blob: d65cb9d2fa8c1966dc8c33c1a535a580b7bea3d2 [file] [log] [blame]
Jeff Garzik669a5db2006-08-29 18:12:40 -04001/*
2 * IDE tuning and bus mastering support for the CS5510/CS5520
3 * chipsets
4 *
5 * The CS5510/CS5520 are slightly unusual devices. Unlike the
6 * typical IDE controllers they do bus mastering with the drive in
7 * PIO mode and smarter silicon.
8 *
9 * The practical upshot of this is that we must always tune the
10 * drive for the right PIO mode. We must also ignore all the blacklists
11 * and the drive bus mastering DMA information. Also to confuse matters
12 * further we can do DMA on PIO only drives.
13 *
14 * DMA on the 5510 also requires we disable_hlt() during DMA on early
15 * revisions.
16 *
17 * *** This driver is strictly experimental ***
18 *
19 * (c) Copyright Red Hat Inc 2002
20 *
21 * This program is free software; you can redistribute it and/or modify it
22 * under the terms of the GNU General Public License as published by the
23 * Free Software Foundation; either version 2, or (at your option) any
24 * later version.
25 *
26 * This program is distributed in the hope that it will be useful, but
27 * WITHOUT ANY WARRANTY; without even the implied warranty of
28 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
29 * General Public License for more details.
30 *
31 * Documentation:
Lucas De Marchi25985ed2011-03-30 22:57:33 -030032 * Not publicly available.
Jeff Garzik669a5db2006-08-29 18:12:40 -040033 */
34#include <linux/kernel.h>
35#include <linux/module.h>
36#include <linux/pci.h>
Jeff Garzik669a5db2006-08-29 18:12:40 -040037#include <linux/blkdev.h>
38#include <linux/delay.h>
39#include <scsi/scsi_host.h>
40#include <linux/libata.h>
41
42#define DRV_NAME "pata_cs5520"
Jeff Garzik2a3103c2007-08-31 04:54:06 -040043#define DRV_VERSION "0.6.6"
Jeff Garzik669a5db2006-08-29 18:12:40 -040044
45struct pio_clocks
46{
47 int address;
48 int assert;
49 int recovery;
50};
51
52static const struct pio_clocks cs5520_pio_clocks[]={
53 {3, 6, 11},
54 {2, 5, 6},
55 {1, 4, 3},
56 {1, 3, 2},
57 {1, 2, 1}
58};
59
60/**
61 * cs5520_set_timings - program PIO timings
62 * @ap: ATA port
63 * @adev: ATA device
64 *
65 * Program the PIO mode timings for the controller according to the pio
66 * clocking table.
67 */
68
69static void cs5520_set_timings(struct ata_port *ap, struct ata_device *adev, int pio)
70{
71 struct pci_dev *pdev = to_pci_dev(ap->host->dev);
72 int slave = adev->devno;
73
74 pio -= XFER_PIO_0;
75
76 /* Channel command timing */
77 pci_write_config_byte(pdev, 0x62 + ap->port_no,
78 (cs5520_pio_clocks[pio].recovery << 4) |
79 (cs5520_pio_clocks[pio].assert));
80 /* FIXME: should these use address ? */
81 /* Read command timing */
82 pci_write_config_byte(pdev, 0x64 + 4*ap->port_no + slave,
83 (cs5520_pio_clocks[pio].recovery << 4) |
84 (cs5520_pio_clocks[pio].assert));
85 /* Write command timing */
86 pci_write_config_byte(pdev, 0x66 + 4*ap->port_no + slave,
87 (cs5520_pio_clocks[pio].recovery << 4) |
88 (cs5520_pio_clocks[pio].assert));
89}
90
91/**
Jeff Garzik669a5db2006-08-29 18:12:40 -040092 * cs5520_set_piomode - program PIO timings
93 * @ap: ATA port
94 * @adev: ATA device
95 *
96 * Program the PIO mode timings for the controller according to the pio
Bartlomiej Zolnierkiewicz940a68d2009-12-03 20:32:09 +010097 * clocking table.
Jeff Garzik669a5db2006-08-29 18:12:40 -040098 */
99
100static void cs5520_set_piomode(struct ata_port *ap, struct ata_device *adev)
101{
102 cs5520_set_timings(ap, adev, adev->pio_mode);
103}
104
Jeff Garzik669a5db2006-08-29 18:12:40 -0400105static struct scsi_host_template cs5520_sht = {
Tejun Heo68d1d072008-03-25 12:22:49 +0900106 ATA_BMDMA_SHT(DRV_NAME),
Alan Coxd26fc952007-07-06 19:13:52 -0400107 .sg_tablesize = LIBATA_DUMB_MAX_PRD,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400108};
109
110static struct ata_port_operations cs5520_port_ops = {
Tejun Heo029cfd62008-03-25 12:22:49 +0900111 .inherits = &ata_bmdma_port_ops,
Tejun Heof47451c2010-05-10 21:41:40 +0200112 .qc_prep = ata_bmdma_dumb_qc_prep,
Tejun Heo029cfd62008-03-25 12:22:49 +0900113 .cable_detect = ata_cable_40wire,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400114 .set_piomode = cs5520_set_piomode,
Jeff Garzik669a5db2006-08-29 18:12:40 -0400115};
116
Greg Kroah-Hartman0ec24912012-12-21 13:19:58 -0800117static int cs5520_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
Jeff Garzik669a5db2006-08-29 18:12:40 -0400118{
Tejun Heocbcdd872007-08-18 13:14:55 +0900119 static const unsigned int cmd_port[] = { 0x1F0, 0x170 };
120 static const unsigned int ctl_port[] = { 0x3F6, 0x376 };
Tejun Heo5d728822007-04-17 23:44:08 +0900121 struct ata_port_info pi = {
122 .flags = ATA_FLAG_SLAVE_POSS,
Erik Inge Bolsø14bdef92009-03-14 21:38:24 +0100123 .pio_mask = ATA_PIO4,
Tejun Heo5d728822007-04-17 23:44:08 +0900124 .port_ops = &cs5520_port_ops,
125 };
126 const struct ata_port_info *ppi[2];
Jeff Garzik669a5db2006-08-29 18:12:40 -0400127 u8 pcicfg;
Al Viro4ca4e432007-12-30 09:32:22 +0000128 void __iomem *iomap[5];
Tejun Heo5d728822007-04-17 23:44:08 +0900129 struct ata_host *host;
130 struct ata_ioports *ioaddr;
131 int i, rc;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400132
Tejun Heof08048e2008-03-25 12:22:47 +0900133 rc = pcim_enable_device(pdev);
134 if (rc)
135 return rc;
136
Jeff Garzik669a5db2006-08-29 18:12:40 -0400137 /* IDE port enable bits */
Tejun Heo5d728822007-04-17 23:44:08 +0900138 pci_read_config_byte(pdev, 0x60, &pcicfg);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400139
140 /* Check if the ATA ports are enabled */
141 if ((pcicfg & 3) == 0)
142 return -ENODEV;
143
Tejun Heo5d728822007-04-17 23:44:08 +0900144 ppi[0] = ppi[1] = &ata_dummy_port_info;
145 if (pcicfg & 1)
146 ppi[0] = &pi;
147 if (pcicfg & 2)
148 ppi[1] = &pi;
149
Jeff Garzik669a5db2006-08-29 18:12:40 -0400150 if ((pcicfg & 0x40) == 0) {
Joe Perchesa44fec12011-04-15 15:51:58 -0700151 dev_warn(&pdev->dev, "DMA mode disabled. Enabling.\n");
Tejun Heo5d728822007-04-17 23:44:08 +0900152 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400153 }
154
Tejun Heo5d728822007-04-17 23:44:08 +0900155 pi.mwdma_mask = id->driver_data;
156
157 host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
158 if (!host)
159 return -ENOMEM;
160
Jeff Garzik669a5db2006-08-29 18:12:40 -0400161 /* Perform set up for DMA */
Benjamin Herrenschmidt09483912007-12-20 15:28:09 +1100162 if (pci_enable_device_io(pdev)) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400163 printk(KERN_ERR DRV_NAME ": unable to configure BAR2.\n");
164 return -ENODEV;
165 }
Tejun Heo5d728822007-04-17 23:44:08 +0900166
Yang Hongyang284901a2009-04-06 19:01:15 -0700167 if (pci_set_dma_mask(pdev, DMA_BIT_MASK(32))) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400168 printk(KERN_ERR DRV_NAME ": unable to configure DMA mask.\n");
169 return -ENODEV;
170 }
Yang Hongyang284901a2009-04-06 19:01:15 -0700171 if (pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32))) {
Jeff Garzik669a5db2006-08-29 18:12:40 -0400172 printk(KERN_ERR DRV_NAME ": unable to configure consistent DMA mask.\n");
173 return -ENODEV;
174 }
175
Tejun Heo5d728822007-04-17 23:44:08 +0900176 /* Map IO ports and initialize host accordingly */
Tejun Heocbcdd872007-08-18 13:14:55 +0900177 iomap[0] = devm_ioport_map(&pdev->dev, cmd_port[0], 8);
178 iomap[1] = devm_ioport_map(&pdev->dev, ctl_port[0], 1);
179 iomap[2] = devm_ioport_map(&pdev->dev, cmd_port[1], 8);
180 iomap[3] = devm_ioport_map(&pdev->dev, ctl_port[1], 1);
Tejun Heo5d728822007-04-17 23:44:08 +0900181 iomap[4] = pcim_iomap(pdev, 2, 0);
Tejun Heo0d5ff562007-02-01 15:06:36 +0900182
183 if (!iomap[0] || !iomap[1] || !iomap[2] || !iomap[3] || !iomap[4])
184 return -ENOMEM;
185
Tejun Heo5d728822007-04-17 23:44:08 +0900186 ioaddr = &host->ports[0]->ioaddr;
187 ioaddr->cmd_addr = iomap[0];
188 ioaddr->ctl_addr = iomap[1];
189 ioaddr->altstatus_addr = iomap[1];
190 ioaddr->bmdma_addr = iomap[4];
Tejun Heo9363c382008-04-07 22:47:16 +0900191 ata_sff_std_ports(ioaddr);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400192
Tejun Heocbcdd872007-08-18 13:14:55 +0900193 ata_port_desc(host->ports[0],
194 "cmd 0x%x ctl 0x%x", cmd_port[0], ctl_port[0]);
195 ata_port_pbar_desc(host->ports[0], 4, 0, "bmdma");
196
Tejun Heo5d728822007-04-17 23:44:08 +0900197 ioaddr = &host->ports[1]->ioaddr;
198 ioaddr->cmd_addr = iomap[2];
199 ioaddr->ctl_addr = iomap[3];
200 ioaddr->altstatus_addr = iomap[3];
201 ioaddr->bmdma_addr = iomap[4] + 8;
Tejun Heo9363c382008-04-07 22:47:16 +0900202 ata_sff_std_ports(ioaddr);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400203
Tejun Heocbcdd872007-08-18 13:14:55 +0900204 ata_port_desc(host->ports[1],
205 "cmd 0x%x ctl 0x%x", cmd_port[1], ctl_port[1]);
206 ata_port_pbar_desc(host->ports[1], 4, 8, "bmdma");
207
Tejun Heo5d728822007-04-17 23:44:08 +0900208 /* activate the host */
209 pci_set_master(pdev);
210 rc = ata_host_start(host);
211 if (rc)
212 return rc;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400213
Tejun Heo5d728822007-04-17 23:44:08 +0900214 for (i = 0; i < 2; i++) {
215 static const int irq[] = { 14, 15 };
Alan Cox8c6b0652007-07-20 15:36:31 +0100216 struct ata_port *ap = host->ports[i];
Jeff Garzik669a5db2006-08-29 18:12:40 -0400217
Tejun Heo5d728822007-04-17 23:44:08 +0900218 if (ata_port_is_dummy(ap))
219 continue;
Jeff Garzik669a5db2006-08-29 18:12:40 -0400220
Tejun Heo5d728822007-04-17 23:44:08 +0900221 rc = devm_request_irq(&pdev->dev, irq[ap->port_no],
Tejun Heoc3b28892010-05-19 22:10:21 +0200222 ata_bmdma_interrupt, 0, DRV_NAME, host);
Tejun Heo5d728822007-04-17 23:44:08 +0900223 if (rc)
224 return rc;
Tejun Heo40318262007-07-03 01:38:47 +0900225
Tejun Heocbcdd872007-08-18 13:14:55 +0900226 ata_port_desc(ap, "irq %d", irq[i]);
Tejun Heo5d728822007-04-17 23:44:08 +0900227 }
228
229 return ata_host_register(host, &cs5520_sht);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400230}
231
Bartlomiej Zolnierkiewicz58eb8cd2014-05-07 17:17:44 +0200232#ifdef CONFIG_PM_SLEEP
Alan85011202006-11-22 17:01:06 +0000233/**
234 * cs5520_reinit_one - device resume
235 * @pdev: PCI device
236 *
237 * Do any reconfiguration work needed by a resume from RAM. We need
238 * to restore DMA mode support on BIOSen which disabled it
239 */
Jeff Garzikf20b16f2006-12-11 11:14:06 -0500240
Alan85011202006-11-22 17:01:06 +0000241static int cs5520_reinit_one(struct pci_dev *pdev)
242{
Jingoo Han0a86e1c2013-06-03 14:05:36 +0900243 struct ata_host *host = pci_get_drvdata(pdev);
Alan85011202006-11-22 17:01:06 +0000244 u8 pcicfg;
Tejun Heof08048e2008-03-25 12:22:47 +0900245 int rc;
246
247 rc = ata_pci_device_do_resume(pdev);
248 if (rc)
249 return rc;
250
Alan85011202006-11-22 17:01:06 +0000251 pci_read_config_byte(pdev, 0x60, &pcicfg);
252 if ((pcicfg & 0x40) == 0)
253 pci_write_config_byte(pdev, 0x60, pcicfg | 0x40);
Tejun Heof08048e2008-03-25 12:22:47 +0900254
255 ata_host_resume(host);
256 return 0;
Alan85011202006-11-22 17:01:06 +0000257}
Alanaa6de492007-02-20 17:44:25 +0000258
259/**
260 * cs5520_pci_device_suspend - device suspend
261 * @pdev: PCI device
262 *
263 * We have to cut and waste bits from the standard method because
264 * the 5520 is a bit odd and not just a pure ATA device. As a result
265 * we must not disable it. The needed code is short and this avoids
266 * chip specific mess in the core code.
267 */
268
269static int cs5520_pci_device_suspend(struct pci_dev *pdev, pm_message_t mesg)
270{
Jingoo Han0a86e1c2013-06-03 14:05:36 +0900271 struct ata_host *host = pci_get_drvdata(pdev);
Alanaa6de492007-02-20 17:44:25 +0000272 int rc = 0;
273
274 rc = ata_host_suspend(host, mesg);
275 if (rc)
276 return rc;
277
278 pci_save_state(pdev);
279 return 0;
280}
Bartlomiej Zolnierkiewicz58eb8cd2014-05-07 17:17:44 +0200281#endif /* CONFIG_PM_SLEEP */
Jeff Garzika84471f2007-02-26 05:51:33 -0500282
Jeff Garzik669a5db2006-08-29 18:12:40 -0400283/* For now keep DMA off. We can set it for all but A rev CS5510 once the
284 core ATA code can handle it */
285
Jeff Garzik2d2744f2006-09-28 20:21:59 -0400286static const struct pci_device_id pata_cs5520[] = {
287 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), },
288 { PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), },
289
290 { },
Jeff Garzik669a5db2006-08-29 18:12:40 -0400291};
292
293static struct pci_driver cs5520_pci_driver = {
294 .name = DRV_NAME,
295 .id_table = pata_cs5520,
296 .probe = cs5520_init_one,
Jeff Garzik28555682007-10-11 17:12:35 -0400297 .remove = ata_pci_remove_one,
Bartlomiej Zolnierkiewicz58eb8cd2014-05-07 17:17:44 +0200298#ifdef CONFIG_PM_SLEEP
Alanaa6de492007-02-20 17:44:25 +0000299 .suspend = cs5520_pci_device_suspend,
Alan85011202006-11-22 17:01:06 +0000300 .resume = cs5520_reinit_one,
Tejun Heo438ac6d2007-03-02 17:31:26 +0900301#endif
Jeff Garzik669a5db2006-08-29 18:12:40 -0400302};
303
Axel Lin2fc75da2012-04-19 13:43:05 +0800304module_pci_driver(cs5520_pci_driver);
Jeff Garzik669a5db2006-08-29 18:12:40 -0400305
306MODULE_AUTHOR("Alan Cox");
307MODULE_DESCRIPTION("low-level driver for Cyrix CS5510/5520");
308MODULE_LICENSE("GPL");
309MODULE_DEVICE_TABLE(pci, pata_cs5520);
310MODULE_VERSION(DRV_VERSION);