| R.Marek@sh.cvut.cz | 7f15b66 | 2005-05-26 12:42:19 +0000 | [diff] [blame] | 1 | Kernel driver lm75 |
| 2 | ================== |
| 3 | |
| 4 | Supported chips: |
| 5 | * National Semiconductor LM75 |
| 6 | Prefix: 'lm75' |
| 7 | Addresses scanned: I2C 0x48 - 0x4f |
| 8 | Datasheet: Publicly available at the National Semiconductor website |
| 9 | http://www.national.com/ |
| Len Sorensen | 05e82fe | 2011-03-21 17:59:36 +0100 | [diff] [blame] | 10 | * National Semiconductor LM75A |
| 11 | Prefix: 'lm75a' |
| 12 | Addresses scanned: I2C 0x48 - 0x4f |
| 13 | Datasheet: Publicly available at the National Semiconductor website |
| 14 | http://www.national.com/ |
| R.Marek@sh.cvut.cz | 7f15b66 | 2005-05-26 12:42:19 +0000 | [diff] [blame] | 15 | * Dallas Semiconductor DS75 |
| 16 | Prefix: 'lm75' |
| 17 | Addresses scanned: I2C 0x48 - 0x4f |
| 18 | Datasheet: Publicly available at the Dallas Semiconductor website |
| 19 | http://www.maxim-ic.com/ |
| 20 | * Dallas Semiconductor DS1775 |
| 21 | Prefix: 'lm75' |
| 22 | Addresses scanned: I2C 0x48 - 0x4f |
| 23 | Datasheet: Publicly available at the Dallas Semiconductor website |
| 24 | http://www.maxim-ic.com/ |
| 25 | * Maxim MAX6625, MAX6626 |
| 26 | Prefix: 'lm75' |
| 27 | Addresses scanned: I2C 0x48 - 0x4b |
| 28 | Datasheet: Publicly available at the Maxim website |
| 29 | http://www.maxim-ic.com/ |
| 30 | * Microchip (TelCom) TCN75 |
| 31 | Prefix: 'lm75' |
| 32 | Addresses scanned: I2C 0x48 - 0x4f |
| 33 | Datasheet: Publicly available at the Microchip website |
| 34 | http://www.microchip.com/ |
| 35 | |
| 36 | Author: Frodo Looijaard <frodol@dds.nl> |
| 37 | |
| 38 | Description |
| 39 | ----------- |
| 40 | |
| 41 | The LM75 implements one temperature sensor. Limits can be set through the |
| 42 | Overtemperature Shutdown register and Hysteresis register. Each value can be |
| 43 | set and read to half-degree accuracy. |
| 44 | An alarm is issued (usually to a connected LM78) when the temperature |
| 45 | gets higher then the Overtemperature Shutdown value; it stays on until |
| 46 | the temperature falls below the Hysteresis value. |
| 47 | All temperatures are in degrees Celsius, and are guaranteed within a |
| 48 | range of -55 to +125 degrees. |
| 49 | |
| 50 | The LM75 only updates its values each 1.5 seconds; reading it more often |
| 51 | will do no harm, but will return 'old' values. |
| 52 | |
| 53 | The LM75 is usually used in combination with LM78-like chips, to measure |
| 54 | the temperature of the processor(s). |
| 55 | |
| 56 | The DS75, DS1775, MAX6625, and MAX6626 are supported as well. |
| 57 | They are not distinguished from an LM75. While most of these chips |
| 58 | have three additional bits of accuracy (12 vs. 9 for the LM75), |
| 59 | the additional bits are not supported. Not only that, but these chips will |
| 60 | not be detected if not in 9-bit precision mode (use the force parameter if |
| 61 | needed). |
| 62 | |
| 63 | The TCN75 is supported as well, and is not distinguished from an LM75. |
| 64 | |
| 65 | The LM75 is essentially an industry standard; there may be other |
| 66 | LM75 clones not listed here, with or without various enhancements, |
| 67 | that are supported. |
| 68 | |
| 69 | The LM77 is not supported, contrary to what we pretended for a long time. |
| 70 | Both chips are simply not compatible, value encoding differs. |