| Bruno Prémont | 236db47 | 2010-03-30 22:33:50 +0200 | [diff] [blame] | 1 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode |
| 2 | Date: March 2010 |
| 3 | Contact: Bruno Prémont <bonbons@linux-vserver.org> |
| 4 | Description: Make it possible to switch the PicoLCD device between LCD |
| 5 | (firmware) and bootloader (flasher) operation modes. |
| 6 | |
| 7 | Reading: returns list of available modes, the active mode being |
| 8 | enclosed in brackets ('[' and ']') |
| 9 | |
| 10 | Writing: causes operation mode switch. Permitted values are |
| Bruno Prémont | 0b5adf9 | 2010-04-25 21:29:16 +0200 | [diff] [blame] | 11 | the non-active mode names listed when read. |
| Bruno Prémont | 236db47 | 2010-03-30 22:33:50 +0200 | [diff] [blame] | 12 | |
| 13 | Note: when switching mode the current PicoLCD HID device gets |
| Bruno Prémont | 0b5adf9 | 2010-04-25 21:29:16 +0200 | [diff] [blame] | 14 | disconnected and reconnects after above delay (see attribute |
| 15 | operation_mode_delay for its value). |
| 16 | |
| 17 | |
| 18 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/operation_mode_delay |
| 19 | Date: April 2010 |
| 20 | Contact: Bruno Prémont <bonbons@linux-vserver.org> |
| 21 | Description: Delay PicoLCD waits before restarting in new mode when |
| 22 | operation_mode has changed. |
| 23 | |
| 24 | Reading/Writing: It is expressed in ms and permitted range is |
| 25 | 0..30000ms. |
| Bruno Prémont | 236db47 | 2010-03-30 22:33:50 +0200 | [diff] [blame] | 26 | |
| Bruno Prémont | b8c21cf | 2010-03-30 22:34:30 +0200 | [diff] [blame] | 27 | |
| 28 | What: /sys/bus/usb/devices/<busnum>-<devnum>:<config num>.<interface num>/<hid-bus>:<vendor-id>:<product-id>.<num>/fb_update_rate |
| 29 | Date: March 2010 |
| 30 | Contact: Bruno Prémont <bonbons@linux-vserver.org> |
| 31 | Description: Make it possible to adjust defio refresh rate. |
| 32 | |
| 33 | Reading: returns list of available refresh rates (expressed in Hz), |
| 34 | the active refresh rate being enclosed in brackets ('[' and ']') |
| 35 | |
| 36 | Writing: accepts new refresh rate expressed in integer Hz |
| 37 | within permitted rates. |
| 38 | |
| 39 | Note: As device can barely do 2 complete refreshes a second |
| 40 | it only makes sense to adjust this value if only one or two |
| 41 | tiles get changed and it's not appropriate to expect the application |
| 42 | to flush it's tiny changes explicitely at higher than default rate. |
| 43 | |