blob: b330438ac662631bdc720426fdb7cad5a539cd4c [file] [log] [blame]
Linus Torvalds1da177e2005-04-16 15:20:36 -07001/*
2 * linux/drivers/acorn/scsi/acornscsi.c
3 *
4 * Acorn SCSI 3 driver
5 * By R.M.King.
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License version 2 as
9 * published by the Free Software Foundation.
10 *
11 * Abandoned using the Select and Transfer command since there were
12 * some nasty races between our software and the target devices that
13 * were not easy to solve, and the device errata had a lot of entries
14 * for this command, some of them quite nasty...
15 *
16 * Changelog:
17 * 26-Sep-1997 RMK Re-jigged to use the queue module.
18 * Re-coded state machine to be based on driver
19 * state not scsi state. Should be easier to debug.
20 * Added acornscsi_release to clean up properly.
21 * Updated proc/scsi reporting.
22 * 05-Oct-1997 RMK Implemented writing to SCSI devices.
23 * 06-Oct-1997 RMK Corrected small (non-serious) bug with the connect/
24 * reconnect race condition causing a warning message.
25 * 12-Oct-1997 RMK Added catch for re-entering interrupt routine.
26 * 15-Oct-1997 RMK Improved handling of commands.
27 * 27-Jun-1998 RMK Changed asm/delay.h to linux/delay.h.
28 * 13-Dec-1998 RMK Better abort code and command handling. Extra state
29 * transitions added to allow dodgy devices to work.
30 */
31#define DEBUG_NO_WRITE 1
32#define DEBUG_QUEUES 2
33#define DEBUG_DMA 4
34#define DEBUG_ABORT 8
35#define DEBUG_DISCON 16
36#define DEBUG_CONNECT 32
37#define DEBUG_PHASES 64
38#define DEBUG_WRITE 128
39#define DEBUG_LINK 256
40#define DEBUG_MESSAGES 512
41#define DEBUG_RESET 1024
42#define DEBUG_ALL (DEBUG_RESET|DEBUG_MESSAGES|DEBUG_LINK|DEBUG_WRITE|\
43 DEBUG_PHASES|DEBUG_CONNECT|DEBUG_DISCON|DEBUG_ABORT|\
44 DEBUG_DMA|DEBUG_QUEUES)
45
46/* DRIVER CONFIGURATION
47 *
48 * SCSI-II Tagged queue support.
49 *
50 * I don't have any SCSI devices that support it, so it is totally untested
51 * (except to make sure that it doesn't interfere with any non-tagging
52 * devices). It is not fully implemented either - what happens when a
53 * tagging device reconnects???
54 *
55 * You can tell if you have a device that supports tagged queueing my
56 * cating (eg) /proc/scsi/acornscsi/0 and see if the SCSI revision is reported
57 * as '2 TAG'.
58 *
59 * Also note that CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE is normally set in the config
60 * scripts, but disabled here. Once debugged, remove the #undef, otherwise to debug,
61 * comment out the undef.
62 */
63#undef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
64/*
65 * SCSI-II Linked command support.
66 *
67 * The higher level code doesn't support linked commands yet, and so the option
68 * is undef'd here.
69 */
70#undef CONFIG_SCSI_ACORNSCSI_LINK
71/*
72 * SCSI-II Synchronous transfer support.
73 *
74 * Tried and tested...
75 *
76 * SDTR_SIZE - maximum number of un-acknowledged bytes (0 = off, 12 = max)
77 * SDTR_PERIOD - period of REQ signal (min=125, max=1020)
78 * DEFAULT_PERIOD - default REQ period.
79 */
80#define SDTR_SIZE 12
81#define SDTR_PERIOD 125
82#define DEFAULT_PERIOD 500
83
84/*
85 * Debugging information
86 *
87 * DEBUG - bit mask from list above
88 * DEBUG_TARGET - is defined to the target number if you want to debug
89 * a specific target. [only recon/write/dma].
90 */
91#define DEBUG (DEBUG_RESET|DEBUG_WRITE|DEBUG_NO_WRITE)
92/* only allow writing to SCSI device 0 */
93#define NO_WRITE 0xFE
94/*#define DEBUG_TARGET 2*/
95/*
96 * Select timeout time (in 10ms units)
97 *
98 * This is the timeout used between the start of selection and the WD33C93
99 * chip deciding that the device isn't responding.
100 */
101#define TIMEOUT_TIME 10
102/*
Lucas De Marchi25985ed2011-03-30 22:57:33 -0300103 * Define this if you want to have verbose explanation of SCSI
Linus Torvalds1da177e2005-04-16 15:20:36 -0700104 * status/messages.
105 */
106#undef CONFIG_ACORNSCSI_CONSTANTS
107/*
108 * Define this if you want to use the on board DMAC [don't remove this option]
109 * If not set, then use PIO mode (not currently supported).
110 */
111#define USE_DMAC
112
113/*
114 * ====================================================================================
115 */
116
117#ifdef DEBUG_TARGET
118#define DBG(cmd,xxx...) \
119 if (cmd->device->id == DEBUG_TARGET) { \
120 xxx; \
121 }
122#else
123#define DBG(cmd,xxx...) xxx
124#endif
125
Linus Torvalds1da177e2005-04-16 15:20:36 -0700126#include <linux/module.h>
127#include <linux/kernel.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700128#include <linux/string.h>
129#include <linux/signal.h>
130#include <linux/errno.h>
131#include <linux/proc_fs.h>
132#include <linux/ioport.h>
133#include <linux/blkdev.h>
134#include <linux/delay.h>
135#include <linux/interrupt.h>
136#include <linux/init.h>
137#include <linux/bitops.h>
Russell Kinga796ef72008-04-19 15:37:44 +0100138#include <linux/stringify.h>
Russell Kinge95a1b62008-04-19 15:42:57 +0100139#include <linux/io.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700140
Linus Torvalds1da177e2005-04-16 15:20:36 -0700141#include <asm/ecard.h>
142
143#include "../scsi.h"
db9dff32005-04-03 14:53:59 -0500144#include <scsi/scsi_dbg.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700145#include <scsi/scsi_host.h>
Matthew Wilcox1abfd372005-12-15 16:22:01 -0500146#include <scsi/scsi_transport_spi.h>
Linus Torvalds1da177e2005-04-16 15:20:36 -0700147#include "acornscsi.h"
148#include "msgqueue.h"
149#include "scsi.h"
150
151#include <scsi/scsicam.h>
152
153#define VER_MAJOR 2
154#define VER_MINOR 0
155#define VER_PATCH 6
156
157#ifndef ABORT_TAG
158#define ABORT_TAG 0xd
159#else
160#error "Yippee! ABORT TAG is now defined! Remove this error!"
161#endif
162
163#ifdef CONFIG_SCSI_ACORNSCSI_LINK
164#error SCSI2 LINKed commands not supported (yet)!
165#endif
166
167#ifdef USE_DMAC
168/*
169 * DMAC setup parameters
170 */
171#define INIT_DEVCON0 (DEVCON0_RQL|DEVCON0_EXW|DEVCON0_CMP)
172#define INIT_DEVCON1 (DEVCON1_BHLD)
173#define DMAC_READ (MODECON_READ)
174#define DMAC_WRITE (MODECON_WRITE)
175#define INIT_SBICDMA (CTRL_DMABURST)
176
177#define scsi_xferred have_data_in
178
179/*
180 * Size of on-board DMA buffer
181 */
182#define DMAC_BUFFER_SIZE 65536
183#endif
184
185#define STATUS_BUFFER_TO_PRINT 24
186
187unsigned int sdtr_period = SDTR_PERIOD;
188unsigned int sdtr_size = SDTR_SIZE;
189
Henneee0ca6b2006-10-01 13:18:37 +0200190static void acornscsi_done(AS_Host *host, struct scsi_cmnd **SCpntp,
191 unsigned int result);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700192static int acornscsi_reconnect_finish(AS_Host *host);
193static void acornscsi_dma_cleanup(AS_Host *host);
194static void acornscsi_abortcmd(AS_Host *host, unsigned char tag);
195
196/* ====================================================================================
197 * Miscellaneous
198 */
199
Russell Kinge95a1b62008-04-19 15:42:57 +0100200/* Offsets from MEMC base */
201#define SBIC_REGIDX 0x2000
202#define SBIC_REGVAL 0x2004
203#define DMAC_OFFSET 0x3000
204
205/* Offsets from FAST IOC base */
206#define INT_REG 0x2000
207#define PAGE_REG 0x3000
208
Russell Kingffd78582008-04-19 14:26:18 +0100209static inline void sbic_arm_write(AS_Host *host, unsigned int reg, unsigned int value)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700210{
Russell Kinge95a1b62008-04-19 15:42:57 +0100211 writeb(reg, host->base + SBIC_REGIDX);
212 writeb(value, host->base + SBIC_REGVAL);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700213}
214
Russell Kingffd78582008-04-19 14:26:18 +0100215static inline int sbic_arm_read(AS_Host *host, unsigned int reg)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700216{
217 if(reg == SBIC_ASR)
Russell Kinge95a1b62008-04-19 15:42:57 +0100218 return readl(host->base + SBIC_REGIDX) & 255;
219 writeb(reg, host->base + SBIC_REGIDX);
220 return readl(host->base + SBIC_REGVAL) & 255;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700221}
222
Russell Kinge95a1b62008-04-19 15:42:57 +0100223#define sbic_arm_writenext(host, val) writeb((val), (host)->base + SBIC_REGVAL)
224#define sbic_arm_readnext(host) readb((host)->base + SBIC_REGVAL)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700225
226#ifdef USE_DMAC
Russell Kingffd78582008-04-19 14:26:18 +0100227#define dmac_read(host,reg) \
Russell Kinge95a1b62008-04-19 15:42:57 +0100228 readb((host)->base + DMAC_OFFSET + ((reg) << 2))
Linus Torvalds1da177e2005-04-16 15:20:36 -0700229
Russell Kingffd78582008-04-19 14:26:18 +0100230#define dmac_write(host,reg,value) \
Russell Kinge95a1b62008-04-19 15:42:57 +0100231 ({ writeb((value), (host)->base + DMAC_OFFSET + ((reg) << 2)); })
Linus Torvalds1da177e2005-04-16 15:20:36 -0700232
Russell Kinge95a1b62008-04-19 15:42:57 +0100233#define dmac_clearintr(host) writeb(0, (host)->fast + INT_REG)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700234
Russell Kingffd78582008-04-19 14:26:18 +0100235static inline unsigned int dmac_address(AS_Host *host)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700236{
Russell Kingffd78582008-04-19 14:26:18 +0100237 return dmac_read(host, DMAC_TXADRHI) << 16 |
238 dmac_read(host, DMAC_TXADRMD) << 8 |
239 dmac_read(host, DMAC_TXADRLO);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700240}
241
242static
243void acornscsi_dumpdma(AS_Host *host, char *where)
244{
245 unsigned int mode, addr, len;
246
Russell Kingffd78582008-04-19 14:26:18 +0100247 mode = dmac_read(host, DMAC_MODECON);
248 addr = dmac_address(host);
249 len = dmac_read(host, DMAC_TXCNTHI) << 8 |
250 dmac_read(host, DMAC_TXCNTLO);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700251
252 printk("scsi%d: %s: DMAC %02x @%06x+%04x msk %02x, ",
253 host->host->host_no, where,
254 mode, addr, (len + 1) & 0xffff,
Russell Kingffd78582008-04-19 14:26:18 +0100255 dmac_read(host, DMAC_MASKREG));
Linus Torvalds1da177e2005-04-16 15:20:36 -0700256
257 printk("DMA @%06x, ", host->dma.start_addr);
258 printk("BH @%p +%04x, ", host->scsi.SCp.ptr,
259 host->scsi.SCp.this_residual);
260 printk("DT @+%04x ST @+%04x", host->dma.transferred,
261 host->scsi.SCp.scsi_xferred);
262 printk("\n");
263}
264#endif
265
266static
267unsigned long acornscsi_sbic_xfcount(AS_Host *host)
268{
269 unsigned long length;
270
Russell Kingffd78582008-04-19 14:26:18 +0100271 length = sbic_arm_read(host, SBIC_TRANSCNTH) << 16;
272 length |= sbic_arm_readnext(host) << 8;
273 length |= sbic_arm_readnext(host);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700274
275 return length;
276}
277
278static int
279acornscsi_sbic_wait(AS_Host *host, int stat_mask, int stat, int timeout, char *msg)
280{
281 int asr;
282
283 do {
Russell Kingffd78582008-04-19 14:26:18 +0100284 asr = sbic_arm_read(host, SBIC_ASR);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700285
286 if ((asr & stat_mask) == stat)
287 return 0;
288
289 udelay(1);
290 } while (--timeout);
291
292 printk("scsi%d: timeout while %s\n", host->host->host_no, msg);
293
294 return -1;
295}
296
297static
298int acornscsi_sbic_issuecmd(AS_Host *host, int command)
299{
300 if (acornscsi_sbic_wait(host, ASR_CIP, 0, 1000, "issuing command"))
301 return -1;
302
Russell Kingffd78582008-04-19 14:26:18 +0100303 sbic_arm_write(host, SBIC_CMND, command);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700304
305 return 0;
306}
307
308static void
309acornscsi_csdelay(unsigned int cs)
310{
311 unsigned long target_jiffies, flags;
312
313 target_jiffies = jiffies + 1 + cs * HZ / 100;
314
315 local_save_flags(flags);
316 local_irq_enable();
317
318 while (time_before(jiffies, target_jiffies)) barrier();
319
320 local_irq_restore(flags);
321}
322
323static
324void acornscsi_resetcard(AS_Host *host)
325{
326 unsigned int i, timeout;
327
328 /* assert reset line */
329 host->card.page_reg = 0x80;
Russell Kinge95a1b62008-04-19 15:42:57 +0100330 writeb(host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700331
332 /* wait 3 cs. SCSI standard says 25ms. */
333 acornscsi_csdelay(3);
334
335 host->card.page_reg = 0;
Russell Kinge95a1b62008-04-19 15:42:57 +0100336 writeb(host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700337
338 /*
339 * Should get a reset from the card
340 */
341 timeout = 1000;
342 do {
Russell Kinge95a1b62008-04-19 15:42:57 +0100343 if (readb(host->fast + INT_REG) & 8)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700344 break;
345 udelay(1);
346 } while (--timeout);
347
348 if (timeout == 0)
349 printk("scsi%d: timeout while resetting card\n",
350 host->host->host_no);
351
Russell Kingffd78582008-04-19 14:26:18 +0100352 sbic_arm_read(host, SBIC_ASR);
353 sbic_arm_read(host, SBIC_SSR);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700354
355 /* setup sbic - WD33C93A */
Russell Kingffd78582008-04-19 14:26:18 +0100356 sbic_arm_write(host, SBIC_OWNID, OWNID_EAF | host->host->this_id);
357 sbic_arm_write(host, SBIC_CMND, CMND_RESET);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700358
359 /*
360 * Command should cause a reset interrupt
361 */
362 timeout = 1000;
363 do {
Russell Kinge95a1b62008-04-19 15:42:57 +0100364 if (readb(host->fast + INT_REG) & 8)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700365 break;
366 udelay(1);
367 } while (--timeout);
368
369 if (timeout == 0)
370 printk("scsi%d: timeout while resetting card\n",
371 host->host->host_no);
372
Russell Kingffd78582008-04-19 14:26:18 +0100373 sbic_arm_read(host, SBIC_ASR);
374 if (sbic_arm_read(host, SBIC_SSR) != 0x01)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700375 printk(KERN_CRIT "scsi%d: WD33C93A didn't give enhanced reset interrupt\n",
376 host->host->host_no);
377
Russell Kingffd78582008-04-19 14:26:18 +0100378 sbic_arm_write(host, SBIC_CTRL, INIT_SBICDMA | CTRL_IDI);
379 sbic_arm_write(host, SBIC_TIMEOUT, TIMEOUT_TIME);
380 sbic_arm_write(host, SBIC_SYNCHTRANSFER, SYNCHTRANSFER_2DBA);
381 sbic_arm_write(host, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700382
383 host->card.page_reg = 0x40;
Russell Kinge95a1b62008-04-19 15:42:57 +0100384 writeb(host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700385
386 /* setup dmac - uPC71071 */
Russell Kingffd78582008-04-19 14:26:18 +0100387 dmac_write(host, DMAC_INIT, 0);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700388#ifdef USE_DMAC
Russell Kingffd78582008-04-19 14:26:18 +0100389 dmac_write(host, DMAC_INIT, INIT_8BIT);
390 dmac_write(host, DMAC_CHANNEL, CHANNEL_0);
391 dmac_write(host, DMAC_DEVCON0, INIT_DEVCON0);
392 dmac_write(host, DMAC_DEVCON1, INIT_DEVCON1);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700393#endif
394
395 host->SCpnt = NULL;
396 host->scsi.phase = PHASE_IDLE;
397 host->scsi.disconnectable = 0;
398
399 memset(host->busyluns, 0, sizeof(host->busyluns));
400
401 for (i = 0; i < 8; i++) {
402 host->device[i].sync_state = SYNC_NEGOCIATE;
403 host->device[i].disconnect_ok = 1;
404 }
405
406 /* wait 25 cs. SCSI standard says 250ms. */
407 acornscsi_csdelay(25);
408}
409
410/*=============================================================================================
411 * Utility routines (eg. debug)
412 */
413#ifdef CONFIG_ACORNSCSI_CONSTANTS
414static char *acornscsi_interrupttype[] = {
415 "rst", "suc", "p/a", "3",
416 "term", "5", "6", "7",
417 "serv", "9", "a", "b",
418 "c", "d", "e", "f"
419};
420
421static signed char acornscsi_map[] = {
422 0, 1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
423 -1, 2, -1, -1, -1, -1, 3, -1, 4, 5, 6, 7, 8, 9, 10, 11,
424 12, 13, 14, -1, -1, -1, -1, -1, 4, 5, 6, 7, 8, 9, 10, 11,
425 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
426 15, 16, 17, 18, 19, -1, -1, 20, 4, 5, 6, 7, 8, 9, 10, 11,
427 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
428 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
429 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
430 21, 22, -1, -1, -1, 23, -1, -1, 4, 5, 6, 7, 8, 9, 10, 11,
431 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
432 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
433 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
434 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
435 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
436 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1,
437 -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1, -1
438};
439
440static char *acornscsi_interruptcode[] = {
441 /* 0 */
442 "reset - normal mode", /* 00 */
443 "reset - advanced mode", /* 01 */
444
445 /* 2 */
446 "sel", /* 11 */
447 "sel+xfer", /* 16 */
448 "data-out", /* 18 */
449 "data-in", /* 19 */
450 "cmd", /* 1A */
451 "stat", /* 1B */
452 "??-out", /* 1C */
453 "??-in", /* 1D */
454 "msg-out", /* 1E */
455 "msg-in", /* 1F */
456
457 /* 12 */
458 "/ACK asserted", /* 20 */
459 "save-data-ptr", /* 21 */
460 "{re}sel", /* 22 */
461
462 /* 15 */
463 "inv cmd", /* 40 */
464 "unexpected disconnect", /* 41 */
465 "sel timeout", /* 42 */
466 "P err", /* 43 */
467 "P err+ATN", /* 44 */
468 "bad status byte", /* 47 */
469
470 /* 21 */
471 "resel, no id", /* 80 */
472 "resel", /* 81 */
473 "discon", /* 85 */
474};
475
476static
477void print_scsi_status(unsigned int ssr)
478{
479 if (acornscsi_map[ssr] != -1)
480 printk("%s:%s",
481 acornscsi_interrupttype[(ssr >> 4)],
482 acornscsi_interruptcode[acornscsi_map[ssr]]);
483 else
484 printk("%X:%X", ssr >> 4, ssr & 0x0f);
485}
486#endif
487
488static
489void print_sbic_status(int asr, int ssr, int cmdphase)
490{
491#ifdef CONFIG_ACORNSCSI_CONSTANTS
492 printk("sbic: %c%c%c%c%c%c ",
493 asr & ASR_INT ? 'I' : 'i',
494 asr & ASR_LCI ? 'L' : 'l',
495 asr & ASR_BSY ? 'B' : 'b',
496 asr & ASR_CIP ? 'C' : 'c',
497 asr & ASR_PE ? 'P' : 'p',
498 asr & ASR_DBR ? 'D' : 'd');
499 printk("scsi: ");
500 print_scsi_status(ssr);
501 printk(" ph %02X\n", cmdphase);
502#else
503 printk("sbic: %02X scsi: %X:%X ph: %02X\n",
504 asr, (ssr & 0xf0)>>4, ssr & 0x0f, cmdphase);
505#endif
506}
507
508static void
509acornscsi_dumplogline(AS_Host *host, int target, int line)
510{
511 unsigned long prev;
512 signed int ptr;
513
514 ptr = host->status_ptr[target] - STATUS_BUFFER_TO_PRINT;
515 if (ptr < 0)
516 ptr += STATUS_BUFFER_SIZE;
517
518 printk("%c: %3s:", target == 8 ? 'H' : '0' + target,
519 line == 0 ? "ph" : line == 1 ? "ssr" : "int");
520
521 prev = host->status[target][ptr].when;
522
523 for (; ptr != host->status_ptr[target]; ptr = (ptr + 1) & (STATUS_BUFFER_SIZE - 1)) {
524 unsigned long time_diff;
525
526 if (!host->status[target][ptr].when)
527 continue;
528
529 switch (line) {
530 case 0:
531 printk("%c%02X", host->status[target][ptr].irq ? '-' : ' ',
532 host->status[target][ptr].ph);
533 break;
534
535 case 1:
536 printk(" %02X", host->status[target][ptr].ssr);
537 break;
538
539 case 2:
540 time_diff = host->status[target][ptr].when - prev;
541 prev = host->status[target][ptr].when;
542 if (time_diff == 0)
543 printk("==^");
544 else if (time_diff >= 100)
545 printk(" ");
546 else
547 printk(" %02ld", time_diff);
548 break;
549 }
550 }
551
552 printk("\n");
553}
554
555static
556void acornscsi_dumplog(AS_Host *host, int target)
557{
558 do {
559 acornscsi_dumplogline(host, target, 0);
560 acornscsi_dumplogline(host, target, 1);
561 acornscsi_dumplogline(host, target, 2);
562
563 if (target == 8)
564 break;
565
566 target = 8;
567 } while (1);
568}
569
570static
571char acornscsi_target(AS_Host *host)
572{
573 if (host->SCpnt)
574 return '0' + host->SCpnt->device->id;
575 return 'H';
576}
577
578/*
579 * Prototype: cmdtype_t acornscsi_cmdtype(int command)
580 * Purpose : differentiate READ from WRITE from other commands
581 * Params : command - command to interpret
582 * Returns : CMD_READ - command reads data,
583 * CMD_WRITE - command writes data,
584 * CMD_MISC - everything else
585 */
586static inline
587cmdtype_t acornscsi_cmdtype(int command)
588{
589 switch (command) {
590 case WRITE_6: case WRITE_10: case WRITE_12:
591 return CMD_WRITE;
592 case READ_6: case READ_10: case READ_12:
593 return CMD_READ;
594 default:
595 return CMD_MISC;
596 }
597}
598
599/*
600 * Prototype: int acornscsi_datadirection(int command)
601 * Purpose : differentiate between commands that have a DATA IN phase
602 * and a DATA OUT phase
603 * Params : command - command to interpret
604 * Returns : DATADIR_OUT - data out phase expected
605 * DATADIR_IN - data in phase expected
606 */
607static
608datadir_t acornscsi_datadirection(int command)
609{
610 switch (command) {
611 case CHANGE_DEFINITION: case COMPARE: case COPY:
612 case COPY_VERIFY: case LOG_SELECT: case MODE_SELECT:
613 case MODE_SELECT_10: case SEND_DIAGNOSTIC: case WRITE_BUFFER:
614 case FORMAT_UNIT: case REASSIGN_BLOCKS: case RESERVE:
615 case SEARCH_EQUAL: case SEARCH_HIGH: case SEARCH_LOW:
616 case WRITE_6: case WRITE_10: case WRITE_VERIFY:
617 case UPDATE_BLOCK: case WRITE_LONG: case WRITE_SAME:
618 case SEARCH_HIGH_12: case SEARCH_EQUAL_12: case SEARCH_LOW_12:
619 case WRITE_12: case WRITE_VERIFY_12: case SET_WINDOW:
620 case MEDIUM_SCAN: case SEND_VOLUME_TAG: case 0xea:
621 return DATADIR_OUT;
622 default:
623 return DATADIR_IN;
624 }
625}
626
627/*
628 * Purpose : provide values for synchronous transfers with 33C93.
629 * Copyright: Copyright (c) 1996 John Shifflett, GeoLog Consulting
630 * Modified by Russell King for 8MHz WD33C93A
631 */
632static struct sync_xfer_tbl {
633 unsigned int period_ns;
634 unsigned char reg_value;
635} sync_xfer_table[] = {
636 { 1, 0x20 }, { 249, 0x20 }, { 374, 0x30 },
637 { 499, 0x40 }, { 624, 0x50 }, { 749, 0x60 },
638 { 874, 0x70 }, { 999, 0x00 }, { 0, 0 }
639};
640
641/*
642 * Prototype: int acornscsi_getperiod(unsigned char syncxfer)
643 * Purpose : period for the synchronous transfer setting
644 * Params : syncxfer SYNCXFER register value
645 * Returns : period in ns.
646 */
647static
648int acornscsi_getperiod(unsigned char syncxfer)
649{
650 int i;
651
652 syncxfer &= 0xf0;
653 if (syncxfer == 0x10)
654 syncxfer = 0;
655
656 for (i = 1; sync_xfer_table[i].period_ns; i++)
657 if (syncxfer == sync_xfer_table[i].reg_value)
658 return sync_xfer_table[i].period_ns;
659 return 0;
660}
661
662/*
663 * Prototype: int round_period(unsigned int period)
664 * Purpose : return index into above table for a required REQ period
665 * Params : period - time (ns) for REQ
666 * Returns : table index
667 * Copyright: Copyright (c) 1996 John Shifflett, GeoLog Consulting
668 */
669static inline
670int round_period(unsigned int period)
671{
672 int i;
673
674 for (i = 1; sync_xfer_table[i].period_ns; i++) {
675 if ((period <= sync_xfer_table[i].period_ns) &&
676 (period > sync_xfer_table[i - 1].period_ns))
677 return i;
678 }
679 return 7;
680}
681
682/*
683 * Prototype: unsigned char calc_sync_xfer(unsigned int period, unsigned int offset)
684 * Purpose : calculate value for 33c93s SYNC register
685 * Params : period - time (ns) for REQ
686 * offset - offset in bytes between REQ/ACK
687 * Returns : value for SYNC register
688 * Copyright: Copyright (c) 1996 John Shifflett, GeoLog Consulting
689 */
690static
691unsigned char calc_sync_xfer(unsigned int period, unsigned int offset)
692{
693 return sync_xfer_table[round_period(period)].reg_value |
694 ((offset < SDTR_SIZE) ? offset : SDTR_SIZE);
695}
696
697/* ====================================================================================
698 * Command functions
699 */
700/*
701 * Function: acornscsi_kick(AS_Host *host)
702 * Purpose : kick next command to interface
703 * Params : host - host to send command to
704 * Returns : INTR_IDLE if idle, otherwise INTR_PROCESSING
705 * Notes : interrupts are always disabled!
706 */
707static
708intr_ret_t acornscsi_kick(AS_Host *host)
709{
710 int from_queue = 0;
Henneee0ca6b2006-10-01 13:18:37 +0200711 struct scsi_cmnd *SCpnt;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700712
713 /* first check to see if a command is waiting to be executed */
714 SCpnt = host->origSCpnt;
715 host->origSCpnt = NULL;
716
717 /* retrieve next command */
718 if (!SCpnt) {
719 SCpnt = queue_remove_exclude(&host->queues.issue, host->busyluns);
720 if (!SCpnt)
721 return INTR_IDLE;
722
723 from_queue = 1;
724 }
725
726 if (host->scsi.disconnectable && host->SCpnt) {
727 queue_add_cmd_tail(&host->queues.disconnected, host->SCpnt);
728 host->scsi.disconnectable = 0;
729#if (DEBUG & (DEBUG_QUEUES|DEBUG_DISCON))
730 DBG(host->SCpnt, printk("scsi%d.%c: moved command to disconnected queue\n",
731 host->host->host_no, acornscsi_target(host)));
732#endif
733 host->SCpnt = NULL;
734 }
735
736 /*
737 * If we have an interrupt pending, then we may have been reselected.
738 * In this case, we don't want to write to the registers
739 */
Russell Kingffd78582008-04-19 14:26:18 +0100740 if (!(sbic_arm_read(host, SBIC_ASR) & (ASR_INT|ASR_BSY|ASR_CIP))) {
741 sbic_arm_write(host, SBIC_DESTID, SCpnt->device->id);
742 sbic_arm_write(host, SBIC_CMND, CMND_SELWITHATN);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700743 }
744
745 /*
746 * claim host busy - all of these must happen atomically wrt
747 * our interrupt routine. Failure means command loss.
748 */
749 host->scsi.phase = PHASE_CONNECTING;
750 host->SCpnt = SCpnt;
751 host->scsi.SCp = SCpnt->SCp;
752 host->dma.xfer_setup = 0;
753 host->dma.xfer_required = 0;
754 host->dma.xfer_done = 0;
755
756#if (DEBUG & (DEBUG_ABORT|DEBUG_CONNECT))
757 DBG(SCpnt,printk("scsi%d.%c: starting cmd %02X\n",
758 host->host->host_no, '0' + SCpnt->device->id,
759 SCpnt->cmnd[0]));
760#endif
761
762 if (from_queue) {
763#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
764 /*
765 * tagged queueing - allocate a new tag to this command
766 */
767 if (SCpnt->device->simple_tags) {
768 SCpnt->device->current_tag += 1;
769 if (SCpnt->device->current_tag == 0)
770 SCpnt->device->current_tag = 1;
771 SCpnt->tag = SCpnt->device->current_tag;
772 } else
773#endif
774 set_bit(SCpnt->device->id * 8 + SCpnt->device->lun, host->busyluns);
775
776 host->stats.removes += 1;
777
778 switch (acornscsi_cmdtype(SCpnt->cmnd[0])) {
779 case CMD_WRITE:
780 host->stats.writes += 1;
781 break;
782 case CMD_READ:
783 host->stats.reads += 1;
784 break;
785 case CMD_MISC:
786 host->stats.miscs += 1;
787 break;
788 }
789 }
790
791 return INTR_PROCESSING;
792}
793
794/*
Henneee0ca6b2006-10-01 13:18:37 +0200795 * Function: void acornscsi_done(AS_Host *host, struct scsi_cmnd **SCpntp, unsigned int result)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700796 * Purpose : complete processing for command
797 * Params : host - interface that completed
798 * result - driver byte of result
799 */
Henneee0ca6b2006-10-01 13:18:37 +0200800static void acornscsi_done(AS_Host *host, struct scsi_cmnd **SCpntp,
801 unsigned int result)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700802{
Henneee0ca6b2006-10-01 13:18:37 +0200803 struct scsi_cmnd *SCpnt = *SCpntp;
Linus Torvalds1da177e2005-04-16 15:20:36 -0700804
805 /* clean up */
Russell Kingffd78582008-04-19 14:26:18 +0100806 sbic_arm_write(host, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700807
808 host->stats.fins += 1;
809
810 if (SCpnt) {
811 *SCpntp = NULL;
812
813 acornscsi_dma_cleanup(host);
814
815 SCpnt->result = result << 16 | host->scsi.SCp.Message << 8 | host->scsi.SCp.Status;
816
817 /*
818 * In theory, this should not happen. In practice, it seems to.
819 * Only trigger an error if the device attempts to report all happy
820 * but with untransferred buffers... If we don't do something, then
821 * data loss will occur. Should we check SCpnt->underflow here?
822 * It doesn't appear to be set to something meaningful by the higher
823 * levels all the time.
824 */
825 if (result == DID_OK) {
826 int xfer_warn = 0;
827
828 if (SCpnt->underflow == 0) {
829 if (host->scsi.SCp.ptr &&
830 acornscsi_cmdtype(SCpnt->cmnd[0]) != CMD_MISC)
831 xfer_warn = 1;
832 } else {
833 if (host->scsi.SCp.scsi_xferred < SCpnt->underflow ||
834 host->scsi.SCp.scsi_xferred != host->dma.transferred)
835 xfer_warn = 1;
836 }
837
838 /* ANSI standard says: (SCSI-2 Rev 10c Sect 5.6.6)
839 * Targets which break data transfers into multiple
840 * connections shall end each successful connection
841 * (except possibly the last) with a SAVE DATA
842 * POINTER - DISCONNECT message sequence.
843 *
844 * This makes it difficult to ensure that a transfer has
845 * completed. If we reach the end of a transfer during
846 * the command, then we can only have finished the transfer.
847 * therefore, if we seem to have some data remaining, this
848 * is not a problem.
849 */
850 if (host->dma.xfer_done)
851 xfer_warn = 0;
852
853 if (xfer_warn) {
854 switch (status_byte(SCpnt->result)) {
855 case CHECK_CONDITION:
856 case COMMAND_TERMINATED:
857 case BUSY:
858 case QUEUE_FULL:
859 case RESERVATION_CONFLICT:
860 break;
861
862 default:
863 printk(KERN_ERR "scsi%d.H: incomplete data transfer detected: result=%08X command=",
864 host->host->host_no, SCpnt->result);
db9dff32005-04-03 14:53:59 -0500865 __scsi_print_command(SCpnt->cmnd);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700866 acornscsi_dumpdma(host, "done");
867 acornscsi_dumplog(host, SCpnt->device->id);
868 SCpnt->result &= 0xffff;
869 SCpnt->result |= DID_ERROR << 16;
870 }
871 }
872 }
873
874 if (!SCpnt->scsi_done)
875 panic("scsi%d.H: null scsi_done function in acornscsi_done", host->host->host_no);
876
877 clear_bit(SCpnt->device->id * 8 + SCpnt->device->lun, host->busyluns);
878
879 SCpnt->scsi_done(SCpnt);
880 } else
881 printk("scsi%d: null command in acornscsi_done", host->host->host_no);
882
883 host->scsi.phase = PHASE_IDLE;
884}
885
886/* ====================================================================================
887 * DMA routines
888 */
889/*
890 * Purpose : update SCSI Data Pointer
891 * Notes : this will only be one SG entry or less
892 */
893static
Christoph Hellwig0a041372005-10-31 18:31:56 +0100894void acornscsi_data_updateptr(AS_Host *host, struct scsi_pointer *SCp, unsigned int length)
Linus Torvalds1da177e2005-04-16 15:20:36 -0700895{
896 SCp->ptr += length;
897 SCp->this_residual -= length;
898
899 if (SCp->this_residual == 0 && next_SCp(SCp) == 0)
900 host->dma.xfer_done = 1;
901}
902
903/*
904 * Prototype: void acornscsi_data_read(AS_Host *host, char *ptr,
905 * unsigned int start_addr, unsigned int length)
906 * Purpose : read data from DMA RAM
907 * Params : host - host to transfer from
908 * ptr - DRAM address
909 * start_addr - host mem address
910 * length - number of bytes to transfer
911 * Notes : this will only be one SG entry or less
912 */
913static
914void acornscsi_data_read(AS_Host *host, char *ptr,
915 unsigned int start_addr, unsigned int length)
916{
Russell Kinge95a1b62008-04-19 15:42:57 +0100917 extern void __acornscsi_in(void __iomem *, char *buf, int len);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700918 unsigned int page, offset, len = length;
919
920 page = (start_addr >> 12);
921 offset = start_addr & ((1 << 12) - 1);
922
Russell Kinge95a1b62008-04-19 15:42:57 +0100923 writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700924
925 while (len > 0) {
926 unsigned int this_len;
927
928 if (len + offset > (1 << 12))
929 this_len = (1 << 12) - offset;
930 else
931 this_len = len;
932
Russell Kinge95a1b62008-04-19 15:42:57 +0100933 __acornscsi_in(host->base + (offset << 1), ptr, this_len);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700934
935 offset += this_len;
936 ptr += this_len;
937 len -= this_len;
938
939 if (offset == (1 << 12)) {
940 offset = 0;
941 page ++;
Russell Kinge95a1b62008-04-19 15:42:57 +0100942 writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700943 }
944 }
Russell Kinge95a1b62008-04-19 15:42:57 +0100945 writeb(host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700946}
947
948/*
949 * Prototype: void acornscsi_data_write(AS_Host *host, char *ptr,
950 * unsigned int start_addr, unsigned int length)
951 * Purpose : write data to DMA RAM
952 * Params : host - host to transfer from
953 * ptr - DRAM address
954 * start_addr - host mem address
955 * length - number of bytes to transfer
956 * Notes : this will only be one SG entry or less
957 */
958static
959void acornscsi_data_write(AS_Host *host, char *ptr,
960 unsigned int start_addr, unsigned int length)
961{
Russell Kinge95a1b62008-04-19 15:42:57 +0100962 extern void __acornscsi_out(void __iomem *, char *buf, int len);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700963 unsigned int page, offset, len = length;
964
965 page = (start_addr >> 12);
966 offset = start_addr & ((1 << 12) - 1);
967
Russell Kinge95a1b62008-04-19 15:42:57 +0100968 writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700969
970 while (len > 0) {
971 unsigned int this_len;
972
973 if (len + offset > (1 << 12))
974 this_len = (1 << 12) - offset;
975 else
976 this_len = len;
977
Russell Kinge95a1b62008-04-19 15:42:57 +0100978 __acornscsi_out(host->base + (offset << 1), ptr, this_len);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700979
980 offset += this_len;
981 ptr += this_len;
982 len -= this_len;
983
984 if (offset == (1 << 12)) {
985 offset = 0;
986 page ++;
Russell Kinge95a1b62008-04-19 15:42:57 +0100987 writeb((page & 0x3f) | host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700988 }
989 }
Russell Kinge95a1b62008-04-19 15:42:57 +0100990 writeb(host->card.page_reg, host->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -0700991}
992
993/* =========================================================================================
994 * On-board DMA routines
995 */
996#ifdef USE_DMAC
997/*
998 * Prototype: void acornscsi_dmastop(AS_Host *host)
999 * Purpose : stop all DMA
1000 * Params : host - host on which to stop DMA
1001 * Notes : This is called when leaving DATA IN/OUT phase,
1002 * or when interface is RESET
1003 */
1004static inline
1005void acornscsi_dma_stop(AS_Host *host)
1006{
Russell Kingffd78582008-04-19 14:26:18 +01001007 dmac_write(host, DMAC_MASKREG, MASK_ON);
1008 dmac_clearintr(host);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001009
1010#if (DEBUG & DEBUG_DMA)
1011 DBG(host->SCpnt, acornscsi_dumpdma(host, "stop"));
1012#endif
1013}
1014
1015/*
1016 * Function: void acornscsi_dma_setup(AS_Host *host, dmadir_t direction)
1017 * Purpose : setup DMA controller for data transfer
1018 * Params : host - host to setup
1019 * direction - data transfer direction
1020 * Notes : This is called when entering DATA I/O phase, not
1021 * while we're in a DATA I/O phase
1022 */
1023static
1024void acornscsi_dma_setup(AS_Host *host, dmadir_t direction)
1025{
1026 unsigned int address, length, mode;
1027
1028 host->dma.direction = direction;
1029
Russell Kingffd78582008-04-19 14:26:18 +01001030 dmac_write(host, DMAC_MASKREG, MASK_ON);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001031
1032 if (direction == DMA_OUT) {
1033#if (DEBUG & DEBUG_NO_WRITE)
1034 if (NO_WRITE & (1 << host->SCpnt->device->id)) {
1035 printk(KERN_CRIT "scsi%d.%c: I can't handle DMA_OUT!\n",
1036 host->host->host_no, acornscsi_target(host));
1037 return;
1038 }
1039#endif
1040 mode = DMAC_WRITE;
1041 } else
1042 mode = DMAC_READ;
1043
1044 /*
1045 * Allocate some buffer space, limited to half the buffer size
1046 */
1047 length = min_t(unsigned int, host->scsi.SCp.this_residual, DMAC_BUFFER_SIZE / 2);
1048 if (length) {
1049 host->dma.start_addr = address = host->dma.free_addr;
1050 host->dma.free_addr = (host->dma.free_addr + length) &
1051 (DMAC_BUFFER_SIZE - 1);
1052
1053 /*
1054 * Transfer data to DMA memory
1055 */
1056 if (direction == DMA_OUT)
1057 acornscsi_data_write(host, host->scsi.SCp.ptr, host->dma.start_addr,
1058 length);
1059
1060 length -= 1;
Russell Kingffd78582008-04-19 14:26:18 +01001061 dmac_write(host, DMAC_TXCNTLO, length);
1062 dmac_write(host, DMAC_TXCNTHI, length >> 8);
1063 dmac_write(host, DMAC_TXADRLO, address);
1064 dmac_write(host, DMAC_TXADRMD, address >> 8);
1065 dmac_write(host, DMAC_TXADRHI, 0);
1066 dmac_write(host, DMAC_MODECON, mode);
1067 dmac_write(host, DMAC_MASKREG, MASK_OFF);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001068
1069#if (DEBUG & DEBUG_DMA)
1070 DBG(host->SCpnt, acornscsi_dumpdma(host, "strt"));
1071#endif
1072 host->dma.xfer_setup = 1;
1073 }
1074}
1075
1076/*
1077 * Function: void acornscsi_dma_cleanup(AS_Host *host)
1078 * Purpose : ensure that all DMA transfers are up-to-date & host->scsi.SCp is correct
1079 * Params : host - host to finish
1080 * Notes : This is called when a command is:
1081 * terminating, RESTORE_POINTERS, SAVE_POINTERS, DISCONECT
1082 * : This must not return until all transfers are completed.
1083 */
1084static
1085void acornscsi_dma_cleanup(AS_Host *host)
1086{
Russell Kingffd78582008-04-19 14:26:18 +01001087 dmac_write(host, DMAC_MASKREG, MASK_ON);
1088 dmac_clearintr(host);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001089
1090 /*
1091 * Check for a pending transfer
1092 */
1093 if (host->dma.xfer_required) {
1094 host->dma.xfer_required = 0;
1095 if (host->dma.direction == DMA_IN)
1096 acornscsi_data_read(host, host->dma.xfer_ptr,
1097 host->dma.xfer_start, host->dma.xfer_length);
1098 }
1099
1100 /*
1101 * Has a transfer been setup?
1102 */
1103 if (host->dma.xfer_setup) {
1104 unsigned int transferred;
1105
1106 host->dma.xfer_setup = 0;
1107
1108#if (DEBUG & DEBUG_DMA)
1109 DBG(host->SCpnt, acornscsi_dumpdma(host, "cupi"));
1110#endif
1111
1112 /*
1113 * Calculate number of bytes transferred from DMA.
1114 */
Russell Kingffd78582008-04-19 14:26:18 +01001115 transferred = dmac_address(host) - host->dma.start_addr;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001116 host->dma.transferred += transferred;
1117
1118 if (host->dma.direction == DMA_IN)
1119 acornscsi_data_read(host, host->scsi.SCp.ptr,
1120 host->dma.start_addr, transferred);
1121
1122 /*
1123 * Update SCSI pointers
1124 */
1125 acornscsi_data_updateptr(host, &host->scsi.SCp, transferred);
1126#if (DEBUG & DEBUG_DMA)
1127 DBG(host->SCpnt, acornscsi_dumpdma(host, "cupo"));
1128#endif
1129 }
1130}
1131
1132/*
1133 * Function: void acornscsi_dmacintr(AS_Host *host)
1134 * Purpose : handle interrupts from DMAC device
1135 * Params : host - host to process
1136 * Notes : If reading, we schedule the read to main memory &
1137 * allow the transfer to continue.
1138 * : If writing, we fill the onboard DMA memory from main
1139 * memory.
1140 * : Called whenever DMAC finished it's current transfer.
1141 */
1142static
1143void acornscsi_dma_intr(AS_Host *host)
1144{
1145 unsigned int address, length, transferred;
1146
1147#if (DEBUG & DEBUG_DMA)
1148 DBG(host->SCpnt, acornscsi_dumpdma(host, "inti"));
1149#endif
1150
Russell Kingffd78582008-04-19 14:26:18 +01001151 dmac_write(host, DMAC_MASKREG, MASK_ON);
1152 dmac_clearintr(host);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001153
1154 /*
1155 * Calculate amount transferred via DMA
1156 */
Russell Kingffd78582008-04-19 14:26:18 +01001157 transferred = dmac_address(host) - host->dma.start_addr;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001158 host->dma.transferred += transferred;
1159
1160 /*
1161 * Schedule DMA transfer off board
1162 */
1163 if (host->dma.direction == DMA_IN) {
1164 host->dma.xfer_start = host->dma.start_addr;
1165 host->dma.xfer_length = transferred;
1166 host->dma.xfer_ptr = host->scsi.SCp.ptr;
1167 host->dma.xfer_required = 1;
1168 }
1169
1170 acornscsi_data_updateptr(host, &host->scsi.SCp, transferred);
1171
1172 /*
1173 * Allocate some buffer space, limited to half the on-board RAM size
1174 */
1175 length = min_t(unsigned int, host->scsi.SCp.this_residual, DMAC_BUFFER_SIZE / 2);
1176 if (length) {
1177 host->dma.start_addr = address = host->dma.free_addr;
1178 host->dma.free_addr = (host->dma.free_addr + length) &
1179 (DMAC_BUFFER_SIZE - 1);
1180
1181 /*
1182 * Transfer data to DMA memory
1183 */
1184 if (host->dma.direction == DMA_OUT)
1185 acornscsi_data_write(host, host->scsi.SCp.ptr, host->dma.start_addr,
1186 length);
1187
1188 length -= 1;
Russell Kingffd78582008-04-19 14:26:18 +01001189 dmac_write(host, DMAC_TXCNTLO, length);
1190 dmac_write(host, DMAC_TXCNTHI, length >> 8);
1191 dmac_write(host, DMAC_TXADRLO, address);
1192 dmac_write(host, DMAC_TXADRMD, address >> 8);
1193 dmac_write(host, DMAC_TXADRHI, 0);
1194 dmac_write(host, DMAC_MASKREG, MASK_OFF);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001195
1196#if (DEBUG & DEBUG_DMA)
1197 DBG(host->SCpnt, acornscsi_dumpdma(host, "into"));
1198#endif
1199 } else {
1200 host->dma.xfer_setup = 0;
1201#if 0
1202 /*
1203 * If the interface still wants more, then this is an error.
1204 * We give it another byte, but we also attempt to raise an
1205 * attention condition. We continue giving one byte until
1206 * the device recognises the attention.
1207 */
Russell Kingffd78582008-04-19 14:26:18 +01001208 if (dmac_read(host, DMAC_STATUS) & STATUS_RQ0) {
Linus Torvalds1da177e2005-04-16 15:20:36 -07001209 acornscsi_abortcmd(host, host->SCpnt->tag);
1210
Russell Kingffd78582008-04-19 14:26:18 +01001211 dmac_write(host, DMAC_TXCNTLO, 0);
1212 dmac_write(host, DMAC_TXCNTHI, 0);
1213 dmac_write(host, DMAC_TXADRLO, 0);
1214 dmac_write(host, DMAC_TXADRMD, 0);
1215 dmac_write(host, DMAC_TXADRHI, 0);
1216 dmac_write(host, DMAC_MASKREG, MASK_OFF);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001217 }
1218#endif
1219 }
1220}
1221
1222/*
1223 * Function: void acornscsi_dma_xfer(AS_Host *host)
1224 * Purpose : transfer data between AcornSCSI and memory
1225 * Params : host - host to process
1226 */
1227static
1228void acornscsi_dma_xfer(AS_Host *host)
1229{
1230 host->dma.xfer_required = 0;
1231
1232 if (host->dma.direction == DMA_IN)
1233 acornscsi_data_read(host, host->dma.xfer_ptr,
1234 host->dma.xfer_start, host->dma.xfer_length);
1235}
1236
1237/*
1238 * Function: void acornscsi_dma_adjust(AS_Host *host)
1239 * Purpose : adjust DMA pointers & count for bytes transferred to
1240 * SBIC but not SCSI bus.
1241 * Params : host - host to adjust DMA count for
1242 */
1243static
1244void acornscsi_dma_adjust(AS_Host *host)
1245{
1246 if (host->dma.xfer_setup) {
1247 signed long transferred;
1248#if (DEBUG & (DEBUG_DMA|DEBUG_WRITE))
1249 DBG(host->SCpnt, acornscsi_dumpdma(host, "adji"));
1250#endif
1251 /*
1252 * Calculate correct DMA address - DMA is ahead of SCSI bus while
1253 * writing.
1254 * host->scsi.SCp.scsi_xferred is the number of bytes
1255 * actually transferred to/from the SCSI bus.
1256 * host->dma.transferred is the number of bytes transferred
1257 * over DMA since host->dma.start_addr was last set.
1258 *
1259 * real_dma_addr = host->dma.start_addr + host->scsi.SCp.scsi_xferred
1260 * - host->dma.transferred
1261 */
1262 transferred = host->scsi.SCp.scsi_xferred - host->dma.transferred;
1263 if (transferred < 0)
1264 printk("scsi%d.%c: Ack! DMA write correction %ld < 0!\n",
1265 host->host->host_no, acornscsi_target(host), transferred);
1266 else if (transferred == 0)
1267 host->dma.xfer_setup = 0;
1268 else {
1269 transferred += host->dma.start_addr;
Russell Kingffd78582008-04-19 14:26:18 +01001270 dmac_write(host, DMAC_TXADRLO, transferred);
1271 dmac_write(host, DMAC_TXADRMD, transferred >> 8);
1272 dmac_write(host, DMAC_TXADRHI, transferred >> 16);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001273#if (DEBUG & (DEBUG_DMA|DEBUG_WRITE))
1274 DBG(host->SCpnt, acornscsi_dumpdma(host, "adjo"));
1275#endif
1276 }
1277 }
1278}
1279#endif
1280
1281/* =========================================================================================
1282 * Data I/O
1283 */
1284static int
1285acornscsi_write_pio(AS_Host *host, char *bytes, int *ptr, int len, unsigned int max_timeout)
1286{
1287 unsigned int asr, timeout = max_timeout;
1288 int my_ptr = *ptr;
1289
1290 while (my_ptr < len) {
Russell Kingffd78582008-04-19 14:26:18 +01001291 asr = sbic_arm_read(host, SBIC_ASR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001292
1293 if (asr & ASR_DBR) {
1294 timeout = max_timeout;
1295
Russell Kingffd78582008-04-19 14:26:18 +01001296 sbic_arm_write(host, SBIC_DATA, bytes[my_ptr++]);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001297 } else if (asr & ASR_INT)
1298 break;
1299 else if (--timeout == 0)
1300 break;
1301 udelay(1);
1302 }
1303
1304 *ptr = my_ptr;
1305
1306 return (timeout == 0) ? -1 : 0;
1307}
1308
1309/*
1310 * Function: void acornscsi_sendcommand(AS_Host *host)
1311 * Purpose : send a command to a target
1312 * Params : host - host which is connected to target
1313 */
1314static void
1315acornscsi_sendcommand(AS_Host *host)
1316{
Henneee0ca6b2006-10-01 13:18:37 +02001317 struct scsi_cmnd *SCpnt = host->SCpnt;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001318
Russell Kingffd78582008-04-19 14:26:18 +01001319 sbic_arm_write(host, SBIC_TRANSCNTH, 0);
1320 sbic_arm_writenext(host, 0);
1321 sbic_arm_writenext(host, SCpnt->cmd_len - host->scsi.SCp.sent_command);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001322
1323 acornscsi_sbic_issuecmd(host, CMND_XFERINFO);
1324
1325 if (acornscsi_write_pio(host, SCpnt->cmnd,
1326 (int *)&host->scsi.SCp.sent_command, SCpnt->cmd_len, 1000000))
1327 printk("scsi%d: timeout while sending command\n", host->host->host_no);
1328
1329 host->scsi.phase = PHASE_COMMAND;
1330}
1331
1332static
1333void acornscsi_sendmessage(AS_Host *host)
1334{
1335 unsigned int message_length = msgqueue_msglength(&host->scsi.msgs);
1336 unsigned int msgnr;
1337 struct message *msg;
1338
1339#if (DEBUG & DEBUG_MESSAGES)
1340 printk("scsi%d.%c: sending message ",
1341 host->host->host_no, acornscsi_target(host));
1342#endif
1343
1344 switch (message_length) {
1345 case 0:
1346 acornscsi_sbic_issuecmd(host, CMND_XFERINFO | CMND_SBT);
1347
1348 acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "sending message 1");
1349
Russell Kingffd78582008-04-19 14:26:18 +01001350 sbic_arm_write(host, SBIC_DATA, NOP);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001351
1352 host->scsi.last_message = NOP;
1353#if (DEBUG & DEBUG_MESSAGES)
1354 printk("NOP");
1355#endif
1356 break;
1357
1358 case 1:
1359 acornscsi_sbic_issuecmd(host, CMND_XFERINFO | CMND_SBT);
1360 msg = msgqueue_getmsg(&host->scsi.msgs, 0);
1361
1362 acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "sending message 2");
1363
Russell Kingffd78582008-04-19 14:26:18 +01001364 sbic_arm_write(host, SBIC_DATA, msg->msg[0]);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001365
1366 host->scsi.last_message = msg->msg[0];
1367#if (DEBUG & DEBUG_MESSAGES)
Matthew Wilcox1abfd372005-12-15 16:22:01 -05001368 spi_print_msg(msg->msg);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001369#endif
1370 break;
1371
1372 default:
1373 /*
1374 * ANSI standard says: (SCSI-2 Rev 10c Sect 5.6.14)
1375 * 'When a target sends this (MESSAGE_REJECT) message, it
1376 * shall change to MESSAGE IN phase and send this message
1377 * prior to requesting additional message bytes from the
1378 * initiator. This provides an interlock so that the
1379 * initiator can determine which message byte is rejected.
1380 */
Russell Kingffd78582008-04-19 14:26:18 +01001381 sbic_arm_write(host, SBIC_TRANSCNTH, 0);
1382 sbic_arm_writenext(host, 0);
1383 sbic_arm_writenext(host, message_length);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001384 acornscsi_sbic_issuecmd(host, CMND_XFERINFO);
1385
1386 msgnr = 0;
1387 while ((msg = msgqueue_getmsg(&host->scsi.msgs, msgnr++)) != NULL) {
1388 unsigned int i;
1389#if (DEBUG & DEBUG_MESSAGES)
Matthew Wilcox1abfd372005-12-15 16:22:01 -05001390 spi_print_msg(msg);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001391#endif
1392 i = 0;
1393 if (acornscsi_write_pio(host, msg->msg, &i, msg->length, 1000000))
1394 printk("scsi%d: timeout while sending message\n", host->host->host_no);
1395
1396 host->scsi.last_message = msg->msg[0];
1397 if (msg->msg[0] == EXTENDED_MESSAGE)
1398 host->scsi.last_message |= msg->msg[2] << 8;
1399
1400 if (i != msg->length)
1401 break;
1402 }
1403 break;
1404 }
1405#if (DEBUG & DEBUG_MESSAGES)
1406 printk("\n");
1407#endif
1408}
1409
1410/*
1411 * Function: void acornscsi_readstatusbyte(AS_Host *host)
1412 * Purpose : Read status byte from connected target
1413 * Params : host - host connected to target
1414 */
1415static
1416void acornscsi_readstatusbyte(AS_Host *host)
1417{
1418 acornscsi_sbic_issuecmd(host, CMND_XFERINFO|CMND_SBT);
1419 acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "reading status byte");
Russell Kingffd78582008-04-19 14:26:18 +01001420 host->scsi.SCp.Status = sbic_arm_read(host, SBIC_DATA);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001421}
1422
1423/*
1424 * Function: unsigned char acornscsi_readmessagebyte(AS_Host *host)
1425 * Purpose : Read one message byte from connected target
1426 * Params : host - host connected to target
1427 */
1428static
1429unsigned char acornscsi_readmessagebyte(AS_Host *host)
1430{
1431 unsigned char message;
1432
1433 acornscsi_sbic_issuecmd(host, CMND_XFERINFO | CMND_SBT);
1434
1435 acornscsi_sbic_wait(host, ASR_DBR, ASR_DBR, 1000, "for message byte");
1436
Russell Kingffd78582008-04-19 14:26:18 +01001437 message = sbic_arm_read(host, SBIC_DATA);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001438
1439 /* wait for MSGIN-XFER-PAUSED */
1440 acornscsi_sbic_wait(host, ASR_INT, ASR_INT, 1000, "for interrupt after message byte");
1441
Russell Kingffd78582008-04-19 14:26:18 +01001442 sbic_arm_read(host, SBIC_SSR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001443
1444 return message;
1445}
1446
1447/*
1448 * Function: void acornscsi_message(AS_Host *host)
1449 * Purpose : Read complete message from connected target & action message
1450 * Params : host - host connected to target
1451 */
1452static
1453void acornscsi_message(AS_Host *host)
1454{
1455 unsigned char message[16];
1456 unsigned int msgidx = 0, msglen = 1;
1457
1458 do {
1459 message[msgidx] = acornscsi_readmessagebyte(host);
1460
1461 switch (msgidx) {
1462 case 0:
1463 if (message[0] == EXTENDED_MESSAGE ||
1464 (message[0] >= 0x20 && message[0] <= 0x2f))
1465 msglen = 2;
1466 break;
1467
1468 case 1:
1469 if (message[0] == EXTENDED_MESSAGE)
1470 msglen += message[msgidx];
1471 break;
1472 }
1473 msgidx += 1;
1474 if (msgidx < msglen) {
1475 acornscsi_sbic_issuecmd(host, CMND_NEGATEACK);
1476
1477 /* wait for next msg-in */
1478 acornscsi_sbic_wait(host, ASR_INT, ASR_INT, 1000, "for interrupt after negate ack");
Russell Kingffd78582008-04-19 14:26:18 +01001479 sbic_arm_read(host, SBIC_SSR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001480 }
1481 } while (msgidx < msglen);
1482
1483#if (DEBUG & DEBUG_MESSAGES)
1484 printk("scsi%d.%c: message in: ",
1485 host->host->host_no, acornscsi_target(host));
Matthew Wilcox1abfd372005-12-15 16:22:01 -05001486 spi_print_msg(message);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001487 printk("\n");
1488#endif
1489
1490 if (host->scsi.phase == PHASE_RECONNECTED) {
1491 /*
1492 * ANSI standard says: (Section SCSI-2 Rev. 10c Sect 5.6.17)
1493 * 'Whenever a target reconnects to an initiator to continue
1494 * a tagged I/O process, the SIMPLE QUEUE TAG message shall
1495 * be sent immediately following the IDENTIFY message...'
1496 */
1497 if (message[0] == SIMPLE_QUEUE_TAG)
1498 host->scsi.reconnected.tag = message[1];
1499 if (acornscsi_reconnect_finish(host))
1500 host->scsi.phase = PHASE_MSGIN;
1501 }
1502
1503 switch (message[0]) {
1504 case ABORT:
1505 case ABORT_TAG:
1506 case COMMAND_COMPLETE:
1507 if (host->scsi.phase != PHASE_STATUSIN) {
1508 printk(KERN_ERR "scsi%d.%c: command complete following non-status in phase?\n",
1509 host->host->host_no, acornscsi_target(host));
1510 acornscsi_dumplog(host, host->SCpnt->device->id);
1511 }
1512 host->scsi.phase = PHASE_DONE;
1513 host->scsi.SCp.Message = message[0];
1514 break;
1515
1516 case SAVE_POINTERS:
1517 /*
1518 * ANSI standard says: (Section SCSI-2 Rev. 10c Sect 5.6.20)
1519 * 'The SAVE DATA POINTER message is sent from a target to
1520 * direct the initiator to copy the active data pointer to
1521 * the saved data pointer for the current I/O process.
1522 */
1523 acornscsi_dma_cleanup(host);
1524 host->SCpnt->SCp = host->scsi.SCp;
1525 host->SCpnt->SCp.sent_command = 0;
1526 host->scsi.phase = PHASE_MSGIN;
1527 break;
1528
1529 case RESTORE_POINTERS:
1530 /*
1531 * ANSI standard says: (Section SCSI-2 Rev. 10c Sect 5.6.19)
1532 * 'The RESTORE POINTERS message is sent from a target to
1533 * direct the initiator to copy the most recently saved
1534 * command, data, and status pointers for the I/O process
1535 * to the corresponding active pointers. The command and
1536 * status pointers shall be restored to the beginning of
1537 * the present command and status areas.'
1538 */
1539 acornscsi_dma_cleanup(host);
1540 host->scsi.SCp = host->SCpnt->SCp;
1541 host->scsi.phase = PHASE_MSGIN;
1542 break;
1543
1544 case DISCONNECT:
1545 /*
1546 * ANSI standard says: (Section SCSI-2 Rev. 10c Sect 6.4.2)
1547 * 'On those occasions when an error or exception condition occurs
1548 * and the target elects to repeat the information transfer, the
1549 * target may repeat the transfer either issuing a RESTORE POINTERS
1550 * message or by disconnecting without issuing a SAVE POINTERS
1551 * message. When reconnection is completed, the most recent
1552 * saved pointer values are restored.'
1553 */
1554 acornscsi_dma_cleanup(host);
1555 host->scsi.phase = PHASE_DISCONNECT;
1556 break;
1557
1558 case MESSAGE_REJECT:
1559#if 0 /* this isn't needed any more */
1560 /*
1561 * If we were negociating sync transfer, we don't yet know if
1562 * this REJECT is for the sync transfer or for the tagged queue/wide
Lucas De Marchi25985ed2011-03-30 22:57:33 -03001563 * transfer. Re-initiate sync transfer negotiation now, and if
Linus Torvalds1da177e2005-04-16 15:20:36 -07001564 * we got a REJECT in response to SDTR, then it'll be set to DONE.
1565 */
1566 if (host->device[host->SCpnt->device->id].sync_state == SYNC_SENT_REQUEST)
1567 host->device[host->SCpnt->device->id].sync_state = SYNC_NEGOCIATE;
1568#endif
1569
1570 /*
1571 * If we have any messages waiting to go out, then assert ATN now
1572 */
1573 if (msgqueue_msglength(&host->scsi.msgs))
1574 acornscsi_sbic_issuecmd(host, CMND_ASSERTATN);
1575
1576 switch (host->scsi.last_message) {
1577#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
1578 case HEAD_OF_QUEUE_TAG:
1579 case ORDERED_QUEUE_TAG:
1580 case SIMPLE_QUEUE_TAG:
1581 /*
1582 * ANSI standard says: (Section SCSI-2 Rev. 10c Sect 5.6.17)
1583 * If a target does not implement tagged queuing and a queue tag
1584 * message is received, it shall respond with a MESSAGE REJECT
1585 * message and accept the I/O process as if it were untagged.
1586 */
1587 printk(KERN_NOTICE "scsi%d.%c: disabling tagged queueing\n",
1588 host->host->host_no, acornscsi_target(host));
1589 host->SCpnt->device->simple_tags = 0;
1590 set_bit(host->SCpnt->device->id * 8 + host->SCpnt->device->lun, host->busyluns);
1591 break;
1592#endif
1593 case EXTENDED_MESSAGE | (EXTENDED_SDTR << 8):
1594 /*
1595 * Target can't handle synchronous transfers
1596 */
1597 printk(KERN_NOTICE "scsi%d.%c: Using asynchronous transfer\n",
1598 host->host->host_no, acornscsi_target(host));
1599 host->device[host->SCpnt->device->id].sync_xfer = SYNCHTRANSFER_2DBA;
1600 host->device[host->SCpnt->device->id].sync_state = SYNC_ASYNCHRONOUS;
Russell Kingffd78582008-04-19 14:26:18 +01001601 sbic_arm_write(host, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001602 break;
1603
1604 default:
1605 break;
1606 }
1607 break;
1608
1609 case QUEUE_FULL:
1610 /* TODO: target queue is full */
1611 break;
1612
1613 case SIMPLE_QUEUE_TAG:
1614 /* tag queue reconnect... message[1] = queue tag. Print something to indicate something happened! */
1615 printk("scsi%d.%c: reconnect queue tag %02X\n",
1616 host->host->host_no, acornscsi_target(host),
1617 message[1]);
1618 break;
1619
1620 case EXTENDED_MESSAGE:
1621 switch (message[2]) {
1622#ifdef CONFIG_SCSI_ACORNSCSI_SYNC
1623 case EXTENDED_SDTR:
1624 if (host->device[host->SCpnt->device->id].sync_state == SYNC_SENT_REQUEST) {
1625 /*
1626 * We requested synchronous transfers. This isn't quite right...
1627 * We can only say if this succeeded if we proceed on to execute the
1628 * command from this message. If we get a MESSAGE PARITY ERROR,
1629 * and the target retries fail, then we fallback to asynchronous mode
1630 */
1631 host->device[host->SCpnt->device->id].sync_state = SYNC_COMPLETED;
1632 printk(KERN_NOTICE "scsi%d.%c: Using synchronous transfer, offset %d, %d ns\n",
1633 host->host->host_no, acornscsi_target(host),
1634 message[4], message[3] * 4);
1635 host->device[host->SCpnt->device->id].sync_xfer =
1636 calc_sync_xfer(message[3] * 4, message[4]);
1637 } else {
1638 unsigned char period, length;
1639 /*
1640 * Target requested synchronous transfers. The agreement is only
1641 * to be in operation AFTER the target leaves message out phase.
1642 */
1643 acornscsi_sbic_issuecmd(host, CMND_ASSERTATN);
1644 period = max_t(unsigned int, message[3], sdtr_period / 4);
1645 length = min_t(unsigned int, message[4], sdtr_size);
1646 msgqueue_addmsg(&host->scsi.msgs, 5, EXTENDED_MESSAGE, 3,
1647 EXTENDED_SDTR, period, length);
1648 host->device[host->SCpnt->device->id].sync_xfer =
1649 calc_sync_xfer(period * 4, length);
1650 }
Russell Kingffd78582008-04-19 14:26:18 +01001651 sbic_arm_write(host, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001652 break;
1653#else
1654 /* We do not accept synchronous transfers. Respond with a
1655 * MESSAGE_REJECT.
1656 */
1657#endif
1658
1659 case EXTENDED_WDTR:
1660 /* The WD33C93A is only 8-bit. We respond with a MESSAGE_REJECT
1661 * to a wide data transfer request.
1662 */
1663 default:
1664 acornscsi_sbic_issuecmd(host, CMND_ASSERTATN);
1665 msgqueue_flush(&host->scsi.msgs);
1666 msgqueue_addmsg(&host->scsi.msgs, 1, MESSAGE_REJECT);
1667 break;
1668 }
1669 break;
1670
1671#ifdef CONFIG_SCSI_ACORNSCSI_LINK
1672 case LINKED_CMD_COMPLETE:
1673 case LINKED_FLG_CMD_COMPLETE:
1674 /*
1675 * We don't support linked commands yet
1676 */
1677 if (0) {
1678#if (DEBUG & DEBUG_LINK)
1679 printk("scsi%d.%c: lun %d tag %d linked command complete\n",
1680 host->host->host_no, acornscsi_target(host), host->SCpnt->tag);
1681#endif
1682 /*
1683 * A linked command should only terminate with one of these messages
1684 * if there are more linked commands available.
1685 */
1686 if (!host->SCpnt->next_link) {
1687 printk(KERN_WARNING "scsi%d.%c: lun %d tag %d linked command complete, but no next_link\n",
1688 instance->host_no, acornscsi_target(host), host->SCpnt->tag);
1689 acornscsi_sbic_issuecmd(host, CMND_ASSERTATN);
1690 msgqueue_addmsg(&host->scsi.msgs, 1, ABORT);
1691 } else {
Henneee0ca6b2006-10-01 13:18:37 +02001692 struct scsi_cmnd *SCpnt = host->SCpnt;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001693
1694 acornscsi_dma_cleanup(host);
1695
1696 host->SCpnt = host->SCpnt->next_link;
1697 host->SCpnt->tag = SCpnt->tag;
1698 SCpnt->result = DID_OK | host->scsi.SCp.Message << 8 | host->Scsi.SCp.Status;
1699 SCpnt->done(SCpnt);
1700
1701 /* initialise host->SCpnt->SCp */
1702 }
1703 break;
1704 }
1705#endif
1706
1707 default: /* reject message */
1708 printk(KERN_ERR "scsi%d.%c: unrecognised message %02X, rejecting\n",
1709 host->host->host_no, acornscsi_target(host),
1710 message[0]);
1711 acornscsi_sbic_issuecmd(host, CMND_ASSERTATN);
1712 msgqueue_flush(&host->scsi.msgs);
1713 msgqueue_addmsg(&host->scsi.msgs, 1, MESSAGE_REJECT);
1714 host->scsi.phase = PHASE_MSGIN;
1715 break;
1716 }
1717 acornscsi_sbic_issuecmd(host, CMND_NEGATEACK);
1718}
1719
1720/*
1721 * Function: int acornscsi_buildmessages(AS_Host *host)
1722 * Purpose : build the connection messages for a host
1723 * Params : host - host to add messages to
1724 */
1725static
1726void acornscsi_buildmessages(AS_Host *host)
1727{
1728#if 0
1729 /* does the device need resetting? */
1730 if (cmd_reset) {
1731 msgqueue_addmsg(&host->scsi.msgs, 1, BUS_DEVICE_RESET);
1732 return;
1733 }
1734#endif
1735
1736 msgqueue_addmsg(&host->scsi.msgs, 1,
1737 IDENTIFY(host->device[host->SCpnt->device->id].disconnect_ok,
1738 host->SCpnt->device->lun));
1739
1740#if 0
1741 /* does the device need the current command aborted */
1742 if (cmd_aborted) {
1743 acornscsi_abortcmd(host->SCpnt->tag);
1744 return;
1745 }
1746#endif
1747
1748#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
1749 if (host->SCpnt->tag) {
1750 unsigned int tag_type;
1751
1752 if (host->SCpnt->cmnd[0] == REQUEST_SENSE ||
1753 host->SCpnt->cmnd[0] == TEST_UNIT_READY ||
1754 host->SCpnt->cmnd[0] == INQUIRY)
1755 tag_type = HEAD_OF_QUEUE_TAG;
1756 else
1757 tag_type = SIMPLE_QUEUE_TAG;
1758 msgqueue_addmsg(&host->scsi.msgs, 2, tag_type, host->SCpnt->tag);
1759 }
1760#endif
1761
1762#ifdef CONFIG_SCSI_ACORNSCSI_SYNC
1763 if (host->device[host->SCpnt->device->id].sync_state == SYNC_NEGOCIATE) {
1764 host->device[host->SCpnt->device->id].sync_state = SYNC_SENT_REQUEST;
1765 msgqueue_addmsg(&host->scsi.msgs, 5,
1766 EXTENDED_MESSAGE, 3, EXTENDED_SDTR,
1767 sdtr_period / 4, sdtr_size);
1768 }
1769#endif
1770}
1771
1772/*
1773 * Function: int acornscsi_starttransfer(AS_Host *host)
1774 * Purpose : transfer data to/from connected target
1775 * Params : host - host to which target is connected
1776 * Returns : 0 if failure
1777 */
1778static
1779int acornscsi_starttransfer(AS_Host *host)
1780{
1781 int residual;
1782
1783 if (!host->scsi.SCp.ptr /*&& host->scsi.SCp.this_residual*/) {
1784 printk(KERN_ERR "scsi%d.%c: null buffer passed to acornscsi_starttransfer\n",
1785 host->host->host_no, acornscsi_target(host));
1786 return 0;
1787 }
1788
Boaz Harrosh84ac86c2007-09-09 21:31:21 +03001789 residual = scsi_bufflen(host->SCpnt) - host->scsi.SCp.scsi_xferred;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001790
Russell Kingffd78582008-04-19 14:26:18 +01001791 sbic_arm_write(host, SBIC_SYNCHTRANSFER, host->device[host->SCpnt->device->id].sync_xfer);
1792 sbic_arm_writenext(host, residual >> 16);
1793 sbic_arm_writenext(host, residual >> 8);
1794 sbic_arm_writenext(host, residual);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001795 acornscsi_sbic_issuecmd(host, CMND_XFERINFO);
1796 return 1;
1797}
1798
1799/* =========================================================================================
1800 * Connection & Disconnection
1801 */
1802/*
1803 * Function : acornscsi_reconnect(AS_Host *host)
1804 * Purpose : reconnect a previously disconnected command
1805 * Params : host - host specific data
1806 * Remarks : SCSI spec says:
1807 * 'The set of active pointers is restored from the set
1808 * of saved pointers upon reconnection of the I/O process'
1809 */
1810static
1811int acornscsi_reconnect(AS_Host *host)
1812{
1813 unsigned int target, lun, ok = 0;
1814
Russell Kingffd78582008-04-19 14:26:18 +01001815 target = sbic_arm_read(host, SBIC_SOURCEID);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001816
1817 if (!(target & 8))
1818 printk(KERN_ERR "scsi%d: invalid source id after reselection "
1819 "- device fault?\n",
1820 host->host->host_no);
1821
1822 target &= 7;
1823
1824 if (host->SCpnt && !host->scsi.disconnectable) {
1825 printk(KERN_ERR "scsi%d.%d: reconnected while command in "
1826 "progress to target %d?\n",
1827 host->host->host_no, target, host->SCpnt->device->id);
1828 host->SCpnt = NULL;
1829 }
1830
Russell Kingffd78582008-04-19 14:26:18 +01001831 lun = sbic_arm_read(host, SBIC_DATA) & 7;
Linus Torvalds1da177e2005-04-16 15:20:36 -07001832
1833 host->scsi.reconnected.target = target;
1834 host->scsi.reconnected.lun = lun;
1835 host->scsi.reconnected.tag = 0;
1836
1837 if (host->scsi.disconnectable && host->SCpnt &&
1838 host->SCpnt->device->id == target && host->SCpnt->device->lun == lun)
1839 ok = 1;
1840
1841 if (!ok && queue_probetgtlun(&host->queues.disconnected, target, lun))
1842 ok = 1;
1843
1844 ADD_STATUS(target, 0x81, host->scsi.phase, 0);
1845
1846 if (ok) {
1847 host->scsi.phase = PHASE_RECONNECTED;
1848 } else {
1849 /* this doesn't seem to work */
1850 printk(KERN_ERR "scsi%d.%c: reselected with no command "
1851 "to reconnect with\n",
1852 host->host->host_no, '0' + target);
1853 acornscsi_dumplog(host, target);
1854 acornscsi_abortcmd(host, 0);
1855 if (host->SCpnt) {
1856 queue_add_cmd_tail(&host->queues.disconnected, host->SCpnt);
1857 host->SCpnt = NULL;
1858 }
1859 }
1860 acornscsi_sbic_issuecmd(host, CMND_NEGATEACK);
1861 return !ok;
1862}
1863
1864/*
1865 * Function: int acornscsi_reconect_finish(AS_Host *host)
1866 * Purpose : finish reconnecting a command
1867 * Params : host - host to complete
1868 * Returns : 0 if failed
1869 */
1870static
1871int acornscsi_reconnect_finish(AS_Host *host)
1872{
1873 if (host->scsi.disconnectable && host->SCpnt) {
1874 host->scsi.disconnectable = 0;
1875 if (host->SCpnt->device->id == host->scsi.reconnected.target &&
1876 host->SCpnt->device->lun == host->scsi.reconnected.lun &&
1877 host->SCpnt->tag == host->scsi.reconnected.tag) {
1878#if (DEBUG & (DEBUG_QUEUES|DEBUG_DISCON))
1879 DBG(host->SCpnt, printk("scsi%d.%c: reconnected",
1880 host->host->host_no, acornscsi_target(host)));
1881#endif
1882 } else {
1883 queue_add_cmd_tail(&host->queues.disconnected, host->SCpnt);
1884#if (DEBUG & (DEBUG_QUEUES|DEBUG_DISCON))
1885 DBG(host->SCpnt, printk("scsi%d.%c: had to move command "
1886 "to disconnected queue\n",
1887 host->host->host_no, acornscsi_target(host)));
1888#endif
1889 host->SCpnt = NULL;
1890 }
1891 }
1892 if (!host->SCpnt) {
1893 host->SCpnt = queue_remove_tgtluntag(&host->queues.disconnected,
1894 host->scsi.reconnected.target,
1895 host->scsi.reconnected.lun,
1896 host->scsi.reconnected.tag);
1897#if (DEBUG & (DEBUG_QUEUES|DEBUG_DISCON))
1898 DBG(host->SCpnt, printk("scsi%d.%c: had to get command",
1899 host->host->host_no, acornscsi_target(host)));
1900#endif
1901 }
1902
1903 if (!host->SCpnt)
1904 acornscsi_abortcmd(host, host->scsi.reconnected.tag);
1905 else {
1906 /*
1907 * Restore data pointer from SAVED pointers.
1908 */
1909 host->scsi.SCp = host->SCpnt->SCp;
1910#if (DEBUG & (DEBUG_QUEUES|DEBUG_DISCON))
1911 printk(", data pointers: [%p, %X]",
1912 host->scsi.SCp.ptr, host->scsi.SCp.this_residual);
1913#endif
1914 }
1915#if (DEBUG & (DEBUG_QUEUES|DEBUG_DISCON))
1916 printk("\n");
1917#endif
1918
1919 host->dma.transferred = host->scsi.SCp.scsi_xferred;
1920
1921 return host->SCpnt != NULL;
1922}
1923
1924/*
1925 * Function: void acornscsi_disconnect_unexpected(AS_Host *host)
1926 * Purpose : handle an unexpected disconnect
1927 * Params : host - host on which disconnect occurred
1928 */
1929static
1930void acornscsi_disconnect_unexpected(AS_Host *host)
1931{
1932 printk(KERN_ERR "scsi%d.%c: unexpected disconnect\n",
1933 host->host->host_no, acornscsi_target(host));
1934#if (DEBUG & DEBUG_ABORT)
1935 acornscsi_dumplog(host, 8);
1936#endif
1937
1938 acornscsi_done(host, &host->SCpnt, DID_ERROR);
1939}
1940
1941/*
1942 * Function: void acornscsi_abortcmd(AS_host *host, unsigned char tag)
1943 * Purpose : abort a currently executing command
1944 * Params : host - host with connected command to abort
1945 * tag - tag to abort
1946 */
1947static
1948void acornscsi_abortcmd(AS_Host *host, unsigned char tag)
1949{
1950 host->scsi.phase = PHASE_ABORTED;
Russell Kingffd78582008-04-19 14:26:18 +01001951 sbic_arm_write(host, SBIC_CMND, CMND_ASSERTATN);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001952
1953 msgqueue_flush(&host->scsi.msgs);
1954#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
1955 if (tag)
1956 msgqueue_addmsg(&host->scsi.msgs, 2, ABORT_TAG, tag);
1957 else
1958#endif
1959 msgqueue_addmsg(&host->scsi.msgs, 1, ABORT);
1960}
1961
1962/* ==========================================================================================
1963 * Interrupt routines.
1964 */
1965/*
1966 * Function: int acornscsi_sbicintr(AS_Host *host)
1967 * Purpose : handle interrupts from SCSI device
1968 * Params : host - host to process
1969 * Returns : INTR_PROCESS if expecting another SBIC interrupt
1970 * INTR_IDLE if no interrupt
1971 * INTR_NEXT_COMMAND if we have finished processing the command
1972 */
1973static
1974intr_ret_t acornscsi_sbicintr(AS_Host *host, int in_irq)
1975{
1976 unsigned int asr, ssr;
1977
Russell Kingffd78582008-04-19 14:26:18 +01001978 asr = sbic_arm_read(host, SBIC_ASR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001979 if (!(asr & ASR_INT))
1980 return INTR_IDLE;
1981
Russell Kingffd78582008-04-19 14:26:18 +01001982 ssr = sbic_arm_read(host, SBIC_SSR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07001983
1984#if (DEBUG & DEBUG_PHASES)
1985 print_sbic_status(asr, ssr, host->scsi.phase);
1986#endif
1987
1988 ADD_STATUS(8, ssr, host->scsi.phase, in_irq);
1989
1990 if (host->SCpnt && !host->scsi.disconnectable)
1991 ADD_STATUS(host->SCpnt->device->id, ssr, host->scsi.phase, in_irq);
1992
1993 switch (ssr) {
1994 case 0x00: /* reset state - not advanced */
1995 printk(KERN_ERR "scsi%d: reset in standard mode but wanted advanced mode.\n",
1996 host->host->host_no);
1997 /* setup sbic - WD33C93A */
Russell Kingffd78582008-04-19 14:26:18 +01001998 sbic_arm_write(host, SBIC_OWNID, OWNID_EAF | host->host->this_id);
1999 sbic_arm_write(host, SBIC_CMND, CMND_RESET);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002000 return INTR_IDLE;
2001
2002 case 0x01: /* reset state - advanced */
Russell Kingffd78582008-04-19 14:26:18 +01002003 sbic_arm_write(host, SBIC_CTRL, INIT_SBICDMA | CTRL_IDI);
2004 sbic_arm_write(host, SBIC_TIMEOUT, TIMEOUT_TIME);
2005 sbic_arm_write(host, SBIC_SYNCHTRANSFER, SYNCHTRANSFER_2DBA);
2006 sbic_arm_write(host, SBIC_SOURCEID, SOURCEID_ER | SOURCEID_DSP);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002007 msgqueue_flush(&host->scsi.msgs);
2008 return INTR_IDLE;
2009
2010 case 0x41: /* unexpected disconnect aborted command */
2011 acornscsi_disconnect_unexpected(host);
2012 return INTR_NEXT_COMMAND;
2013 }
2014
2015 switch (host->scsi.phase) {
2016 case PHASE_CONNECTING: /* STATE: command removed from issue queue */
2017 switch (ssr) {
2018 case 0x11: /* -> PHASE_CONNECTED */
2019 /* BUS FREE -> SELECTION */
2020 host->scsi.phase = PHASE_CONNECTED;
2021 msgqueue_flush(&host->scsi.msgs);
2022 host->dma.transferred = host->scsi.SCp.scsi_xferred;
2023 /* 33C93 gives next interrupt indicating bus phase */
Russell Kingffd78582008-04-19 14:26:18 +01002024 asr = sbic_arm_read(host, SBIC_ASR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002025 if (!(asr & ASR_INT))
2026 break;
Russell Kingffd78582008-04-19 14:26:18 +01002027 ssr = sbic_arm_read(host, SBIC_SSR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002028 ADD_STATUS(8, ssr, host->scsi.phase, 1);
2029 ADD_STATUS(host->SCpnt->device->id, ssr, host->scsi.phase, 1);
2030 goto connected;
2031
2032 case 0x42: /* select timed out */
2033 /* -> PHASE_IDLE */
2034 acornscsi_done(host, &host->SCpnt, DID_NO_CONNECT);
2035 return INTR_NEXT_COMMAND;
2036
2037 case 0x81: /* -> PHASE_RECONNECTED or PHASE_ABORTED */
2038 /* BUS FREE -> RESELECTION */
2039 host->origSCpnt = host->SCpnt;
2040 host->SCpnt = NULL;
2041 msgqueue_flush(&host->scsi.msgs);
2042 acornscsi_reconnect(host);
2043 break;
2044
2045 default:
2046 printk(KERN_ERR "scsi%d.%c: PHASE_CONNECTING, SSR %02X?\n",
2047 host->host->host_no, acornscsi_target(host), ssr);
2048 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2049 acornscsi_abortcmd(host, host->SCpnt->tag);
2050 }
2051 return INTR_PROCESSING;
2052
2053 connected:
2054 case PHASE_CONNECTED: /* STATE: device selected ok */
2055 switch (ssr) {
2056#ifdef NONSTANDARD
2057 case 0x8a: /* -> PHASE_COMMAND, PHASE_COMMANDPAUSED */
2058 /* SELECTION -> COMMAND */
2059 acornscsi_sendcommand(host);
2060 break;
2061
2062 case 0x8b: /* -> PHASE_STATUS */
2063 /* SELECTION -> STATUS */
2064 acornscsi_readstatusbyte(host);
2065 host->scsi.phase = PHASE_STATUSIN;
2066 break;
2067#endif
2068
2069 case 0x8e: /* -> PHASE_MSGOUT */
2070 /* SELECTION ->MESSAGE OUT */
2071 host->scsi.phase = PHASE_MSGOUT;
2072 acornscsi_buildmessages(host);
2073 acornscsi_sendmessage(host);
2074 break;
2075
2076 /* these should not happen */
2077 case 0x85: /* target disconnected */
2078 acornscsi_done(host, &host->SCpnt, DID_ERROR);
2079 break;
2080
2081 default:
2082 printk(KERN_ERR "scsi%d.%c: PHASE_CONNECTED, SSR %02X?\n",
2083 host->host->host_no, acornscsi_target(host), ssr);
2084 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2085 acornscsi_abortcmd(host, host->SCpnt->tag);
2086 }
2087 return INTR_PROCESSING;
2088
2089 case PHASE_MSGOUT: /* STATE: connected & sent IDENTIFY message */
2090 /*
2091 * SCSI standard says that MESSAGE OUT phases can be followed by a
2092 * DATA phase, STATUS phase, MESSAGE IN phase or COMMAND phase
2093 */
2094 switch (ssr) {
2095 case 0x8a: /* -> PHASE_COMMAND, PHASE_COMMANDPAUSED */
2096 case 0x1a: /* -> PHASE_COMMAND, PHASE_COMMANDPAUSED */
2097 /* MESSAGE OUT -> COMMAND */
2098 acornscsi_sendcommand(host);
2099 break;
2100
2101 case 0x8b: /* -> PHASE_STATUS */
2102 case 0x1b: /* -> PHASE_STATUS */
2103 /* MESSAGE OUT -> STATUS */
2104 acornscsi_readstatusbyte(host);
2105 host->scsi.phase = PHASE_STATUSIN;
2106 break;
2107
2108 case 0x8e: /* -> PHASE_MSGOUT */
2109 /* MESSAGE_OUT(MESSAGE_IN) ->MESSAGE OUT */
2110 acornscsi_sendmessage(host);
2111 break;
2112
2113 case 0x4f: /* -> PHASE_MSGIN, PHASE_DISCONNECT */
2114 case 0x1f: /* -> PHASE_MSGIN, PHASE_DISCONNECT */
2115 /* MESSAGE OUT -> MESSAGE IN */
2116 acornscsi_message(host);
2117 break;
2118
2119 default:
2120 printk(KERN_ERR "scsi%d.%c: PHASE_MSGOUT, SSR %02X?\n",
2121 host->host->host_no, acornscsi_target(host), ssr);
2122 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2123 }
2124 return INTR_PROCESSING;
2125
2126 case PHASE_COMMAND: /* STATE: connected & command sent */
2127 switch (ssr) {
2128 case 0x18: /* -> PHASE_DATAOUT */
2129 /* COMMAND -> DATA OUT */
2130 if (host->scsi.SCp.sent_command != host->SCpnt->cmd_len)
2131 acornscsi_abortcmd(host, host->SCpnt->tag);
2132 acornscsi_dma_setup(host, DMA_OUT);
2133 if (!acornscsi_starttransfer(host))
2134 acornscsi_abortcmd(host, host->SCpnt->tag);
2135 host->scsi.phase = PHASE_DATAOUT;
2136 return INTR_IDLE;
2137
2138 case 0x19: /* -> PHASE_DATAIN */
2139 /* COMMAND -> DATA IN */
2140 if (host->scsi.SCp.sent_command != host->SCpnt->cmd_len)
2141 acornscsi_abortcmd(host, host->SCpnt->tag);
2142 acornscsi_dma_setup(host, DMA_IN);
2143 if (!acornscsi_starttransfer(host))
2144 acornscsi_abortcmd(host, host->SCpnt->tag);
2145 host->scsi.phase = PHASE_DATAIN;
2146 return INTR_IDLE;
2147
2148 case 0x1b: /* -> PHASE_STATUS */
2149 /* COMMAND -> STATUS */
2150 acornscsi_readstatusbyte(host);
2151 host->scsi.phase = PHASE_STATUSIN;
2152 break;
2153
2154 case 0x1e: /* -> PHASE_MSGOUT */
2155 /* COMMAND -> MESSAGE OUT */
2156 acornscsi_sendmessage(host);
2157 break;
2158
2159 case 0x1f: /* -> PHASE_MSGIN, PHASE_DISCONNECT */
2160 /* COMMAND -> MESSAGE IN */
2161 acornscsi_message(host);
2162 break;
2163
2164 default:
2165 printk(KERN_ERR "scsi%d.%c: PHASE_COMMAND, SSR %02X?\n",
2166 host->host->host_no, acornscsi_target(host), ssr);
2167 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2168 }
2169 return INTR_PROCESSING;
2170
2171 case PHASE_DISCONNECT: /* STATE: connected, received DISCONNECT msg */
2172 if (ssr == 0x85) { /* -> PHASE_IDLE */
2173 host->scsi.disconnectable = 1;
2174 host->scsi.reconnected.tag = 0;
2175 host->scsi.phase = PHASE_IDLE;
2176 host->stats.disconnects += 1;
2177 } else {
2178 printk(KERN_ERR "scsi%d.%c: PHASE_DISCONNECT, SSR %02X instead of disconnect?\n",
2179 host->host->host_no, acornscsi_target(host), ssr);
2180 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2181 }
2182 return INTR_NEXT_COMMAND;
2183
2184 case PHASE_IDLE: /* STATE: disconnected */
2185 if (ssr == 0x81) /* -> PHASE_RECONNECTED or PHASE_ABORTED */
2186 acornscsi_reconnect(host);
2187 else {
2188 printk(KERN_ERR "scsi%d.%c: PHASE_IDLE, SSR %02X while idle?\n",
2189 host->host->host_no, acornscsi_target(host), ssr);
2190 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2191 }
2192 return INTR_PROCESSING;
2193
2194 case PHASE_RECONNECTED: /* STATE: device reconnected to initiator */
2195 /*
2196 * Command reconnected - if MESGIN, get message - it may be
2197 * the tag. If not, get command out of disconnected queue
2198 */
2199 /*
2200 * If we reconnected and we're not in MESSAGE IN phase after IDENTIFY,
2201 * reconnect I_T_L command
2202 */
2203 if (ssr != 0x8f && !acornscsi_reconnect_finish(host))
2204 return INTR_IDLE;
2205 ADD_STATUS(host->SCpnt->device->id, ssr, host->scsi.phase, in_irq);
2206 switch (ssr) {
2207 case 0x88: /* data out phase */
2208 /* -> PHASE_DATAOUT */
2209 /* MESSAGE IN -> DATA OUT */
2210 acornscsi_dma_setup(host, DMA_OUT);
2211 if (!acornscsi_starttransfer(host))
2212 acornscsi_abortcmd(host, host->SCpnt->tag);
2213 host->scsi.phase = PHASE_DATAOUT;
2214 return INTR_IDLE;
2215
2216 case 0x89: /* data in phase */
2217 /* -> PHASE_DATAIN */
2218 /* MESSAGE IN -> DATA IN */
2219 acornscsi_dma_setup(host, DMA_IN);
2220 if (!acornscsi_starttransfer(host))
2221 acornscsi_abortcmd(host, host->SCpnt->tag);
2222 host->scsi.phase = PHASE_DATAIN;
2223 return INTR_IDLE;
2224
2225 case 0x8a: /* command out */
2226 /* MESSAGE IN -> COMMAND */
2227 acornscsi_sendcommand(host);/* -> PHASE_COMMAND, PHASE_COMMANDPAUSED */
2228 break;
2229
2230 case 0x8b: /* status in */
2231 /* -> PHASE_STATUSIN */
2232 /* MESSAGE IN -> STATUS */
2233 acornscsi_readstatusbyte(host);
2234 host->scsi.phase = PHASE_STATUSIN;
2235 break;
2236
2237 case 0x8e: /* message out */
2238 /* -> PHASE_MSGOUT */
2239 /* MESSAGE IN -> MESSAGE OUT */
2240 acornscsi_sendmessage(host);
2241 break;
2242
2243 case 0x8f: /* message in */
2244 acornscsi_message(host); /* -> PHASE_MSGIN, PHASE_DISCONNECT */
2245 break;
2246
2247 default:
2248 printk(KERN_ERR "scsi%d.%c: PHASE_RECONNECTED, SSR %02X after reconnect?\n",
2249 host->host->host_no, acornscsi_target(host), ssr);
2250 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2251 }
2252 return INTR_PROCESSING;
2253
2254 case PHASE_DATAIN: /* STATE: transferred data in */
2255 /*
2256 * This is simple - if we disconnect then the DMA address & count is
2257 * correct.
2258 */
2259 switch (ssr) {
2260 case 0x19: /* -> PHASE_DATAIN */
2261 case 0x89: /* -> PHASE_DATAIN */
2262 acornscsi_abortcmd(host, host->SCpnt->tag);
2263 return INTR_IDLE;
2264
2265 case 0x1b: /* -> PHASE_STATUSIN */
2266 case 0x4b: /* -> PHASE_STATUSIN */
2267 case 0x8b: /* -> PHASE_STATUSIN */
2268 /* DATA IN -> STATUS */
Boaz Harrosh84ac86c2007-09-09 21:31:21 +03002269 host->scsi.SCp.scsi_xferred = scsi_bufflen(host->SCpnt) -
Linus Torvalds1da177e2005-04-16 15:20:36 -07002270 acornscsi_sbic_xfcount(host);
2271 acornscsi_dma_stop(host);
2272 acornscsi_readstatusbyte(host);
2273 host->scsi.phase = PHASE_STATUSIN;
2274 break;
2275
2276 case 0x1e: /* -> PHASE_MSGOUT */
2277 case 0x4e: /* -> PHASE_MSGOUT */
2278 case 0x8e: /* -> PHASE_MSGOUT */
2279 /* DATA IN -> MESSAGE OUT */
Boaz Harrosh84ac86c2007-09-09 21:31:21 +03002280 host->scsi.SCp.scsi_xferred = scsi_bufflen(host->SCpnt) -
Linus Torvalds1da177e2005-04-16 15:20:36 -07002281 acornscsi_sbic_xfcount(host);
2282 acornscsi_dma_stop(host);
2283 acornscsi_sendmessage(host);
2284 break;
2285
2286 case 0x1f: /* message in */
2287 case 0x4f: /* message in */
2288 case 0x8f: /* message in */
2289 /* DATA IN -> MESSAGE IN */
Boaz Harrosh84ac86c2007-09-09 21:31:21 +03002290 host->scsi.SCp.scsi_xferred = scsi_bufflen(host->SCpnt) -
Linus Torvalds1da177e2005-04-16 15:20:36 -07002291 acornscsi_sbic_xfcount(host);
2292 acornscsi_dma_stop(host);
2293 acornscsi_message(host); /* -> PHASE_MSGIN, PHASE_DISCONNECT */
2294 break;
2295
2296 default:
2297 printk(KERN_ERR "scsi%d.%c: PHASE_DATAIN, SSR %02X?\n",
2298 host->host->host_no, acornscsi_target(host), ssr);
2299 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2300 }
2301 return INTR_PROCESSING;
2302
2303 case PHASE_DATAOUT: /* STATE: transferred data out */
2304 /*
2305 * This is more complicated - if we disconnect, the DMA could be 12
2306 * bytes ahead of us. We need to correct this.
2307 */
2308 switch (ssr) {
2309 case 0x18: /* -> PHASE_DATAOUT */
2310 case 0x88: /* -> PHASE_DATAOUT */
2311 acornscsi_abortcmd(host, host->SCpnt->tag);
2312 return INTR_IDLE;
2313
2314 case 0x1b: /* -> PHASE_STATUSIN */
2315 case 0x4b: /* -> PHASE_STATUSIN */
2316 case 0x8b: /* -> PHASE_STATUSIN */
2317 /* DATA OUT -> STATUS */
Boaz Harrosh84ac86c2007-09-09 21:31:21 +03002318 host->scsi.SCp.scsi_xferred = scsi_bufflen(host->SCpnt) -
Linus Torvalds1da177e2005-04-16 15:20:36 -07002319 acornscsi_sbic_xfcount(host);
2320 acornscsi_dma_stop(host);
2321 acornscsi_dma_adjust(host);
2322 acornscsi_readstatusbyte(host);
2323 host->scsi.phase = PHASE_STATUSIN;
2324 break;
2325
2326 case 0x1e: /* -> PHASE_MSGOUT */
2327 case 0x4e: /* -> PHASE_MSGOUT */
2328 case 0x8e: /* -> PHASE_MSGOUT */
2329 /* DATA OUT -> MESSAGE OUT */
Boaz Harrosh84ac86c2007-09-09 21:31:21 +03002330 host->scsi.SCp.scsi_xferred = scsi_bufflen(host->SCpnt) -
Linus Torvalds1da177e2005-04-16 15:20:36 -07002331 acornscsi_sbic_xfcount(host);
2332 acornscsi_dma_stop(host);
2333 acornscsi_dma_adjust(host);
2334 acornscsi_sendmessage(host);
2335 break;
2336
2337 case 0x1f: /* message in */
2338 case 0x4f: /* message in */
2339 case 0x8f: /* message in */
2340 /* DATA OUT -> MESSAGE IN */
Boaz Harrosh84ac86c2007-09-09 21:31:21 +03002341 host->scsi.SCp.scsi_xferred = scsi_bufflen(host->SCpnt) -
Linus Torvalds1da177e2005-04-16 15:20:36 -07002342 acornscsi_sbic_xfcount(host);
2343 acornscsi_dma_stop(host);
2344 acornscsi_dma_adjust(host);
2345 acornscsi_message(host); /* -> PHASE_MSGIN, PHASE_DISCONNECT */
2346 break;
2347
2348 default:
2349 printk(KERN_ERR "scsi%d.%c: PHASE_DATAOUT, SSR %02X?\n",
2350 host->host->host_no, acornscsi_target(host), ssr);
2351 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2352 }
2353 return INTR_PROCESSING;
2354
2355 case PHASE_STATUSIN: /* STATE: status in complete */
2356 switch (ssr) {
2357 case 0x1f: /* -> PHASE_MSGIN, PHASE_DONE, PHASE_DISCONNECT */
2358 case 0x8f: /* -> PHASE_MSGIN, PHASE_DONE, PHASE_DISCONNECT */
2359 /* STATUS -> MESSAGE IN */
2360 acornscsi_message(host);
2361 break;
2362
2363 case 0x1e: /* -> PHASE_MSGOUT */
2364 case 0x8e: /* -> PHASE_MSGOUT */
2365 /* STATUS -> MESSAGE OUT */
2366 acornscsi_sendmessage(host);
2367 break;
2368
2369 default:
2370 printk(KERN_ERR "scsi%d.%c: PHASE_STATUSIN, SSR %02X instead of MESSAGE_IN?\n",
2371 host->host->host_no, acornscsi_target(host), ssr);
2372 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2373 }
2374 return INTR_PROCESSING;
2375
2376 case PHASE_MSGIN: /* STATE: message in */
2377 switch (ssr) {
2378 case 0x1e: /* -> PHASE_MSGOUT */
2379 case 0x4e: /* -> PHASE_MSGOUT */
2380 case 0x8e: /* -> PHASE_MSGOUT */
2381 /* MESSAGE IN -> MESSAGE OUT */
2382 acornscsi_sendmessage(host);
2383 break;
2384
2385 case 0x1f: /* -> PHASE_MSGIN, PHASE_DONE, PHASE_DISCONNECT */
2386 case 0x2f:
2387 case 0x4f:
2388 case 0x8f:
2389 acornscsi_message(host);
2390 break;
2391
2392 case 0x85:
2393 printk("scsi%d.%c: strange message in disconnection\n",
2394 host->host->host_no, acornscsi_target(host));
2395 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2396 acornscsi_done(host, &host->SCpnt, DID_ERROR);
2397 break;
2398
2399 default:
2400 printk(KERN_ERR "scsi%d.%c: PHASE_MSGIN, SSR %02X after message in?\n",
2401 host->host->host_no, acornscsi_target(host), ssr);
2402 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2403 }
2404 return INTR_PROCESSING;
2405
2406 case PHASE_DONE: /* STATE: received status & message */
2407 switch (ssr) {
2408 case 0x85: /* -> PHASE_IDLE */
2409 acornscsi_done(host, &host->SCpnt, DID_OK);
2410 return INTR_NEXT_COMMAND;
2411
2412 case 0x1e:
2413 case 0x8e:
2414 acornscsi_sendmessage(host);
2415 break;
2416
2417 default:
2418 printk(KERN_ERR "scsi%d.%c: PHASE_DONE, SSR %02X instead of disconnect?\n",
2419 host->host->host_no, acornscsi_target(host), ssr);
2420 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2421 }
2422 return INTR_PROCESSING;
2423
2424 case PHASE_ABORTED:
2425 switch (ssr) {
2426 case 0x85:
2427 if (host->SCpnt)
2428 acornscsi_done(host, &host->SCpnt, DID_ABORT);
2429 else {
2430 clear_bit(host->scsi.reconnected.target * 8 + host->scsi.reconnected.lun,
2431 host->busyluns);
2432 host->scsi.phase = PHASE_IDLE;
2433 }
2434 return INTR_NEXT_COMMAND;
2435
2436 case 0x1e:
2437 case 0x2e:
2438 case 0x4e:
2439 case 0x8e:
2440 acornscsi_sendmessage(host);
2441 break;
2442
2443 default:
2444 printk(KERN_ERR "scsi%d.%c: PHASE_ABORTED, SSR %02X?\n",
2445 host->host->host_no, acornscsi_target(host), ssr);
2446 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2447 }
2448 return INTR_PROCESSING;
2449
2450 default:
2451 printk(KERN_ERR "scsi%d.%c: unknown driver phase %d\n",
2452 host->host->host_no, acornscsi_target(host), ssr);
2453 acornscsi_dumplog(host, host->SCpnt ? host->SCpnt->device->id : 8);
2454 }
2455 return INTR_PROCESSING;
2456}
2457
2458/*
David Howells7d12e782006-10-05 14:55:46 +01002459 * Prototype: void acornscsi_intr(int irq, void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002460 * Purpose : handle interrupts from Acorn SCSI card
2461 * Params : irq - interrupt number
2462 * dev_id - device specific data (AS_Host structure)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002463 */
2464static irqreturn_t
David Howells7d12e782006-10-05 14:55:46 +01002465acornscsi_intr(int irq, void *dev_id)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002466{
2467 AS_Host *host = (AS_Host *)dev_id;
2468 intr_ret_t ret;
2469 int iostatus;
2470 int in_irq = 0;
2471
2472 do {
2473 ret = INTR_IDLE;
2474
Russell Kinge95a1b62008-04-19 15:42:57 +01002475 iostatus = readb(host->fast + INT_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002476
2477 if (iostatus & 2) {
2478 acornscsi_dma_intr(host);
Russell Kinge95a1b62008-04-19 15:42:57 +01002479 iostatus = readb(host->fast + INT_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002480 }
2481
2482 if (iostatus & 8)
2483 ret = acornscsi_sbicintr(host, in_irq);
2484
2485 /*
2486 * If we have a transfer pending, start it.
2487 * Only start it if the interface has already started transferring
2488 * it's data
2489 */
2490 if (host->dma.xfer_required)
2491 acornscsi_dma_xfer(host);
2492
2493 if (ret == INTR_NEXT_COMMAND)
2494 ret = acornscsi_kick(host);
2495
2496 in_irq = 1;
2497 } while (ret != INTR_IDLE);
2498
2499 return IRQ_HANDLED;
2500}
2501
2502/*=============================================================================================
2503 * Interfaces between interrupt handler and rest of scsi code
2504 */
2505
2506/*
Henneee0ca6b2006-10-01 13:18:37 +02002507 * Function : acornscsi_queuecmd(struct scsi_cmnd *cmd, void (*done)(struct scsi_cmnd *))
Linus Torvalds1da177e2005-04-16 15:20:36 -07002508 * Purpose : queues a SCSI command
2509 * Params : cmd - SCSI command
2510 * done - function called on completion, with pointer to command descriptor
2511 * Returns : 0, or < 0 on error.
2512 */
Jeff Garzikf2812332010-11-16 02:10:29 -05002513static int acornscsi_queuecmd_lck(struct scsi_cmnd *SCpnt,
Henneee0ca6b2006-10-01 13:18:37 +02002514 void (*done)(struct scsi_cmnd *))
Linus Torvalds1da177e2005-04-16 15:20:36 -07002515{
2516 AS_Host *host = (AS_Host *)SCpnt->device->host->hostdata;
2517
2518 if (!done) {
2519 /* there should be some way of rejecting errors like this without panicing... */
2520 panic("scsi%d: queuecommand called with NULL done function [cmd=%p]",
2521 host->host->host_no, SCpnt);
2522 return -EINVAL;
2523 }
2524
2525#if (DEBUG & DEBUG_NO_WRITE)
2526 if (acornscsi_cmdtype(SCpnt->cmnd[0]) == CMD_WRITE && (NO_WRITE & (1 << SCpnt->device->id))) {
2527 printk(KERN_CRIT "scsi%d.%c: WRITE attempted with NO_WRITE flag set\n",
2528 host->host->host_no, '0' + SCpnt->device->id);
2529 SCpnt->result = DID_NO_CONNECT << 16;
2530 done(SCpnt);
2531 return 0;
2532 }
2533#endif
2534
2535 SCpnt->scsi_done = done;
2536 SCpnt->host_scribble = NULL;
2537 SCpnt->result = 0;
2538 SCpnt->tag = 0;
2539 SCpnt->SCp.phase = (int)acornscsi_datadirection(SCpnt->cmnd[0]);
2540 SCpnt->SCp.sent_command = 0;
2541 SCpnt->SCp.scsi_xferred = 0;
2542
2543 init_SCp(SCpnt);
2544
2545 host->stats.queues += 1;
2546
2547 {
2548 unsigned long flags;
2549
2550 if (!queue_add_cmd_ordered(&host->queues.issue, SCpnt)) {
2551 SCpnt->result = DID_ERROR << 16;
2552 done(SCpnt);
2553 return 0;
2554 }
2555 local_irq_save(flags);
2556 if (host->scsi.phase == PHASE_IDLE)
2557 acornscsi_kick(host);
2558 local_irq_restore(flags);
2559 }
2560 return 0;
2561}
2562
Jeff Garzikf2812332010-11-16 02:10:29 -05002563DEF_SCSI_QCMD(acornscsi_queuecmd)
2564
Linus Torvalds1da177e2005-04-16 15:20:36 -07002565/*
Henneee0ca6b2006-10-01 13:18:37 +02002566 * Prototype: void acornscsi_reportstatus(struct scsi_cmnd **SCpntp1, struct scsi_cmnd **SCpntp2, int result)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002567 * Purpose : pass a result to *SCpntp1, and check if *SCpntp1 = *SCpntp2
2568 * Params : SCpntp1 - pointer to command to return
2569 * SCpntp2 - pointer to command to check
2570 * result - result to pass back to mid-level done function
2571 * Returns : *SCpntp2 = NULL if *SCpntp1 is the same command structure as *SCpntp2.
2572 */
Henneee0ca6b2006-10-01 13:18:37 +02002573static inline void acornscsi_reportstatus(struct scsi_cmnd **SCpntp1,
2574 struct scsi_cmnd **SCpntp2,
2575 int result)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002576{
Henneee0ca6b2006-10-01 13:18:37 +02002577 struct scsi_cmnd *SCpnt = *SCpntp1;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002578
2579 if (SCpnt) {
2580 *SCpntp1 = NULL;
2581
2582 SCpnt->result = result;
2583 SCpnt->scsi_done(SCpnt);
2584 }
2585
2586 if (SCpnt == *SCpntp2)
2587 *SCpntp2 = NULL;
2588}
2589
2590enum res_abort { res_not_running, res_success, res_success_clear, res_snooze };
2591
2592/*
Henneee0ca6b2006-10-01 13:18:37 +02002593 * Prototype: enum res acornscsi_do_abort(struct scsi_cmnd *SCpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002594 * Purpose : abort a command on this host
2595 * Params : SCpnt - command to abort
2596 * Returns : our abort status
2597 */
Henneee0ca6b2006-10-01 13:18:37 +02002598static enum res_abort acornscsi_do_abort(AS_Host *host, struct scsi_cmnd *SCpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002599{
2600 enum res_abort res = res_not_running;
2601
2602 if (queue_remove_cmd(&host->queues.issue, SCpnt)) {
2603 /*
2604 * The command was on the issue queue, and has not been
2605 * issued yet. We can remove the command from the queue,
2606 * and acknowledge the abort. Neither the devices nor the
2607 * interface know about the command.
2608 */
2609//#if (DEBUG & DEBUG_ABORT)
2610 printk("on issue queue ");
2611//#endif
2612 res = res_success;
2613 } else if (queue_remove_cmd(&host->queues.disconnected, SCpnt)) {
2614 /*
2615 * The command was on the disconnected queue. Simply
2616 * acknowledge the abort condition, and when the target
2617 * reconnects, we will give it an ABORT message. The
2618 * target should then disconnect, and we will clear
2619 * the busylun bit.
2620 */
2621//#if (DEBUG & DEBUG_ABORT)
2622 printk("on disconnected queue ");
2623//#endif
2624 res = res_success;
2625 } else if (host->SCpnt == SCpnt) {
2626 unsigned long flags;
2627
2628//#if (DEBUG & DEBUG_ABORT)
2629 printk("executing ");
2630//#endif
2631
2632 local_irq_save(flags);
2633 switch (host->scsi.phase) {
2634 /*
2635 * If the interface is idle, and the command is 'disconnectable',
2636 * then it is the same as on the disconnected queue. We simply
2637 * remove all traces of the command. When the target reconnects,
2638 * we will give it an ABORT message since the command could not
2639 * be found. When the target finally disconnects, we will clear
2640 * the busylun bit.
2641 */
2642 case PHASE_IDLE:
2643 if (host->scsi.disconnectable) {
2644 host->scsi.disconnectable = 0;
2645 host->SCpnt = NULL;
2646 res = res_success;
2647 }
2648 break;
2649
2650 /*
2651 * If the command has connected and done nothing further,
2652 * simply force a disconnect. We also need to clear the
2653 * busylun bit.
2654 */
2655 case PHASE_CONNECTED:
Russell Kingffd78582008-04-19 14:26:18 +01002656 sbic_arm_write(host, SBIC_CMND, CMND_DISCONNECT);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002657 host->SCpnt = NULL;
2658 res = res_success_clear;
2659 break;
2660
2661 default:
2662 acornscsi_abortcmd(host, host->SCpnt->tag);
2663 res = res_snooze;
2664 }
2665 local_irq_restore(flags);
2666 } else if (host->origSCpnt == SCpnt) {
2667 /*
2668 * The command will be executed next, but a command
2669 * is currently using the interface. This is similar to
2670 * being on the issue queue, except the busylun bit has
2671 * been set.
2672 */
2673 host->origSCpnt = NULL;
2674//#if (DEBUG & DEBUG_ABORT)
2675 printk("waiting for execution ");
2676//#endif
2677 res = res_success_clear;
2678 } else
2679 printk("unknown ");
2680
2681 return res;
2682}
2683
2684/*
Henneee0ca6b2006-10-01 13:18:37 +02002685 * Prototype: int acornscsi_abort(struct scsi_cmnd *SCpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002686 * Purpose : abort a command on this host
2687 * Params : SCpnt - command to abort
2688 * Returns : one of SCSI_ABORT_ macros
2689 */
Henneee0ca6b2006-10-01 13:18:37 +02002690int acornscsi_abort(struct scsi_cmnd *SCpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002691{
2692 AS_Host *host = (AS_Host *) SCpnt->device->host->hostdata;
2693 int result;
2694
2695 host->stats.aborts += 1;
2696
2697#if (DEBUG & DEBUG_ABORT)
2698 {
2699 int asr, ssr;
Russell Kingffd78582008-04-19 14:26:18 +01002700 asr = sbic_arm_read(host, SBIC_ASR);
2701 ssr = sbic_arm_read(host, SBIC_SSR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002702
2703 printk(KERN_WARNING "acornscsi_abort: ");
2704 print_sbic_status(asr, ssr, host->scsi.phase);
2705 acornscsi_dumplog(host, SCpnt->device->id);
2706 }
2707#endif
2708
2709 printk("scsi%d: ", host->host->host_no);
2710
2711 switch (acornscsi_do_abort(host, SCpnt)) {
2712 /*
2713 * We managed to find the command and cleared it out.
2714 * We do not expect the command to be executing on the
2715 * target, but we have set the busylun bit.
2716 */
2717 case res_success_clear:
2718//#if (DEBUG & DEBUG_ABORT)
2719 printk("clear ");
2720//#endif
2721 clear_bit(SCpnt->device->id * 8 + SCpnt->device->lun, host->busyluns);
2722
2723 /*
2724 * We found the command, and cleared it out. Either
2725 * the command is still known to be executing on the
2726 * target, or the busylun bit is not set.
2727 */
2728 case res_success:
2729//#if (DEBUG & DEBUG_ABORT)
2730 printk("success\n");
2731//#endif
Russell King324b93372008-04-19 15:13:45 +01002732 result = SUCCESS;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002733 break;
2734
2735 /*
2736 * We did find the command, but unfortunately we couldn't
2737 * unhook it from ourselves. Wait some more, and if it
2738 * still doesn't complete, reset the interface.
2739 */
2740 case res_snooze:
2741//#if (DEBUG & DEBUG_ABORT)
2742 printk("snooze\n");
2743//#endif
Russell King324b93372008-04-19 15:13:45 +01002744 result = FAILED;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002745 break;
2746
2747 /*
2748 * The command could not be found (either because it completed,
2749 * or it got dropped.
2750 */
2751 default:
2752 case res_not_running:
2753 acornscsi_dumplog(host, SCpnt->device->id);
Russell King324b93372008-04-19 15:13:45 +01002754 result = FAILED;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002755//#if (DEBUG & DEBUG_ABORT)
2756 printk("not running\n");
2757//#endif
2758 break;
2759 }
2760
2761 return result;
2762}
2763
2764/*
Russell King324b93372008-04-19 15:13:45 +01002765 * Prototype: int acornscsi_reset(struct scsi_cmnd *SCpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002766 * Purpose : reset a command on this host/reset this host
2767 * Params : SCpnt - command causing reset
Linus Torvalds1da177e2005-04-16 15:20:36 -07002768 * Returns : one of SCSI_RESET_ macros
2769 */
Russell King324b93372008-04-19 15:13:45 +01002770int acornscsi_bus_reset(struct scsi_cmnd *SCpnt)
Linus Torvalds1da177e2005-04-16 15:20:36 -07002771{
Henneee0ca6b2006-10-01 13:18:37 +02002772 AS_Host *host = (AS_Host *)SCpnt->device->host->hostdata;
2773 struct scsi_cmnd *SCptr;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002774
2775 host->stats.resets += 1;
2776
2777#if (DEBUG & DEBUG_RESET)
2778 {
2779 int asr, ssr;
2780
Russell Kingffd78582008-04-19 14:26:18 +01002781 asr = sbic_arm_read(host, SBIC_ASR);
2782 ssr = sbic_arm_read(host, SBIC_SSR);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002783
2784 printk(KERN_WARNING "acornscsi_reset: ");
2785 print_sbic_status(asr, ssr, host->scsi.phase);
2786 acornscsi_dumplog(host, SCpnt->device->id);
2787 }
2788#endif
2789
2790 acornscsi_dma_stop(host);
2791
Linus Torvalds1da177e2005-04-16 15:20:36 -07002792 /*
2793 * do hard reset. This resets all devices on this host, and so we
2794 * must set the reset status on all commands.
2795 */
2796 acornscsi_resetcard(host);
2797
Linus Torvalds1da177e2005-04-16 15:20:36 -07002798 while ((SCptr = queue_remove(&host->queues.disconnected)) != NULL)
Russell King324b93372008-04-19 15:13:45 +01002799 ;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002800
Russell King324b93372008-04-19 15:13:45 +01002801 return SUCCESS;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002802}
2803
2804/*==============================================================================================
2805 * initialisation & miscellaneous support
2806 */
2807
2808/*
2809 * Function: char *acornscsi_info(struct Scsi_Host *host)
2810 * Purpose : return a string describing this interface
2811 * Params : host - host to give information on
2812 * Returns : a constant string
2813 */
2814const
2815char *acornscsi_info(struct Scsi_Host *host)
2816{
2817 static char string[100], *p;
2818
2819 p = string;
2820
2821 p += sprintf(string, "%s at port %08lX irq %d v%d.%d.%d"
2822#ifdef CONFIG_SCSI_ACORNSCSI_SYNC
2823 " SYNC"
2824#endif
2825#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
2826 " TAG"
2827#endif
2828#ifdef CONFIG_SCSI_ACORNSCSI_LINK
2829 " LINK"
2830#endif
2831#if (DEBUG & DEBUG_NO_WRITE)
Russell Kinga796ef72008-04-19 15:37:44 +01002832 " NOWRITE (" __stringify(NO_WRITE) ")"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002833#endif
2834 , host->hostt->name, host->io_port, host->irq,
2835 VER_MAJOR, VER_MINOR, VER_PATCH);
2836 return string;
2837}
2838
2839int acornscsi_proc_info(struct Scsi_Host *instance, char *buffer, char **start, off_t offset,
2840 int length, int inout)
2841{
2842 int pos, begin = 0, devidx;
Christoph Hellwigf64a1812005-10-31 18:32:08 +01002843 struct scsi_device *scd;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002844 AS_Host *host;
2845 char *p = buffer;
2846
2847 if (inout == 1)
2848 return -EINVAL;
2849
2850 host = (AS_Host *)instance->hostdata;
2851
2852 p += sprintf(p, "AcornSCSI driver v%d.%d.%d"
2853#ifdef CONFIG_SCSI_ACORNSCSI_SYNC
2854 " SYNC"
2855#endif
2856#ifdef CONFIG_SCSI_ACORNSCSI_TAGGED_QUEUE
2857 " TAG"
2858#endif
2859#ifdef CONFIG_SCSI_ACORNSCSI_LINK
2860 " LINK"
2861#endif
2862#if (DEBUG & DEBUG_NO_WRITE)
Russell Kinga796ef72008-04-19 15:37:44 +01002863 " NOWRITE (" __stringify(NO_WRITE) ")"
Linus Torvalds1da177e2005-04-16 15:20:36 -07002864#endif
2865 "\n\n", VER_MAJOR, VER_MINOR, VER_PATCH);
2866
Russell Kinge95a1b62008-04-19 15:42:57 +01002867 p += sprintf(p, "SBIC: WD33C93A Address: %p IRQ : %d\n",
2868 host->base + SBIC_REGIDX, host->scsi.irq);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002869#ifdef USE_DMAC
Russell Kinge95a1b62008-04-19 15:42:57 +01002870 p += sprintf(p, "DMAC: uPC71071 Address: %p IRQ : %d\n\n",
2871 host->base + DMAC_OFFSET, host->scsi.irq);
Linus Torvalds1da177e2005-04-16 15:20:36 -07002872#endif
2873
2874 p += sprintf(p, "Statistics:\n"
2875 "Queued commands: %-10u Issued commands: %-10u\n"
2876 "Done commands : %-10u Reads : %-10u\n"
2877 "Writes : %-10u Others : %-10u\n"
2878 "Disconnects : %-10u Aborts : %-10u\n"
2879 "Resets : %-10u\n\nLast phases:",
2880 host->stats.queues, host->stats.removes,
2881 host->stats.fins, host->stats.reads,
2882 host->stats.writes, host->stats.miscs,
2883 host->stats.disconnects, host->stats.aborts,
2884 host->stats.resets);
2885
2886 for (devidx = 0; devidx < 9; devidx ++) {
2887 unsigned int statptr, prev;
2888
2889 p += sprintf(p, "\n%c:", devidx == 8 ? 'H' : ('0' + devidx));
2890 statptr = host->status_ptr[devidx] - 10;
2891
2892 if ((signed int)statptr < 0)
2893 statptr += STATUS_BUFFER_SIZE;
2894
2895 prev = host->status[devidx][statptr].when;
2896
2897 for (; statptr != host->status_ptr[devidx]; statptr = (statptr + 1) & (STATUS_BUFFER_SIZE - 1)) {
2898 if (host->status[devidx][statptr].when) {
2899 p += sprintf(p, "%c%02X:%02X+%2ld",
2900 host->status[devidx][statptr].irq ? '-' : ' ',
2901 host->status[devidx][statptr].ph,
2902 host->status[devidx][statptr].ssr,
2903 (host->status[devidx][statptr].when - prev) < 100 ?
2904 (host->status[devidx][statptr].when - prev) : 99);
2905 prev = host->status[devidx][statptr].when;
2906 }
2907 }
2908 }
2909
2910 p += sprintf(p, "\nAttached devices:\n");
2911
2912 shost_for_each_device(scd, instance) {
2913 p += sprintf(p, "Device/Lun TaggedQ Sync\n");
2914 p += sprintf(p, " %d/%d ", scd->id, scd->lun);
2915 if (scd->tagged_supported)
2916 p += sprintf(p, "%3sabled(%3d) ",
2917 scd->simple_tags ? "en" : "dis",
2918 scd->current_tag);
2919 else
2920 p += sprintf(p, "unsupported ");
2921
2922 if (host->device[scd->id].sync_xfer & 15)
2923 p += sprintf(p, "offset %d, %d ns\n",
2924 host->device[scd->id].sync_xfer & 15,
2925 acornscsi_getperiod(host->device[scd->id].sync_xfer));
2926 else
2927 p += sprintf(p, "async\n");
2928
2929 pos = p - buffer;
2930 if (pos + begin < offset) {
2931 begin += pos;
2932 p = buffer;
2933 }
2934 pos = p - buffer;
2935 if (pos + begin > offset + length) {
2936 scsi_device_put(scd);
2937 break;
2938 }
2939 }
2940
2941 pos = p - buffer;
2942
2943 *start = buffer + (offset - begin);
2944 pos -= offset - begin;
2945
2946 if (pos > length)
2947 pos = length;
2948
2949 return pos;
2950}
2951
Christoph Hellwigd0be4a7d2005-10-31 18:31:40 +01002952static struct scsi_host_template acornscsi_template = {
Linus Torvalds1da177e2005-04-16 15:20:36 -07002953 .module = THIS_MODULE,
2954 .proc_info = acornscsi_proc_info,
2955 .name = "AcornSCSI",
2956 .info = acornscsi_info,
2957 .queuecommand = acornscsi_queuecmd,
Russell King324b93372008-04-19 15:13:45 +01002958 .eh_abort_handler = acornscsi_abort,
2959 .eh_bus_reset_handler = acornscsi_bus_reset,
Linus Torvalds1da177e2005-04-16 15:20:36 -07002960 .can_queue = 16,
2961 .this_id = 7,
2962 .sg_tablesize = SG_ALL,
2963 .cmd_per_lun = 2,
Linus Torvalds1da177e2005-04-16 15:20:36 -07002964 .use_clustering = DISABLE_CLUSTERING,
2965 .proc_name = "acornscsi",
2966};
2967
2968static int __devinit
2969acornscsi_probe(struct expansion_card *ec, const struct ecard_id *id)
2970{
2971 struct Scsi_Host *host;
2972 AS_Host *ashost;
Russell Kinge95a1b62008-04-19 15:42:57 +01002973 int ret;
2974
2975 ret = ecard_request_resources(ec);
2976 if (ret)
2977 goto out;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002978
2979 host = scsi_host_alloc(&acornscsi_template, sizeof(AS_Host));
Russell Kinge95a1b62008-04-19 15:42:57 +01002980 if (!host) {
2981 ret = -ENOMEM;
2982 goto out_release;
2983 }
Linus Torvalds1da177e2005-04-16 15:20:36 -07002984
2985 ashost = (AS_Host *)host->hostdata;
2986
Russell Kinge95a1b62008-04-19 15:42:57 +01002987 ashost->base = ecardm_iomap(ec, ECARD_RES_MEMC, 0, 0);
2988 ashost->fast = ecardm_iomap(ec, ECARD_RES_IOCFAST, 0, 0);
2989 if (!ashost->base || !ashost->fast)
2990 goto out_put;
2991
Linus Torvalds1da177e2005-04-16 15:20:36 -07002992 host->irq = ec->irq;
Russell Kinge95a1b62008-04-19 15:42:57 +01002993 ashost->host = host;
2994 ashost->scsi.irq = host->irq;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002995
Russell Kinge95a1b62008-04-19 15:42:57 +01002996 ec->irqaddr = ashost->fast + INT_REG;
Linus Torvalds1da177e2005-04-16 15:20:36 -07002997 ec->irqmask = 0x0a;
2998
Thomas Gleixner1d6f3592006-07-01 19:29:42 -07002999 ret = request_irq(host->irq, acornscsi_intr, IRQF_DISABLED, "acornscsi", ashost);
Linus Torvalds1da177e2005-04-16 15:20:36 -07003000 if (ret) {
3001 printk(KERN_CRIT "scsi%d: IRQ%d not free: %d\n",
3002 host->host_no, ashost->scsi.irq, ret);
Russell Kinge95a1b62008-04-19 15:42:57 +01003003 goto out_put;
Linus Torvalds1da177e2005-04-16 15:20:36 -07003004 }
3005
3006 memset(&ashost->stats, 0, sizeof (ashost->stats));
3007 queue_initialise(&ashost->queues.issue);
3008 queue_initialise(&ashost->queues.disconnected);
3009 msgqueue_initialise(&ashost->scsi.msgs);
3010
3011 acornscsi_resetcard(ashost);
3012
3013 ret = scsi_add_host(host, &ec->dev);
3014 if (ret)
Russell Kinge95a1b62008-04-19 15:42:57 +01003015 goto out_irq;
Linus Torvalds1da177e2005-04-16 15:20:36 -07003016
3017 scsi_scan_host(host);
3018 goto out;
3019
Russell Kinge95a1b62008-04-19 15:42:57 +01003020 out_irq:
Linus Torvalds1da177e2005-04-16 15:20:36 -07003021 free_irq(host->irq, ashost);
Russell Kinge95a1b62008-04-19 15:42:57 +01003022 msgqueue_free(&ashost->scsi.msgs);
3023 queue_free(&ashost->queues.disconnected);
3024 queue_free(&ashost->queues.issue);
3025 out_put:
3026 ecardm_iounmap(ec, ashost->fast);
3027 ecardm_iounmap(ec, ashost->base);
Linus Torvalds1da177e2005-04-16 15:20:36 -07003028 scsi_host_put(host);
Russell Kinge95a1b62008-04-19 15:42:57 +01003029 out_release:
3030 ecard_release_resources(ec);
Linus Torvalds1da177e2005-04-16 15:20:36 -07003031 out:
3032 return ret;
3033}
3034
3035static void __devexit acornscsi_remove(struct expansion_card *ec)
3036{
3037 struct Scsi_Host *host = ecard_get_drvdata(ec);
3038 AS_Host *ashost = (AS_Host *)host->hostdata;
3039
3040 ecard_set_drvdata(ec, NULL);
3041 scsi_remove_host(host);
3042
3043 /*
3044 * Put card into RESET state
3045 */
Russell Kinge95a1b62008-04-19 15:42:57 +01003046 writeb(0x80, ashost->fast + PAGE_REG);
Linus Torvalds1da177e2005-04-16 15:20:36 -07003047
3048 free_irq(host->irq, ashost);
3049
Linus Torvalds1da177e2005-04-16 15:20:36 -07003050 msgqueue_free(&ashost->scsi.msgs);
3051 queue_free(&ashost->queues.disconnected);
3052 queue_free(&ashost->queues.issue);
Russell Kinge95a1b62008-04-19 15:42:57 +01003053 ecardm_iounmap(ec, ashost->fast);
3054 ecardm_iounmap(ec, ashost->base);
Linus Torvalds1da177e2005-04-16 15:20:36 -07003055 scsi_host_put(host);
Russell Kinge95a1b62008-04-19 15:42:57 +01003056 ecard_release_resources(ec);
Linus Torvalds1da177e2005-04-16 15:20:36 -07003057}
3058
3059static const struct ecard_id acornscsi_cids[] = {
3060 { MANU_ACORN, PROD_ACORN_SCSI },
3061 { 0xffff, 0xffff },
3062};
3063
3064static struct ecard_driver acornscsi_driver = {
3065 .probe = acornscsi_probe,
3066 .remove = __devexit_p(acornscsi_remove),
3067 .id_table = acornscsi_cids,
3068 .drv = {
3069 .name = "acornscsi",
3070 },
3071};
3072
3073static int __init acornscsi_init(void)
3074{
3075 return ecard_register_driver(&acornscsi_driver);
3076}
3077
3078static void __exit acornscsi_exit(void)
3079{
3080 ecard_remove_driver(&acornscsi_driver);
3081}
3082
3083module_init(acornscsi_init);
3084module_exit(acornscsi_exit);
3085
3086MODULE_AUTHOR("Russell King");
3087MODULE_DESCRIPTION("AcornSCSI driver");
3088MODULE_LICENSE("GPL");