * NXP Semiconductors SE98
35 Prefix: 'se98'
36 Addresses scanned: I2C 0x18 - 0x1f
37 Datasheets:
38 http://www.nxp.com/documents/data_sheet/SE98.pdf
39 * ON Semiconductor CAT34TS02, CAT6095
40 Prefix: 'cat34ts02', 'cat6095'
41 Addresses scanned: I2C 0x18 - 0x1f
42 Datasheet:
43 http://www.onsemi.com/pub_link/Collateral/CAT34TS02-D.PDF
44 http://www.onsemi.com/pub/Collateral/CAT6095-D.PDF
45 * ST Microelectronics STTS424, STTS424E02
46 Prefix: 'stts424'
47 Addresses scanned: I2C 0x18 - 0x1f
48 Datasheets:
49 http://www.st.com/stonline/products/literature/ds/13447/stts424.pdf
50 http://www.st.com/stonline/products/literature/ds/13448/stts424e02.pdf
51 * JEDEC JC 42.4 compliant temperature sensor chips
52 Prefix: 'jc42'
53 Addresses scanned: I2C 0x18 - 0x1f
54 Datasheet: -
55
56Author:
57 Guenter Roeck <guenter.roeck@ericsson.com>
58
59
60Description
61-----------
62
63This driver implements support for JEDEC JC 42.4 compliant temperature sensors.
64The driver auto-detects the chips listed above, but can be manually instantiated
65to support other JC 42.4 compliant chips.
66
67Example: the following will load the driver for a generic JC 42.4 compliant
68temperature sensor at address 0x18 on I2C bus #1:
69
70# modprobe jc42
71# echo jc42 0x18 > /sys/bus/i2c/devices/i2c-1/new_device
72
73A JC 42.4 compliant chip supports a single temperature sensor. Minimum, maximum,
74and critical temperature can be configured. There are alarms for high, low,
75and critical thresholds.
76
77There is also an hysteresis to control the thresholds for resetting alarms.
78Per JC 42.4 specification, the hysteresis threshold can be configured to 0, 1.5,
793.0, and 6.0 degrees C. Configured hysteresis values will be rounded to those
80limits. The chip supports only a single register to configure the hysteresis,
81which applies to all limits. This register can be written by writing into
82temp1_crit_hyst. Other hysteresis attributes are read-only.
83
84Sysfs entries
85-------------
86
87temp1_input Temperature (RO)
88temp1_min Minimum temperature (RW)
89temp1_max Maximum temperature (RW)
90temp1_crit Critical high temperature (RW)
91
92temp1_crit_hyst Critical hysteresis temperature (RW)
93temp1_max_hyst Maximum hysteresis temperature (RO)
94
95temp1_min_alarm Temperature low alarm
96temp1_max_alarm Temperature high alarm
97temp1_crit_alarm Temperature critical alarm